# M7 Aerospace Service Bulletin CC7-53-005: No revision named

- Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2014-0308; AD 2014-15-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [M7 Aerospace Service Bulletin CC7-53-005](https://openairdocs.org/service-documents/m7-aerospace/cc7-53-005.md)
- Title as filed: CC7 SB 53-005 IR (11-15-13)
- Pages: 26
- PDF: https://openairdocs.org/files/sha256/8f/f2/8ff2700c61ea948db2521ef98a5f61c6303d3f2958dee211e8a897a49c4bf520
- Page: https://openairdocs.org/service-documents/m7-aerospace/cc7-53-005/file/8ff2700c61ea

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421
TO: HOLDERS OF SA227 COMMUTER CATEGORY SERVICE INFORMATION
MANUALS
Attached is SA227 Commuter Category Service Bulletin CC7-53-005, Inspection,
Extended Inspection, and Repair of Fuselage Upper Forward Corner of Main
Cabin Door Cutout , Issued: November 15, 2013.
On aircraft with a bayonet shear pin main cabin door latching mechanism (as
opposed to a "click-clack" latching mechanism), the internal door surround doubler,
the external skin fuselage skin and, in some cases, the door corner fitting have been
found cracked at the fuselage upper forward corner of the main cabin door cutout.
Please insert the attached revised Chapter 53 Index pages.

### Page 2

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421

### Page 3

Issued: January 18, 1993
Revised: November  15, 2013
CHAPTER 53 INDEX
Page 1 of 1
CHAPTER 53 – FUSELAGE
NUMBER DATE TITLE AIRCRAFT EFFECTIVITY
SA227  SERIES
COMMUTER CATEGORY
53-001 01-18-93 Cabin Entrance Door Sill SA227-CC, S/N CC784-853
(R)02-25-93 Beef Up. SA227-DC, S/N DC784-853
53-002 09-22-94 Cockpit Floorboard FOD SA227-CC, S/N CC784, 790-
(R)06-05-96 Barrier Installation 863
SA227-DC, S/N DC784, 790-
863
53-003 09-03-10 Installation of Form-in-Place All SA227 Commuter
Gaskets - Wing-to-Body Category Airplanes
Fairings
53-004 10-08-10 Access Panel Installation All SA227 Commuter
(R)01-26-11 Category Airplanes
53-005 11-15-13 Inspection, Extended All SA227 Commuter
Inspection, and repair of Category Airplanes
Fuselage Upper Forward
Corner of Main Cabin Door
Cutout
53-006 07-27-12 Inspection and/or Replace- All SA227 Commuter
(R)05-13-13 ment of the Left Hand and Category Airplanes
Right Hand Forward and Aft
Wing-to-Body Attach Fittings
53-007 09-26-13 Inspection of F.S. 69.31 All SA227 Commuter
(R)11-06-13 Forward Pressure Bulkhead Category Airplanes
for Cracks

### Page 4

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421

### Page 5

Issued: November 15, 2013 CC7-53-005
Page 1 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FUSELAGE
Inspection, Extended Inspection, and Repair of Fuselage Upper Forward Corner of
the Main Cabin Door Cutout
1. PLANNING INFORMATION
A. Effectivity:
Metro 23, SA227-CC, SN CC827, CC829, CC840 to CC844
Metro 23, SA227-DC, SN DC784, DC790 to DC826, DC828, DC830 to DC839,
     DC845 to DC904
B. Reason:
On aircraft, identified above, with a bayonet shear pin main cabin door latching
mechanism (as opposed to a "click-clack" latching mechanism), the internal door
surround doubler, the external skin fuselage skin and, in some cases, the door
corner fitting have been found cracked at the fuselage upper forward corner of the
main cabin door cutout.
C. Description:
Inspect internal or external skin doubler, fuselage skin, and fuselage door frame
corner member for cracking. If cracks are found, repair steps are included in this
bulletin. If cracks are not  found, the repair doubler/tripler can still be added
extending the inspection intervals.
D. Compliance:
Mandatory
The following initial interval is specified. This interval assumes that the repair
members specified by this bulletin have not been installed.
For aircraft with more than 35,000 Total Aircraft Cycles (TAC), inspect within the
next 300 cycles or 2 calendar months, whichever occurs first, from the date of this
service bulletin.
For aircraft with 20,001 - 35,000 TAC, inspect within the next 600 cycles or 4
calendar months, whichever occurs first, from the date of this service bulletin.
For aircraft  with 12,000 - 20,000 TAC, inspect within the next 1,000 cycles or 12
calendar months, whichever occurs first, from the date of this service bulletin.
For aircraft with less than 12,000 TAC, inspect at 12,000 cycles or within the next
1,000 cycles, whichever occurs later.

### Page 6

Issued: November 15, 2013 CC7-53-005
Page 2 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
Repeat inspection interval for all aircraft is also required.
Inspection Requirements:
Refer to step 2.A. for details.
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
M7 Aerospace estimates the following manhours per aircraft to accomplish the
inspections:
(1) HFEC/LFEC/Detail Visual Inspection - 2.5 hours for threshold inspection.
(2) LFEC with Detail Visual Inspection - 2.0 hours for repeat inspection with inner
doubler cracked.
(3) HFEC with Detail Visual Inspection - 1.5 hours for repeat inspection with intact
inner doubler
(4) Installation of repair - 48 hours.
This estimate is for direct labor only, accomplished by an experienced crew. Adjust
the estimate with operator task hour data if necessary.
G. Material – Cost and Availability:
Contact M7 Aerospace for price and availability. See Step 8. for Material Listing.
Orders need to be placed with M7 Aerospace as there is a lead time on some parts.
H. Tooling – Price and Availability:
The NDT calibration standards (27-02171-001 and 27-02171-021) identified in the
Material Listing, Table 4, are the only specialized tools. The standard, P/N 27-
02171-001, is supplied by M7 Aerospace in the bulletin kit or it can be purchased
separately from M7 Aerospace. The P/N 27-02171-021 standard will be available
from M7 Aerospace at a later date.
Contact M7 Aerospace for price and availability.
I. Weight and Balance:
(1) For inspections only - None.
(2) For installation of the repair kit (P/N 27K24191-001) - 2.5 lbs at F.S. 151. For
installation of skin repair per 27K24191-003, 1.0 lbs at F.S. 130. Update the
AFM Weight and Balance data.

### Page 7

Issued: November 15, 2013 CC7-53-005
Page 3 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
J. References:
M7 Engineering Drawing 27K24191, Rev B (or latest FAA approved revision)
M7 M-5420 Memorandum
M7 Report R1987 - HFEC and LFEC Inspection of Inner Doubler.
M7 Report R2027 - LFEC Inspection of Fuselage Skin.
M7 Aerospace Report No. M07-012-002  (latest FAA approved revision)
M7 Aerospace Report No. M07-013-002  (latest FAA approved revision)
NOTE: References are for manufacturer’s use only.
K. Other Publications Affected:
ST-UN-M003
2. ACCOMPLISHMENT INSTRUCTIONS
This bulletin contains inspections and modifications based upon three scenarios.
Table 1 outlines the basic inspection of this bulletin when complying with the inspection for
the first time. Repeat inspections continue if no cracking is found.
Table 2 outlines the new inspections that must be performed once the repair members for
the kit repair are installed. Installation of the kit does not remove all of the Table 1
inspections. Several of the Table 1 inspections carry over even when the repair members
are installed.
Table 3 offers an option to the operator. It permits the operator to install the repair members
as a preventative measure when no cracking is observed after the first threshold inspection.
These members can be installed at any time after the threshold inspection or follow up
repeat inspections. In many cases, the addition of the repair members to uncracked
structure will result in a new threshold inspection AFTER the aircraft is retired.
Each table identifies figures and bulletin steps detailing the specific inspections to be
performed. It is recommended the operator review the entire bulletin for all applicability.
Each table has several specific notes listed below the table as well as the general notes that
follow this paragraph below.
NOTES:
The expected aircraft configuration for this service bulletin installation is:
No existing repairs are installed or have been performed at this upper forward door surround
corner. If this is not the case and repairs are installed at this location, refer to step 7.

### Page 8

Issued: November 15, 2013 CC7-53-005
Page 4 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
If any of the remaining three corners of the door cutout have a repair or kit drawing
modification installed, this is accommodated within the inspections specified by this bulletin.
See step 2.G.
Definition of Inspections identified in this step:
Detailed Visual Inspection
Inspect using an illumination device (such as circular flourescent inspection lumi-
naire) which produces a minimum of 150 fc of light intensity at the part surface and
a magnification device (such as a watchmaker's loupe) producing approximately 8X
magnification or greater, examine those surface details specified in the inspection
requirements noting defects as directed by the inspection requirements.
Close Visual Inspection
Inspect using an illumination device (such as circular flourescent inspection lumi-
naire) which produces a minimum of 100 fc of light intensity at the part surface and
a magnification device (such as the integral magnifier of the aforementioned
inspection luminaire) producing approximately 1.5X magnification or greater, exam-
ine all surface details of the part noting any obvious defects.
Sub-Surface Inspection - HFEC/LFEC
A subsurface inspection requires calibration. See M7 Aerospace Report R1987 for
inspection procedure and calibration standard (27-02171-001). Both are included in
the kit. Both High Frequency Eddy Current (HFEC) and Low Frequency Eddy
Current (LFEC) are classed as subsurface inspections. Report R2027, which
addresses inspection of the repair members once installed, is not ready at the time
of this bulletin release. Contact M7 Aerospace for a copy when needed.
A. Perform the Threshold (Initial) and Repeat inspection outlined in Table 1:
(1) when complying with this bulletin for the first time per step 1.D. or
(2) continuing the repeat inspections as no cracks have been found and the
operator has elected not to install the repair members per step 6. These
inspections still apply if 27K24191-003 skin repair installation is performed.

### Page 9

Issued: November 15, 2013 CC7-53-005
Page 5 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
NOTES:
<0> Perform these specific service bulletin steps.
<1> Repeat inspection interval assuming no damage or defects found.
TABLE 1
INITIAL INSPECTION
(1) If threshold inspection determines there is an existing repair in the upper
forward corner of the door surround, proceed to step 7.
(2) If crack(s)/damage is found during inspection, go to steps 3., 4., and/or 5. as
applicable depending on component cracked/damaged. Use step 2.B. and
Table 2 for future inspection criteria when repair kit members (27K24191-001)
are installed. Use Table 1 inspection intervals if only skin or corner fitting were
cracked and replaced and no repair doubler is installed. If only skin and fitting
were replaced, it is permissible to install kit per step 6.
(3) If no defect/damage is found, proceed to step 2.H. for aircraft close up or to step
6. when choosing to extend repeat inspection interval.
B. Perform the Threshold and Repeat Inspection outlined in Table 2 when cracks
are found following either the threshold or repeat inspection in Table 1. These
inspections are based on the 27K24191-001 repair members being installed.
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D
> 0 <
E R U G IFD L O H S E R H T
) S E L C Y C (
T A E P E R
) S E L C Y C (
> 1 <
t a r e l b u o d r e n n I
d w F r e p p U
, r e n r o C
, n i k S e g a l e s u F
r e n r o C d n a
g n i t t i F
, l a u s i V l i a t e D
C E F L , C E F H
d n a l a n r e t x E (
l a n r e t n I
) s n o i t c e p s n I
, . E . 2 , . D . 2
) 1 ( . F . 2 5 ,40 0 0 , 210 0 0 , 2
f o s r e n r o C r e h t O
t u o t u C e g a l e s u F
l a u s i V e s o l C
d n a l a n r e t x E (
) l a n r e t n I
. G .26
00 0 , 2 1 0 0 0 , 2

### Page 10

Issued: November 15, 2013 CC7-53-005
Page 6 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
NOTES:
<0> Perform these specific service bulletin steps.
<1> The Table 2 threshold inspection cycles start after the repair doubler in step
3. is installed.
<2> The Table 2 repeat inspection follows the Table 2 threshold inspection once
the repair members are installed.
<3> Continuation of Table 1 repeat inspection on the other three corners of the
cutout if no cracks were found.
TABLE 2
INSPECTION - CRACKED INNER DOUBLER REPAIRED
(P/N 27K24191 KIT INSTALLED)
Maintain this inspection criteria for the duration of the aircraft life. Proceed to step
2.H. for close up.
C. Perform Threshold and Repeat Inspection outlined in Table 3 when the
27K24191-001 repair members have been installed as a preventative measure
per step 6. These inspections assume no cracks exist and that the fuselage skin
Inner Doubler is fully intact (has not been repaired).
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D
> 0 <
E R U G IFD L O H S E R H T
) S E L C Y C (
T A E P E R
) S E L C Y C (
t a n i k S e g a l e s u F
d r a w r o F r e p p U
r e n r o C
C E F L
) l a n r e t x E ( ) 2 ( . F .25
>1 < 0 0 0 , 51> 2 < 0 0 0 , 2
r i a p e R l a n r e t x E
t a r e l b u o D
d r a w r o F r e p p U
r e n r o C
l a u s i V l i a t e D
) l a n r e t x E ( ) 1 ( . D .24 > 1 < 0 0 0 , 51> 2 < 0 0 0 , 2
r i a p e R l a n r e t x E
t a r e l b u o D
d r a w r o F r e p p U
r e n r o C
l a u s i V l i a t e D
) l a n r e t n I ( ) 3 ( . D .27 > 1 < 0 0 0 , 03> 2 < 0 0 0 , 6
f o s r e n r o C r e h t O
t u o t u C e g a l e s u F
l a u s i V e s o l C
d n a l a n r e t x E (
) l a n r e t n I
. G .26
A/N> 3 < 0 0 0 , 2

### Page 11

Issued: November 15, 2013 CC7-53-005
Page 7 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
NOTES:
<0> Perform these specific service bulletin steps.
<1> The Table 3 threshold inspection cycles start after the repair members per
step 3. are installed.
<2> The Table 3 repeat inspection follows the Table 3 threshold inspection.
<3> Continuation of Table 1 repeat inspection on the other three corners of the
cutout if no cracks were found.
<4> An option is available to perform inspection at 20,000 cycles threshold and
6,000 cycles recurring or 30,000 cycles threshold and 3,000 cycles recurring.
The operator can select which option is better suited to their existing
maintenance schedule.
TABLE 3
INSPECTION - INNER DOUBLER NOT CRACKED -
PREVENTATIVE P/N 27K24191 KIT INSTALLED
This option allows the operator to install the repair kit per step 6. even though no
damage/defect was found after the first initial inspection called out in step 1.D. It
extends the next inspection for the forward upper corner from a repeat of every 2,000
cycles to a new threshold of 20,000 cycles (see Note <4>). The other three corners
still require repeat 2,000 hour inspections per step 2.G. Once the kit is installed,
proceed to step 2.H. for close up instructions.
D. Detail Visual Inspection (DVI) (See Figure 4)
(1) External Inspection
Prepare the surface for inspection in accordance with SA227 Commuter
Category Structural Repair Manual (SRM), Chapter 51-30-07. It is not required
to remove surface finish (paint) to perform this inspection. If compounds such
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D
> 0 <
E R U G IFD L O H S E R H T
) S E L C Y C (
T A E P E R
) S E L C Y C (
n i k S r e n n I
t a r e l b u o D
d r a w r o F r e p p U
r e n r o C
C E F H
) l a n r e t x E (. E .25
> 2 < 0 0 0 , 3 > 1 < 0 0 0 , 0 3
R O > 4 <
> 2 < 0 0 0 , 6 > 1 < 0 0 0 , 0 2
f o s r e n r o C r e h t O
t u o t u C e g a l e s u F
l a u s i V e s o l C
d n a l a n r e t x E (
) l a n r e t n I
. G .26 A/ N > 3 < 0 0 0 , 2

### Page 12

Issued: November 15, 2013 CC7-53-005
Page 8 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
as Devcon F or liquid shim are present, which hinder a detail visual inspection,
then these compounds must be removed. Care is required not to remove any
base material of the surface being cleaned.
Perform a detail visual inspection (as defined in step 2) of the forward upper
skin corner fitting, and the visible edge of the inner doubler of the passenger
door cutout at the interval specified in Table 1. Perform this same inspection
on the corner fitting, edge of fuselage skin, repair doubler and tripler once the
27K24191 repair kit has been installed. Inspect for cracks or pulled/loose
fasteners.
(2) Internal Inspection (Kit 27K24191-001 repair members not installed)
Gain access to the interior side of the fuselage skin structure immediately
adjacent to the upper forward corner of the door cutout. This may require
removal of the cabin liner, any interior bulkheads, or cabin furnishings/
monuments. Refer to SA227 Commuter Category  Illustrated Parts Catalog
(IPC), Chapter 25 for components, and SA227 Commuter Category  Mainte-
nance Manual, Chapter 25 for access. Retain all hardware.
Prepare surface for inspection in accordance with SA227 Commuter Category
Structural Repair Manual (SRM), Chapter 51-30-07.
Perform a detail visual inspection (as defined in step 2) of the inner skin doubler
only, around the fasteners shown in the shaded region of Figure 4, at the
interval specified in Table 1. It is not required to remove surface finish (paint/
primer) to perform this inspection. Several fasteners in the actual corner are not
visible due to a gusset blocking the view. It is not required to remove the gusset.
(3) Internal Inspection (Kit 27K24191-001 repair members installed)
Gain access to the interior side of the fuselage skin structure immediately
adjacent to the upper forward corner of the door cutout. This may require
removal of the cabin liner, any interior bulkheads, or cabin furnishings/
monuments. Refer to SA227 Commuter Category  Illustrated Parts Catalog
(IPC), Chapter 25 for components, and SA227 Commuter Category  Mainte-
nance Manual, Chapter 25 for access. Retain all hardware as required.
Prepare the surface for inspection in accordance with SA227 Commuter
Category  Structural Repair Manual (SRM), chapter 51-30-07.
Perform a Detailed Visual Inspection (DVI), as defined in step 2, of the fuselage
skin surface immediately at the peripheral row of fasteners attaching the
external repair doubler to the structure underneath (see Figure 7), at the
interval specified in Table 2. It is not required to remove any surface finish
(paint/primer) to perform this inspection. Several fasteners in the actual corner

### Page 13

Issued: November 15, 2013 CC7-53-005
Page 9 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
are not visible due to a gusset blocking the view. It is not required to remove this
gusset. Inspection is centered on cracking of the fuselage skin and loose/
damaged fasteners.
E. High Frequency Eddy Current (HFEC) Inspection of Inner Doubler Edge
(1) Gain access to exterior edge of the inner doubler at the upper forward corner
of the cutout. Remove any Devcon F or liquid shim material to clearly see the
edge. Perform the inspection in accordance with Kit Report R1987 (NDT Eddy
Current Inspection procedure), HFEC inspection. The inner doubler and
fuselage skin edges are flush with each other. (See Figure 5)
F. Low Frequency Eddy Current (LFEC) Inspection of Inner Doubler and Fuselage
Skin
(1) Inner Doubler: Gain access to exterior surface of the fuselage skin at the upper
forward corner of the cutout immediately around the two rivets as indicated in
Figure 1. Perform the inspection in accordance with Kit Report R1987 (NDT
Eddy Current Inspection procedure), LFEC inspection. This inspects for cracks
emanating around the two rivets, shown in Figures 1 and 5, in the inner doubler.
(2) Fuselage Skin: When performing this inspection after the 27K24191 kit mem-
bers have been installed, the LFEC inspection now inspects the skin with the
probe placed on the tripler surface. Perform inspection using procedure R2027.
Gain access to exterior surface of the tripler at the upper forward corner of the
door cutout. Perform the inspection around the same two rivets shown in Figure
5.
G. Close Visual Inspection of Other Cutout Corners
(1) Applicable to the fuselage skin at lower forward and aft corners and aft upper
corner of the door cutout for the passenger door. (See Figure 6)
(2) Gain access to the exterior fuselage skin around the three corners. If an
external doubler (whether by previous repair or installed by modification kit) is
installed at any of these three corners, perform the Close Visual Inspection of
the external doubler, the skin, and all fastener locations common to both. No
paint/finish is required to be removed to perform this inspection.
(3) Gain access to the interior of the fuselage skin/inner doubler around the three
corners.
(a) This may require removal of interior components such as interior bulkheads,
monuments, seating etc. as well as interior side panels. All hardware shall be
retained unless it is required to be replaced. No paint/finish is required to be
removed to perform this inspection.

### Page 14

Issued: November 15, 2013 CC7-53-005
Page 10 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
(b) Perform a close visual inspection of the inner doubler, adjacent skin, and all
visible fasteners common to both.
(4) Once the inspection is complete, the interior components may be reinstalled.
H. Close Up of Aircraft Following Inspection.
(1) Following any of the inspections outlined in Tables 1, 2, or 3, the interior of the
aircraft can be restored to same condition prior to inspection. Refer to SA227
Commuter Category  Maintenance Manual (MM) and SA227 Commuter Cat-
egory  Illustrated Parts Catalog (IPC) for details.
(a) Reinstall all interior components using retained hardware. Replace hardware
as required.
(b) Restore any surface finishes removed to perform inspection per SA227
Commuter Category  SRM, 51-30-02.
(c) Functionally check any systems disturbed as a result of this inspection per
applicable sections of the SA227 Commuter Category  MM.
(2) Following any of the inspections outlined in Tables 1, 2, or 3, restore exterior
surface finish of the fuselage skin or edge of inner or external doublers, if
required, per SA227 Commuter Category  SRM 51-30-02.
(3) Restore use of Devcon F or liquid shim as previously used prior to inspection
for sealing purpose.
(4) Functionally check any systems that were disturbed as a result of these
inspections in accordance with the applicable sections of SA227 Commuter
Category  Maintenance Manual.
I. Report all cracks/damage to M7 Aerospace at MetroTech@M7Aerospace.com.
Please indicate whether repair was installed due to cracking being found.
The FAA has tasked M7 Aerospace to track the extent of the fleet damage.
J. Complete aircraft records according to 14 CFR 43.9.
K. Complete and return Service Bulletin compliance form to M7 Aerospace
Technical Publications Department.
3. REPAIR OF CRACKED INNER DOUBLER
Repair cracked inner skin doubler per inspection in step 2. The installation of the repair
members is outlined in M7 Aerospace kit drawing 27K24191 (27K24191-001). The crack
damage must be removed prior to installation of repair members in accordance with the
following steps:

### Page 15

Issued: November 15, 2013 CC7-53-005
Page 11 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
A. Determine the end of the crack. Penetrant or HFEC methods in accordance with
SA227 Commuter Category  Structural Repair Manual (SRM) may be used.
B. Trim out the crack in the inner doubler by cutting a slot minimum width 0.25 inch,
end radius 0.25 inch to extend at least 0.030 inch past the end of the crack. If
the crack passes through fasteners. The slot must remove the countersink of
each fastener. Maintain 2D edge distance of any remaining fasteners in the inner
doubler (see Figure 8).
C. Break all sharp edges on the slot cut.
D. Confirm crack has been removed by HFEC inspection of slot per SA227
Commuter Category  Structural Repair Manual (SRM), chapter 51-30-07.
E.  Alodine and prime edge of slot per SA227 Commuter Category  Structural
Repair Manual (SRM), chapter 51-30-02.
F. Fabricate filler for slot using 0.050 inch thick 2024-T3/T42 material with profile to
match slot. Ensure filler is smaller than slot with minimum gap 0.030 inch to
edge of slot. Alodine and prime filler per SA227 Commuter Category  Structural
Repair Manual (SRM), chapter 51-30-02.
G. During installation of repair members 27K24191, locate filler into slot using
sealant per SA227 Commuter Category  Structural Repair Manual (SRM),
chapter 51-30-03, picking up existing fastener pattern.
4. REPAIR OF CRACKED FUSELAGE SKIN
To repair a cracked exterior fuselage skin found in inspection step 2, follow M7 Aerospace
kit drawing 27K24191. If only the skin is cracked and there is no damage to the inner
fuselage doubler, the skin can be replaced per kit installation 27K24191-003. If the skin is
replaced and no other cracks are present, continue to use the inspections per Table 1.
Proceed to step 5 if the corner fitting is cracked, otherwise go to step 2.H. for close up or
return to step 2.A.(2) for further instructions.
5. REPAIR OF CRACKED CORNER FITTING
Replace the cracked corner fitting found in inspection step 2. If the fitting is replaced and
no other cracks are present, continue to use the inspections per Table 1. Refer to ST-UN-
M001, Item 3-5, and the life limit of corner fitting. Life limit on this part remains in effect, but
resets when part is replaced.
6. ADDITION OF KIT DRAWING REPAIR MEMBERS AS PREVENTATIVE ACTION
If following the Table 1 Threshold (initial) inspection or any following repeat inspection
thereafter, and no defect(s)/damage to the inner doubler, the 27K24191-001 kit may be
installed to extend the inspection intervals. For example, if you perform a required

### Page 16

Issued: November 15, 2013 CC7-53-005
Page 12 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
inspection per Table 1, the repeat inspection is now every 2,000 cycles thereafter. However,
the operator can choose to install the 27K24191-001 repair kit to extend the next inspection
out to 30,000 cycles rather than 2,000 cycles. The additional 30,000 cycles, on top of the
current aircraft total cycles at the time of modification may exceed the Limit of Validity
(aircraft life) of 50,000 hours for some operators. Follow the inspection criteria per step 2.C.
to extend the inspection with the repair kit installed.
This step does not apply to those aircraft fitted with the factory installed external fuselage
skin doubler around the periphery of the door cutout.
7. EXISTING REPAIRS ALREADY INSTALLED AT UPPER FORWARD CORNER
For the aircraft effectivity listed in step1.A., if a repair already exists, then the existing repair
most likely will have to be removed if it does not meet the requirements of this service bulletin
kit drawing repair. M7 Aerospace has record of several repairs undertaken by some
operators. It is also probable that there are other repairs in the field that need to be replaced.
M7 Aerospace will work with the operator in determining the best course of action for these
aircraft. Full details of the existing repairs need to be supplied to M7 Aerospace Engineering
to determine the acceptability of the repair. All details including photos, sketches, fuselage
station numbers, BL (buttline) numbers, etc. need to be sent to
MetroTech@M7Aerospace.com or faxed to 210-820-8626.
In lieu of contacting M7 Aerospace with existing repair information, the operator may wish
to replace the existing repair with the service bulletin kit repair, providing the installation is
per the kit repair requirements. Following installation, the step 2.C. inspection criteria are
applicable.

### Page 17

Issued: November 15, 2013 CC7-53-005
Page 13 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
8. MATERIAL LISTING
* Customer Supplied Material
** Only M7 Aerospace supplied kit, including specific part numbers used in the kit,
show compliance with the parts needed for repair.
Any alternate parts not bearing the M7 Aerospace part number and QA stamp
requires approval by M7 Aerospace.
This kit contains the repair kit 27K24191 members, calibration standard, NDT
procedure R1987 and repair drawing 27K24191.
Another kit is being developed to contain the LFEC calibration standard and the
NDT procedure R2027 required for step 2.F.(2). It is currently not available.
TABLE 4
N O I T P I R C S EDR E B M U N T R APY T Q
* * t iK1 0 0 - 3 9 1 4 2 K 721
* e r a w d r aHg n i w a r D t i K e eSR / A

### Page 18 (OCR)

SA227 SERIES  COSPACE
COMMUTER CATEGORY  AN ELBIT SYSTEMS OF AMERICA, LLC, COMPANY
SERVICE BULLETIN
F.S. 126.06  F.S. 133.873
UP
FWD —  ‡= ‡
(Door Opening)
- Probable cracks in
fuselage skin or
external doubler (extending
out from 2 rivets shown)
FIGURE 1
VIEW LOOKING INBOARD AT UPPER FWD DOOR OPENING
CORNER FITTING
FUSELAGE SKIN
INTERNAL DOUBLER
DOOR CORNER  INDICATION OF CRACK IN INTERNAL
FITTING  DOUBLER, ADJACENT TO RIVET
FIGURE 2
VIEW LOOKING AT EDGE OF FUSELAGE DOOR OPENING
Issued:  November 15, 2013  CC7-53-005
Page 14 of 20

### Page 19

Issued: November 15, 2013 CC7-53-005
Page 15 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
DOOR
FRAME
OR
ACLICK-CLACK
BAYONET
FIGURE 3
CLICK-CLACK AND BAYONET LATCHES
(DETAIL A - VIEW SHOWING BAYONET INSTALLED, BUT CLICK-CLACKS
ARE INSTALLED ON EARLIER SERIAL NUMBERS)

### Page 20

Issued: November 15, 2013 CC7-53-005
Page 16 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 4
DETAIL VISUAL INSPECTION AREA OF EXTERNAL
SKIN, EDGE OF INNER DOUBLER AND CORNER FITTING
(SHADED ZONE)
(Door Opening)
UP
FWD
F.S. 126.06 F.S. 133.873

### Page 21

Issued: November 15, 2013 CC7-53-005
Page 17 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
UP
FWD
F.S. 133.873 LFEC Inspection around these 2 rivets
Edge of outer skin, flush with
edge of Inner Doubler
HFEC Inspection of 
Inner Doubler Edge.
Corner Fitting
2.0”
2.0”
FIGURE 5
HFEC AND LFEC INSPECTION AREAS

### Page 22

Issued: November 15, 2013 CC7-53-005
Page 18 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 6
INSPECTION OF OTHER CORNERS OF FUSELAGE CUTOUT
(INSPECT INTERNAL STRUCTURE IN SAME AREA AND LOCATION)
(SHADED REGION TO BE INSPECTED)
VIEW LOOKING INBOARD AT
PASSENGER DOOR OPENING
OUTLINE OF INTERNAL 
PRODUCTION DOUBLER
TYPICAL

### Page 23

Issued: November 15, 2013 CC7-53-005
Page 19 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 7
INTERNAL INSPECTION OF PERIPHERAL ROW OF FASTENERS
ATTACHING REPAIR DOUBLER (27K24191-001)
CANOPY
STRINGER 4
27-24202-001
EXTERNAL DOUBLER
27-24202-003
EXTERNAL DOUBLER
.31 TYP
BL
0.00
FS
126.06
REF 27-22047
HEADER
REF 27-24083
CORNER
UP
FWD
INSPECT FASTENERS AND INNER
SURFACE OF FUSELAGE SKIN IN
SHADED AREAS
STRINGER 5
WINDSHIELD
REF WINDSHIELD
SCREWS
FS
133-873
REF 27-22126
FRAME ASSY
REF 27-20060
INTERNAL GUSSET
STRINGER 1
REF 27-22215
INTERNAL DOUBLER
FS
144.247
FS
(147.17)
FS
(145.95)
FS
148.00
FS
145.12
STRINGER 2
STRINGER 3

### Page 24

Issued: November 15, 2013 CC7-53-005
Page 20 of 20
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 8
CRACK REMOVED BY SLOT TRIMMING
(Door Opening)
Probable cracks in inner
doubler (extending out 
from 2 rivets shown)
Cut slot in Inner Doubler to remove crack with min 0.25 inch radius
at end of crack.  Ensure 2D on remaining Inner Doubler fasteners.
If crack passes through rivets, ensure slot is wide enough to just
remove the countersink in the Inner Doubler. 
UP
FWD
F.S. 126.06 F.S. 133.873

### Page 25

SERVICE BULLETIN COMPLIANCE FORM
CC7-53-005
TO: OPERATOR OR SERVICE FACILITY ACCOMPLISHING BULLETIN
Please complete this compliance form, and  mail according to the instructions on the
reverse side.
Thank you for returning this form.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Aircraft Model Aircraft Serial Number
Bulletin Issue Date Revision Date
Aircraft Registration Number
Operator/Owner
Time on Aircraft
Date Accomplished
Comments

### Page 26

M7 AEROSPACE  LP
P. O. BOX 790490
SAN ANTONIO, TEXAS 78279–0490
(Staple)
ATTN: Service Engineering Department
Fold  Here to Mail
Fold  Here to Mail
Place
Stamp
Here

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
