# Fairchild Service Bulletin 226-27-061

Copy: No revision named ("SB 226-27-061"), 9 pages: PDF https://openairdocs.org/files/sha256/e8/0b/e80bb07dae43faea4a06f4f240776ef2e7fd3ec4f353338be1176749a55690d6; text https://openairdocs.org/service-documents/m7-aerospace/sb-226-27-061/file/e80bb07dae43.md. Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2015-2207, the docket of AD 2015-19-10. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Fairchild](https://openairdocs.org/service-documents/m7-aerospace.md)
- Type: Service bulletin (Service Bulletin)
- Number: 226-27-061
- Page: https://openairdocs.org/service-documents/m7-aerospace/sb-226-27-061

## Text (9 pages)

Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2015-2207, the docket of AD 2015-19-10. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Issued: June 16, 1997 226-27-061
Page 1 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
Flight Controls
Control Column Pivot Improvement
1. PLANNING INFORMATION
A. Effectivity:
All SA226 Series Airplanes
B. Reason:
To provide operators with an improved control column pivot design that adds strength
as well as maintainability to the installation.
C. Description:
Replace existing CF-5/8-S roller bearing, 26-21352 doubler with new 27-21169 control
column pivot. Inspect existing 26-21065 bracket for cracks, remove and replace bracket
if cracks are found.  The new pivot consists of a 27-21169-007 fitting which is provided
undrilled (fastener holes to be picked up from old doubler) , a KRJ8-UDYB-016  bearing
(KARON) is installed in the fitting with LOCTITE 609, and 27-21169-005 pin is installed
in the existing bearing cup on the control column, pin installation is accomplished by
match drilling the bearing cup to the pin through-hole (SAT1518 tool jig available) and
installing  spring pin and safety wire.
NOTE: Kit A will include SAT1518 tool jig, control column, and Kit B will include
parts for one ship set.
D. Compliance:
Highly Recommended, accomplish at next scheduled access, in conjunction with Phase or
Letter Check Inspection.
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
It is recommended that owners obtain an estimate from their nearest Fairchild Aircraft (FA)
authorized Service Facility/Maintenance Department.

### Page 2

Issued: June 16, 1997 226-27-061
Page 2 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
G. Material-Cost and Availability:
(1) Cost:
Because of pricing fluctuations, individual cost estimates should be obtained from your
normal material procurement outlet.
Additional material cost information may be contained in the Index or the Letter of
Transmittal.
(2) Availability:
Parts are available.
H. Tooling-Price and Availability:
No special tooling required.
I. Weight and Balance:
Increase (+) weight 0.16 pound, increase (+) moment 15.37 inch-pounds.
J. Reference:
Fairchild Aircraft (FA) Drawing 26-71004, 26-21352, 27-21000 and 27-21169.
NOTE: References are for manufacturers’ use only.
K. Other Publications Affected:
SA226 Series Illustrated Parts Catalog (IPC) and Maintenance Manual (MM).

### Page 3

Issued: June 16, 1997 226-27-061
Page 3 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
2. ACCOMPLISHMENT INSTRUCTIONS
A. Removals
NOTE: Surface finish of bare metal, surface cleaning, fastener hole drilling, coun-
tersinks, deburring and fastener installation shall be accomplished as
described in SA226/227 Series Structural Repair Manual (SRM) Chapter
51, unless otherwise noted. Clamp and/or Cleco all parts as they are drilled
to prevent part shifting.
(1) Remove cockpit furnishings and floorboards as required to gain access to Pilots
(LH) and Copilots (RH)control column roller bearings.
(2) Remove existing LH/RH CF-5/8-S control column roller bearing and 26-21352 doubler,
scrap attaching hardware.
NOTE: Make note of washer stack up between LH/RH roller bearing and doubler,
these washers were used for shims and the same number of AN960C816
and/or AN960C816L washers will need to be installed between new
KRJ8-UDYB-016 bearing and head of 27-21169-005 pin to maintain
control column position on final installation.
NOTE: Removed LH/RH 26-21352 doubler(s) will be used to pick up fastener
holes on new LH/RH 27-21169-007 fitting and should be marked on
removal to avoid confusion (LH, RH, up, down, forward, aft, inboard,
outboard).
(3) Inspect LH/RH 26-21065 bracket for cracks, no cracks allowed.  Remove and
replace LH/RH 26-21065 bracket if cracks are found.
(4) Remove LH/RH roller bearing and nutplates from 26-21352 doubler, retain roller
bearing attaching hardware and scrap nutplates.
(5) Install roller bearing on opposite side of 26-21352 doubler using previously
removed hardware, as shown in FIGURE 1.
(6) Push LH/RH roller bearing into bearing hole of LH/RH 27-21169-007 fitting from
inboard side (flat side), align so that top of 26-21352 doubler is parallel to top
of fitting and clamp as required to prevent movement during drilling.
(7) Using the existing fastener holes in LH/RH 26-21352 doubler as guides, d rill
0.190 to 0.194 inch diameter hole through LH/RH 27-21169-007 fitting (inner
attach holes), 4 places, as shown in FIGURE 1.
(8) Remove clamp from LH/RH 27-21169-007 fitting.  Scrap LH/RH 26-21352
doubler, bearing and attaching hardware.

### Page 4

Issued: June 16, 1997 226-27-061
Page 4 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
(9) Layout and drill 0.190 to 0.194 inch diameter hole through LH/RH 27-21169-007
fitting (outer attach holes), 4 places, as shown in FIGURE 2.  Deburr holes, 8
places.
(10) Enlarge existing bearing through-hole in LH/RH 26-21065 bracket, as shown in
FIGURE 1.
(11) Temporarily place new KRJ8-UDYB-016 bearing in LH/RH 27-21169-007 fitting
and check for proper fit in LH/RH 26-21065 bracket.
NOTE: It is permissible to remove a maximum of two (2) rivets if their location
interferes with top of fitting or bearing, rivet hole(s) may be left open.
(12) Remove KRJ8-UDYB-016 bearing from LH/RH 27-21169-007 fitting.
(13) Temporarily install LH/RH 27-21169-007 fitting and using outer fastener holes
in fitting as guides, drill 0.190 to 0.194 inch diameter hole through LH/RH
26-21065 bracket, 4 places.
(14) Remove LH/RH 27-21169-007 fitting and deburr holes in LH/RH 26-21065
bracket, 4 places.
(15) Locate SAT1518 tool jig onto LH/RH 26-71004 bearing cup on control column,
tighten at desired position (0 ° to 90°) and drill 0.125 to 0.129 inch diameter hole
through both sides of cup, as shown in FIGURE 2.
(16) Remove tool jig and deburr holes.
(17) Repeat Steps 2.A. (2) through (16) for opposite side.
B. Installation
(1) Locate MS21073L3 nutplate on outboard side of LH/RH 27-21169-007 fitting,
8 places and drill 0.097 to 0.102 inch diameter hole, 2 places each nutplate,
deburr holes, 16 places.  Countersink inboard side of nutplate fastener holes,
100° x 0.175 to 0.183 inch diameter, 16 places, as shown in FIGURE 2.
(2) Install MS21073L3 nutplate, using 2 each, MS20426AD3-( ) rivets on outboard
side of LH/RH 27-21169-007 fitting, 8 places, as shown in FIGURE 2.
(3) Clean bearing hole of LH/RH 27-21169-007 fitting and KRJ8-UDYB-016 bearing,
install bearing from flat side of fitting, using LOCTITE 609.
(4) Install LH/RH 27-21169-005 pin into LH/RH bearing cup, align bearing cup/pin
holes, install MS171532 spring pin and safety in accordance with MS33540
using MS20995C32 lockwire.

### Page 5

Issued: June 16, 1997 226-27-061
Page 5 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
(5) Install required stack up of AN960C816 and/or AN960C816L washers (deter-
mined in Step 2.A. (2) Note) onto LH/RH 27-21169-005 pin.
(6) Position LH/RH 27-21169-007 fitting onto LH/RH 27-21169-005 pin, install 8
each AN3-4A bolts and AN960-10L washers.
(7) Repeat Steps 2.B. (1) through (6) for opposite side.
(8) Perform elevator functional check, as described in SA226 MM.
(9) Replace all cockpit furnishings and floorboards removed to accomplish this
inspection/replacement.
C. Complete aircraft records according to F.A.R. 43.9.
D. Complete and mail Service Bulletin compliance form.

### Page 6

Issued: June 16, 1997 226-27-061
Page 6 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
3. MATERIAL LISTING
Replacement or alternate parts approved via Fairchild Aircraft drawings are acceptable
substitutes for use in accomplishing this bulletin.
The following materials are required to accomplish the instructions outlined in this service
bulletin. SB226-27-061 Kit A or B can be ordered and will contain all materials listed except
common stock items which may be obtained locally or ordered separately.
KIT A - Contains SAT1518 Tool Jig, Control Column.
NEW P/N QTY. KEYWORD OLD P/N DISPOSITION
SAT1518 1 Tool Jig, N/A N/A
Control Column
226-27-061-PL-A 1 Packing List N/A N/A
KIT B - Contains Parts for One Ship Set, Except Common Stock Items.
NEW P/N QTY. KEYWORD OLD P/N DISPOSITION
27-21169-007 2 Fitting 26-21352-001, Scrap
-005, -007 or -007P
27-21169-005 2 Pin CF-5/8-S Scrap
AN3-4A * 16 Bolt AN3-5A Scrap
AN960-10L * 16 Washer AN960-10L Scrap
AN960C816 * A/R Washer AN960C416 Scrap
AN960C816L * A/R Washer AN960C416L Scrap
KRJ8-UDYB-016 § 2 Bearing N/A N/A
MS171532 2 Spring Pin N/A N/A
MS21073L3 * 16 Nutplate N/A N/A
MS20426AD3-( ) * 32 Rivet MS20426AD3 Scrap
609 * A/R LOCTITE N/A N/A
226-27-061-PL-B 1 Packing List N/A N/A
* Indicates materials are common stock items which will not be included in the kit.
These parts may be obtained locally or ordered separately.
§ Indicates KAMATICS Part Number.

### Page 7

Issued: June 16, 1997 226-27-061
Page 7 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
CONTROL COLUMN IMPROVED PIVOT
INSTALLATION INSTRUCTIONS
FIGURE 1
26B270471
EXISTING 26-21352-001/-005/-007 OR -007P DOUBLER ASSEMBLY
EXISTING 26-21352-001/-005/-007 OR -007P DOUBLER ASSEMBLY
FWD INBD
(1) REMOVE CF-5/8-S ROLLER BEARING AND 4 NUTPLATES, IF INSTALLED, FROM
     26-21352 DOUBLER.
(2) INSTALL ROLLER BEARING ON OPPOSITE SIDE OF DOUBLER.
(3) POSITION DOUBLER ONTO INBOARD SIDE OF NEW 27-21169-007 FITTING.
(4) CLAMP DOUBLER AND FITTING TOGETHER, MATCH DRILL FITTING,
     0.190 TO 0.194 INCH DIAMETER HOLE, 4 PLACES, USING EXISTING FASTENER
     HOLES IN DOUBLER AS GUIDE.

26-21352 DOUBLER
(1) (2) (3) (4)27-21169-007 FITTING
INCREASE EXISTING 0.750 INCH DIAMETER
HOLE TO 1.00 INCH DIAMETER HOLE.
COPILOTS SIDE, LOOKING OUTBOARD
(PILOTS SIDE OPPOSITE)
COPILOTS SIDE, LOOKING FORWARD
(PILOTS SIDE OPPOSITE)
COPILOTS SIDE, LOOKING DOWN
(PILOTS SIDE OPPOSITE)
FWD
COPILOTS SIDE, LOOKING OUTBOARD
(PILOTS SIDE OPPOSITE)
FWD
EXISTING FASTENERS THAT INTERFERE WITH
27-21169-007 FITTING MAY BE REMOVED AND
HOLES LEFT OPEN, (2 MAXIMUM).
INSPECT 26-21065 BRACKET FOR
CRACKS. IF ANY CRACKS ARE FOUND,
REMOVE AND REPLACE BRACKET.

### Page 8

Issued: June 16, 1997 226-27-061
Page 8 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
CONTROL COLUMN IMPROVED PIVOT
INSTALLATION INSTRUCTIONS
FIGURE 2
26B270472
COPILOTS CONTROL COLUMN
(PILOTS SIDE OPPOSITE)
A
DETAIL A
(PILOTS SIDE OPPOSITE)
FWD
DRILL 0.125 TO 0.129 INCH DIAMETER HOLE
THROUGH CUP, USING SAT1518 TOOL JIG.
CAN BE CLOCKED FROM 0° TO 90° AS REQUIRED.

0° TO 90°
27-21169-005 PIN
AN960C816 AND/OR
AN960C816L WASHER(S)
QUANTITY AS REQUIRED
FOR SHIMMING.
AN3-4A BOLT
AN960-10L WASHER
8 PLACES
27-21169-007 FITTING
SHOWN WITH,
KRJ8-UDYB-016 BEARING
INSTALLED.
MS21073L3 NUTPLATES
OMITTED FOR CLARITY.
INSTALL MS171532 SPRING PIN,
SAFETY USING MS20995C32
LOCKWIRE.
B
B C
CINSPECT 26-21065 BRACKET
FOR CRACKS. IF ANY CRACKS
ARE FOUND, REMOVE AND
REPLACE BRACKET.

### Page 9

Issued: June 16, 1997 226-27-061
Page 9 of 9
SERVICE BULLETIN
AIRCRAFTSA226 SERIES
CONTROL COLUMN IMPROVED PIVOT
INSTALLATION INSTRUCTIONS
FIGURE  2, VIEW B-B AND C-C
6B270612B
VIEW C-C
27-21169-007 FITTING
COPILOTS SIDE - LOOKING INBOARD
(PILOTS SIDE OPPOSITE)
VIEW B-B
COPILOTS SIDE - LOOKING OUTBOARD
(PILOTS SIDE OPPOSITE)
FWD
FWD
1.345 INCH
1.345 INCH
27-21169-007 FITTING

DRILL 0.097 TO 0.102 INCH
DIAMETER HOLE, 2 PLACES
EACH NUTPLATE.
COUNTERSINK FAR SIDE OF
FITTING, 100° X 0.175 TO 0.183
INCH DIAMETER, 16 PLACES.
INSTALL MS21073L3 NUTPLATE
ON NEAR SIDE OF FITTING,
USING 2 EACH, MS20426AD3-( ),
8 PLACES.
DRILL 0.190 TO 0.194 INCH
DIAMETER HOLE, 8 PLACES
(4 PLACES MATCH DRILLED
TO 26-21352 DOUBLER).
26-21352 DOUBLER
(SHOWN FOR REFERENCE
ONLY)
KRJ8-UDYB-016 BEARING
INSTALL FROM
FAR SIDE, USING
LOCTITE 609.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
