# Lycoming Service Instruction 1343: Revision B

- Rights: © Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2014-0540; AD 2015-02-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lycoming Service Instruction 1343](https://openairdocs.org/service-documents/lycoming/si-1343.md)
- Title as filed: U.S. DOT/FAA - SI 1343B
- Pages: 3
- PDF: https://openairdocs.org/files/sha256/26/0c/260c674e063dee75bebe21402f95ac2e2a91236dc15a982fb092d276919e91d7
- Page: https://openairdocs.org/service-documents/lycoming/si-1343/file/260c674e063d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

652 Oliver Street 
Williamsport, PA.  17701  U.S.A.                  SERVICE
INSTRUCTION
Tel. 570-323-6181 
Fax. 570-327-7101 
www.lycoming.com 
DATE: June 15, 2007 Service Instruction No. 1343B 
(Supersedes Service Instruction No. 1343A) 
Engineering Aspects are 
FAA Approved
SUBJECT: Set Screw for Propeller Governor Idler Shaft 
MODELS AFFECTED: O, IO, LIO, AIO, AEIO-320 Series; O, LO, IO, LIO, AIO, AEIO, TO, TIO-
360 Series; O, IO, AEIO, TIO, LTIO-540 Series; IO-580 Series; IO-720 Wide 
Cylinder Flange Engines that are equipped with a front crankcase mounted 
propeller governor. Wide cylinder flange engines are identified by the suffix 
“A” in the serial number. 
TIME OF COMPLIANCE: At next overhaul. 
   Applicable engines in service that still utilize a P/N MS-9048-111 spring pin to secure the propeller
governor idler shaft must be reworked to incorporate a 10-32 set screw. This is accomplished by drilling and 
tapping the existing spring pinhole as shown in Figure 1. To allow access for peening the set screw in place 
during reassembly, the area around the hole must also be spot faced, if not already accomplished, as shown 
in Figure 2. 
   Engines that are built with the set screw incorporated are assembled with a P/N LW-14021 idler gear 
shaft. Engines that were built with the P/N MS-9048-111 spring pin incorporated a P/N 77876 idler gear 
shaft. Replace P/N 77876 idler gear shaft with a P/N LW-14021 idler gear shaft.  
   Prior to reassembling an engine with damaged th reads in the set screw hole, retap the hole with a 10-32 
UNF-3B, P.D. .1697/.1726 inch tap. If necessary, to insure that there are adequate threads in the set screw 
hole to peen on top of the screw, select a screw that is shorter than the one that was previously removed. 
Refer to Table 1 for the applicable set screw part number and length. 
NOTE
In the following step, a smaller diameter center punch may be used if required to reach the 
top of a shorter set screw. The tip of a center punch utilized by Lycoming personnel for this 
purpose is ground to an approximate 50°/60° included angle. See Figure 3. 
   Assemble the idler gear shaft together with the idler gear and thrust washer and secure the idler gear shaft 
with the setscrew. Insure that the set screw enters the hole in the idler gear shaft before tightening the screw. 
Remove the set screw and apply a light coat of Loctite 290 to the screw. With a clean lint-free cloth, wipe 
away any excess Loctite 290. Install and tighten the set screw to hold the threaded end of the hex head plug 
securely in place within the idler gear shaft. Using a center punch with a 3/32-inch diameter shaft, at the top 
of the tapered point, peen the threads of the hole directly on top of the set screw to prevent the screw from 
backing out. See Figure 3. 
Page 1 of 3 
©2007 by Lycoming  “All Rights Reserved”

### Page 2 (OCR)

Service Instruction No. 1343B
TABLE 1
DESCRIPTION  PART NUMBER
Set Screw - 10-32 x .19 inch long  AN565B1032H3
Set Screw - 10-32 x .25 inch long  AN565B1032H4
Set Screw - 10-32 x .31 inch long  AN565B1032H5
Drill. 159 - 165 inch (No. 20)
Tap No. 10-32 UNF-3B
P.D. : 1697-.1726 inch
>
Figure 1
6885 inch  .6875
If not already accomplished,
3/8 inch dia. spot face,
machine square with drilled
screw hole to dimension shown.
10°
Crankcase Parting
.59 inch +0.01  Surface
SECTION A-A
Figure 2
Page 2 of 3

### Page 3 (OCR)

Service Instruction No. 1343B
Tip has a 50°/60°
included angle.
Example of tool in position
for peening set screw in place.
Peen threads of hole onto
top of set screw to insure
screw will not back out.
Figure 3.
Page 3 of 3

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
