# M7 Aerospace Service Bulletin 26-56-001

Copy: No revision named ("U.S. DOT/FAA - Service Bulletin (3)"), 12 pages: PDF https://openairdocs.org/files/sha256/af/5d/af5d2f72c9d4dde6001576a7356f74b98a6131f24003a955e10aaa8fc96379ad; text https://openairdocs.org/service-documents/m7-aerospace/sb-26-56-001/file/af5d2f72c9d4.md. Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2011-0014; AD 2011-02-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Fairchild](https://openairdocs.org/service-documents/m7-aerospace.md) (issued as M7 Aerospace)
- Type: Service bulletin (Service Bulletin)
- Number: 26-56-001
- Page: https://openairdocs.org/service-documents/m7-aerospace/sb-26-56-001

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-02-04](https://openairdocs.org/ad/2011-02-04.md), effective Jan 24, 2011: No revision named

## Text (12 pages)

Rights: © M7 Aerospace. Filed by the FAA in regulations.gov docket FAA-2011-0014; AD 2011-02-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Issued: December 01, 2010 26-56-001
Page 1 of 12
SERVICE BULLETIN
SA26 SERIES
Windows
Inspection of Cockpit Heated Windshields (P/N 26-21126)
1. PLANNING INFORMATION
A. Effectivity:
All SA26 Series Aircraft
B. Reason:
Over a 2.5 year calendar period, the window manufacturer and repair facility has
repaired 19 windows with inner glass ply fracture. The manufacturer deems inner
glass ply failure as critical to the structural integrity of the window.
C. Description:
This service bulletin implements repetitive inspections on heated glass wind-
shields (P/N 26-21126) and if noted damage is found, replacing the affected
window.The inspections defined in this service bulletin are intended to identify
glass shear and / or interlayer cracking that may be present in the windshield
assembly. These inspections are focused on the areas adjacent to the windshield
metal insert with particular attention to areas not directly adjacent to the wind-
shield heating grid. (See Figures 2 and 3)
D. Compliance:
Mandatory
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
M7 Aerospace  estimates 2 manhours (1 manhour per window) to accomplish this
service bulletin. This estimate is for direct labor only accomplished by an experienced
crew. Adjust the estimate with operator task hour data if necessary.
G. Material-Cost and Availability:
(1) Cost:
Because of pricing fluctuations, individual cost estimates should be obtained from
your normal material procurement outlet.
(2) Availability:
Not applicable.

### Page 2

Issued: December  01, 2010 26-56-001
Page 2 of 12
SERVICE BULLETIN
SA26 SERIES
H. Tooling-Price and Availability:
Not applicable
I . Weight and Balance:
Not affected
J. Reference:
None
NOTE: References are for manufacturers’ use only.
K. Other Publications Affected:
SA26 Series Maintenance Manual.
2. ACCOMPLISHMENT INSTRUCTIONS
A. Perform inspections in 2.B. in accordance with intervals called out in Table 001.
B. Inspection:
(1) Determine Time in Service of the LH and RH cockpit heated windshields.
(2) With the use of maintenance stands or ladders, obtain adequate access to
perform a detailed visual inspection of the entire periphery of the LH and RH
cockpit heated windshields from the outside of the aircraft.
(3) Clean the inner and outer surfaces of the LH and RH cockpit heated windshields
per step 4.J. Ensure that the surface of the glass is free from dirt, oil, or other
contaminants.
(4) With the use of a flashlight and 10X magnification, perform a detailed visual
examination of the inner glass ply, the interlayer, and the outer glass ply in an area
defined by the inner edge of the metal insert (see Figure 3) and extending inward
3.0 inches toward the center of the windshield. Inspect for indications of delami-
nation, interlayer cracking, moisture ingress, and / or glass shear. The viewing
angle for the inspection should extend from a line of sight that is perpendicular to
the surface of the glass to an angle extending approximately 45 degrees to either
side of this plane as shown in Figure 5.
(5) For indications of delamination, adhere to the limits and take appropriate action
as defined in step 3.
(6) For indications of glass shear or interlayer cracking, the windshield must be
repaired / replaced by an FAA approved vendor prior to further flight.

### Page 3

Issued: December 01, 2010 26-56-001
Page 3 of 12
SERVICE BULLETIN
SA26 SERIES
(7) For removal and installation instructions for heated windshields refer to step 4.
C. Complete aircraft records according to 14 CFR 43.9.
D. Complete and mail Service Bulletin compliance form.
3. DEFINITIONS AND ACCEPTANCE CRITERIA - WINDSHIELDS
A. Definitions
Critical The viewing area of the windshield used for taxiing, takeoff, climb,
cruise, and landing.
Semi-Critical The viewing area of the windshield used for general flight vision.
Delamination Delamination - The disbonding of either the inner and / or the outer
glass component from the adjacent interlayer material. It appears as
a clear bubble that is flat and smooth with a circular or irregular shape.
Glass Shear A fracturing of portions of the glass material adjacent to the interlayer
material. It can extend to significant areas of failure parallel to the
glass surface. Glass shear can be similar in appearance to delami-
nation, but can be differentiated from delamination by "rainbow"
         B 1100 to 5000      3 weeks from publish    Every 100 hours *TIS until
     date of SB.   window reaches category C.
         C Greater than 5000      3 weeks from publish    Every 50 hours *TIS.
     date of SB.
   Category Hours *TIS on each       Threshold Inspection    Repetitive Inspection date/
new or repaired      date/time (on or before)    time (on or before)
windshield
         A Less than 1100       3 weeks from publish    Every 150 hours *TIS until
      date of SB.   window reaches category B.
THRESHOLD/REPETITIVE INSPECTION INTERVALS
FOR 26-21126 HEATED WINDSHIELDS
TABLE 001
    * TIME IN SERVICE

### Page 4

Issued: December  01, 2010 26-56-001
Page 4 of 12
SERVICE BULLETIN
SA26 SERIES
colors, distinct shear planes and crushed contours displayed as a
white "frosting" in appearance. Inspection for glass shear can be
aided by the use of and LED type flashlight, particularly in highlighting
the "rainbow" colors associated with glass shear.
Interlayer CrackingA narrow break, fissure, or separation in the interlayer material.
Interlayer cracking normally occurs adjacent to the glass components
along the inboard edge of the metal insert and also at the interlayer
release boundary. When viewed from the edge of the crack (see
Figure 4), interlayer cracking is indicated as a prominent black line
type crack / tear through the thickness of the interlayer. When viewed
looking at the plane of the crack (see Figure 4), striations in the
interlayer can be observed.
B. Critical Area Inspection – Glass Windshields
NOTE: The critical area is the area of the laminated glass windshields used for
taxiing, takeoff, climb, cruise, and landing measured 2.0 in (50.8 mm) from
inner edge of retainer, around entire periphery towards center of windshield,
except measured 0.5 in (12.7 mm) around the temperature sensors.
(1) Delamination
(a) Cloudy or milky appearance in the delamination indicates moisture or
solvent penetration. Windshields with this condition should be replaced at
the earliest opportunity.
(b) Delaminated areas characterized by irregular or jagged boundaries indi-
cate uneven separation of the vinyl and glass.
(c) Replace windshield if one of the following conditions are noted:
1 Area of vision required for safe operation is affected (pilot's discre-
tion).
2 Windshield heat system inoperative.
(2) Glass Shear
(a) Glass Shear  in any portion of the windshield requires replacement prior to
further flight.
(3) Interlayer Cracking
(a) Interlayer Cracking  in any portion of the windshield requires replacement
prior to further flight.
C. Semi-Critical Area Inspection – Glass Windshield
NOTE: Semi-Critical areas are the perimeter of the glass windshield, within the 2.0 in
(50.8 mm) region from the inner edge of the retainer.
(1) Delamination
(a) Cloudy or milky appearance in the delamination indicates moisture or
solvent penetration.
(b) Delamination areas characterized by irregular or jagged boundaries indi-
cate uneven separation of the vinyl and glass.

### Page 5

Issued: December 01, 2010 26-56-001
Page 5 of 12
SERVICE BULLETIN
SA26 SERIES
(c) Replace windshield if one of the following conditions is noted:
1 Area of vision required for safe operation is affected (pilot's discre-
tion).
2 Windshield heat system inoperative.
(2) Glass Shear
(a) Glass Shear  in any portion of the windshield requires replacement prior to
further flight.
(3) Interlayer Cracking
(a) Interlayer Cracking  in any portion of the windshield requires replacement
prior to further flight.
4. REMOVAL/INSTALLATION – HEATED WINDSHIELD
A. Removal – Heated Windshield
(1) Remove instrument panel glareshield.
(2) Remove interior panels and covers.
(3) Remove windshield mounting screws.
(4) Remove panel and cover clips.
NOTE: Mark location of clips for reference during windshield installation.
(5) Remove inner fasteners.
(6) Remove wiring from windshield.
(7) Remove windshield by pushing panel outward.
(8) If windshield sealant does not release after pushing panel outward, proceed as
follows:
(a) Cut through sealant around outer edges of windshield with sharp-bladed
instrument.
(b) Spray Ram Chemicals Aerosol Mold Release 225 (or equivalent) into
crevices made from cutting around outer edges of windshield.
WARNING: WEAR EYE PROTECTION AND GLOVES, WHEN USING SAFETY
WIRE TO CUT WINDSHIELD SEALANT.
(9) If windshield sealant will not release after cutting and spray application of mold
release agent, proceed as follows:
(a) Dig a small hole in sealer and push through a length of 0.020 inch (0.51 mm)
thick stainless steel safety wire.
(b) Wrap ends of wire around a screwdriver or similar tool.

### Page 6

Issued: December  01, 2010 26-56-001
Page 6 of 12
SERVICE BULLETIN
SA26 SERIES
(c) With one person inside and another outside, pull wire in a reciprocating
motion through sealer until windshield is free. Remove windshield.
(10) Clean all sealant residue from windshield frame with methyl propyl ketone (MPK).
B. Installation – Heated Windshield
NOTE: The following procedures apply to all heated window installations, using either
reusable existing heated windshields or new heated windshield panel with
required drilling, trimming, counterboring, countersinking, and deburring com-
pleted IAW paragraphs 4., E. through H., this section.
(1) Inspect heated windshield panel for distortion and defects; mask windshield
for protection.
(2) Check flatness of windshield supporting structure, and maintain a maximum
of 0.030 inch (0.762 mm) gap between windshield and faying surface of
airframe structure. Maximum gap may be maintained by bonding shims to
frame with EC1838 structural adhesive.
(3) Apply thin coat of MIL-S-8802 sealant (or approved equivalent sealant) to aircraft
windshield frame.
NOTE: MIL-S-8802 sealant may also be used as an underlay material to fill a
minor mismatch of heated windshield with surrounding aircraft windshield
frame.
MIL-S-81733 sealants are approved equivalents for MIL-S-8802 sealant.
Ram Chemicals Aerosal Mold Release #225 may be used as a release
agent between windshield(s) and sealing compound to facilitate removal
of window(s).
(4) Apply approximately 0.188 inch (4.775 mm) thickness of MIL-S-8802 sealant (or
equivalent) to each corner of windshield frame.
(5) Position windshield into aircraft mounting structure. Ensure a minimum gap of
0.030 in (0.762 mm) between windshield glass and aircraft mounting structure.
(6) Apply a small amount of MIL-S-8802 sealant (or equivalent) around each screw
prior to installing into screw holes.
(7) Install screws just snug, and allow sealant to set.
(8) Stage-torque screws 15 to 20 inch-pounds (1.69 to 2.26 N·m), using a cross
sequence tightening schedule (e.g., 12 o'clock to 6 o'clock, 3 o'clock to 9 o'clock,
5 o'clock to 11 o'clock, etc.).
NOTE: Do not exceed the suggested minimum torque values during initial tight-
ening.
(9) Install interior panel and cover clips.
(10) Install all inner retainers.
(11) Tighten inner retainer screws hand tight, then loosen one-quarter (1/4) turn, using
a cross sequence tightening schedule.
(12) Install wiring to electro-thermal windshield.

### Page 7

Issued: December 01, 2010 26-56-001
Page 7 of 12
SERVICE BULLETIN
SA26 SERIES
(13) Install heated windshield panels and covers.
(14) Fill spaces between windshield and aircraft primary structure with sealant.
(15) After sealant has cured, remove all masking tape and clean windshield. Install
glareshield.
C. Required Equipment
(1) Hand drill, high-speed, 15,000-25,000 RPM.
(2) Drill press, automatic constant feed.
(3) High-speed steel drill bit, 0.1935 inch.
(4) Counterbore bit, 0.313 inch with 0.031 inch radius and 0.1935 inch pilot.
(5) Countersink bit, 0.1935 inch.
(6) Torque wrench.
(7) Steel rule.
(8) Rasp.
(9) Sheet metal Cleco fasteners or draw mono-locks.
(10) China marker.
(11) Spacers, aluminum.
(12) Sealant, MIL-S-8802, or the following approved equivalent:
(a) Sealant, MIL-S-81733.
D. Preparation
(1) Inspect new windshield for general condition. Mask for protection.
E. Drilling and Trimming – Heated Windshield
(1) Position new windshield in place in the aircraft primary structure.
(2) Determine amount of trimming required for proper fit.
NOTE: Approximately 0.063 inch (1.600 mm) space should be allowed for
sealing between the outer edges of the new windshield frame and the
aircraft primary structure.
(3) Trim new windshield frame as required with rasp. Do not contact windshield glass
with rasp.
(4) With new windshield held firmly in place, and using the aircraft primary structure
retainer as reference, drill three (3) 0.190 - 0.194 in (4.826 - 4.928 mm) holes, one
(1) hole at top and one (1) at each side of windshield frame.
NOTE: Drill holes from cockpit side of frame.
(5) Remove windshield and place it on a flat work area with inner side down. Place
old windshield, inner side down, on top of new windshield.

### Page 8

Issued: December  01, 2010 26-56-001
Page 8 of 12
SERVICE BULLETIN
SA26 SERIES
(6) Align old windshield with new windshield, securing windshields together with bolts
and nuts through holes in new windshield frame.
(7) Use old windshield as a template guide, and drill remaining holes through new
windshield frame.
NOTE: Drill holes on a drill press to help ensure proper alignment.
F. Counterboring – Heated Windshield
(1) Place new windshield on drill press with inner side facing up. Adjust drill press to
counterbore a maximum depth of 0.192 - 0.196 in (4.877 - 4.978 mm) into frame.
(2) Counterbore all holes with 0.313 inch counterbore bit with 0.031 inch radius and
a 0.1935 inch pilot.
G. Countersinking – Heated Windshield (Figure 1)
(1) Place new windshield on drill press with outer side facing up.
(2) Countersink all holes using a 0.1935 inch countersink.
NOTE: Countersink must have an included angle of 100° and produce the
degree of flushness required with retaining screws installed.
Countersinking Heated Windshield
Figure 1
H. Deburring
(1) Remove chips and burrs on both sides of the windshield frame.
I. Installing Spacers
(1) Ensure spacers are installed flush.
J. Cleaning
(1) Remove masking tape.
(2) Remove dirt and other substances from glass surface with clean water.
  0.188 INCH
  (4.775 MM)
0.371 - 0.383 INCH
(9.423 - 9.728 MM)
NAS43DD3-12 SPACER
6M561000201
OUTER FRAME (ALUMINUM)
VINYL INTERLAYER
INTER FRAME (ALUMINUM )
PLASTIC GASKET

### Page 9

Issued: December 01, 2010 26-56-001
Page 9 of 12
SERVICE BULLETIN
SA26 SERIES
(3) Wash with mild soap and water or a 50/50 solution of isopropyl alcohol and water.
Do not use any abrasive materials or any strong acids or alkalines. When wiping
the surface, use a soft cloth or sponge and use a straight rubbing motion.
(4) Rinse thoroughly and dry; do not apply wax.

### Page 10

Issued: December  01, 2010 26-56-001
Page 10 of 12
SERVICE BULLETIN
SA26 SERIES
Heating Grid
Outer Edge of 
Windshield & 
Metal Insert
Metal Insert
Inner Edge
View Looking Forward
at RHS Windshield
COCKPIT HEATED WINDSHIELD
FIGURE 2
COCKPIT HEATED WINDSHIELD COMPONENTS
FIGURE 3
 
Outer glass
Inner glass
Interlayer
Metal
Retainer
Metal
Insert
Inner Edge of 
Metal Insert
Sealant
3.0 inch

### Page 11

Issued: December 01, 2010 26-56-001
Page 11 of 12
SERVICE BULLETIN
SA26 SERIES
INTERLAYER CRACKING
FIGURE 4
 
Outer glass
Inner glass
Interlayer
Metal
Retainer
Metal
Insert
When viewed from edge, crack appears 
as a black line or a series of short 
disconnected black lines
Interlayer crack
 
Outer glass
Inner glass
Interlayer
Metal
Retainer
Metal
Insert
When viewed from side,
 striations are visibleInterlayer crack

### Page 12

Issued: December  01, 2010 26-56-001
Page 12 of 12
SERVICE BULLETIN
SA26 SERIES
 
Outer glass
Inner glass
Interlayer
Metal
Retainer
Metal
Insert
Plane perpendicular to 
plane of glass
45º45º
Extent of viewing 
angle for inspection
INSPECTION VIEWING ANGLES
FIGURE 5

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
