# Lycoming Mandatory Service Bulletin 393: Revision C

- Rights: © Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2014-0437; AD 2014-23-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lycoming Mandatory Service Bulletin 393](https://openairdocs.org/service-documents/lycoming/sb-393.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin 393C
- Pages: 3
- PDF: https://openairdocs.org/files/sha256/27/19/2719fdb3c0976c4f9d5ffc4eb5a4a7f188b03051fe2fe5a57b23f01214abca07
- Page: https://openairdocs.org/service-documents/lycoming/sb-393/file/2719fdb3c097

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

TEXTRON Lycoming  MANDATORY
652 Oliver Street  SERVICE BULLETIN
Williamsport, PA 17701 U.S.A.
717/323-6181
DATE:  November 26, 1976  Service Bulletin No. 393B)  393C
(Supersedes Service Bulletin No.
Engineering Aspects are
FAA (DEER) Approved
SUBJECT:  Exhaust Slip Joint Modification
MODELS AFFECTED:  TIGO-541-E  series  engines with serial numbers 101-62 thru 698-62.
Remanufactured engines shipped before September 15, 1976.
NOTE
Engines that  were inspected and modified in accordance with any previous
edition  bulletin  No. 393  require  cable change as
described in step 6.
TIME OF COMPLIANCE:  next 100 hour engine  inspection  engines  modified in
accordance  with  Service  Bulletin No. 378  in which case change is
required in next 25 hours.
methods have been used to  3.  Reassemble exhaust adapter  pipes to
of the exhaust pipe slip  2005 check coopling part number. MVT69163-  transition  assembly  using  new 78083
manifolds. Brieflytensioned  the left and right  Lycoming  P/N LW-12093-5 1s the
No. 368 describes a spring  number  of the correct coupling to be used.
capa U-bolt clamp  in Service Bulletin No.  Inspect  coupling with  the 3 v-band  a depth micrometer as shown  sections of  each
used. Earlier editions of  1n  figure 2. Any dimension obtained under
bulletin provided  for a single then a  • 230  inch  renders the coupling unfit for
assembly to replace the spring  further service.
rods and U-bolts. Since then, sev-
of stretched cables have oc-
curred indicating that the previous 1/16 inch  FLANGE FACE
and double cable assemblies used were
insufficient  secure the manifold; conse-  CHECK ENTIRE CIRCUMFERENCE
this edition provides a larger sin-  OF THIS EDGE FOR CLEARANCE
WITH FACE OF FLANGE
with the following instructions insofar
applicable to the engine being
1. Remove  spring tensioned rod and clamps
OI  u-bolt clamps as may be the case. These
parts are not reused.
2. Inspect exhaust adapter
CHECK FOR DAMAGE
which may prevent  WHICH MIGHT PREVENT
the adapter pipe inside th  FREE MOVEMENT IN
SLIP JOINT
must be .090 inch below
surface of the flange face. Use a hand  INSPECT THIS AREA
ance. (Seet necessary to obtain this clear-  CRACKS  AROUND FLANGE FOR
LW- 13027 or LW-10798 REAR EXHAUST ADAPTER
Figure 1. Exhaust Adapter Pipe Showing
Areas Requiring  Inspection
Page 1 of 3

### Page 2 (OCR)

Service Bulletin No. 393C
installing the couplings around
sure the entire
assembly is in alignment; that is,
flanges must match each other. Sup-
the exhaust  system in this position
couplings around
engage latch. Tighten coupling
to 50 inch pounds initial torque. Tap
erie tensioning with malet to
5. Check torque and continue tightening to
final  torque of 70/80 inch pounds,
ping  coupling until torque reading stabil-
izes.
NOTE
INSIDE DÉPTH OF  Do not exceed tightening torque spec-
ified for couplings, or open them
CLAMPING AREA  enough  to damage the coupling wrap-
Over torqueing  spreads the v-
MUST NOT BE LESS  band section  the  coupling
THAN .230 IN  impairs its retaining qualities.
6. Assemble  clamps LW-14504
Figure 2. Exhaust Manifold Coupling  approximately
Inspection Requirement  joint and IW-14525 clamps on left and right
exhaust pipes. Connect cable assemblies IW-
clamps with attaching parts SID-
STD-2178 washer
NOTE  nuts. Note  that 4 of these new IW-15437
assemblies,  are now 1/8 inch
The exhaust adapter pipes attached to  nos.  5  and  cylinders, the transi-  along with  replace 8 of the previously used  that were 1/16
the  segments attached to  inch diameter. The indicated quantities are
tion assembly, are especially subject  for 2 engines. Attach these cables,
cracks  the area of weldments  enough slack to provide 1/4 inch deflection
and  attaching  Ilanges.  Replace any  after assembly. (See figure
that indicate  such defects.  3.) Tighten nuts to 60 + 10 inch/1bs.
NOTE
The  following  kit to perform this modification is supplied through Avco
Lycoming  Distributors.  ordered  February 1,
Allowance for labor and furi part credit, F. O. B. Williamsport, Pa. will be  accordance  the following schedule. Furnish engine serial
numbers  to your Avco Lycoming Distributor for ordering parts and  submission
of a Warranty Application.
1. Engines in compliance with Service Bulletin No. 378  • •3 hours labor
2. Engines in compliance with Service Bulletin No. 368  • • • • 1 hour labor
No  allowance  for labor is provided for engines that are in compliance with
Service Bulletin No. 393 or 393A; however,  no charge rechly Yeon voLe aming Service Department.  IW-15437 w111
be
Include engine serial numbers with your request  for the cables.
Page 2 of 3

### Page 3 (OCR)

Service Bulletin No. 393C
NOTE: CABLES ARE ATTACHED OUTSIDE
OF THE CLAMP.
STD 2177  NOTE
RIG CABLES (LW-14572) TO PROVIDE
I/4 INCH DEFLECTION WHEN MEASURED
LW-15437  MIDWAY BETWEEN CLAMPS - BOTH SIDES.
CABLES ARE ASSEMBLED ON THE OUT-
SIDE SURFACE OF THE CLAMPS AS
SHOWN IN THE INSERT.
-STD-2178
- STD-2044
W-14525  LW-15437, 2 PLACES
LW-14504
STD 2177 | 4 PLACES  STD  2178
STD  2044)
LW-14525  (2)
Figure 3. Area of Transition Assembly Showing Cable Assembly
PARTS DATA:
Kit No. IW-14608 Exhaust Manifold Retainer (for 2 engines) consists of:
Qty.  Part No.  Description
4  4  LW-14525  LW-14504  Clamp' ASSY:  clamp, exhaust pipe,  exhaust pipe,  2.00 in.
4  LW-15437  Cable
8  STD-2177  Bolt,  1/4-20 × 15/16
8  STD-2178  Washer
8  STD-2044  Gasket, v-band coupling  self-locking
4  78083
* - Inside diameter of clamp is measured with .20 gap at opening.
NOTE: Revision "C" changes cable assembly and quantity required.
19025, 19025-A, 19434, 19591 - These numbers for Avco Lycoming reference only.
Page 3 of 3

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
