# Lockheed Alert Service Bulletin A382-57-99: Revision 1

- Rights: © LOCKHEED MARTIN CORPORATION. Filed by the FAA in regulations.gov docket FAA-2021-0341; AD 2021-09-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lockheed Alert Service Bulletin A382-57-99](https://openairdocs.org/service-documents/lockheed/a382-57-99.md)
- Title as filed: A382-57-99 R1
- Pages: 21
- PDF: https://openairdocs.org/files/sha256/c4/68/c4688ca4a3284a2e415e6ac6abc3394aef2724cd06999455a4c153276a587dc5
- Page: https://openairdocs.org/service-documents/lockheed/a382-57-99/file/c4688ca4a328

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
Revision 1, February 17, 2021 A382-57-99
THIS DOCUMENT CONTAINS COMMERCIAL PROPRIETARY TECHNICAL DATA OF LOCKHEED MARTIN CORPORATION AND OTHERS. USE, COPYING AND/OR DISCLOSURE OF THE TECHNICAL DATA CONTAINED HEREIN IS GOVERNED BY THE TERMS OF LOCKHEED MARTIN
CORPORATION'S L-100 SALES CONTRACT WITH THE CUSTOMER.
© 2021 LOCKHEED MARTIN CORPORATION. 
EXPORT CONTROLLED INFORMATION
WARNING - This document contains data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) as 
amended, or the Export Administration Act (Title 50, U.S.C., App 2401 et seq.) as amended. Violations of these export laws are subject to 
severe criminal and civil penalties.
*REVISION NOTICE*
WING - INSPECTION OF CENTER WING FORWARD CORNER FITTINGS, CENTER/OUTER WING CORNER 
FITTING FASTENERS, AND RETORQUE OF WING JOINT FRONT BEAM WEB SPLICE BOLTS
Attached is Revision 1, dated February 17, 2021, to Service Bulletin A382-57-99. Information added or changed in this 
issue is indicated by a vertical revision bar in the margin of affected pages, or pointing hand for illustrations.
This revision updates Section 1, Paragraph G: Section 2, Accomplishment Instructions, and replaces the artwork for 
Figure 1, Sheet 2.
This revision is a complete reissue and replaces the basic issue of this Service Bulletin dated February 12, 2021. 
Retain this notice with your copy of this Service Bulletin.
Aircraft modified by the basic issue of this Service Bulletin will require rework.
List of Previous Revisions and/or Reissues
__________#__________
File: I-5137R1
Basic February 12, 2021

### Page 2

(No text on this page.)

### Page 3

HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
Page 1 of 19
A382-57-99
THIS DOCUMENT CONTAINS COMMERCIAL PROPRIETARY TECHNICAL DATA OF LOCKHEED MARTIN CORPORATION AND OTHERS. USE, COPYING AND/OR DISCLOSURE OF THE TECHNICAL DATA CONTAINED HEREIN IS GOVERNED BY THE TERMS OF LOCKHEED MARTIN
CORPORATION'S L-100 SALES CONTRACT WITH THE CUSTOMER. 
© 2021 LOCKHEED MARTIN CORPORATION. 
EXPORT CONTROLLED INFORMATION
WARNING - This document contains data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) as 
amended, or the Export Administration Act (Title 50, U.S.C., App 2401 et seq.) as amended. Violations of these export laws are subject to 
severe criminal and civil penalties.
February 12, 2021
Revision 1, February 17, 2021
WING - INSPECTION OF CENTER WING FORWARD CORNER FITTINGS, CENTER/OUTER WING CORNER 
FITTING FASTENERS, AND RETORQUE OF WING JOINT FRONT BEAM WEB SPLICE BOLTS
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) This Service Bulletin is app licable to all model 382, 382B, 382E, 382F, and 382G FAA Certificated 
Hercules aircraft (excluding 382J series aircraft).
(2) Spares - This Service Bulle tin is not applicable to spares.
B. REASON
(1) The purpose of this Alert Ser vice Bulletin is to inspect the left and right center wing upper and lower 
forward corner fittings for cracking, to check for sheared fasteners in the center and outer wing upper 
and lower forward corner fitting attachments, and to retorque the fasteners in the outer wing to center 
wing beam web splice angles. This inspection is being accomplished because a crack was found 
in-service on the web attachment flange of the center wing upper forward corner fitting. Loose fasteners 
in the WS 220 wing joint at the front beam web can cause internal load redistribution resulting in 
cracked center wing upper and lower corner fittings and failed fasteners in the center and outer wing 
upper and lower corner fittings.
(2) Lockheed Martin Aeronautics Company recommends that the wing  joint front beam web fastener 
retorque specified herein be accomplished on all aircraft with less than 2,500 Flight Hours. The fastener 
retorque should be performed at the next scheduled maintenance after receipt of this Alert Service 
Bulletin but not to exceed 270 days.
(3) Lockheed Martin Aeronautics Company recommends that the corn er fitting inspection and wing joint 
front beam web fastener retorque specified herein be accomplished on all aircraft that have 
accumulated more than 2,500 Flight Hours. The inspection and fastener retorque should be performed 
within 90 days after receipt of this Alert Service Bulletin.
C. DESCRIPTION
An eddy current surface scan inspection will be performed on the center wing upper and lower forward 
corner fittings. An inspection and check torque will be performed on the left and right center and outer wing 
upper and lower forward corner fitting fasteners. The outer wing to center wing joint front beam web splice 
angle NAS6205 bolts will be retorqued to a higher torque value to prevent loosening of fasteners in service.
D. APPROVAL
(1) The aircraft owner /operator will make an appropriate entry in the aircraft log records upon compliance 
with this Service Bulletin.

### Page 4

Page 2 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT. February 12, 2021
Revision 1, February 17, 2021
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99
(2) After the work has been completed on each affected aircraft,  please complete and e-mail a Notice of 
Service Bulletin Compliance to hercules.support@lmco.com; or notify Lockheed Martin Aeronautics 
Company of compliance with this Service Bulletin at website address: 
http://www.lockheedmartin.com/csc and log into Data Library.
E. MANPOWER
The manpower estimates provided have not been validated and are estimates only. These estimates are 
provided only as a convenience for aircraft owner/operator planning purposes. It is estimated that 
approximately 40 man-hours (a crew of two qualified technicians) will be required to accomplish the work 
described herein on each affected aircraft. This will take approximately 20 hours elapsed time while the 
aircraft is out of service.
NOTE: This Service Bulletin is based upon the configuration of the aircraft as it was delivered from 
Lockheed Martin Aeronautics Company. Previous service bulletins issued by Lockheed Martin 
Aeronautics Company have been considered in the preparation of this Service Bulletin, but no 
consideration has been given to peculiar changes made to the aircraft by the owner/operator 
since its delivery.
F. MATERIAL - COST AND AVAILABILITY
None.
G. TOOLING - PRIC E AND AVAILABILITY
(1) Eddy Current Unit, Nortec, 16- pin LEMO cable connector, Models 2000D/2000D+, or equivalent.
(2) Straight probe, shielded, 1/8  inch diameter, 1/2-inch drop, frequency to include 200kHz, 
VM Products P/N VM202RAF-6, or equivalent.
(3) Probe, straight, shielded, 1/ 16 inch diameter, frequency to include 200kHz, VM Products P/N 
VM200-.063 X 4, or equivalent.
(4) Probe, straight, shielded, 1/8  inch diameter, frequency to include 200 kHz, VM Products P/N 
VM200F-4, or equivalent.
(5) Cable, 6 foot, VM Products, P/N  VM99L16/M-NR, or equivalent.
(6) Standard, aluminum, VM Products, P/N VM30889-C1A, or equival ent.
H. WEIGHT AND BALANCE
None.
I. REFERENCES
Hercules Maintenance Manual
Hercules Structural Repair Manual
SMP 515-C
SP-163
TO 1C-130A-36

### Page 5

Page 3
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99February 12, 2021
Revision 1, February 17, 2021
J. OTHER PUBLICATIONS AFFECTED
Aircraft Scheduled Inspection and Maintenance Requirements

### Page 6

Page 4 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT. February 12, 2021
Revision 1, February 17, 2021
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99
THIS PAGE INTENTIONALLY LEFT BLANK.

### Page 7

Page 5
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99February 12, 2021
Revision 1, February 17, 2021
2. ACCOMPLISHMENT INSTRUCTIONS
WARNING: OBSERVE ALL APPLICABLE SAFETY PRECAUTIONS WHILE ACCOMPLISHING THIS 
INSPECTION. ENSURE THAT ALL ELECTRICAL AND HYDRAULIC POWER SOURCES ARE 
OFF, THE BATTERY AND EXTERNAL ELECTRICAL POWER DISCONNECTED, AND 
HYDRAULIC SYSTEMS DEPRESSURIZED BEFORE STARTING THE WORK. FAILURE TO 
COMPLY MAY RESULT IN SERIOUS INJURY OR DEATH. 
NOTE: Center wing corner fitting inspections are based on the existing procedures described in the SMP 515-C, 
SP-163 or TO 1C-130A-36.
A. Prepare aircraft for inspection and/or modification as follow s:
(1) RC - Remove electrical powe r from aircraft. Refer to applicable Hercules Maintenance Manual .
(2) RC - Remove the hydraulic and fuel equipment dry bay and tan k access doors number (133/134) from 
the upper surface of the center wing behind engines No. 2 and 3. Refer to applicable Hercules 
Maintenance Manual.
WARNING: DO NOT ENTER FUEL AREAS UNLESS FUEL VAPOR CONTENT IS 0.0 PERCENT LOWER 
EXPLOSIVE LIMIT (LEL) (NO RESPIRATOR PROTECTION REQUIRED) WITH AN OXYGEN 
CONCENTRATION NOT LESS THAN 19.5 PERCENT. PROVIDE CONTINUOUS VENTILATION IN 
THE FUEL AREA THROUGHOUT THIS PROCEDURE.
(3) RC - Depuddle, as required, a nd purge the dry bay areas. Refer to applicable Hercules Maintenance 
Manual  to the 0.0 percent LEL and 19.5 percent oxygen content.
(4) Open and lock the nacelle acc ess panels (299/300) behind Engines No. 2 and 3 to gain access to the 
inspection areas on the forward side of the upper forward corner fitting. Refer to applicable Hercules 
Maintenance Manual.
(5) Remove the leading edges immediately outboard of the No. 2 a nd No. 3 engine nacelles for access to 
the front beam at the OWS 0 to 20 location. Refer to applicable Hercules Maintenance Manual. 
(6) Remove Nacelle access panel number 36 on the outboard sides of Engines No. 2 and 3 to gain access 
to retorque the wing joint front beam web splice bolts at WS 220. Refer to applicable Hercules 
Maintenance Manual.
(7) Brush or wipe all loose dirt  and debris from the inspection areas.
CAUTION: DO NOT USE METALLIC TOOLS TO REMOVE SEALANT. EQUIPMENT DAMAGE COULD 
OCCUR.
(8) Remove sealant from the ins pection area using a non-metallic scraper. Metallic tools shall not be used 
to remove sealant.
WARNING: ISOPROPYL ALCOHOL AND CLEANING COMPOUND ARE FLAMMABLE AND TOXIC TO EYES, 
SKIN AND RESPIRATORY TRACT. SKIN AND EYE PROTECTION IS REQUIRED. GOOD 
GENERAL VENTILATION IS NORMALLY ADEQUATE. AVOID ALL SOURCES OF IGNITION.
(9) Remove oil, grease and resid ual sealant by wiping area with clean rags wet with ASTM D 770 
Isopropyl Alcohol or MIL-PRF-87937 Cleaning Compound. Residual thin films of sealant may take 
several applications of solvent, scraping and wiping to be completely removed.
(10) Remove any flaking and/or loose paint from the inspection areas.

### Page 8

Page 6 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT. February 12, 2021
Revision 1, February 17, 2021
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99
B. Inspection Procedures:
(1) Calibration
(a) Use the following NDI Equipment:
1 Eddy Current Unit, Nortec, 16-pin LEMO cable connector, Models 2000D/2000D+, or 
equivalent.
2 Probe, right angle, shielded, 1/8 inch diameter, 1/4-inch drop, frequency to include 
200kHz, VM Products P/N VM202RAF-6, or equivalent.
3 Probe, straight, shielded, 1/16 inch diameter, frequency to include 200kHz, VM Products 
P/N VM200-.063 X 4, or equivalent.
4 Probe, straight, shielded, 1/8 inch diameter, frequency to include 200 kHz, VM Products 
P/N VM200F-4, or equivalent.
5 Cable, 6 foot, VM Products, P/N VM99L16/M-NR, or equivalent.
6 Standard, aluminum, VM Products, P/N VM30889-C1A, or equivalent.
(b) Nortec 2000D or 2000S Equipment Preparation:
1 Connect probe and cable to the instrument. Probe and cable shall connect directly to the 
16-pin LEMO connector on the Nortec 2000D or 2000S. Use of any adapters to mate 
with other types of probes is prohibited without authorization.
2 Connect eddy current unit to power source, if necessary.
3 Refer to manufacturer's instrument manual for all operating instructions.
4 The part to be inspected, calibration standard, inspection unit and probe must be at 
ambient temperature to assure that valid test data is obtained.
5 Adjust initial equipment settings as follows:
NOTE: Minor adjustments to these settings are allowable to achieve optimum signal characteristics.
a On main menu, set FREQUENCY 1 to 200 KHZ, set FREQUENCY 2 to OFF 
(not applicable to the Nortec 2000S), set HORIZONTAL GAIN to 65.0 dB, set 
VERTICAL GAIN to 75.0 dB, and set ANGLE to 70 degrees.
b On filter menu, set LP FILTER to 100 Hz, set HP FILTER to OFF, and set CONT 
NULL to OFF.
c On display menu, set SWEEP to OFF, Set V-POS to 10%, and set H-POS to 
80%.
d On screen menu, set PERSIST to OFF, set DISP ERASE to 3.0 S, set 
GRATICULE to ON, set DOT/BOX to ON, and set SWEEP to OFF.
e On setup menu, set FREQ to SINGLE, and PRB DRV to MID.

### Page 9

Page 7
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99February 12, 2021
Revision 1, February 17, 2021
6 Equipment calibration: Place probe on the calibration standard surface so the coil is a 
minimum of twice the probe diameter from all notches and edges. Press the NULL key. 
Hold the probe still until NULLING is complete. Press the ERASE key.
NOTE: Periodic erasing may be required.
7 While lifting the probe on and off the calibration standard, adjust ANGLE until a 
substantially horizontal, right to left, lift-off signal is achieved.
8 Repeatedly scan across the 0.020 inch deep notch in the calibration standard. Adjust 
H-GAIN and V-GAIN until a signal trace of 80% vertical deflection is obtained from the 
0.020 inch notch.
9 Check lift-off and notch indication to ensure that the signals are similar to those shown in 
Figure 4.
10 Recalibration of the eddy current instrument and probe shall be accomplished when one 
of the following occurs:
a Immediately prior to a series of examinations/scans.
b After any interruption in system continuity such as power interruptions, 
instrument or probe change-outs, activation of new examination/scan setups, 
change in examination personnel, etc.
c At any instance of suspected system irregularity.
(2) RC - Inspection
(a) Left and right center wing upper forward corner fittings.
1 Scan the exterior of the vertical flange of the corner fitting common to the front beam 
web. Scan in the directions as shown. Pay particular attention for fatigue cracking 
initiating at the web attachment fasteners or from the flange inboard radius propagating 
spanwise above the web attachment fasteners. See Figure 1, Sheet 2, View B.
2 Torque the nine identified fasteners. Refer to applicable Hercules Structural Repair 
Manual. See Figure 1, Sheet 2, View B. When torquing the hi-tigue fasteners common to 
the corner fitting to check security/looseness do not use the allen-hex wrench to secure 
the pin and apply only the lower end torque value specified in the applicable Hercules 
Structural Repair Manual. Check for loose, pulled, or broken fasteners. 
(b) Left and right center wing lower forward corner fittings.
1 Scan the interior surfaces of the corner fitting horizontal and vertical flanges common to 
the beam cap following the procedures listed in SMP 515-C, SP-163 or TO 1C-130A-36. 
See Figure 1, Sheet 3, View C.
2 Torque the nine identified fasteners. Refer to applicable Hercules Structural Repair 
Manual. See Figure 1, Sheet 3, View C. When torquing the hi-tigue fasteners common to 
the corner fitting to check security/looseness do not use the allen-hex wrench to secure 
the pin and apply only the lower end torque value specified in the applicable Hercules 
Structural Repair Manual. Check for loose, pulled, or broken fasteners.

### Page 10

Page 8 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT. February 12, 2021
Revision 1, February 17, 2021
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99
(c) Left and right outer wi ng forward corner fittings.
CAUTION: DO NOT REMOVE ANY OF THE 23 FASTENERS IDENTIFIED IN STEP 2.B.(2)(c)1 WITHOUT 
DEFUELING THE AFFECTED TANK. FAILURE TO DO SO COULD CAUSE AIRCRAFT DAMAGE.
NOTE: The 23 fasteners identified in Step 2.B.(2)(c)1 are common to the fuel tank.
1 Torque the 23 identified fasteners. Refer to applicable Hercules Structural Repair 
Manual. See Figure 2, Sheet 2, Views B and C. When torquing the hi-tigue fasteners 
common to the corner fitting to check security/looseness do not use the allen-hex 
wrench to secure the pin and apply only the lower end torque value specified in the 
applicable Hercules Structural Repair Manual. Check for loose, pulled, or broken 
fasteners. 
(d) Left and right outer wing to center wing beam web joint spli ce angle fasteners
1 Record the existing torque values of the seventeen fasteners (left and right) in the 
provided table by noting the torque when the nuts first begin to turn. See Figure 3, 
Sheet 2, View B.
WARNING: TORQUE STRIPE AND SEALANT ARE FLAMMABLE AND TOXIC TO EYES, SKIN AND 
RESPIRATORY TRACT. SKIN AND EYE PROTECTION IS REQUIRED. GOOD GENERAL 
VENTILATION IS NORMALLY ADEQUATE. AVOID ALL SOURCES OF IGNITION.
2 Retorque the 17 (left and right) NAS6205/KFN542 bolts and nuts to 220 to 240 in-lbs. 
The fasteners are to be torqued from the nut side holding the bolt from turning with a 
socket/wrench. Touch up sealant overcoat on bolts/nuts electrically bonded using 
MIL-PRF-81733 Class I, Grade A Sealant. Apply EC1252 Torque Stripe Paint to the bolt 
head and to the nut, after the sealant is tack free, in accordanceapplicable Hercules 
Maintenance Manual when completed. See Figure 3, Sheet 2, View B.
C. RC - Acceptance Criteria
(1) Mark and Report Damage:
(a) Report any damage detected by this inspection procedure, as well as the recorded torque 
values on the wing joint front beam web splice bolts to Lockheed Martin Aeronautics Company. 
Provide the following information as applicable for damage detected and torque data:
1 Aircraft Serial Number
2 Aircraft Flight Hours
3 Location and description
4 Length, depth, and orientation of crack
(2) Aircraft with detected fatigue cracks in the center wing upp er or lower forward corner fittings should not 
be operated, contact Lockheed Martin Aeronautics for technical assistance. Sheared or missing 
fasteners are to be replaced before returning the aircraft to service.

### Page 11

Page 9
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99February 12, 2021
Revision 1, February 17, 2021
D. RC - Restore aircraft to service:
(1) Clean inspection area and res tore any finishes removed. Reinstall any removed components and 
structure. Perform Ops Check following reinstallation of the wing leading edges per the Hercules 
Maintenance Manual. Remove maintenance and inspection equipment and supplies from the 
inspection area.
(2) Perform operation check of disturbed systems in accordance w ith applicable aircraft manuals. 
Functional check flight is not required after inspection.
(3) The aircraft owner/operator shall make an appropriate entry in the aircraft log records upon compliance 
with this Service Bulletin.
(4) After the work has been completed on each affected aircraft,  please complete and mail or fax 
(770-494-5682) a Notice of Service Bulletin Compliance; or notify Lockheed Martin Aeronautics 
Company of compliance with this Service Bulletin at website address: www.lockheedmartin.com/ams 
and log into Data Library.
(5) If all inspection results are  acceptable and no further inspection is required, return aircraft to service. 
For any inspection results out of limits, Lockheed Martin Aeronautics Company must review results to 
determine further actions. Submit all inspection results (passing and failing) to Lockheed Martin 
Aeronautics Company at hercules.support@lmco.com.
NOTE: If assistance is needed, contact your local Lockheed Martin Aeronautics Company representative, or the 
Customer Support Center in Marietta, Georgia, USA, as follows:
TELEPHONE: (770) 494-9131
FAX: (770) 494-9122
E-MAIL: hercules.support@lmco.com
MAIL: Lockheed Martin Aeronautics Company
86 South Cobb Drive
Dept. 3D3M00, Zone 0591
Marietta, GA 30063, USA

### Page 12 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
CWS 220
UPPER FORWARD
CORNER FITTING
FS 517.
VIEW A
VIEW LOOKING DOWN AND INBOARD AT
THE CENTER WING, CWS 220
(LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE
C
LOWER FORWARD
CORNER FITTING
1-5139-001
Inspection of Center Wing Upper and Lower Forward Corner Fittings
Figure 1, Sheet 1 of 3
A382-57-99  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  February 12, 2021
Page 10  Revision 1, February 17, 2021

### Page 13 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
EXPECTED CRACK
ORIENTATION AT CORNER
UPPER FORWARD  CORNER FITTING  FITTING FILLET RADIUS
CWS 210  CWS 214  CWS 218  CWS 220
FS 517
STIFFENER  THICKNESS  FILLET RADIUS
ENGINE TRUSS  TRANSITION  RADIUS  EXPECTED CRACK  ORIENTATIONS (TYPICAL  FIRESEAL RIB
UP  MOUNT  FOR ALL FASTENERS)  ATTACH ANGLE
VIEW LOOKING AFT AT THE UPPER
INBD  FORWARD CORNER FITTING, FS 517
(LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE)
• OUTBD
INCLUDES THIS
FASTENER AND
ADJACENT
INBOARD
FASTENER
OUTBD
SURFACE EDDY CURRENT SCAN THE VERTICAL FLANGE OF THE CORNER FITTING AS SHOWN
LOOKING FOR CRACKING INITIATING AT THE FASTENERS AND FROM FLANGE RADIUS.
FASTENERS INDICATED TO BE TORQUED IN ACCORDANCE WITH STEP 2.B.(2). (a).
VIEW
Inspection of Center Wing Upper and Lower Forward Corner Fittings
Figure 1, Sheet 2
February 12, 2021  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  A382-57-99
Revision 1, February 17, 2021  Page 11

### Page 14 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
FRONT
BEAM WEB
(LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE)
EXPECTED CRACK
ORIENTATION
(TYPICAL)
FS 517
FWD
a
LOWER FORWARD  EXPECTED CRACK
CWS 220  CORNER FITTING  ORIENTATION (TYPICAL)  OUTBO
OUTBD
SURFACE EDDY CURRENT SCAN THE CORNER FITTING FLANGES AS SHOWN LOOKING
FOR CRACKING INITIATING AT FASTENER HOLES
FASTENERS INDICATED TO BE TORQUED IN ACCORDANCE WITH STEP 2.B. (2). (b).
VIEW C
Inspection of Center Wing Upper and Lower Forward Corner Fittings
Figure 1, Sheet 3
A382-57-99  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  February 12, 2021
Page 12  Revision 1, February 17, 2021

### Page 15 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
OUTER WING
FRONT BEAM
OWS 0
OUTED
ENGINE NO. 2
NACELLE
VIEW A
VIEW LOOKING AFT AT THE OUTER WING
FRONT BEAM, OWS 0
LEADING EDGE, SUPPORT BRACKETS, PLUMBING
AND WIRING REMOVED FOR CLARITY
(LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE)
1-5139-004
Inspection of Outer Wing Upper and Lower Forward Corner Fitting Fasteners
Figure 2, Sheet 1 of 2
February 12, 2021  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  A382-57-99
Revision 1, February 17, 2021  Page 13

### Page 16 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
• UP
OUTBD
FASTENERS INDICATED TO BE TORQUED IN ACCORDANCE WITH STEP 2.B. (2). (C).
VIEW
UP
OUTBD
FASTENERS INDICATED TO BE TORQUED IN ACCORDANCE WITH STEP 2.B.(2). (c).
VIEW
Inspection of Outer Wing Upper and Lower Forward Corner Fitting Fasteners
Figure 2, Sheet 2
A382-57-99  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  February 12, 2021
Page 14  Revision 1, February 17, 2021

### Page 17 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
VIEW LOOKING INBOARD AND AFT
LEFT WING SHOWN, RIGHT WING SIMILAR
VIEW A
Retorque Outer Wing to Center Wing Beam Splice Angle Fasteners
Figure 3, Sheet 1 of 2
February 12, 2021  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  A382-57-99
Revision 1, February 17, 2021  Page 15

### Page 18 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
Existing Torque
Fastener  (in-Ib)
LHS  RHS
3
5
6
7
8
9
10
11
12
13
14
15
16
17
VIEW LOOKING INBOARDS AT FRONT BEAM
LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE
VIEW
Retorque Outer Wing to Center Wing Beam Splice Angle Fasteners
Figure 3, Sheet 2
A382-57-99  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  February 12, 2021
Page 16  Revision 1, February 17, 2021

### Page 19 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
ALERT SERVICE BULLETIN
- 60% FSW (MIN)
100% VSH
*' 0.020-INCH DEEP "  EDM NOTCH  50% VSH  80%  FSH
NULL
LIFT OFF  ** POINT
0% VSH
0% HSW  50% HSW  100% HSW
SIGNAL RESPONSE FROM 0.020-INCH DEEP EDM NOTCH
(ALUMINUM, WEAKLY/NON-FERROMAGNETIC ALLOYS)
0.020-INCH DEEP
EDM NOTCH
0.010-INCH DÈEP
EDM NOTCH
0.006-INCH DEEP
... EDM NOTCH
SIGNAL RESPONSES FROM 0.005, 0.010, AND 0.020-INCH DEEP EDM NOTCHES
(ALUMINUM, WEAKLY/NON-FERROMAGNETIC ALLOYS)
1-5139-008
Typical Screen Presentations for Equipment Calibration
Figure 4
February 12, 2021  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.  A382-57-99
Revision 1, February 17, 2021  Page 17

### Page 20

Page 18 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT. February 12, 2021
Revision 1, February 17, 2021
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99
THIS PAGE INTENTIONALLY LEFT BLANK.

### Page 21

Page 19
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE STATEMENT ON THE TITLE PAGE OF THIS DOCUMENT.
HERCULES Lockheed Martin Aeronautics CompanyMarietta, Georgia 30063
ALERT SERVICE BULLETIN
A382-57-99February 12, 2021
Revision 1, February 17, 2021
3. MATERIAL INFORMATION
The following material, required to inspect each aircraft listed in paragraph 1.A.(1), will be provided by the 
aircraft owner/operator: 
_______#______                                                                                                
File:   I-5137
QUANTITY PART NUMBER NOMENCLATURE NOTE
A/R ASTM D 770 Isopropyl Alcohol 1
A/R EC1252 Torque Stripe Paint 1
A/R MIL-PRF-81733 Class I, Grade A Sealant 1
A/R MIL-PRF-87937 Cleaning Compound 1
NOTE: 1. Local purchase/local supply item.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
