# Lockheed Service Bulletin 382-57-95: No revision named

- Rights: © LOCKHEED MARTIN CORPORATION. Filed by the FAA in regulations.gov docket FAA-2014-0749; AD 2015-05-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lockheed Service Bulletin 382-57-95](https://openairdocs.org/service-documents/lockheed/sb-382-57-95.md)
- Title as filed: SB382-57-95
- Pages: 25
- PDF: https://openairdocs.org/files/sha256/fc/6e/fc6ebf0937d7b36f7957df73ec04cc903a2481d4bd5a4ffcbc397a30b331f1f7
- Page: https://openairdocs.org/service-documents/lockheed/sb-382-57-95/file/fc6ebf0937d7

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
 
EXPORT CONTROLLED INFORMATION 
WARNING - This document contains data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et 
seq.) as amended, or the Export Administration Act (Title 50, U.S.C., App 2401 et seq.) as amended.  Violations of these export laws 
are subject to severe criminal and civil penalties. 
© 2013 LOCKHEED MARTIN CORPORATION.  LOCKHEED MARTIN PROPRIETARY INFORMATION.  
December 16, 2013 382-57-95 
 Page 1 of 17 
WINGS - OUTER WING UPPER AND LOWER RAINBOW FITTING INSPECTION FOR CRACKS AND 
REPLACEMENT  
 
NOTE: This Service Bulletin includes Appendix A. 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
This service bulletin is applicable to all Model 382, 382B, 382E, 382F, and 382G series FAA certificated 
Hercules aircraft having Outer Wing Serials 4542 or later, or all MEP replacement outer wings except the 
14Y Series (Part No. 388021-9/-10). 
B. REASON 
(1) Fatigue cracking of the outer wing upper and lower rainbow fittings on the durability test and on 
in-service aircraft indicates a requirement to perform inspections of the rainbow fittings.  Analysis 
of in-service cracking has shown that these fittings are susceptible to Multiple Site Damage 
(MSD) and an inspection is required to ensure that cracking does not occur in the skin 
panel-to-fitting fastener holes, resulting in an unacceptable reduction in residual strength.  The 
inspection intervals provided in this service bulletin will ensure that the probability of failure 
remains acceptably low until the rainbow fittings are replaced. 
(2) The 14 CFR Part 26, Subpart C Aging Aircraft Safety - Widespread Fatigue Damage rule became 
effective on January 14, 2011.  In compliance with this rule, Lockheed Martin Aeronautics 
Company established a Limit of Validity (LOV) for 382 series aircraft, published in Section VII of 
customer specific Service Manual Publication (SMP) 515-C Inspection Programs.  14 CFR Part 
121 or Part 129 operators must have incorporated the LOV into their maintenance program by 
July 14, 2013 to comply with FAR §121.1115 or §129.115.  This service bulletin incorporates 
maintenance actions required for the outer wing rainbow fittings to safeguard the airc raft against 
widespread fatigue damage up to the LOV. 
(3) Lockheed Martin Aeronautics Company recommends that inspections specified herein be 
accomplished on all commercial aircraft outer wings that have accumulated 30,000 or more flight 
hours.  The initial inspection should be performed at the next convenient maintenance period but 
not to exceed 365 days or 600 flight hours, whichever occurs first, after receipt of this Service 
Bulletin.  Recurring inspection is recommended at 2,000 flight hours. 
(4) Lockheed Martin Aeronautics Company recommends that both upper and lower rainbow fittings 
be replaced at 50,000 flight hours.  This replacement coincides with center wing replacement per 
Service Bulletin 382-57-94.  Replacement of the rainbow fittings will reset the flight hours to zero 
with respect to the inspection requirements identified in this Service Bulletin . 
NOTE: For commercial operators of aircraft with outer wings that have had previous military usage, 
contact Lockheed Martin for adjusted compliance times.

### Page 2

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 2  
NOTE: The replacement times indicated in this service bulletin do not apply to military operators of 
382, 382B, 382E, 382F, and 382G aircraft.  Contact Lockheed Martin for an Operational 
Usage Evaluation/Service Life Assessment to determine an appropriate replacemen t 
schedule. 
C. DESCRIPTION 
(1) This Service Bulletin contains instructions for inspecting outer wing upper and lower rainbow 
fittings using Eddy Current Surface Scan to detect cracks propagating from fasteners attaching 
the fittings to skin panels.  Perform inspections in accordance with Paragraph 2.A. of this Service 
Bulletin. 
(2) This Service Bulletin contains instructions for replacing upper and lower rainbow fittings on the 
outer wing.  Prior to installation of new rainbow fittings, inspect all open fastener holes in mating 
structure using Automated Bolt Hole Eddy Current as defined in Appendix A of this Service 
Bulletin.  Make necessary repairs and install new rainbow fittings in accordance with 
Paragraph 2.B. of this Service Bulletin. 
D. APPROVAL 
(1) The aircraft owner/operator will make an appropriate entry in the aircraft log records upon 
compliance with this Service Bulletin. 
(2) After the work has been completed on each affected aircraft, please complete and mail or fax 
(770-494-5682) a Notice of Service Bulletin Compliance; or notify Lockheed Martin Aeronautics 
Company of compliance with this Service Bulletin at website address:  
http://www.lockheedmartin.com/eoc and log into Data Library. 
(3) This Service Bulletin has been approved by the FAA as complying with applicable Federal 
Aviation Regulations. 
E. MANPOWER 
The work prescribed in this Service Bulletin has not been performed at the Lockheed Martin facility.  
Therefore, the manpower estimates provided have not been validated, and should not be const rued as 
being acceptable for use in making fixed price quotes for accomplishment of the work.  These estimates 
are provided only as a convenience for customer planning purposes.  It is estimated that manhours 
required, crew size, and elapsed time while the aircraft is out of service are as follows: 
TASK MANHOURS CREW SIZE ELAPSED TIME 
Primary ECSS Inspection 24 2 12 hrs 
Removal and Installation of one fitting 515 6 285 hrs 
Primary BHEC Inspection 24 2 12 hrs

### Page 3

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 3  
NOTE: This Service Bulletin is based upon the configuration of the aircraft as it was delivered from 
Lockheed Martin Aeronautics Company.  Previous service bulletins issued by Lockheed Martin 
Aeronautics Company have been considered in the preparation of this Service Bulletin, but no 
consideration has been given to peculiar changes made to the aircraft by the owner/operator 
since its delivery. 
F. MATERIAL - COST AND AVAILABILITY 
(1) Parts/Materials listed in section 3 of this service bulletin are to be supplied by the a ircraft 
owner/operator.  Parts listed in section 3 of this service bulletin may also be purchased from 
Lockheed Martin, if desired.  Parts bearing Lockheed Martin Aeronautics Company part numbers 
are considered proprietary and shall be purchased from Lockheed Martin Aeronautics Company 
unless methods of fabrication are shown in this publication.  Inquiries concerning current prices, 
applicability, and availability of kits may be directed to the following: 
   MAIL:   Lockheed Martin Aeronautics Company 
     C-130 Commercial Contracts 
     Department F532 
     Zone 0195 
     86 South Cobb Drive 
     Marietta, GA 30063-0195, USA 
   TELEPHONE: (770) 494-5165 
   FAX:   (817) 655-9700 
(2) Additional bulk materials, not included in the kit, will be supplied by the aircraft owner/operator. 
G. TOOLING - PRICE AND AVAILABILITY 
(1) For ECSS Inspections: 
Eddy current inspection unit, Nortec 2000D/D+, or equivalent. 
Probe, shielded, right angle, 1/2-inch drop, 50-500 kHz, Fischer/LEMO Triax Connector, Olympus 
MTF-905-60, or equivalent. 
Probe, shielded, straight, 50-500 kHz, Fischer/LEMO Triax Connector, Olympus MTF-40, or 
equivalent. 
Cable, 6 foot, Fischer/LEMO Triax to 16-pin LEMO connector, Olympus P/N 9122244, or 
equivalent. 
Calibration Standard, aluminum, VM Products, Inc. P/N VM30889-C1A or P/N VM30889-C1A/AF, 
or equivalent. 
(2) For BHEC Inspections defined in Appendix A: 
Eddy current instrument, Nortec 2000D/D+, or equivalent 
Scanner, high-speed, MiniMite, 4-pin Fischer, Olympus P/N 9744738, or equivalent.

### Page 4

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 4  
Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/16-inch diameter (.156-.187), 4-pin 
Fischer, Olympus SPO-5965, P/N 9230061, or equivalent. 
Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 1/4-inch diameter (.218-.250), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219980, or equivalent. 
Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 5/16-inch diameter (.281-.312), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219982, or equivalent. 
Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/8-inch diameter (.312-.375), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219982, or equivalent. 
Cable, scanner, high-speed, 16-pin Lemo, Olympus P/N 9122090, or equivalent. 
Calibration Standard, aluminum, VM Products, Inc. P/N VM30889-C1A or P/N VM30889 C1A/AF, 
or equivalent. 
(3) For Removal and Installation of Rainbow Fitting: 
3307043-1/2-16F Fixture to locate the new joint fitting. 
3307043-1/2-18F Fixture to mill the nodes of the new joint fitting. 
185R105-002A Router, or equivalent, for milling the new joint fitting. 
446E101-015C Cutter, or equivalent, for above router. 
730M200-004A Depth Micrometer or equivalent. 
Jig Transit (with Optical micrometer) or equivalent. 
H. WEIGHT AND BALANCE 
None. 
I. REFERENCES 
SMP 515-C-NDI, Nondestructive Inspection (NDI) Procedures Manual Supplement 
SMP 581, Hercules Maintenance Manual 
SMP 583, Structural Repair Manual 
Hercules Airfreighter Progressive Inspection Procedures 
Service Bulletin 382-57-94/ Wings - Replacement of Center Wing 
The following Lockheed Martin drawings may be needed for reference: 
 
DWG NO. DESCRIPTION OUTER WING EFFECTIVITY* 
3308150 Outer Wing Assy 4542 thru 4960 
3319669 Outer Wing Assy 4992 thru 5320

### Page 5

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 5  
DWG NO. DESCRIPTION OUTER WING EFFECTIVITY* 
3308152 Box Structure, Outer Wing 
Assy 
4542 thru 4960 
3319672 Box Structure, Outer Wing 
Assy 
4992 thru 5320 
3308153 LWR Surface Instl 4542 thru 4960 
3325532 LWR Surface Instl 4992 thru 5320 
3308154 UPR Surface Assy 4542 thru 4960 
3325535 UPR Surface Assy 4992 thru 5320 
3308155 UPR Surface Instl 4542 thru 4960 
3325531 UPR Surface Instl 4992 thru 5320 
3308156 LWR Surface Assy 4542 thru 4960 
3325536 LWR Surface Assy 4992 thru 5320 
370500 Wing Joint Basic Dimension All 
* Outer wing serial number is indicated on the outer wing identification placard located on 
the rear beam web near OWS180. 
 
J. OTHER PUBLICATIONS AFFECTED 
Hercules Airfreighter Progressive Inspection Procedures

### Page 6

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 6  
THIS PAGE INTENTIONALLY LEFT BLANK.

### Page 7

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 7  
2. ACCOMPLISHMENT INSTRUCTIONS 
A. INITIAL AND RECURRING INSPECTIONS 
This service bulletin defines the initial inspection for cracks in outer wing upper and lower rainbow 
fittings on commercial aircraft at 30,000 flight hours and a recurring inspection at intervals of 2,000 flight 
hours.  Perform nondestructive inspection of the outer wing upper and lower rainbow fitting to skin panel 
attachments, left and right, as shown in Figure 1 and Figure 2.  The upper and lower inspection areas 
are located at OWS 3 to OWS 7 between the forward and aft corner fittings and include 2 inboard  
chord-wise fastener rows containing approximately 180 fasteners. 
The wing joint rainbow fittings are fabricated from 7075-T73511 aluminum.  The rainbow fitting tangs 
taper in thickness from approximately 0.35 to 0.10 inches in the inspection areas.  The u pper and lower 
surface skin panels are attached to the rainbow fittings in the inspection areas with steel fasteners.  
Cyclic loading may cause fatigue cracks to begin in the rainbow fitting at the panel attachment fasteners 
and propagate in a chord-wise direction. 
These inspections shall be performed as follows: 
NOTE: For support data and locally manufactured items and acceptance/rejection criteria, refer to 
the SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement.  
(1) NDI equipment:  Required equipment is listed in Paragraph 1.G.(1). 
(2) Access: Access to the upper and lower wing surfaces may be accomplished using appropriate 
maintenance stands.  Use safety restraint harnesses or other available safety equipment when 
working on top of the wings. 
(3) Preparation of parts: Remove sealant, scaling paint, oil, and grease in the inspection areas using 
the procedures detailed in the SMP 515-C-NDI Nondestructive Inspection Procedures Manual 
Supplement, Section 20-00-00. 
(4) Instrument settings/calibration: Set up and calibrate the eddy current instrument as specified in 
SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement, Section 20 -10-04 for 
eddy current scanning of aluminum.  The calibration standard is specified in Paragraph 1.G.(1).  
See Figure 3 for the expected signal responses after calibration of the surface scanning probes 
noted in this inspection. 
NOTE: The eddy current instrument must be recalibrated when probes are changed.  
(5) Inspection - Upper Surface: 
(a) Scan around all fasteners attaching the upper rainbow fitting to the wing skin panels as 
illustrated in Figure 1.  Use the raised fastener heads as a guide when inspecting around 
the fasteners in the inspection area.  Fatigue cracking is expected to propagate in a 
chord-wise (fore-aft) direction. 
(b) An instrument screen presentation, as noted during calibration, will indicate a suspected 
defect in the part being inspected.

### Page 8

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 8  
(6) Inspection - Lower Surface: 
(a) Scan around all fasteners attaching the lower rainbow fitting to the wing skin panels as 
illustrated in Figure 2.  Use the raised fastener heads as a guide when inspecting around 
the fasteners in the inspection area.  Fatigue cracking is expected to propagate in a 
chordwise (fore-aft) direction. 
(b) An instrument screen presentation, as noted during calibration, will indicate a suspected 
defect in the part being inspected. 
(7) Mark and report suspected defects. If defects are suspected, proceed to the Backup NDI 
Procedure.  If no defects are suspected, complete the Primary NDI Procedure and proceed to 
System Securing. 
(8) BACKUP NDI PROCEDURE 
(a) To confirm suspected defects, remove the fastener and perform an Automated Bolt Hole 
Eddy Current inspection of the open hole in accordance with Appendix A. 
(b) Report any damage detected by this inspection procedure to Lockheed Martin Aeronautics 
Company Enterprise Operations Center in accordance with the note at the end of the 
accomplishment instructions.  Provide the following information for all damage detected: 
1 Aircraft Serial Number. 
2 Outer Wing Flight Hours (or Aircraft Flight Hours if outer wing hours are unknown). 
3 Part number and description. 
4 Location (Wing Station, Fuselage Station) and specific fastener hole location. 
5 Length, depth, and orientation of crack. 
NOTE: Prior to reporting any detected damage to Lockheed Martin Aeronautics Company, it is 
recommended that a borescope inspection (side view lens) of the hole bore be performed to 
determine if the reported damage is due to fatigue cracking, embedded metal at fa ying 
surfaces or mechanical damage (gouging, reamer/drill marks, elongation) within the hole 
bore. 
(9) SYSTEM SECURING.  Restore finishes and sealants, reinstall removed components, remove 
equipment and supplies from the inspection area, and perform operational checkouts as required 
in accordance with applicable maintenance instructions. 
B. REPLACEMENT OF WING JOINT FITTINGS 
(1) This Service Bulletin recommends replacement of the outer wing upper and lower rainbow fittings 
in accordance with Hercules Maintenance Manual on commercial aircraft outer wings having 
accumulated more than 50,000 total flight hours.

### Page 9

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 9  
(2) Preparation for Replacement 
(a) Perform Alignment and Symmetry on aircraft in accordance with SMP 583 Structural 
Repair Manual, Chapter 51-100-00.  Retain this data for future reference. 
(b) Remove outer wings using instructions in SMP 581 Fig 57-10-03 and place wings on 
cradle.  Secure the cradle with mechanical locks to avoid movement during Step 2.B.(2)(c).  
Shoring is required if cradle cannot be mechanically locked. 
(c) Conduct a survey of the OWS 0 outer wing joint plane using a suitable optical transit.  
Record any disparity in planarity between all nodes.  Reference drawings 3308150 and 
3319669.  Contact Lockheed Martin if the four corner fittings are not co-planar within 
drawing requirements. 
(d) Remove all components such as plumbing and wiring necessary to facilitate installation of 
replacement rainbow fittings in area between OWS 0 and OWS 7. 
(3) Upper Rainbow Fitting Replacement 
CAUTION: REPLACE UPPER OR LOWER RAINBOW FITTINGS ONE AT A TIME.  UNDER NO 
CIRCUMSTANCES SHOULD THE RAINBOW FITTINGS AND SPAR CAP CORNER 
FITTINGS BE REMOVED AT THE SAME TIME.  THE CORNER FITTINGS ARE USED 
AS A REFERENCE IN THE MACHINING OF THE RAINBOW FITTINGS AND 
SHOULD NOT BE REMOVED UNTIL THE MACHINING OF THE RAINBOW FITTINGS 
HAS BEEN COMPLETED. 
CAUTION: EXERCISE CAUTION WHEN INSTALLING OR REMOVING THE NEW RAINBOW 
FITTING TO AND FROM THE WING.  AVOID APPLYING UNDUE FORCE DURING 
THIS PROCESS TO PREVENT CRACKING THE FITTING AND OTHER WING 
COMPONENTS. 
(a) Remove upper rainbow fitting by removing attaching fasteners and breaking fay surface 
sealant.  Use caution to avoid damage to wing structure and attach holes.  
(b) Clean wing attaching structure such as skin panels, stiffeners, corner fittings, attaching 
angles, and rib web of sealant and other particles. 
(c) Visually inspect the wing faying structure for possible damage or cracks.  
(d) Perform Automated Bolt Hole Eddy Current inspection of all open fastener holes in skins, 
stiffeners, webs, and angles while fitting is removed in accordance with Appendix A of this 
Service Bulletin.  If confirmed cracks are found, repair in accordance with Hercules 
Structural Repair Manual SMP 583 or contact Lockheed Martin Aeronautics Company 
Enterprise Operations Center in accordance with the note at the end of the 
accomplishment instructions. 
(e) Place the new rainbow fitting in the wing.  Some amount of force may be required to 
properly align fitting.  Reference Drawing 3308154 or 3325535 Upper Surface Assembly.

### Page 10

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 10  
(f) Install 3307043-1/2-16F Locating Fixture and attach it to the four corner fittings.  A shim of 
suitable size and thickness must be placed between the fixture and each of the four corner 
fittings to allow the rainbow fitting nodes to protrude for final node milling to assure joint 
planarity.  All four shims must be the same thickness.  Reference Drawing 3308152 or 
3319672 for wing joint node thickness requirements.  All nodes of the rainbow fitting shall 
be tight against fixture before proceeding. 
(g) Check all fitting-to-wing skin panel attaching fastener holes for proper edge distance (1.5 x 
Final Hole Diameter minimum.) 
(h) Visually check the new rainbow fitting for proper placement/alignment prior to drilling 
operations. 
(i) Transfer all fastener holes from outer wing mating structure to new rainbow fi tting in 
accordance with SMP 583 Structural Repair Manual, Chapter 51-70. 
(j) Remove the locating fixture and rainbow fitting from wing.  Clean fitting and the 
surrounding wing area for debris and burrs. 
(k) Reposition the new rainbow fitting in the wing, picking up previously drilled holes.  Fay 
surface seal in accordance with SMP 583 Structural Repair Manual. 
(l) Wet install oversize fasteners of appropriate type in accordance with SMP 583 Structural 
Repair Manual, Chapter 51-70. 
NOTE: Perform Step 2.B.(4) Lower Rainbow Fitting Replacement before performing Step 
2.B.(5) Fitting Node Milling Procedure. 
(4) Lower Rainbow Fitting Replacement 
CAUTION: EXERCISE CAUTION WHEN INSTALLING OR REMOVING THE NEW RAINBOW 
FITTING TO AND FROM THE WING.  AVOID APPLYING UNDUE FORCE DURING 
THIS PROCESS TO PREVENT CRACKING THE FITTING AND OTHER WING 
COMPONENTS. 
(a) Remove lower rainbow fitting by removing attaching fasteners and breaking fay surface 
sealant.  Use caution as to not damage wing structure and attach holes. 
(b) Clean wing attaching structure such as skin panels, stiffeners, corner fittings, attaching 
angles, and rib web of sealant and other particles. 
(c) Visually inspect the wing faying structure for possible damage or cracks.  
(d) Perform Automated Bolt Hole Eddy Current inspection of all open fastener holes in mating 
structure while fitting is removed in accordance with Appendix A of this service bulletin.  If 
confirmed cracks are found, repair in accordance with Hercules Structural Repair Manual 
SMP 583 or contact Lockheed Martin Aeronautics Company Enterprise Operations Center 
in accordance with the note at the end of the accomplishment instructions . 
(e) Place the new rainbow fitting in the wing.  Some amount of force may be required to 
properly align fitting.  Reference Drawing 3308156 or 3325536 Lower Surface Assembly 
for proper fit and installation.

### Page 11

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 11  
(f) Install P/N 3307043-1/2-16F locating fixture and attach it to the four corner fittings.  A shim 
of suitable size and thickness must be placed between the fixture and each of the four 
corner fittings to allow the rainbow fitting nodes to protrude for final node milling to assure 
joint planarity.  All four shims must be the same thickness.  Reference Drawing 3308152 or 
3319672 for wing joint node thickness requirements.  All nodes of the rainbow fi tting shall 
be tight against fixture before proceeding. 
(g) Check all fitting-to-wing skin panel attaching fastener holes for proper edge distance (1.5 x 
Final Hole Diameter minimum) 
(h) Visually check the new rainbow fitting for proper placement/alignment prior to drilling 
operations. 
(i) Transfer all fastener holes from outer wing mating structure to new rainbow fitting  in 
accordance with SMP 583 Structural Repair Manual, Chapter 51-70. 
(j) Remove the locating fixture and rainbow fitting from wing.  Clean components and the 
surrounding wing area for debris and burrs. 
(k) Reposition the new rainbow fitting in the wing, picking up previously drilled holes .  Fay 
surface seal in accordance with SMP 583 Structural Repair Manual. 
(l) Wet-install oversize fasteners of appropriate type in accordance with SMP 583 Structural 
Repair Manual, Chapter 51-70. 
NOTE: Continue to Step 2.B.(5) Fitting Node Milling Procedure only after completing Steps 
2.B.(3) and 2.B.(4). 
(5) Fitting Node Milling Procedure 
(a) This step is required for milling procedures:  Support the outer wing using instructions in 
SMP 581 Fig 57-10-03.  Secure the cradle with mechanical locks to avoid movement 
during machining.  Shoring is required if cradle cannot be mechanically locked. 
(b) Position optical transit as required to adequately read the location of the rainbow fittings.  
Adjust the cradle until the four corner fitting node faces are in the same vertical plane .  This 
step will not be necessary if a suitable transit is used that is equipped with degrees of 
freedom that permit setting the transit line of sight in a non-vertical plane with the four 
corner fitting nodes.  Verify that the four corner fitting nodes are coplanar and check the 
amount of rainbow fitting node face protrusion.  Node thickness requirements are defined 
by engineering drawing 3308152 and 3319672. 
(c) Ensure that Steps 2.(5)(a) and 2.(5)(b) are completed before milling. 
(d) Position milling fixture 3307043-1/2-18F Left or Right to the outer wing.  Using a proper 
router with micro depth adjustment as specified in paragraph 1.G.(3), measure the depth to 
corner fitting nodes.  Cross check using the transit.  Verify that the milling operation will 
yield the node thickness requirements as defined by Drawings 3308152 or 3319672.  Use 
router to mill each node. 
(e) Continue the same procedure until all upper and lower rainbow fitting nodes are milled to 
the same plane as the corner fittings.  Always cross check optically with transit.

### Page 12

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 12  
(f) Remove milling fixture. 
(g) Ream wing mate holes to final size in accordance with Drawing 370500.  Chamfer sharp 
edges of wing mate holes in accordance  with Drawing 3308152 or 3319672.  
(h) Touch-up finish the milled nodes with Alodine and one coat of AMS-C-27725 Polyurethane, 
or equivalent in accordance with Drawings 3308152 or 3319672. 
(6) Final Installation 
(a) Re-install any components removed to facilitate replacement of the rainbow fittings.  
(b) Re-install outer wings per SMP 581, Figure 57-10-03. 
(c) Perform an Alignment and Symmetry Check and compare readings to those taken at the 
start of procedure. 
C. RESTORE AIRCRAFT TO SERVICE 
Perform necessary functional checks of interrupted systems per SMP 581, Figure 57-10-03, Step 39 
and return aircraft to service. 
NOTE: If assistance is needed, contact your local Lockheed Martin Aeronautics Company Representative, or 
the Enterprise Operations Center - Technical Support in Marietta, Georgia, USA, as follows: 
 
TELEPHONE: (770) 494-9131 
 
FAX:  (770) 494-9122 
 
E-MAIL:  hercules.support@lmco.com 
  
MAIL:  Lockheed Martin Aeronautics Company 
    86 South Cobb Drive 
    Dept. 3E1M, Zone 0591 
   Marietta, GA 30063, USA

### Page 13

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 13  
FWD
OTBD
VIEW LOOKING DOWN ON LEFT WING.  
RIGHT WING OPPOSITE . 
UPPER
RAINBOW 
FITTING
UPPER SKIN PANEL
UPPER
RAINBOW 
FITTING
ECSS AROUND EACH FASTENER IN 
THE TWO (2) INBOARD ROWS 
ATTACHING RAINBOW FITTING TO 
SKIN ON UPPER EXTERIOR 
SURFACE OF EACH OUTER WING.
A
SECTION B-B
ROTATED 90 DEG CW
 
 
 
 
 Eddy Current Surface Scan Inspection of Outer Wing Upper Rainbow Fitting 
 Figure 1

### Page 14

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 14  
FWD
OTBD
VIEW LOOKING UP ON RIGHT WING.  
LEFT WING OPPOSITE . 
LOWER
RAINBOW 
FITTING
LOWER SKIN PANEL
LOWER
RAINBOW 
FITTING
A
SECTION B-B
ROTATED 90 DEG CW
ECSS AROUND EACH FASTENER IN 
THE TWO (2) INBOARD ROWS 
ATTACHING RAINBOW FITTING 
TO SKIN ON LOWER EXTERIOR 
SURFACE OF EACH OUTER WING.
FUS STA
517.00
OWS
0.00
 
 Eddy Current Surface Scan Inspection of Outer Wing Lower Rainbow Fitting 
 Figure 2

### Page 15 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
SERVICE BULLETIN
60% FSW (MIN.)
100% VSH
80% FSH
0.020: DEEP
EDM NOTCH  50% VSH
NULL
POINT
LIFT-OFF
0% VSH
0%  50%  100%
HSW  HSW  HSW
Signal Response from 0.020" Deep EDM Notch
(Aluminum, Weakly Ferromagnetic & Non-Ferromagnetic Alloys)
0.020" DEEP
EDM NOTCH
0.010" DEEP
EDM NOTCH
0.005" DEEP
EDM NOTCH
Signal Responses from 0.005", 0.010" & 0.020" Deep EDM Notches
(Aluminum, Weakly Ferromagnetic & Non-Ferromagnetic Alloys)
Calibrated Lift-Off and EDM Notch Responses for Eddy Current Surface Scan
Figure 3
December 16, 2013  USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT.  382-57-95
Page 15

### Page 16

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 
Page 16  
THIS PAGE INTENTIONALLY LEFT BLANK.

### Page 17

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 
 Page 17 
3. MATERIAL INFORMATION 
The following parts/materials, required to modify each aircraft listed in paragraph 1.A., will be provided by the 
aircraft owner/operator.  Parts may be obtained from Lockheed Martin Aeronautics Company in accordance 
with paragraph 1.F. 
NEW PART 
NUMBER 
QTY. PER 
WING 
 
KEY WORD 
OLD PART 
NUMBER 
INSTRUCTIONS/  
DISPOSITION 
3308183-9/-10 1 each Upper Surface Rainbow 
Fitting 
3308183-3/-4 Note 1 
3308183-9/-10 1 each Upper Surface Rainbow 
Fitting 
3308183-9/-10 Note 2 
3308182-9/-10 1 each Lower Surface Rainbow 
Fitting 
3308182-3/-4 Note 1 
3308182-9/-10 1 each Lower Surface Rainbow 
Fitting 
3308182-9/-10 Note 2 
 
NOTE: 1. Applies to outer wings originally installed on Serials* 4542 thru 4765. 
 
2. Applies to outer wings originally installed on Serials* 4766 thru 5320. 
* Outer wing serial number is indicated on the outer wing identification placard located on 
the rear beam web near OWS180. 
 _______#______                                                    
File: I-3684

### Page 18

(No text on this page.)

### Page 19

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 APPENDIX A 382-57-95 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT.  
  Page A1 of A7 
APPENDIX A 
AUTOMATED BOLT HOLE EDDY CURRENT INSPECTION PROCEDURE  
 
1. PRIMARY NDI PROCEDURE - AUTOMATED BOLT HOLE EDDY CURRENT 
NOTE: For support data and locally manufactured items and acceptance/rejection criteria, refer to the 
Nondestructive Inspection (NDI) Procedures Manual Supplement. 
A. NDI Equipment: 
(1) Eddy current instrument, Nortec 2000D/D+, or equivalent. 
(2) Scanner, high-speed, MiniMite, 4-pin Fischer, Olympus P/N 9744738, or equivalent. 
(3) Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/16-inch diameter (0.156-0.187), 4-pin 
Fischer, Olympus SPO-5965, P/N 9230061, or equivalent. 
(4) Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 1/4-inch diameter (0.218-0.250), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219980, or equivalent. 
(5) Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 5/16-inch diameter (0.281-0.312), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219982, or equivalent. 
(6) Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/8-inch diameter (0.312-0.375), 4-pin 
Fischer, Olympus SPO-5965, P/N 9219982, or equivalent. 
(7) Cable, scanner, high-speed, 16-pin Lemo, Olympus P/N 9122090, or equivalent. 
(8) Calibration standard, aluminum - VM Products, Inc. P/N VM30889-C1A or P/N VM30889-C1A/AF, 
or equivalent. 
B. Preparation of Part: Remove sealant from the fastener holes with a nylon bristled brush of the 
appropriate diameter and an approved alcohol or solvent.  Refer to the procedures detailed in the 
SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement, Section 20 -00-00 for 
cleaning of the holes to allow for acceptable probe contact with the part. 
C. Equipment Calibration: 
NOTE: Allow the instrument to warm-up for a period of 10-15 minutes prior to performing the 
inspection to minimize drifting of the signal. 
(1) Connect the scanner, cable and the appropriate diameter probe to the eddy current instrument.  
Turn on the instrument and allow it to reach operating temperatures.

### Page 20

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 APPENDIX A December 16, 2013 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT.  
Page A2  
(2) Adjust the initial instrument settings on the equipment to the following : 
MAIN MENU 
Frequency 1 (FREQ) 500 kHz (see Note #1) 
Frequency 2 (FREQ) Off 
Horizontal Gain (H-GAIN) 55 dB 
Vertical Gain (V-GAIN) 55 dB 
Phase Angle (ANGLE) 0° 
FILTER MENU 
Low Pass Filter (LP FILTER) See Note #2 
High Pass Filter (HP FILTER) See Note #2 
Continuous Null (CONT) OFF 
DISPLAY MENU 
Sweep Grid (SWEEP) OFF 
Vertical Screen Position (V-POS) 50% 
Horizontal Screen Position (H-POS) 50% 
Persistence (PERSIS) OFF 
Display Erase Rate (DIS ERASE) 0.2 sec 
Grid Display (GRATICLE) ON 
Focal Spot Shape (DOT/BOX) DOT 
SETUP MENU 
Frequency (1) SINGLE 
Probe Drive (4) HIGH 
Scanner Rotation Rate (RPM) 1300 
Sync Angle (SYNC ANG) 0 
NOTES: 
1. The frequency may be adjusted within the 200-500 kHz range to maintain an improved signal 
response. Higher frequencies will result in greater sensitivity to surface defects; whereas, 
lower frequencies will result in reduce noise levels and better resolution of sub -surface 
defects. 
2. When required, utilize the noted low pass and high pass filter settings for the following probe 
diameters: 
 1/8ʺ-7/32ʺ D. (0.156ʺ-0.219ʺ D.), LPF of 500 Hz, HPF of 150 Hz 
 7/32ʺ-5/16ʺ D. (0.219ʺ-0.312ʺ D.), LPF of 500 Hz, HPF of 200 Hz 
 5/16ʺ-7/16ʺ D. (0.312ʺ-0.437ʺ D.), LPF of 700 Hz, HPF of 300 Hz 
(3) Turn on the scanner.  With the probe placed in the air, press the NULL soft key on the instrument 
and wait for nulling to complete.  The null point on the impedance plane should be located at the 
screen center at 50% horizontal screen width (HSW) and 50% vertical screen height (VSH).  
(4) Place the probe on the calibration standard, normal to the surface and away from any edges, 
holes, or EDM notches as illustrated in Figure A1.  Generate an initial lift-off response and verify 
the initial lift-off has a narrow response as illustrated in Figure A1.  If a wide looped lift-off is 
noted, press the V-GAIN soft key and reduce the vertical gain until a flat line response is 
achieved.

### Page 21

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 APPENDIX A 382-57-95 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 
 Page A3 
(5) If the lift-off response is not horizontal, press the ANGLE soft key and adjust the phase angle until 
the lift-off response is as near horizontal as possible.  See Figure A1 for an illustration of the 
expected phase adjusted lift-off response. 
(6) Insert the probe into the appropriate diameter hole in the calibration standard adjacent to the 
0.030” X 0.030” notch located at the Layer 1-2 interface (on calibration standard VM30889-C1A or 
–C1A/AF) or adjacent to the 0.030ʺx0.030ʺ notch on an equivalent standard.  
(7) Maximize the notch response on the impedance plane screen, press the H-GAIN soft key and 
adjust the horizontal notch response to 50% full screen width (FSW).  Press the V-GAIN soft key 
and adjust the vertical notch response to 50% full screen height (FSH).  Confirm the notch 
response has a 45 degree angle and orientation from the upper left corner to the lower right 
corner of the impedance plane screen. 
(8) Press the GAIN soft key and adjust the notch response until an 80% FSW and 80% FSH 
response is achieved.  The notch response should have a symmetric "Figure 8" pattern split 
above and below the lift-off line/null point located at the 50% VSH location.  The lift-off noise, 
resulting from probe rotation or "chattering" in the hole should be maintained below 40% FSW.  
See Figure A2 for the expected calibrated notch response and the acceptable limits for lift -off 
noise. 
NOTE: If a symmetric notch response cannot be achieved, slight adjustments (± 100 Hz) may be 
made to the low-pass and hi-pass filter settings to improve symmetry of the notch response. 
(9) The instrument is now properly calibrated for the impedance plane screen.  No additional 
changes should be made to the phase setting from this point forward, unless a new calibration is 
being performed.  Any additional changes to the phase angle will result in a change in lift-off from 
the horizontal orientation earlier established. 
(10) Press the DISPLAY soft key, then press the SWEEP soft key twice to enter SWEEP EXTRN 
mode. 
NOTE: Instrument adjustment made at this time will only affect the sweep screen notch response and 
will have no effect on the impedance plane screen calibration. 
(11) With the probe placed in the air, press the NULL soft key on the instrument, and wait for nulling to 
complete.  The null baseline response on the sweep screen should be located at the center of the 
instrument screen at the 50% VSH position. 
(12) Turn the scanner on and reinsert the probe into the same hole in the calibration standard.  Locate 
the 0.030” x 0.030” EDM notch and maximize the notch response on the sweep scre en. 
(13) Press the GAIN soft key and adjust the notch response until an 80% FSH response is achieved .  
The notch response should be symmetric above and below the null baseline and the noise level 
of the baseline should be below 20% FSH.  See Figure A2 for the expected calibrated notch 
response and the acceptable limits for baseline noise. 
(14) The instrument is now calibrated for completion of the inspection requirements for the fastener 
holes within the diameter range of the probe being used.

### Page 22

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
382-57-95 APPENDIX A December 16, 2013 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT.  
Page A4  
D. Inspection: 
NOTE: The eddy current instrument must be recalibrated when probes are changed. 
(1) Ensure instrument is calibrated as in accordance with Paragraph 1.C. Perform ABHEC scan of all 
open holes through all structural layers. 
(2) To confirm suspected damage, conduct a redundant ABHEC backup procedure in accordance 
with Paragraph 2. 
E. Mark and report suspected defects.  If defects are suspected, proceed to the Backup NDI Procedure .  If 
no defects are suspected, complete the Primary NDI Procedure.  
2. BACKUP NDI PROCEDURE - REDUNDANT AUTOMATED BOLT HOLE EDDY CURRENT 
NOTE: For support data and locally manufactured items and acceptance/rejection criteria, refer to the 
Nondestructive Inspection (NDI) Procedures Manual Supplement. 
A. NDI equipment: Same as Primary NDI Procedure. 
B. Preparation of airplane: Same as Primary NDI Procedure. 
C. Preparation of part: Re-clean and/or hone the hole bore to remove any edge burrs, embedded metal at 
faying surfaces or mechanical damage that may have resulted in defect indications noted during the 
Primary NDI Procedure. 
NOTE: The eddy current instrument must be recalibrated when probes are changed. 
D. Instrument settings/calibration:  Set up and re-calibrate the eddy current instrument as specified in the 
Primary NDI Procedure. 
E. Inspection: Repeat the Primary NDI Procedure

### Page 23

HERCULES     Lockheed Martin Aeronautics Company 
    Marietta, Georgia 30063 
SERVICE BULLETIN 
December 16, 2013 APPENDIX A 382-57-95 
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 
 Page A5 
3. MARK AND REPORT DAMAGE: 
Report any damage detected by this inspection procedure to Lockheed Martin Aeronautics Company.  
Provide the following information of all damage detected: 
A. Aircraft Serial Number. 
B. Outer Wing Flight Hours (or Aircraft Flight Hours if outer wing hours are unknown). 
C. Part number and description. 
D. Location (Wing Station, Fuselage Station) and specific fastener hole location. 
E. Length, depth, and orientation of crack. 
NOTE: Prior to reporting any detected damage to Lockheed Martin Aeronautics Company, it is 
recommended that a borescope inspection (side view lens) of the hole bores be performed to 
determine if the reported damage is due to fatigue cracking, embedded metal at faying 
surfaces, or mechanical damage (gouging, reamer/drill marks, elongation) within the hole 
bore.

### Page 24 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
SERVICE BULLETIN
000000  14 732 346 5532  10000
NOTE:
TO ESTABLISH THE LIFT-OFF RESPONSE, TURN ON THE SCANNER AND NULL THE
INSTRUMENT IN THE AIR. ONCE NULLING HAS COMPLETED, PLACE THE PROBE COIL ON THE
CALIBRATION STANDARD, NORMAL TO THE SURFACE, TO GENERATE AN INITIAL LIFT-OFF
RESPONSE. ADJUST THE PHASE ANGLE, IF REQUIRED, UNTIL A HORIZONTAL LIFT-OFF
RESPONSE IS ACHIEVED.
INITIAL LIFT-OFF RESPONSE  PHASE ADJUSTED LIFT-OFF RESPONSE
BHEC Lift-Off Signal Responses from Probe Coil Placed Normal to Surface of Calibration Standard
Typical Automated Bolt Hole Eddy Current Lift-Off Signal Responses
Figure A1
382-57-95  APPENDIX A  December 16, 2013
USE, COPYING, AND/OR DIS  IS GOVERNED BY THE RESTRICTIVE LEGEND ON T  AGE OF THIS DOCUMENT.
Page A6

### Page 25 (OCR)

HERCULES  Lockheed Martin Aeronautics Company
Marietta, Georgia 30063
SERVICE BULLETIN
100% VSH
: LIFT-OFF
RESPONSE
80%
FSH  50% VSH
LIFT-OFF
NOISE
< 40% FSW
:80% FSW
0% VSH
0%  50%  100%
HSW  HSW  HSW
Impedance Plane Signal Response from Calibrated 0.030" × 0.030" EDM Corner Notch
100% VSH
80% FSH  BASELINE  NOISE
< 20% FSH
50% VSH
(NULL)
. BASELINE
RESPONSE
0% VSH
12  6  12
CLOCK POSITION
Sweep Display Signal Response from Calibrated 0.030" × 0.030" Corner Notch
Typical Impedance Plane and Sweep Display Signal Responses From 0.030" × 0.030" Notch
Figure A2
December 16, 2013  APPENDIX A  382-57-95
USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT.
Page A7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
