# Lycoming Service Instruction 1391: No revision named

- Rights: © Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2012-0983; AD 2013-10-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Lycoming Service Instruction 1391](https://openairdocs.org/service-documents/lycoming/si-1391.md)
- Title as filed: U.S. DOT/FAA - Lycoming SI 1391
- Pages: 2
- PDF: https://openairdocs.org/files/sha256/e8/2a/e82a7864081de024dd58e7d68710d0dc859fd7559cd1debec434857e9bf35a98
- Page: https://openairdocs.org/service-documents/lycoming/si-1391/file/e82a7864081d

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

TEXTRON Lycoming  SERVICE
652 Oliver Street  Williamsport, PA 17701 U.S.A.  INSTRUCTION
717/323-6181
DATE:  October 5, 1979  Service Instruction No. 1391
Engineering Aspects are
FAA (DER)  Approved
SUBJECT:  Exhaust Manifold Tube Alignment
MODELS AFFECTED:  In0-3d0=8 L-6073-61A.  including  L110-540-F,  models with  serial numbers  models with serial
numbers  up to  including  L-1570-68A.
TIME OF COMPLIANCE:  During engine overhaul or at owner's discretion.
the straight exhaust marred tubes en 17023  with P/N IW-15850  3. In adjusting exhaust manitole tubes, best  tube can be rotated to effect the  alignment. beneficial  See figure 2. In some
tubes have  be replaced by P/N LW-15849. The  a 30 bend which will aid in  exhaust it  nuts one turn to facili-
alignment  of the exhaust manifold tubes  tate  alignment.  alignment has been
transition assembly.  figure 1.  de-tor? cylinders working back to  beginning with
bend tubes.  in the field will accept the  no.  the  assembly. Tighten each at-
part equaily and uniformly until a
ine proceaure  for the installation of the  204 inch pounds has been applied.
tubes  is as follows:
1. Remove Marman clamps from exhaust tubes
on  bo th  sides of the transition assembly.
Remove rear four exhaust tubes.  NOTE
Assemble  exhaust  tubes P/N's IW-  Two types of coupling latch nuts may
and  IW-15850 as indicated in figure  found on 2.00  inch v-band coupli-
1.  ngs. A split type lock nut, as descr-
ibed  with  a  specified torque of 85
If  the  replacement of an exhaust manifold  inch pounds;  Or  a drilled hex nut
component  new gasket should be used at re-assembly.  reguires the removal of a gasket, a  Secue value of 5 inch pren.  secured  with  safety  having a
77023  - 77022
LW-15850  LW-15849
LW-15849  LW-15849-
TI0-540-A,-F  T10-540-J,-R
Figure 1. Exaggerated View Comparing New and Old Tubes
Page 1 of 2

### Page 2 (OCR)

Service Instruction No. 1391
MODIFIED TUBES
TRANSITION
ASSEMBLY
Figure 2. View Showing Alignment of Modified Tube With Transition Assembly
PARTS DATA:
PART NO.  DESCRIPTION  TIO-540  QTY. REQD.
LW-15849  LW-15849  PIPES  PIPE,  Exhaust - left intermediate  Exhaust - right intermediate  A, F, J,R  J,R  1
LW-15850  PIPE, Exhaust - right intermediate  A,F  1
78083  GASKET, V-band coupling - 2.00 OD tube  A, F,J,R  2
LW-15619  GASKET, Exhaust flange  A, F,J,R  12
Page 2 of 2

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
