# M7 Aerospace Service Bulletin 226-27-081

Copy: Revision R1 ("226-27-081 R1"), 14 pages: PDF https://openairdocs.org/files/sha256/09/9a/099ae9a88744bd828dc4b83e4cf0353553cf96053b1b2d51ff79f4078539801a; text https://openairdocs.org/service-documents/m7-aerospace/sb-226-27-081/file/099ae9a88744.md. Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2016-9120; AD 2016-25-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Fairchild](https://openairdocs.org/service-documents/m7-aerospace.md) (issued as M7 Aerospace)
- Type: Service bulletin (Service Bulletin)
- Number: 226-27-081
- Latest revision known: 226-27-081, Revision R1, dated June 27, 2016 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/m7-aerospace/sb-226-27-081

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-25-12](https://openairdocs.org/ad/2016-25-12.md), effective Jan 12, 2017: Revision R1

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/m7-aerospace/sb-226-27-081/proposed.md).

## Text (14 pages)

Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2016-9120; AD 2016-25-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

10823 NE Entrance Road • San Antonio, Texas 78216-6001 • (210) 824–9421
TO: HOLDERS OF SA226 SERIES SERVICE INFORMATION MANUALS
Attached is SA226 Series Service Bulletin 226-27-081, Pitch Trim Actuator Upper Attach 
Fittings Inspection, Issued: April 13, 2016; Revised: June 27, 2016.
An operator reported stress corrosion cracks on pitch trim actuator upper attach ﬁ ttings in 
the bolt holes and in the web radii of the ﬁ ttings.
This Service Bulletin removes and performs an initial detailed visual inspection, liquid 
penetrant inspection (LPI) and  high frequency eddy current (HFEC) inspection of the upper 
pitch trim actuator attach ﬁ ttings for cracking in the bolt holes and the web/ﬂ ange radius.
This revision deﬁ nes compliance requirement in step 1.D. if previous revision of this service 
bulletin was complied with, clari ﬁ es steps 2.A.6)b) and 2.B.1), changes "as" to "or" in 
second note under 2.A.6)d), adds alternative parts to 3. Material Listing and adds Figure 
3 to show bushing location and orientation.
Please replace the Service Bulletin and Chapter 27 Index pages.

### Page 2

P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421

### Page 3

CHAPTER 27 – FLIGHT CONTROLS
CHAPTER 27 INDEX
Page 7 of 8
NUMBER DATE TITLE AIRCRAFT EFFECTIVITY
SA226 SERIES INDEX
27-060  12-11-96 Control Column Roller Bearing All SA226 Series Airplanes
 (R) 02-24-97 and Elevator Rod End Bearing
 (R) 12-05-14 Inspection/Replacement
27-061  06-16-97 Control Column Pivot All SA226 Series Airplanes
   Improvement
27-062  11-18-98 Installation of Simmonds All SA226 Series Airplanes
   Precision P/N DL5040M5 with Barber Colman, P/N
   and/or DL5040M6 Pitch Trim 27-19008-001/-002 Pitch
   Actuator (PTA) Trim Actuator Installed.
27-063  05-11-99 Installation of P/N  All SA226 Series Airplanes
 (R) 12-27-99 DL5040M8, Simmonds with P/N 27-19008-001/-002/
 (R) 11-18-02 Precision Pitch Trim -004/-005/-006/-007 Bar 
   Actuator (PTA) ber-Colman PTA Installed.
27-064  03-08-99 Installation of All SA226 Series Airplanes
   27-19008-006/-007 with P/N 27-19008-001/-002/
   Barber-Colman Pitch Trim -004/-005 Barber-Colman  
   Actuator (PTA Installed. PTA
27-065  12-05-00 Installation of Fairleads All SA226 Series AT and TC
   at F.S. 174.06 Airplanes
27-066  09-29-03 Life Limit for Rudder Gust All SA226 Series Airplanes
   Lock Assembly, Part Number
   27-70066-001, of 5000 Hours
27-067  04-02-04 Inspection of 26-72003 Rudder All SA226 Series Airplanes
   Pedals for cracks
27-068   NOT ISSUED
27-069   NOT ISSUED
27-070  09-19-08 Gravel Guard Installation All SA226 Series Airplanes
27-071  04-28-09 Pilot's and Copilot's Control All SA226 Series Airplanes
   Column Access Panels 
   Modi ﬁ cation
27-072  06-27-11 Flight Control Cable SA226-T, S/N T265, T267 
   Replacement SA226-T(B), S/N T(B)348 
    SA226-TC, S/N TC277  
    SA226-AT, S/N AT071,   
    AT072, AT073  
27-073  06-10-11 Inspection and Repair /  All SA226 Series Airplanes
 (R) 09-06-11 Replacement of Pitch Trim      
 (R) 10-14-11 Actuator Fuselage Fittings      
Issued: February 8, 1971
Revised: April 13, 2016

### Page 4

CHAPTER 27 – FLIGHT CONTROLS
NUMBER DATE TITLE AIRCRAFT EFFECTIVITY
SA226 SERIES INDEX
CHAPTER 27 INDEX
Page 8 of 8
Issued: February 8, 1971
Revised: June 27, 2016
27-074  06-06-13 Inspection and Lubrication of All SA226 Series Airplanes 
 (R) 09-30-13 the Aileron Control Cable       
 (R) 10-23-13 Chain in the Pilot's and Co-      
   Pilot's Control Columns
27-075  09-04-14 Inspection/Replacement of the All SA226 Series Airplanes 
   Aileron Control System Rod       
   End Bearings
27-076  09-04-14 Inspection of the Aileron Link All SA226 Series Airplanes 
   Rod, Bellcrank, and Aileron      
   Hinge Bracket for Damage
27-077  08-18-14 Inspection/Repair of Wiring All SA226 Series Airplanes 
   Harnesses in the Vertical      
   Stabilizer
27-078  10-08-15 Inspection of Cockpit Control All SA226 Series Airplanes
   Column Horizontal Tube for
   Cracks
27-079  04-23-15 Inspection of Rudder Bellcrank All SA226 Series Airplanes 
 (R) 09-21-15
 (R) 10-12-15
27-080  11-05-15 Inspection of the Elevator All SA226 Series Airplanes 
 (R) 02-23-16 Control System Rod End
   Bearings
27-081  04-13-16 Pitch Trim Actuator Upper All SA226 Series Airplanes
 (R) 06-27-16 Attach Fittings Inspection

### Page 5

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 1 of 8
SERVICE BULLETIN
SA226 SERIES
FLIGHT CONTROLS
PITCH TRIM ACTUATOR UPPER ATTACH FITTINGS INSPECTION
1. PLANNING INFORMATION
A. Effectivity:
All SA226 Series Airplanes.
B. Reason:
An operator reported stress corrosion cracks on pitch trim actuator upper attach ﬁ ttings 
in the bolt holes and in the web radii of the ﬁ ttings.
This revision de ﬁ nes compliance requirement in step 1.D. if previous revision of this 
service bulletin was complied with, clari ﬁ es steps 2.A.6)b) and 2.B.1), changes "as" 
to "or" in second note under 2.A.6)d), adds alternative parts to 3. Material Listing and 
adds Figure 3 to show bushing location and orientation. 
C. Description:
Remove and perform an initial detailed visual inspection, liquid penetrant inspection 
(LPI) and high frequency eddy current (HFEC) inspection of the upper pitch trim actuator 
attach ﬁ ttings for cracking in the bolt holes and the web/ﬂ ange radius.
D. Compliance:
Mandatory.
Initial Inspection: Recommended as soon as possible and no later than 600 ﬂ ight hours, 
or 12 calendar months, whichever occurs ﬁ rst, from the date of this bulletin.
Repeat Inspection: Continue to repeat inspect upper pitch trim actuator attach ﬁ ttings 
IAW step 2. Accomplishment Instructions in this bulletin every 5,000 ﬂ ight hours or 5 
calendar years, whichever occurs ﬁ rst from the date of this service bulletin.
If steps 2.A.6)c) through 2.A.6)e) AND steps 2.B and 2.C were complied with per the 
initial issue of this service bulletin, the initial inspection requirement of this service 
bulletin is considered to be satis ﬁ ed. Otherwise, additional compliance with this R1 
revision of the service bulletin is required.
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
M7 Aerospace estimates 16 manhours to perform the initial inspection which includes 
removal and installation. This estimate is for direct labor only accomplished by an 
experienced crew. Adjust the estimate with operator task hour data as necessary.

### Page 6

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 2 of 8
SERVICE BULLETIN
SA226 SERIES
G. Material - Cost and Availability:
Contact M7 Aerospace Spares/Sales Department for Cost and Availability.
H. Tooling-Price and Availability:
Refer to the SA226 Maintenance Manual (MM) for required tooling for rigging of pitch 
trim control system if necessary. 
I. Weight and Balance:
Negligible.
NOTE: It is recommended the aircraft operating weight be re-established after 
incorporating 20 service bulletins classi ﬁ ed as having negligible impact on 
aircraft weight and balance. This recommendation is derived from data provided 
in FAA Advisory Circular 120-27.
J. Reference:
M7 Aerospace SDR Review Item;
SA226 Maintenance Manual, 27-40-02;
SA226 Illustrated Parts Catalog (IPC) 27-40-02, Figure 1.
NOTE:  References are for manufacturers’ use only.
K. Other Publications Affected:
ST-UN-M002 Airframe Airworthiness Limitations Manual.
2. ACCOMPLISHMENT INSTRUCTIONS
A. Removals and Inspection:
1) Position horizontal stabilizer full leading edge up for easier access to pitch trim 
actuator (PTA) upper attach ﬁ ttings.
2) Remove electrical power from the aircraft. Disconnect main batteries and Ground 
Power Unit (GPU). Tag out breakers and switches to prevent injury to personnel 
or damage to the aircraft.
3) Placard cockpit pitch trim controls " DO NOT USE" to prevent damage to aircraft 
or injury to personnel.
4) Gain access to PTA upper attach ﬁ ttings.
5) Mark the upper attach ﬁ ttings with their position (LH or RH) and mark their lateral/
vertical location on the stabilizer spar to ensure the same rod end to ﬁ tting lug 
alignment is maintained when reinstalled.

### Page 7

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 3 of 8
SERVICE BULLETIN
SA226 SERIES
WARNING: DISCONNECTING BOTH PTA ROD ENDS FROM UPPER 
ATTACH FITTINGS WILL ALLOW HORIZONTAL STABILIZER 
TO PIVOT WITHOUT RESTRAINT AND MAY CAUSE INJURY TO 
UNSUSPECTING PERSONNEL AND/OR DAMAGE TO AIRCRAFT 
STRUCTURE OR COMPONENTS. CARE MUST BE TAKEN TO 
SUPPORT LEADING EDGE OF STABILIZER WHILE PTA IS 
DISCONNECTED FROM STABILIZER.
NOTE:  The following instructions require removal of the ﬁ ttings from the stabilizer 
spar. It is permitted to perform these inspections with ﬁ ttings still installed 
provided operator/technician has the access to perform the inspection 
correctly, i.e., one bolt may be removed at a time and hole inspected, 
etc.
NOTE: It is recommended to remove one ﬁ tting at a time as this aids installation.
6) The following instructions apply to both upper attach ﬁ ttings:
a) Remove hardware securing PTA rod end to upper attach ﬁ tting (See Figure 
1). Inspect hardware for condition and replace as required.
b) Remove hardware securing upper attach ﬁ tting to horizontal stabilizer and 
remove ﬁ tting from stabilizer (See Figure 1). Inspect hardware for condition 
and replace as required. Bushings do not need to be removed. If aircraft 
records show Service Letter 226-SL-031 has been complied with and ﬁ ttings 
have not been replaced since compliance, proceed with the following steps. 
Otherwise, inspect each side of the ﬁ tting lugs IAW 226-SL-031 in conjunction 
with the following inspections.
c) Detail visual inspect for cracks and corrosion over entire surface of ﬁ tting 
using good light (100 fc minimum).
d) Perform a liquid penetrant inspection (LPI) of the ﬁ tting radius area for cracks 
in accordance with SA226/227 Structural Repair Manual (SRM) Chapter 51-
30-07 (See Figure 2 for inspection areas).
NOTE: Liquid penetrant inspection requires removal of primer/paint and 
cleaning of surface.
NOTE: It is permissible to substitute HFEC or ultrasonic inspection method 
IAW SRM 51-30-07 in lieu of LPI.
e) Perform a high frequency eddy current (HFEC) inspection of the ﬁ tting to 
stabilizer bolt holes (4 off per ﬁ tting) shown in Figure 1 in accordance with 
SA226/227 SRM, Chapter 51-30-07 (See Figure 2 for inspection areas).
NOTE: The ﬁ tting is fabricated from a 2000 series aluminum alloy.
NOTE: A manual or rotary hole probe method for each hole is acceptable 
(Probe must be capable of detecting ﬂ aw sizes ≤ 0.030 inch (0.762 
mm)).

### Page 8

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 4 of 8
SERVICE BULLETIN
SA226 SERIES
B. Installation:
1) If any cracks or corrosion are found, replace the attach ﬁ tting (Refer to step 3. 
Material Listing for correct replacement part numbers):
a) If installing 27-43062-011R or -019R ﬁ tting (without bushings installed), 
refer to Figure 3 for bushing location and orientation. If necessary, line ream 
bushing holes in ﬁ tting to 0.4380/0.4385 inch (11.125/11.138mm) diameter 
and install bushings wet with primer IAW SA226/227 SRM Chapter 51-30-02.
b) Match drill ﬁ tting with 4x attach holes 0.250/0.254 inch (6.35/6.45 mm) diameter 
to holes in stabilizer spar, ensuring the ﬁ tting is located in the same position 
as marked on spar in step 2. A. 5).
c) Re-identify ﬁ tting with drilled assembly part number determined in step 2.B.1) 
minus the "R" (i.e., 27-43062-013 or -015).
d) Proceed to step 2.B.3).
2) If no cracks or corrosion are found, reinstall ﬁ tting as follows.
3) Ensure entire ﬁ tting is alodined and primed prior to installation, otherwise ﬁ nish 
IAW SA226/227 SRM, Chapter 51-30-02, including the attachment holes.
4) Fay seal ﬁ tting to stabilizer spar IAW SA226/227 SRM, Chapter 51-30-03.
5) Secure ﬁ tting to stabilizer with AN4-7A bolts, AN960-416L washers and MS21042L4 
nuts (See Figure 1). Torque nuts 65-90 inch lbs (7.34-10.17 Nm).
6) Secure PTA rod end to upper attach ﬁ tting (Refer to SA226 IPC 27-40-02, Fig 1 
and Service Letter 226-SL-031 for part numbers, correct hardware orientation and 
stack-up). Torque nuts 100-140 inch lbs (11.30-15.82 Nm).
C. Return to Service:
1) Reconnect main batteries and reconnect Ground Power Unit to aircraft. Remove 
tags from switches and breakers.
2) Remove placard from cockpit pitch trim controls installed in Step 2.A.3).
3) Remove tags from breakers and switches pulled in step 2.A.2) and reset.
4) Perform Operational Test - Actuator Time Check IAW SA226 MM, Section 27-40-02.
5) Perform Operational Test - Indicating and Warning IAW SA226 MM, Section 27-
41-03 or 27-42-03 as appropriate for airplane S/N.
6) Install all access panels and components removed to perform this service bulletin.
D. Complete aircraft records in accordance with 14 CFR 43.9.
E. Complete and return service bulletin Compliance Form to M7 Aerospace Technical 
Publications Department. Email: MetroTech@M7Aerospace.com

### Page 9

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 5 of 8
SERVICE BULLETIN
SA226 SERIES
3. MATERIAL LISTING
ITEM PART NUMBER QTY
LH/RH Upper Attach Fitting Assy. §
(Airplane S/N AT001-074; TC201-419) 27-43062-013R * AR
As an alternative to 27-43062-013R Fitting Assembly, the following parts may be 
assembled:
Fitting § 27-43062-019R * 1
Bushing NAS77A-5-26 ** 1
Bushing NAS77A-5-38 ** 1
LH/RH Upper Attach Fitting Assy. §
(Airplane S/N T201-417) 27-43062-015R * AR
As an alternative to 27-43062-015R Fitting Assembly, the following parts may be 
assembled:
Fitting § 27-43062-011R * 1
Bushing NAS77A-5-26 ** 1
Bushing NAS77A-5-38 ** 1
Upper Attach Fitting Assembly to Stabilizer Hardware:
Bolt AN4-7A ** ҂ AR
Washer AN960-416L ** ҂ AR
Nut MS21042L4 ** ҂ AR
PTA Rod End to Upper Attach Fitting 
Hardware
Ref SA226 IPC 27-40-02, Fig 1 
or Service Letter 226-SL-031 AR
§ M7 Aerospace Sales Support item: M7-Sales@M7Aero.com. Fitting Assembly comes 
with NAS77A-5-26 and NAS77A-5-38 bushings installed.
 * An "R" following the part number indicates the attach bolts holes (4 off) are omitted, to 
be located on installation to match existing aircraft structure.
 ** Customer furnished material. 
҂ Alternate bolts NAS6204, NAS6304, NAS6704 (measure grip length as required) and 
alternate washers NAS1149F0432P and NAS1149G0432P are permitted. Permissible 
to adjust washer thickness to ensure correct torque and installation of bolt if alternate 
hardware or aircraft build requires adjustment.

### Page 10

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 6 of 8
SERVICE BULLETIN
SA226 SERIES
62708101
PITCH TRIM
ACTUATOR
AN4-7A
BOLT
AN960-416L
WASHER
MS21042L4
NUT
REFER TO 226 IPC 27-40-02, FIG 1 AND SERVICE LETTER 226-SL-031
FOR HARDWARE PART NUMBERS AND STACK-UP
UPPER ATTACH
FITTINGS
ROD
ENDS
FIGURE 1
LOCATOR - UPPER ATTACH FITTINGS

### Page 11

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 7 of 8
SERVICE BULLETIN
SA226 SERIES
FIGURE 2
UPPER ATTACH FITTING INSPECTION AREAS
62708102
RADIUS AREA, BOTH SIDES
(PROBABLE CRACK LOCATION)
FITTING TO STABILIZER ATTACH
BOLT HOLES, 4 PLACES
(PROBABLE CRACK LOCATION)
ACTUATOR LUG
PITCH TRIM ACTUATOR
UPPER ATTACH FITTING

### Page 12

Issued: April 13, 2016
Revised:  June 27, 2016
226-27-081 R1 
Page 8 of 8
SERVICE BULLETIN
SA226 SERIES
27-43062 FITTING
NAS 77A-5-38 BUSHING
NAS 77A-5-26 BUSHING
LUGS OF
FITTING
FWD
0.008 INCH
A
A
VIEW A - A
SHOWN AS SECTION THROUGH CENTER OF BOLT HOLES.
(PILOT SIDE SHOWN FOR CLARITY, CO-PILOT SIDE IS SAME).
AFTER INSTALLATION OF
THE BOLT, ASSURE A
MINIMUM GAP OF 0.008
INCH IS PRESENT BETWEEN
THE 27-43062 FITTING AND
THE FLANGE OF THE
NAS 77A-5-38 BUSHING,
AS SHOWN.
62708103
NAS 77A-5-38 BUSHING
NAS 77A-5-26 BUSHING
FIGURE 3
UPPER ATTACH FITTING BUSHING LOCATION/ORIENTATION

### Page 13

SERVICE BULLETIN COMPLIANCE FORM
226-27-081 R1
TO: OPERATOR OR SERVICE FACILITY ACCOMPLISHING BULLETIN
Please complete this compliance form, and  mail according to the instructions on the 
reverse side.
Thank you for returning this form.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Aircraft Model Aircraft Serial Number 
Bulletin Issue Date  Revision Date 
Aircraft Registration Number   
Operator/Owner   
Time on Aircraft   
Date Accomplished   
Comments

### Page 14

M7 AEROSPACE,  LLC
 10823 NE Entrance Road
 San Antonio, Texas 78216-6001
(Staple)
 ATTN: Technical Support Department
Fold  Here to Mail
Fold  Here to Mail
Place
Stamp
Here

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
