# Leonardo Service Bulletin 412-160: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0607, the docket of AD 2021-16-04. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Service Bulletin 412-160](https://openairdocs.org/service-documents/leonardo/sb-412-160.md)
- Title as filed: Leonardo Helicopters SB 412-160 Rev 0
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/92/5c/925cacd9764e5c1180eb4570336001699e42aa783ae3a2336fa47c29c7783bfd
- Page: https://openairdocs.org/service-documents/leonardo/sb-412-160/file/925cacd9764e

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 412-160 
DATE:  August 13, 2020 
REV. :  / - March 15, 2017 
Page 1 of 11 
TITLE 
ATA 24 - EMERGENCY BUS INTERLOCK COMPARTMENT, INSPECTION OF 
REVISION LOG 
New Issue 
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
SERVICE BULLETIN

### Page 2

S.B. N°412-160 
 DATE: August 13, 2020 
Page 2 of 11 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
All AB412/AB412EP helicopters. 
B. COMPLIANCE 
Within 25 flight hours or 3 months whichever occurs first after the issue of this Service 
Bulletin 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction on how to 
perform a one-off inspection of the grommet installed on the emergency bus interlock 
compartment at STA 63.30 (1608 mm). 
E. DESCRIPTION 
An AB412EP in service reported the activation of the N o. 1 and N o.2 Inverter Caution 
Lights on the Warning and Caution Panel, with the consequent Autopilot 
disengagement. 
Further investigation revealed that the cause of the malfunction was a failure for 
chafing of a wire, part of the AC PWR SYS C/A, due to a protective grommet not  
properly installed in the emergency bus interlock compartment. 
Leonardo Helicopters, as a precautionary measure, issued this Service Bulletin in 
order to provide the instructions to perform a one -time inspection to verify the existing 
clearance between grommet and the wires passing through it. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, a pplicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the

### Page 3

S.B. N°412-160 
DATE: August 13, 2020 
REVISION: / Page 3 of 11 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin, approximately 0.5 MMH are deemed necessary: 
MMH are based on hands -on time and can change wi th personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
AB412-MM Maintenance Manual 
BHT-ELEC-SPM Electrical Standard Practice Manual 
BHT-ALL-SRM  Structural Repair Manual 
2) ACRONYMS 
C/A Cable Assy 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LHD Leonardo Helicopters 
MM Maintenance Manual 
MMH Maintenance Man Hours 
P/N Part Number 
SB Service Bulletin 
SPM Standard Practice Manual 
SRM Structural Repair Manual 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 4

S.B. N°412-160 
 DATE: August 13, 2020 
Page 4 of 11 REVISION: / 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
The following materials may be necessary to accomplish this Service Bulletin: 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 M22759/41-18-9  Wire, Electrical AR .  - 
2 MS21266-1N  Grommet AR .  - 
2) CONSUMABLES 
The following consumable materials, or equivalent, may be  necessary to 
accomplish this Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
3 Commercial (cod. 500204530) Adhesive EC847/1236 AR (1) - 
4 MIL-DTL-81706, class 1A, form III Chemical Film, Alodine 1201  AR (1) - 
5 ML-PRF-23377, type I or II, class C2 Epoxy Polyamide Primer AR (1) - 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
 Item to be procured as local supply 
B. SPECIAL TOOLS 
N.A. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
than the applicable date in the “Compliance” section will be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.

### Page 5

S.B. N°412-160 
DATE: August 13, 2020 
REVISION: / Page 5 of 11 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
b) Shape t he cables in order to prevent interference 
with the structure and the other existing 
installations, using where necessary suitable lacing 
cords. 
c) Let adhesive cure at room temperature for at least 
24 hours unless otherwise specified. 
d) All lengths are in mm. 
1. In accordance with the instructions given in the AB412 -MM Maintenance Manual, 
prepare the helicopter on ground for a safe maintenance; disconnect the battery and any 
source of electrical power supply. 
2. With reference to Figure 1  and in accordance with  the instructions given in the  
AB412-MM Maintenance Manual, gain access to emergency bus interlock compartment 
(STA 1608). 
3. With reference to Figures 2 and 3, verify there is a sufficient clearance between the C/As 
and the grommet. 
3.1 If the clearance is sufficient, proceed to step 4. 
3.2 If the clearance is not sufficient: 
3.2.1 Remove and discard the existing grommet. 
3.2.2 Inspect the indicated C/As for conditions and, in case of damage 
replace the interested C/As, in accordance with the instructions given 
in BHT-ELEC-SPM. 
3.2.3 With reference to Figure 4, rework the bulkhead in the emergency bus 
interlock compartment as follow: 
3.2.3.1 In accordance with the instructions given in BHT -ALL-SRM 
remove paint and primer in the area of reworking. 
3.2.3.2 Rework the lightening hole as indicated in Figure 4. 
3.2.3.3 Deburr the hole and break sharp edges with radius 0.13÷0.38 
mm.

### Page 6

S.B. N°412-160 
 DATE: August 13, 2020 
Page 6 of 11 REVISION: / 
3.2.3.4 In accordance with the instructions given in BHT -ALL-SRM 
apply chemical film protection to the reworked area. 
3.2.3.5 Prime all bare metal surfaces using epoxy polyamide primer 
and let dry. 
CAUTION 
Use of adhesive EC847/1236, or equivalent is mandatory. 
Pay particular attention during its application to ensure the 
correct installation of the grommet. 
3.2.4 With reference to Figure 5 and in accordance with the instructions 
given in BHT -ELEC-SPM, install grommet P/N MS21266 -1N with the 
junction in the upper part, using adhesive EC847/1236. Adapt the 
grommet dimension during installation. 
4. Return the helicopter to a ready to flight condition and record for compliance with this 
Service Bulletin on the helicopter logbook. 
5. Send the attached compliance form to the following mail box: 
 absereng.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
 Non cancellare mai questo segnalibro Non 
.interruzione sezione

### Page 7

Figure 1 
S.B. N°412-160 
DATE: August 13, 2020 
REVISION: / Page 7 of 11 
 
 
 
 
 
 
 
 
 
  
Grommet to be 
verified 
Emergency bus 
interlock 
compartment

### Page 8

Figure 2 
 S.B. N°412-160 
 DATE: August 13, 2020 
Page 8 of 11 REVISION: / 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Example of correct installation:  
sufficient clearance between the C/As and the grommet 
  
Grommet P/N 
MS35489-23

### Page 9

Figure 3 
S.B. N°412-160 
DATE: August 13, 2020 
REVISION: / Page 9 of 11 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Example of incorrect installation:  
insufficient clearance between the C/As and the grommet

### Page 10

Figure 4 
 S.B. N°412-160 
 DATE: August 13, 2020 
Page 10 of 11 REVISION: /

### Page 11

Figure 5 
S.B. N°412-160 
DATE: August 13, 2020 
REVISION: / Page 11 of 11

### Page 12

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
