# Lycoming Service Instruction 1238: Revision B

- Rights: © Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2014-0437; AD 2014-23-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lycoming Service Instruction 1238](https://openairdocs.org/service-documents/lycoming/si-1238.md)
- Title as filed: U.S. DOT/FAA - Lycoming Service Instruction 1238B
- Pages: 3
- PDF: https://openairdocs.org/files/sha256/6a/a8/6aa8a65661e648531aa57d39112104c7d6b08768b1255b9f953745774a701806
- Page: https://openairdocs.org/service-documents/lycoming/si-1238/file/6aa8a65661e6

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ISSUED REVISED PAGE NO. REVISION 
MO DAY YEAR MO DAY YEAR 
 04 15 77 01 06 10 1 of 3 B 
 
©2010 by Lycoming  “All Rights Reserved” 
Lycoming Engines, a division of AVCO Corporation, a wholly owned subsidiary of Textron Inc. 
652 Oliver Street 
Williamsport, PA.  17701  U.S.A 
 
Tel. 570-323-6181 
Fax. 570-327-7101 
www.lycoming.com 
 
 
 
DATE: January 6, 2010 Servi ce Instruction No. 1238B 
  (Supersedes Service Instruction No. 1238A) 
  Engineering Aspects are 
  FAA (DER) Approved 
SUBJECT: Assembly and Torque Procedures for V-Band Couplings 
MODELS AFFECTED: Lycoming turbocharged engines. 
TIME OF COMPLIANCE: When assembli ng V-band couplings to the engine. 
V-band couplings are employed by Lycoming on certain ai rframe applications such as the Piper Malibu 
and Saratoga or by other airframe ma nufacturers at various locations in tu rbocharger exhaust systems. They 
are used primarily to seal joints in the exhaust syst em without the necessity for heavy bolted flanges. The 
typical V-band coupling joint consists of the coupling, two flanges and a metal gasket. 
For V-band couplings employed by Lyco ming, a typical example of their in stallation can be found at the 
transition assembly and rear exhaust adapter pipe as  shown in Figure 1. The proper assembly procedure for 
the V-band coupling is as follows: 
 CAUTION 
Proper installation is critical. Tubes and components to be joined must be aligned with each 
other before installation of the V-band couplin g. Flanges must also be aligned correctly 
with zero gap between flange  faces prior to V-band coupli ng installation to ensure good 
joint performance. 
1. Slip V-band coupling (1) over the exhaust adapter pipe (2). 
2. Place the special metal gasket (3) in position with lip of gasket facing exhaust adapter pipe (2). 
NOTE 1 
Anytime a V-band coupling is disassembled, a new gasket must be inst alled at reassembly. 
This will ensure maximum sealing efficiency of the joint. 
3. Join the machined flange of the transition assembly  (4) and the coupling flange of the exhaust adapter 
pipe (2). 
4. With both flanges joined, assemble the V-band coupling (1) over both flanges and the gasket (3). 
SERVICE 
INSTRUCTION

### Page 2

ISSUED REVISED PAGE NO. REVISION 
MO DAY YEAR MO DAY YEAR 
04 15 77 01 06 10 2 of 3 B S.I. 1238 
 
5. Press the V-band coupling (1) over the flanges and engage the latch on the coupling. Using a torque 
indicator wrench, tighten coupling latch nut to a pproximately 70% of torque value. Tap the outer 
surfaces of the coupling with a rubber mallet to distribute the band tension. 
6. Check the torque with wrench, and continue tightening until the specified torque is reached. Repeat as 
in step 5. until torque reading stabilizes. Do not overtorque. 
NOTE 2 
Two types of coupling latch nuts may be f ound on 2.00 inch V-band couplings. A split type 
lock nut, as described with a sp ecified torque of 80 in.-lbs., or a drilled hex. nut secured with 
safety wire, having a torque value of 75 in.-lbs. See Table 1 for additional information. 
TABLE 1 – V-BAND COUPLING TORQUE DATA 
 
Coupling 
Size Tube 
OD 
Lycoming  
Part No. 
Vendor 
Part No. 
V-Band 
Coupling 
Type 
T-Bolt Split 
Type Locknut 
Torque In.-Lbs. 
1/4 Inch Drilled 
Hex. Nut with 
Safety Wire 
Torque In.-Lbs. 
1.00 in. LW-12093-1 MVT69183-100 Spot-Welded 45 -- 
1.25 in. LW-12093-2 MVT69183-125 Spot-Welded 45 -- 
1.50 in. LW-12093-3 MVT69183-150 Spot-Welded 65 75 
1.75 in. LW-12093-4 MVT69183-175 Spot-Welded 65 75 
2.00 in. LW-12093-5 MVT69183-200 Spot-Welded 85 75 
2.25 in. LW-12093-6 MVT69183-225 Spot-Welded 85 75 
2.50 in. LW-12093-7 MVT69183-250 Spot-Welded 85 75 
2.75 in. LW-12093-8 * MVT69183-275 Spot-Welded 85 75 
1.75 in. LW-12125-1 NH1008723-20 Spot-Welded 65 -- 
2.00 in. LW-12125-2 NH1008723-30 Spot-Welded 85 -- 
2.25 in. LW-12125-3 NH1008723-10 Spot-Welded 85 -- 
2.50 in. LW-12125-4 NH1008723-40 Spot-Welded 85 -- 
3.00 in. LW-12125-5 NH1008723-50 Spot-Welded 85 -- 
3.69 in. LW-13464 U4204-55-369M Spot-Welded 70 -- 
3.69 in. LW-15768 NH1004420-10 Spot-Welded 70 -- 
3.30 in. 40D23255-340M NH1009399-10 Riveted 50-60 -- 
3.69 in. 40D22382 NM115002-0225 Spot-Welded 80-90 -- 
3.15 in. 40D22383 NH1008896-10 Spot-Welded 80-90 -- 
3.61 in. 40D23026 NH1009507-10 Spot-Welded 80-90 -- 
 
* - TIO-540-AE2A installations: The latest revision of Service Bulletin No. 492 states that P/N LW-12093-8 
must be removed at the next periodic inspection. Replace with P/N 40D23255-340M.

### Page 3 (OCR)

1 - V-BAND COUPLING RIVETED  TORQUE VALUE FOR THIS
NUT IS IMPORTANT.
SEE STEP 6 AND NOTE 2
1 - V-BAND COUPLING SPOT-WELDED
POSITIVE CLEARANCE
MUST BE EVIDENT
BETWEEN CLAMP
SEGMENTS AFTER
FINAL TORQUE
4 - TRANSITION ASSY. -
2 - EXHAUST ADAPTER PIPE  - 3 - GASKET
LIP OF GASKET MUST FACE
REAR EXHAUST ADAPTER PIPE
Figure 1. Illustrative Example of Exhaust Manifold Gasket and V-Band Coupling Assembly
ISSUED  REVISED  PAGE NO.  REVISION
MO  DAY  YEAR  MO  DAY  YEAR  3 of 3  S.I. 1238
04  15  77  01  06  10

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
