# Agusta Service Bulletin 69-178: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0612, the docket of AD 2021-20-17. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Service Bulletin 69-178](https://openairdocs.org/service-documents/leonardo/sb-69-178.md)
- Title as filed: Leonardo Helicopters Emergency ASB No. 169-178
- Pages: 28
- PDF: https://openairdocs.org/files/sha256/09/d2/09d2e4129e9ebba5fb29fadf2b96cc6a148bf0932f94e3e5825bb7e8fa48baec
- Page: https://openairdocs.org/service-documents/leonardo/sb-69-178/file/09d2e4129e9e

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 1 69-178
DAT E:  August 4, 2020 
REV. :  / -  Ju ly 10, 2020 
Pag e 1 of 27 
TITLE 
ATA 64 - TR FLIGHT CONTROL PERIODICAL INSPECTION FOR IMPROVED DUPLEX 
BE
ARING 
REVISION LOG 
First issue. 
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
EMERGENCY ALERT
SERVICE BULLETIN

### Page 2

S.
B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
Page 2 of 27 REVISION: / 
1. PLANNING INFORMATION
A. EFFECTIVITY 
Part I: All AW 169 helicopters equipped with Tail Rotor Duplex Bearing 
P
/N MM6430V00151 and TRA P/N 6F6730V00331. 
Part II: All AW 169 helicopters equipped with Tail Rotor Duplex Bearing 
P/N MM6430V00151. 
Part III: All AW 169 helicopters equipped with Tail Rotor Duplex Bearing 
P/N MM6430V00151. 
Part IV: All AW 169 helicopters equipped with Tail Rotor Duplex Bearing 
P/N MM6430V00151. 
B. COMPLIANCE 
GENERAL NOTE 
A non-cumulative tolerance of 10% may be applied to 
the compliance times specified in this SB to allow 
synchronization of the required inspections with other 
required maintenance tasks for which a non-cumulative 
tolerance is already granted in the applicable 
Maintenance Manual. 
Part I:  
Within 10 FH from any installation of TR Duplex Bearing P/N MM6430V00151. Then 
repeat the inspection every 10 FH. 
NOTES 
• Every time it is required to perform Part II,
accomplishment of Part I on the same
maintenance downtime must be performed as a
prerequisite.
• If Part III is required in the same maintenance
downtime of Part II, it shall be performed lastly.
Part II:  
Within 50 FH from any installation of TR Duplex Bearing P/N MM6430V00151. Then 
repeat the inspection every 50 FH. 
Part III:  
Upon any installation of TR Duplex Bearing P/N MM6430V00151. Then repeat the 
inspection every 100 FH.

### Page 3

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 3 of 27 
NOTES 
• Perform in sequence Part I and Part II as a 
prerequisite. 
• If Part III is required in the same maintenance 
downtime of Part IV, it shall be performed after 
Part IV. 
• The operations performed in accordance with 
Part IV of this SB covers also the already 
approved AMPI Maintenance Task (i.e. MT 64-
07, required every 400 FH). 
Part IV:  
Within 100 FH from any installation of TR Duplex Bearing P/N MM6430V00151. Then 
repeat the inspection every 100 FH. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to require the periodical inspection of the 
slippage marking of the back-end castellated nut of the TR servo-actuator, the 
introduction of a new Thermal strip and the periodical detailed inspection of the new 
improved TR duplex bearing. 
E. DESCRIPTION 
Following the introduction on in-service fleet of the new improved TR Duplex Bearing 
P/N MM6430V00151, this Service Bulletin provides the instructions for the new 
inspection regime, partially requiring some of the checks already requested by SB 
169-148 on previous TR Duplex Bearing P/N 4F6430V00551. 
In details, Part I of this Service Bulletin provides the periodical detailed inspection of 
the slippage marking of the castellated nut installed on the back end of the TRA 
P/N 6F6730V00331, retaining the requirements of Part I of SB 169-148. 
Part II partially retains the requirement of the Parts II, IV and V of the SB 169-148, 
requiring the detailed inspection of TR duplex bearing, in addition to the verification of 
particle presence in the grease and the recursive check of the Thermal strip. 
Part III provides the instructions to install a new dedicated Thermal strip in the area of 
the TR duplex bearing.

### Page 4

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 4 of 27 REVISION: / 
Part IV partially retains the requirement of the Parts II and VI of the SB 169-148, 
requiring a check for axial play and a roughness check of the duplex bearing to be 
performed after removal of the spider assembly. 
Incorrect installation of the TR servo-actuator back-end nut or seizure of the TR 
Duplex bearing may lead to loss of Tail Rotor control which, depending on the flight 
condition, could lead to loss of control of the aircraft. 
Feedback on the compliance to this Service Bulletin is required. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
E.A.S.A. states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately half (0.5); 
Part II: approximately two (2); 
Part III: approximately one (1); 
Part IV: approximately three (3); 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A.

### Page 5

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 5 of 27 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 69-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
I, II, III, 
IV, V, VI 
DM02 69-A-06-40-00-00A-010A-A Access door provision  I, II 
DM03 69-A-64-31-01-00A-520A-A Pitch link - Remove procedure II 
DM04 69-A-64-21-05-00A-520A-A Lightning conductor jumper – 
Remove procedure 
II 
DM05 69-A-64-31-03-00A-520A-A Spider plug - Remove procedure II, III, IV, 
V, VI 
DM06 69-A-64-31-03-00A-720A-A Spider plug - Install procedure II, III, IV, 
V, VI 
DM07 69-A-64-31-02-00A-520A-A Scissors group – Remove 
procedure 
II 
DM08 69-A-64-31-07-00A-520A-A Boot - Remove procedure II 
DM09 69-A-64-31-04-00A-520A-A Sliding control assy – Remove 
procedure 
II, VI 
DM10 69-A-64-31-04-00A-720A-A Sliding control assy – Install 
procedure 
II, VI 
DM11 69-A-64-31-05-00A-520A-B Duplex bearing - Remove 
procedure 
II, IV, V, 
VI 
DM12 69-A-64-31-05-00A-720A-B Duplex bearing - Install procedure  II, IV, V, 
VI 
2) ACRONYMS 
SB Service Bulletin 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LHD Leonardo Spa Helicopters 
MMH Maintenance Man Hours 
SB Service Bulletin 
FH Flight Hours 
TR Tail Rotor 
TRA Tail Rotor Actuator 
3) ANNEX 
N.A.

### Page 6

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 6 of 27 REVISION: / 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 7

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 7 of 27 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL  NOTE LOG P/N 
1 M06SHA094D01R1  Thermal Strip 1 . (1)(2) - 
2 LAMHALPATCH01R1   Protective layer 1 . (1) - 
 
Refer also to AW169 IPD for the spares materials required to comply with the AMP 
DMs referenced in the accomplishment instructions. 
2) CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
3 TT-N-95-B / Code No. 531055030 Aliphatic Naphtha (C059) AR (3) II,III 
 
Refer to AW169 AMDI for the consumables required to comply with the AMP DMs 
referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
(1) This item, strictly required for Part III embodiment, may be required on condition 
also within the embodiment of other Parts of this SB. 
(2) Identification on label M06SHAL094D01R1 is printed on the thermal strip. 
(3) Item to be furnished as local supply. 
B. SPECIAL TOOLS 
Refer to ITEP for the special tools required to comply with the AMP DMs referenced in 
the accomplishment instructions. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
than the applicable date in the “Compliance” section will be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools.

### Page 8

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 8 of 27 REVISION: / 
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked from the aircraft has to be returned to LHD within thirty (30) calendar 
days after the shipment of the replacement part. In case of missing return within thirty 
(30) calendar days, Customer will be invoiced for the price of the replacement part.

### Page 9

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 9 of 27 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
PART I 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
NOTE 
Removal of access panels 470AT and 470BT can be 
avoided if visual access to the inspection area is 
available by other means. A suitable borescope can be 
used for this purpose. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A- A remove the access panels 
470AT and 470BT. 
3. Take a picture of the back-end area of the TRA clearly showing the slippage mark, and 
keep a record in a local archive to be made available if required. 
4. With reference to Figure 1, check the slippage mark on the castellated nut for absence 
of evidence of rotation between the parts. Record the result on Table I on Figure 5. 
5. If any evidence of rotation is found, contact the Product Support Engineering  
(engineering.support.lhd@leonardocompany.com) to receive further instructions before 
performing the following checks: 
5.1 Send the picture taken at step 3 to Product Support Engineering 
(engineering.support.lhd@leonardocompany.com). 
5.2 If the helicopter is already compliant with the SB 169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
5.3 Perform Thermal strip and TR Duplex bearing detailed inspection as per Part II of 
this SB; 
5.4 In case replacement of Duplex Bearing is confirmed as necessary, perform step 
6.3 of Part II of this SB. 
6. If no evidence of rotation is found in step 4, return the helicopter to a ready to flight 
condition and record for compliance with Part I of this Service Bulletin on the helicopter

### Page 10

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 10 of 27 REVISION: / 
logbook. 
7. Send the attached compliance form and the compiled Table I to the following mail box:  
engineering.support.lhd@leonardocompany.com  
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 11

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 11 of 27 
PART II 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
NOTE 
If not damaged, the O-ring removed in the following 
step can be retained for later reinstallation. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A- A, remove the spider plug. 
3. Perform the inspection of the Thermal Strip as detailed below: 
3.1 With reference to Figure 2, check the thermal strip and the protective layer for 
good adhesion and general condition, and the thermal strip only for readability; 
then proceed as follows: 
3.1.1 If the strip and/or the protective layer are detached, partially detached, 
damaged or unreadable, perform steps 3.1.2 thru 3.1.6, otherwise skip 
to step 3.2:  
3.1.2 perform the TR duplex bearing inspection in accordance with step 4; 
3.1.3 If helicopter is already compliant with the SB 169-140, perform HUMS 
data download from AMMC to DTD. Upload the HUMS data to Heliwise 
3.1.4 Contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to receive further 
instructions; 
3.1.5 Replace the thermal strip in accordance with the instructions reported 
in Part III of this SB; 
3.1.6 Skip to step 7. 
3.2 If any of the Thermal Strip cells appears coloured, provide a picture of the 
Thermal Strip to Product Support Engineering 
(engineering.support.lhd@leonardocompany.com), then proceed with the 
following step. 
3.3 With reference to Figure 5, check the temperature reached by the thermal strip 
installed on spacer P/N MM6430A00151. 
3.4 Record the check result on Table II (refer to Figure 6) and provide the Table and 
the Compliance Form to Product Support Engineering, as required by step 8. 
3.5 If temperature has reached a value equal to or above 104°C, proceed with steps 
3.5.1 thru 3.5.4, otherwise skip to step 4: 
3.5.1 perform the TR duplex bearing inspection in accordance with step 4 
thru step 5.

### Page 12

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 12 of 27 REVISION: / 
3.5.2 If the helicopter is already compliant with the SB 169-140, perform 
HUMS data download from AMMC to DTD. Upload the HUMS data to 
Heliwise. 
3.5.3 Contact immediately the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to receive further 
instruction before thermal strip and duplex bearing removal and 
replacement. 
3.5.4 In case replacement of Duplex Bearing is confirmed as necessary, 
perform steps 6.3 of Part II of this SB. 
4. Perform the inspection of the TR duplex bearing in accordance with the following 
procedure: 
4.1 Inspect the visible parts of the TR duplex bearing (including the seals) for 
absence of wear, damages and security of attachment. Record the results on 
Table II (refer to Figure 6). 
4.2 Check the visible part of the TR duplex bearing for particles absence. 
CAUTION 
Pay attention not to damage the thermal strip and the 
protective layer during the grease sampling from the 
bearing housing. 
4.3 If any grease leakage is present on the visible part of the TR Duplex Bearing 
and/or on the spider plug, confirm absence of any particles by finger touch. 
4.4 Perform grease inspection for magnetic/metallic particles as detailed below: 
4.4.1 Put a small quantity of grease using a small spatula in a transparent 
container and add a solvent (aliphatic naphtha). Then use a magnet on 
the bottom out side of the container to confirm absence of magnetic 
particles in the solution. 
4.4.2 Record the result on Table II (refer to Figure 6) and collect the grease 
leaked from the visible surface in a proper container. 
5. If none of the checks performed in steps 4.1 thru 4.4.1 fails, proceed as follows, 
otherwise skip to step 6: 
5.1 If helicopter is already compliant with the SB 169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
5.2 Skip to step 7. 
6. If any of the checks performed in steps 4.1 thru 4.4.1 fails, perform the following 
operations: 
6.1 If helicopter is already compliant with the SB 169-140, perform HUMS data

### Page 13

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 13 of 27 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
6.2 Contact immediately the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to receive further instructions. 
6.3 In case replacement of Duplex Bearing is confirmed as necessary, refer to the 
following procedure: 
6.3.1 In accordance with applicable steps of AMP DM 69-A-64-31-01-00A-
520A-A, temporarily detach the upper attachment of all the pitch links 
from the TR. 
6.3.2 In accordance with applicable steps of AMP DM 69-A-64-31-02-00A-
520A-A, disconnect the upper half scissors from the spider. 
6.3.3 In accordance with applicable steps of AMP DM 69-A-64-31-07-00A-
520A-A, disconnect and lower the boot from the spider. 
6.3.4 In accordance with AMP DM 69-A-64-21-05-00A-520A-A, disconnect 
the TR lightning conductor jumper. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. After removal mark “IN” on the 
inboard opposite face of the TR duplex bearing. Use 
an indelible pen. 
6.3.5 In accordance with AMP DM 69-A-64-31-05-00A-52 0A-B, remove the 
TR duplex bearing. 
6.3.6 Collect the grease leaked from the TR duplex bearing “IN” marked side 
in a container different from the one used before. 
6.3.7 Take a picture of both faces of the removed TR duplex bearing and 
send them to PSE ( engineering.support.lhd@leonardocompany.com) 
before returning the bearing. 
6.3.8 Clean by means of a soft lint-free cloth the housing of the TR duplex 
bearing, the rod visible part and the internal side of the spider plug. 
6.3.9 Immediately return (within 2 days) the removed TR duplex bearing and 
the collecting containers of the grease to Leonardo Helicopters. 
Contact the Product Support Engineering

### Page 14

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 14 of 27 REVISION: / 
(engineering.support.lhd@leonardocompany.com) to receive the 
proper instructions to return the removed component. 
CAUTION 
Duplex Bearing must be installed with a controlled 
orientation. 
6.3.10 In accordance with AMP DM 69-A-64-31-05-00A-7 20A-B, install a new 
TR duplex bearing, keeping the outer race outside marking properly 
readable while letting down in the slider/spider seat. Refer to Figure 4 
NOTE 
Spacer P/N MM6430A00151 already installed on 
helicopter can be kept in service, provided that no 
damage or wear is present on the component. 
6.3.11 In accordance with the instructions reported on Part III of SB 169-178, 
replace Thermal Strip and Adhesive Protective Layer currently installed 
on Spacer P/N MM6430A00151 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
In case during the installation of control rod nut, after 
several attempts with different nuts, the minimum 
required breakaway torque (as required by AMP DM 
69-A-64-31-04-00A-720A-A) is not reached, please 
contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to 
receive dedicated instructions. 
6.3.12 In accordance with AMP DM 69-A-64-31-04-00A-7 20A-A, restore 
Sliding Control Assy installation on the helicopter. 
6.3.13 With reference to Figure 1, restore the slippage marking on the 
castellated nut from the hinge bracket element to the rod. 
6.3.14 In accordance with AMP DM 69-A-64-31-01-00A-720A-A, restore the 
correct installation of TR pitch links.

### Page 15

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 15 of 27 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
7. In accordance with AMP DM 69-A-64-31-03-00A-720A- A, install the spider plug. 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
8. Send the attached compliance form and the compile d Table II to the following mail box: 
engineering.support.lhd@leonardocompany.com  
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
9. Return the helicopter to a ready to flight condition and record for compliance with Part II 
of this Service Bulletin on the helicopter logbook.

### Page 16

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 16 of 27 REVISION: / 
PART III 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A, remove the spider plug. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
3. In accordance with applicable steps of AMP DM 69- A-64-31-04-00A-520A-A, temporarily 
remove the spacer control rod P/N MM6430A00151 and the control rod nut. 
4. With reference to Figure 2, perform on an applicable workbench the installation of 
Thermal Strip and Adhesive protective layer as follows: 
4.1 With the use of a non-metallic spatula, remove the layer P/N 
LAMHALPATCH01R1 (if present) from the spacer. 
4.2 With the use of a non-metallic spatula, remove the installed thermal strip from the 
spacer 
4.3 Clean the spacer surface with a soft lint-free cloth soaked with a small quantity of 
aliphatic naphtha; then dry the surface with a clean cloth; make sure that no 
traces of grease / oil / dirt remained; 
CAUTION 
When installing the thermal strip pay attention to: 
• ensure a good adhesion with the spacer control 
rod P/N MM6430A00151; 
• Thermal Strip Celsius scale shall be kept on the 
outer side to ensure good readability when the 
spacer is installed. 
4.4 Install the thermal strip P/N M06SHA094D01R1 on the control rod spacer P/N 
MM6430A00151, paying particular attention to minimize formation of wrinkles; 
ensure a good adhesion with the spacer; 
4.5 Protect the thermal strip with the layer P/N LAMHALPATCH01R1, paying 
particular attention to minimize formation of wrinkles; 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.

### Page 17

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 17 of 27 
NOTE 
In case during the installation of control rod nut, after 
several attempts with different nuts, the minimum 
required breakaway torque (as required by AMP DM 
69-A-64-31-04-00A-720A-A) is not reached, please 
contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to 
receive dedicated instructions.. 
5. In accordance with applicable steps of AMP DM 69- A-64-31-04-00A-720A-A, reinstall 
the spacer control rod P/N MM6430A00151 and the control rod nut. 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
6. In accordance with AMP DM 69-A-64-31-03-00A-720A- A, install the spider plug. 
7. Return the helicopter to a ready to flight condition and record for compliance with Part III 
of this Service Bulletin on the helicopter logbook. 
8. Send the attached compliance form to the following mail box:  
engineering.support.lhd@leonardocompany.com  
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 18

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 18 of 27 REVISION: / 
PART IV 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A, remove the spider plug. 
3. In accordance with applicable steps of AMP DM 69-A-64-31-01-00A-520A-A, temporarily 
detach the upper attachment of all the pitch links from the TR. 
4. In accordance with applicable steps of AMP DM 69-A-64-31-02-00A-520A-A, disconnect 
the upper half scissors from the spider. 
5. In accordance with applicable steps of AMP DM 69-A-64-31-07-00A-520A-A, disconnect 
and lower the boot from the spider. 
6. In accordance with AMP DM 69-A-64-21-05-00A-520A-A, disconnect the TR lightning 
conductor jumper. 
7. Check for absence of axial play when trying to move the spider along the control rod 
axis. Record the result on Table III (refer to Figure 7). 
8. If axial play is detected, perform the following instructions, otherwise skip to step 9: 
8.1 If the helicopter is already compliant with the SB 169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
8.2 Contact immediately the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to receive further instruction 
before thermal strip and duplex bearing removal and replacement. 
8.3 In case replacement of Duplex Bearing is confirmed as necessary, perform step 
6.3 of Part II of this SB. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
9. In accordance with AMP DM 69-A-64-31-04-00A-520A- A, remove the sliding control 
assembly. 
10. With reference to Figure 3 lock the slider of the sliding control assembly in a bench vice 
with padded jaws. 
11. Examine the duplex bearing to find roughness in accordance with the following 
procedure:

### Page 19

S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: / Page 19 of 27 
NOTE 
• To initiate rotation of the duplex bearing, a 
break-out force could be necessary. The break-
out force is not an indication of roughness.  
• Relative axial movement between the inner 
races is acceptable and shall not be considered 
as a finding. 
11.1 Use your fingers to push down on the upper face  of the inner race of the duplex 
bearing. 
NOTE 
Do not release pressure, continue to apply pressure 
with your fingers during the subsequent step.  
11.2 With reference to Figure 3 section A-A Step 1, push the top inner race down and 
at the same time turn it to feel if there is roughness. 
11.3 Put your finger into the duplex bearing until you can pull up the lower face of the 
inner race.  
NOTE 
Do not release pressure, continue to apply pressure 
with your finger during the subsequent step.  
11.4 With reference to Figure 3 section A-A Step 2, pull the bottom inner race in the 
up direction and at the same time turn it to feel if there is roughness.  
11.5 Repeat the Step 11.1 thru Step 11.4 at least one time to confirm the results. 
11.6 Record the results of the previous steps on Table III (refer to Figure 7). 
12. If any of the checks performed in steps 11 thru 11.6 fails, perform the following 
operations, otherwise skip to step 13 
12.1 If helicopter is already compliant with the SB 169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
12.2 Contact immediately the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to receive further instructions. 
12.3 In case replacement of Duplex Bearing is confirmed as necessary, perform step 
6.3 of Part II of this SB. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.

### Page 20

S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 20 of 27 REVISION: / 
NOTE 
In case during the installation of control rod nut, after 
several attempts with different nuts, the minimum 
required breakaway torque (as required by AMP DM 
69-A-64-31-04-00A-720A-A) is not reached, please 
contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to 
receive dedicated instructions. 
13. In accordance with AMP DM 69-A-64-31-04-00A-720A -A, restore Sliding Control Assy 
installation on the helicopter. 
14. With reference to Figure 1, restore the slippage marking on the castellated nut from the 
hinge bracket element to the rod. 
15. In accordance with AMP DM 69-A-64-31-01-00A-720A-A, restore the correct installation 
of TR pitch links. 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
16. In accordance with AMP DM 69-A-64-31-03-00A-720A -A, install the spider plug. 
17. Return the helicopter to a ready to flight condition and record for compliance with Part IV 
of this Service Bulletin on the helicopter logbook. 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
18. Send the attached compliance form and the compil ed Table III to the following mail box: 
e
ngineering.support.lhd@leonardocompany.com  
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 21

Figure 1 
S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: /July 10, 2020 P age 21 of 27

### Page 22

Figure 2 
 S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 22 of 27 REVISION: / 
  
THERMAL STRIP
(FOR REFERENCE ONLY)
SB189-272-002-01
INSTALL:
THERMAL STRIP ON
INDICATED SPACER
˚C
˚F
99
210
94
201
104
219
110
230
115
239
120
248
INSTALL:
THERMAL STRIP
MM6430A00151
SPACER
SB169-178-001-01
MM6430A00151
SPACER

### Page 23

Figure 3 
S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: /July 10, 2020 P age 23 of 27 
 
 
MM6430V00151
TAIL ROTOR DUPLEX BEARING
SB169-178-002-01
A
A
6F6430A01232
SLIDING CONTROL ASSEMBLY
MM6430V00151
TAIL ROTOR DUPLEX BEARING
SECTION A-A
STEP 1
SECTION A-A
STEP 2

### Page 24

Figure 4 
 S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 24 of 27 REVISION: / 
 
 
SB169-178-003-01
6F6430A01232 SLIDING CONTROL ASSEMBLY
MM6430V00151 TAIL ROTOR DUPLEX BEARING

### Page 25

Figure 5 
S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: /July 10, 2020 P age 25 of 27 
TABLE I 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 6F6730V00331 
TRA S/N  
 
A/C FH at SB 
COMPLIANCE DATE:  
TRA FH at SB 
COMPLIANCE DATE  A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
 
ACTION Required Obtained 
PART I 
CASTELLATED NUT 
paint mark check 
NO ROTATION BETWEEN 
PARTS

### Page 26

Figure 6 
 S.B. N°169-178 EMERGENCY ALERT 
 DATE: August 4, 2020 
Page 26 of 27 REVISION: / 
TABLE II 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N MM6430V00151 
TR DUPLEX 
BEARING S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX 
BEARING FH at SB 
COMPLIANCE DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
 
ACTION Required Obtained 
PART II 
THERMAL STRIP 
General condition check 
GOOD ADHESION AND 
READABILITY. NO DAMAGE.  
THERMAL STRIP 
Temperature check  RECORDED TEMPERATURE  
THERMAL STRIP 
Temperature check 
TEMPERATURE SHALL NOT 
REACH A VALUE EQUAL TO OR 
ABOVE 104°C. 
 
TR DUPLEX BEARING 
wear and damages check NO FINDINGS  
TR DUPLEX BEARING 
Particles check 
ABSENCE of ANY 
PARTICLES  
TR DUPLEX BEARING 
Grease leakage check 
ABSENCE of METALLIC 
PARTICLES

### Page 27

Figure 7 
S.B. N°169-178 EMERGENCY ALERT 
DATE: August 4, 2020 
REVISION: /July 10, 2020 P age 27 of 27 
TABLE III 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N MM6430V00151 
TR DUPLEX 
BEARING S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX 
BEARING FH at SB 
COMPLIANCE DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
 
ACTION Required Obtained 
PART IV 
TR SPIDER 
axial play check 
ABSENCE of  
AXIAL PLAY  
TR DUPLEX BEARING 
Roughness check by fingers FREE AND EASY ROTATION

### Page 28

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
