# Lycoming Mandatory Service Bulletin 627: Revision C

- Rights: © Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2016-9512; AD 2017-11-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lycoming Mandatory Service Bulletin 627](https://openairdocs.org/service-documents/lycoming/sb-627.md)
- Title as filed: SB 627 C
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/9f/61/9f619e4298f9b16f071d3cd767ab827ece8bbc7a177c1c15fdd1ce6b44f1dd87
- Page: https://openairdocs.org/service-documents/lycoming/sb-627/file/9f619e4298f9

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

LYCOMING.  MANDATORY
652 Oliver Street
Williamsport, PA 17701 U.S.A.  SERVICE BULLETIN
Telephone +1 (800) 258-3279 (U.S. and Canada)
Telephone +1 (570) 323-6181 (International)
Facsimile +1 (570) 327-7101
www.lycoming.com
DATE:  November 17, 2016  Service Bulletin No. 627C
(Supersedes Service Bulletin No. 627B)
Engineering Aspects are
FAA Approved
SUBJECT:  Exhaust System Inspection
MODELS AFFECTED:  Lycoming Engine Model TIO-540-AJ1A
TIME OF COMPLIANCE:  Within 10 flight hours from the date of this Service Bulletin, complete an
initial Exhaust System Inspection in accordance with the Required Action
Steps 1 and 3 in this Service Bulletin
After the initial Exhaust System Inspection, subsequent repetitive Exhaust
System Inspections are to be completed per Table 1 in this Service Bulletin
TREASON FOR REVISION: Changed CO detector lower alarm setting from 35 PPM to 50 PPM; Revised
instruction for weld joint examination and included footer on pages 5, 6, and 7
NOTICE: Incomplete review of all the information in this document can cause errors. Read the entire
Service Bulletin to make sure you have a complete understanding of the requirements.
This Service Bulletin is in response to field reports of exhaust leaks due to cracked welds and exhaust studs
pulling from a cylinder on some Lycoming TIO-540-AJ1A engine models. This Service Bulletin contains
instructions for the mandatory inspection of the exhaust system for ALL Lycoming TIO-540-AJ1A engine
models per the schedule in Table 1.
Table 1
Schedule for Exhaust System Inspections
Engines installed in aircraft  Engines installed in aircraft not equipped with a carbon monoxide detector or
equipped with an operating  with an inoperative carbon monoxide detector
carbon monoxide detector*
After the initial 10-hour  Engines that have accumulated 1000
Exhaust System Inspection,  hours or less time in service since the
complete the:  last Exhaust System Maintenance**
• Exhaust System Inspection  After the initial 10-hour Exhaust
after every 50 hours time in System Inspection, complete the:
service - complete  • Exhaust System Inspection after
Required Actions 1 and 3  every 25 hours time in service -
• Torque Check after every  complete Required Actions 1 and 3
Engines that have accumulated more
than 1000 hours time in service since
the last Exhaust System Maintenance**
After the initial 10-hour Exhaust
System Inspection, complete the:
• Exhaust System Inspection after every
50 hours time in service - complete
Required Actions 1 and 3
100 hours time in service -  • Torque Check after every 100
complete Required  hours time in service - complete
Actions 1, 2, and 3  Required Actions 1, 2, and 3
• Torque Check after every 100 hours
time in service - complete Required
Actions 1, 2, and 3
* An operational carbon monoxide (CO) detector must be an electrochemical CO detector, located on the
instrument panel, and set for a lower alarm threshold of 50 parts per million (PPM).
** Since having maintenance that required the removal/reinstallation or the removal and replacement of any
exhaust system pipe or turbocharger mounting bracket.
ISSUED  REVISED  PAGE NO  REVISION
General Aviation
Manufacturers Association  MO  07  DAY  18  YEAR  16  MO  11  DAY  17  YEAR  16  1 of 7  C
©2016 Avco Corporation. All Rights Reserved
Lycoming Engines is a division of Avco Corporation

### Page 2 (OCR)

/ CAUTION:  TOXIC GASES, SUCH AS CARBON MONOXIDE, FROM LEAKS IN THE
EXHAUST SYSTEM CAN POTENTIALLY ENTER THE COCKPIT.
NOTICE:  The inspections in this Service Bulletin are in addition to the requirements of Service Bulletin
No. SB-614A and AD 2015-10-06. Both are to be accomplished as specified in their respective
compliance times.
Figures in this Service Bulletin are for illustration purposes only; your engine can appear
differently.
Required Action
1. Exhaust System Inspection
A CAUTION: THE ENGINE AND EXHAUST SYSTEM CAN BE HOT AND COULD CAUSE
BURNS. DO NOT CONDUCT THE EXHAUST SYSTEM INSPECTION WITHIN
1 HOUR OF OPERATING THE ENGINE AND UNTIL THE ENGINE AND
EXHAUST ARE COOL.
NOTICE:  To accurately and efficiently assist those who could be experiencing exhaust leaks due to
cracked welds and exhaust studs pulling from a cylinder, Lycoming Engines must collect
certain data and information from you each time you complete this inspection.
This inspection can be done on an engine installed in an airframe.
During this exhaust system inspection and each subsequent inspection thereafter per Table 1, complete
the steps in this Service Bulletin. Record and submit the findings to Lycoming Engines on the attached
form either online or on hardcopy.
NOTICE: It is very important during this inspection to look for and record on the survey any stamped
data on the Exhaust No. 2 and 3 pipes.
The stamped markings for Exhaust Pipe 2 will have one of the following:
• Only the part number (P/N) (Figure 1). All pipes will be stamped with at least the P/N.
• The P/N and the Release ID# (Figure 2)
• The P/N, Release ID#, and a date code (Figure 3)
40622318
L0B23386  51953-- Release IDH
Figure 1  Figure 2
P/N Only on Exhaust Pipe 2  P/N and Release ID# on Exhaust Pipe 2
0B22318 VEE
519  / 27/16
Release ID #  Date Code
Figure 3
P/N, Release ID#, and Date Code on Exhaust Pipe 2
A. Examine Exhaust Pipe 2, identify any stamped markings, and record the data on the survey.
ISSUED  REVISED  PAGE NO  REVISION
MO  DAY  YEAR  MO  DAY  YEAR
2 of 7  C  S.B. 627
07  18  16  11  17  16

### Page 3 (OCR)

The stamped markings for Exhaust Pipe 3 can have:
• Only the P/N (Figure 4). All pipes will be stamped with at least the P/N.
• The P/N and the Release ID# (Figure 5)
(There is no date code on Exhaust Pipe 3)
40B23388 WFP
40B2267  56283-1
Release ID#
Figure 4  Figure 5
P/N Only on Exhaust Pipe 3  P/N and Release ID# on Exhaust Pipe 3
B. Examine Exhaust Pipe 3, identify any stamped markings, and record the data on the survey.
C. Examine the weld joints of the exhaust pipes for all cylinders (Figures 6 and 7). Closely examine
the saddle reinforced weld joints (Figures 8 and 9), especially at Cylinder 3. If any cracks or
damage are found, do not operate the aircraft until repairs are made in accordance with existing
Lycoming publications. Complete and submit the survey with your findings and corrective action
per Required Action 3 in this Service Bulletin.
Cylinder #1  Exhaust Pipes  Cylinder #2
Cylinder #3
Cylinder #6
Cylinder #5
Examine This Saddle
Reinforced Weld Joint  Exhaust Pipes
Turbocharger Mounting Bracket
Turbocharger  Examine This Saddle
Reinforced Weld Joint  Turbo Oil Drain Tank
Figure 6
Installed Exhaust System
(Cylinders #1, #3, #5 - Right Side of Engine)
Figure 7
Installed Exhaust System
(Cylinders #2, #4, #6 - Left Side of Engine)
Figure 8  Figure 9
Saddle  Saddle
ISSUED  REVISED  PAGE NO  REVISION
MO  DAY  YEAR  MO  DAY  YEAR
3 of 7  C  S.B. 627
07  18  16  11  17  16

### Page 4 (OCR)

D. Examine all cylinder exhaust flanges (Figure
10) for damage, distortion, or signs of exhaust
gas leaking past the gasket, especially at
Cylinder 2. Indications of a flange gasket leak
are burnt paint around the exhaust flange
bosses or powdery white to light brown or
black residue near the leaks, on the spark
plug, and the baffle. If the flange or pipe is
distorted, damaged, or there are signs of
exhaust leaking past the gasket, do not operate
the aircraft until repairs are made in
accordance  with  existing  Lycoming
publications. Complete and submit the survey  Figure 10
with your findings and corrective action per  Signs of Exhaust Leak
Required Action 3 in this Service Bulletin.
WARNING: DO NOT OPERATE THE AIRCRAFT WITH A LEAKING ENGINE EXHAUST
SYSTEM. OPERATION OF THE AIRCRAFT WITH AN EXHAUST SYSTEM
LEAK CAN LEAD TO CARBON MONOXIDE POISONING, LOSS OF
CONCIOUSNESS, INJURY, OR DEATH.
E. Complete a visual inspection on the entire exhaust system (Figures 6 and 7). If any sign of leaks,
distortion, or damage is found, do not operate the aircraft until repairs are made in accordance
with existing Lycoming publications. Complete and submit the survey with your findings and
corrective action per Required Action 3 in this Service Bulletin.
2. Flange Nut Torque Check
A. Since loose flange nuts can be an indication of a potential exhaust leak, complete a torque check
on exhaust system flange nuts for all six cylinders.
B. If a flange, stud, flange nut, or pipe is distorted or visibly damaged, document the issue on the
form then replace with serviceable parts. If it is just a leaky gasket, determine root cause,
document it on the form, and replace the gasket and hardware with new parts. Do not operate the
aircraft until repairs are made in accordance with existing Lycoming publications. Complete and
submit the survey with your findings and corrective action per Required Action 3 in this Service
Bulletin.
C. On the survey, record the fractional amount each flange nut turns to achieve the required 96 in.-
Ib (11 Nm) torque. If any flange nuts are loose enough to allow movement of the washer, contact
Lycoming Engines' Product Support.
3. Submit the completed survey after each Exhaust System Inspection and Flange Nut Torque Check to
Lycoming Engines either online or by mail.
Online  Mail
Fill out the online form at  Copy and manually complete the hard
www.lycoming.com/SB627  copy version of the form in this Service
Click on the link or cut and paste  Bulletin and send it by postal service to:
into your browser.  Technical Support
Lycoming Engines
652 Oliver Street
Williamsport, PA 17701 USA
ISSUED  REVISED  PAGE NO.  REVISION
MO  DAY  YEAR  MO  DAY  YEAR  4 of 7  C  S.B. 627
07  18  16  11  17  16

### Page 5 (OCR)

Engine Serial Number (Ex. L-12345-61E):
Time Since Last Exhaust System Maintenance:
OWNER INFORMATION
Name:
Company:
Address:
City:
State:
Postal Code:
Country:
Telephone Number:
MAINTENANCE PROVIDER INFORMATION
Name:
Company:
Address:
City:
State:
Postal Code:
Country:
Telephone Number:
ISSUED  REVISED  PAGE NO.  REVISION
MO  DAY  YEAR  MO  DAY  YEAR
5 of7  C  S.B. 627
07  18  16  11  17  16

### Page 6 (OCR)

EXHAUST SYSTEM REVIEW
Time Since Exhaust
System Maintenance
Is there an operable  Yes  No
carbon monoxide
detector installed in the
aircraft?
Stamped Data on  Part Number:  Released ID #:  Date Code:
Exhaust Pipe 2
Stamped Data on  Part Number:  Released ID #:
Exhaust Pipe 3
Were any cracks found  Yes  No
on welded joints?
If yes, please describe
the location of the
crack.
Were any exhaust leaks  Yes  No
found at the cylinder
exhaust mounting
flange?
What cylinder exhaust  2  4  5
flange was leaking?
(You may select
multiple cylinders)
Were there any other  Yes  No
exhaust discrepancies
found?
If yes, please describe
the discrepancies found.
ISSUED  REVISED  PAGE NO.  REVISION
MO  DAY  YEAR  MO  DAY  YEAR  6 of 7  C  S.B. 627
07  18  16  11  17  16

### Page 7 (OCR)

Did any exhaust flange nuts require more  Yes  No
turning to reach the required torque?
(96in/Ibs)  Inboard
If yes, which cylinder exhaust flange nuts did you find loose?
Please indicate the amount of movement that you needed to  Outboard  Outboard
tighten the nuts.
CYLINDER 1
N/A  < 1/8 Turn  1/8 Turn  /¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
CYLINDER 2
N/A  < 1/8 Turn  1/8 Turn  ¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
YLINDER 3
N/A  < 1/8 Turn  1/8 Turn  ¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
CYLINDER 4
N/A  <1/8 Turn  / 8 Turn  ¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward  Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
CYLINDER 5
N/A  < 1/8 Turn  1/8 Turn  ¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
CYLINDER 6
N/A  < 1/8 Turn  1/8 Turn  ¼ Turn  ½ Turn  > 1/2 Turn
Forward Outboard Nut
Forward Inboard Nut
Aft Outboard Nut
Aft Inboard Nut
ISSUED  REVISED  PAGE NO.  REVISION
MO  DAY  YEAR  MO  DAY  YEAR
7 of7  S.B. 627
07  18  16  11  17  16

### Page 8

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
