# M7 Aerospace Service Bulletin CC7-53-007: Revision R1

- Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2013-1057; AD 2014-06-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [M7 Aerospace Service Bulletin CC7-53-007](https://openairdocs.org/service-documents/m7-aerospace/cc7-53-007.md)
- Title as filed: U.S. DOT/FAA - CC7 SB 53-007 R1 (11-06-13)
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/79/2e/792e5a77cc87d811bde7374abb58f1ef0b34f5bdc3673ff6d370f370858cb245
- Page: https://openairdocs.org/service-documents/m7-aerospace/cc7-53-007/file/792e5a77cc87

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421
TO: HOLDERS OF SA227 COMMUTER CATEGORY SERVICE INFORMATION
MANUALS
Attached is Revision 1  to SA227 Commuter Category Service Bulletin CC7-53-007,
Inspection of F.S. 69.31 Forward Pressure Bulkhead for Cracks ,
Issued: September 26, 2013, Revised: November 6, 2013.
Two aircraft have been inspected and found to have significant cracking of the
forward pressure bulkhead between stringers 8 and 10 on both LH and RH sides. The
cracks appear to be adjacent to the horizontal hat stiffeners in the radius of the
bulkhead frame. With the risk of cabin decompression due to cracks in the bulkhead,
this bulletin has been issued to request an immediate inspection of this area.
Revision 1 corrects step 1.D. Change denoted by revision bar in left margin.
Please insert the attached revised Chapter 53 Index pages.

### Page 2

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421

### Page 3

Issued: January 18, 1993
Revised: November  6, 2013
CHAPTER 53 INDEX
Page 1 of 1
CHAPTER 53 – FUSELAGE
NUMBER DATE TITLE AIRCRAFT EFFECTIVITY
SA227  SERIES
COMMUTER CATEGORY
53-001 01-18-93 Cabin Entrance Door Sill SA227-CC, S/N CC784-853
(R)02-25-93 Beef Up. SA227-DC, S/N DC784-853
53-002 09-22-94 Cockpit Floorboard FOD SA227-CC, S/N CC784, 790-
(R)06-05-96 Barrier Installation 863
SA227-DC, S/N DC784, 790-
863
53-003 09-03-10 Installation of Form-in-Place All SA227 Commuter
Gaskets - Wing-to-Body Category Airplanes
Fairings
53-004 10-08-10 Access Panel Installation All SA227 Commuter
(R)01-26-11 Category Airplanes
53-005 00-00-00 Pending All SA227 Commuter
Category Airplanes
53-006 07-27-12 Inspection and/or Replace- All SA227 Commuter
(R)05-13-13 ment of the Left Hand and Category Airplanes
Right Hand Forward and Aft
Wing-to-Body Attach Fittings
53-007 09-26-13 Inspection of F.S. 69.31 All SA227 Commuter
(R)11-06-13 Forward Pressure Bulkhead Category Airplanes
for Cracks

### Page 4

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421

### Page 5

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 1 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FUSELAGE
Inspection of F.S. 69.31 Forward Pressure Bulkhead for Cracks
1. PLANNING INFORMATION
A. Effectivity:
All SA227 Commuter Category Airplanes
B. Reason:
Two aircraft have been inspected and found to have significant cracking of the
forward pressure bulkhead between stringers 8 and 10 on both LH and RH sides.
The cracks appear to be adjacent to the horizontal hat stiffeners in the radius of the
bulkhead frame. With the risk of cabin decompression due to cracks in the bulkhead,
this bulletin has been issued to request an immediate inspection of this area.
Revision 1 corrects step 1.D. Change denoted by revision bar in left margin.
C. Description:
Perform an initial detail visual inspection of the frame flange at F.S 69.31, looking
for cracking in the radius per step 2 instructions. If cracking is found, the operator
is required to contact M7 Aerospace for repair. A repetitive inspection is also
implemented with this bulletin.
D. Compliance:
Mandatory
For aircraft with more than 30,000 flight hours, perform the inspection within the next
150 flight hours from the date of this service bulletin.
For aircraft with 25,000 to 29,999 flight hours, perform the inspection within the next
300 flight hours from the date of this service bulletin.
For aircraft with 20,000 to 24,999 flight hours, perform the inspection within the next
450 flight hours from the date of this service bulletin.
For aircraft with 11,000 to 19,999 flight hours, perform the inspection within the next
600 flight hours from the date of this service bulletin.
For aircraft with less than 11,000 flight hours, perform the inspection at 11,000 flight
hours or within the next 600 flight hours from the date of this service bulletin,
whichever occurs later.
Repeat inspection interval for all aircraft is every 1,000 flight hours following the
initial/threshold inspection.

### Page 6

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 2 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
Inspection requirements: See step 2.
If an owner/operator has evidence to demonstrate that an inspection of FAA
approved equivalent type has been performed within the three previous calendar
months from the date of this bulletin, this shall qualify for the initial/threshold
inspection. If this approved inspection qualifies, then the repeat inspection is every
1,000 hours from the time of that initial/threshold inspection.
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
M7 Aerospace estimates 12 man-hours (for both LH and RH sides) to accomplish
this service bulletin. This includes gaining access via the forward baggage compart-
ment, removing sealant, perform detail visual inspection, and reinstallation This
estimate is for direct labor only, accomplished by an experienced crew. Adjust the
estimate with operator task hour data if necessary.
G. Material – Cost and Availability:
None
H. Tooling – Price and Availability:
No special tooling required.
I. Weight and Balance:
(a) For inspections only - None
(b) For installation of repair, if required. A weight of all repair parts shall be obtained
before installation. These parts are roughly located at F.S. 69.31. The AFM
weight and balance data shall be updated.
J. References:
M7 M-5609 Memorandum.
M7 Engineering Drawing 27-21000 (latest FAA approved revision), F.S. 69.31
bulkhead installation.
M7 Engineering Drawing 27-21028 (latest FAA approved revision), F.S. 69.31
bulkhead assembly.
ST-UN-M003, Item 4-7 bulkhead inspection.
NOTE: References are for manufacturer’s use only.

### Page 7

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 3 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
K. Other Publications Affected:
SA227 Commuter Category Structural Repair Manual (SRM).
ST-UN-M003
2. ACCOMPLISHMENT INSTRUCTIONS
Inspect using an illumination device (such as circular fluorescent inspection luminaire)
which produces a minimum of 150 fc of light intensity at the part surface and a magnification
device (such as a watchmaker's loupe) producing approximately 8X magnification or
greater. Examine those surface details specified in the inspection requirements noting
defects as directed by the inspection requirements.
Inspection requirements for F.S. 69.31: Frame flange between stringers 8 and 10 on both
LH and RH side of the fuselage.
A. Disconnect power to the aircraft and tag out Battery and External Power
switches with placards to prevent injury to personnel or damage to the aircraft.
B. Gain access to the inspection area by removing equipment/liners/insulation in
the forward baggage compartment as required.
NOTE: Depending on aircraft model, this area can have several avionics boxes
mounted as well as the standard baggage bay liners and insulation.
C. Prepare the specific area for inspection by removing sealant and cleaning per
SA227 Commuter Category Structural Repair Manual (SRM), chapter 51-30-02.
D. Perform a Detail Visual Inspection (DVI) of the F.S. 69.31 frame flange, looking
for cracking in the radius of the frame flange. See Figures 1 through 4 for
location of inspection and typical cracks.
E. If cracking is found in radius, continue DVI of surrounding structure including
bulkhead web, and horizontal and vertical web stiffeners, looking for other signs
of damage such as cracking, loose or pulled fasteners.
F. Report all damage to M7 aerospace at MetroTech@M7Aerospace.com or fax to
210-820-8626.
(1) Report specific crack locations, length, and orientation. Send photos or
sketches of all damage. Also please provide Aircraft serial number, total aircraft
hours, and total aircraft cycles.
G. Perform repair in accordance with M7 Aerospace serial number specific FAA
approved Limited Aircraft Repair (LAR) or SRM instructions.
H. If no cracking is found, it is permissible to reseal per SRM 51-30-03 (pressure
boundary).

### Page 8

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 4 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
I. Reassemble/reinstall all equipment/liners/insulation removed in step B. per
applicable sections of the SA227 Commuter Category Maintenance Manual.
J. Remove all placards from Battery and External Power switches and reconnect
power to aircraft.
K. Perform functional/operational checks on all systems that were disturbed per
SA227 Commuter Category Maintenance Manual.
L. Complete aircraft records in accordance with 14 CFR 43.9.
M. Complete and return service bulletin compliance form to M7 Aerospace
Technical Publications Department.

### Page 9

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 5 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 1
FS 69.31 FWD PRESSURE BULKHEAD (27-21028)
Stringer 8L
Stringer 9L
Stringer 10L
Typical cracking
along frame radius
between stringers 8
to 9, and 9 to 10.
LEFT HAND SIDE 
SHOWN
RIGHT HAND SIDE
OPPOSITE
VIEW LOOKING AFT

### Page 10

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 6 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 2
RHS VIEW OF BULKHEAD WITH CRACKS NOTED
(VIEW LOOKING AFT INSIDE FWD BAGGAGE COMPARTMENT)
Stringer 8
Stringer 9

### Page 11

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 7 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 3
LHS VIEW OF BULKHEAD WITH CRACKS NOTED
(VIEW LOOKING AFT INSIDE FWD BAGGAGE COMPARTMENT)
Stringer 9

### Page 12

Issued: September 26, 2013
Revised: November 6, 2013
CC7-53-007 R1
Page 8 of 8
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
FIGURE 4
TYPICAL CRACK LOCATION
(VIEW WITH EXTERNAL FUSLAGE SKIN REMOVED)
CRACK

### Page 13

SERVICE BULLETIN COMPLIANCE FORM
CC7-53-007 R1
TO: OPERATOR OR SERVICE FACILITY ACCOMPLISHING BULLETIN
Please complete this compliance form, and  mail according to the instructions on the
reverse side.
Thank you for returning this form.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Aircraft Model Aircraft Serial Number
Bulletin Issue Date Revision Date
Aircraft Registration Number
Operator/Owner
Time on Aircraft
Date Accomplished
Comments

### Page 14

M7 AEROSPACE  LP
P. O. BOX 790490
SAN ANTONIO, TEXAS 78279–0490
(Staple)
ATTN: Technical Publications Department
Fold  Here to Mail
Fold  Here to Mail
Place
Stamp
Here

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
