# Maule Service Bulletin 11: No revision named

- Rights: © Maule. Filed by the FAA in regulations.gov docket FAA-2013-0725; AD 98-15-18 R1 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Maule Service Bulletin 11](https://openairdocs.org/service-documents/maule/sb-11.md)
- Title as filed: U.S. DOT/FAA - Maule Service Bulletin No. 11
- Pages: 5
- PDF: https://openairdocs.org/files/sha256/58/a6/58a6d25d18a4d198578f643878bb18f73075461723af16ff71bc018ebef49bd5
- Page: https://openairdocs.org/service-documents/maule/sb-11/file/58a6d25d18a4

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

2099 GA Hwy. 133 South  MAULE AIR, INC.  Phone: 912-985-2045
Moultrie, GA 31768  FAX: 912-890-2402
FAA APPROVED  SERVICE BULLETIN NO. 11  Page 1 of 5
DATE:  Date: 10/30/95
SUBJECT: Wing Lift Strut Assembly Inspection/Replacement.
STATUS: Mandatory.
AUTHORITY: The technical contents of this Service Bulletin have been approved
by the FAA.
PART I
AIRCRAFT AFFECTED: A11 Maule Models
COMPLIANCE: Before next flight and each twenty-four (24) month period thereafter.
If the aircraft is new with the original lift struts installed, the repetitive
inspection begins when the aircraft is twenty-four (24) months old. Or, if the
wing lift struts are new and were installed within the last twenty-four (24)
months, inspection is required no later than twenty-four (24) months after new
lift strut installation.
PURPOSE:  The intended objective of this inspection program for the wing strut
assemblies is to detect internal lift strut tube corrosion, most likely to
occur on the bottom surface at the lower end (near the fuselage attachment).
Since lift struts are closed tubular structures, internal corrosion in most
cases may not be readily apparent until corrosion has advanced completely
through the tube wall. This corrosion if allowed to progress, may lead to
failure of the wing lift strut, and the possibility of loss of wing structure
This service bulletin provides an inspection procedure to detect
evidence of wing lift strut tube internal corrosion.
INSTRUCTIONS:
Remove wing lift struts and accomplish the inspection per inspection
procedures on Sketch "A": Caution: Take extra care in inspection for external
corrosion in the areas covered by the cuffs.
Remove lower and upper wing strut fairings (6 each).
Remove nuts from wing strut bolts (8 each).
of the inspection procedure and treatment reinstall rear lift struts on
aircraft.
IT'S PERFORMANCE THAT COUNTS

### Page 2 (OCR)

DATE:  NOV - 2 1995  MAULE AEROSPACE TECHNOLOGY, INC.  SERVICE BULLETIN NO. 11  Page 2 of 5  Date: 10/30/95
NOTE: For minimal effect on rigging, do not remove or adjust forks. If forks
are changed, install the new forks as close as possible to the same extension
as the old forks.  Do not interchange left and right struts.
d. Remove front struts, right and left and accomplish inspection and treat
(corrosion impediment) per instructions below. Upon successful completion
of the inspection procedure and treatment reinstall front lift struts on
Inspect forks for condition and replace as necessary. All attaching hardware
should be replaced.
After completion of the inspection procedure, but prior to the corrosion
impediment procedure of the wing lift struts, turn each wing lift strut upside
down and tap gently. This procedure is necessary to remove any water, debris,
or corrosion particles which may have accumulated.
Lift strut tubes indicating presence of internal corrosion and which fail
the inspection procedure must be replaced with new wing lift struts called
for in PART II of this Service Bulletin. Note: Should corrosion be apparent
from the outside, (rust pin holes or large rust stains) strut must be replaced
even if strut passes the inspection procedure. Note: If it is recorded in
aircraft logbook or you have knowledge of a strut being installed from one
side to the other side, strut must be replaced as top and bottom walls at
lower end may both be weakened by corrosion.
5.  Treat (corrosion impediment) each wing lift strut per the instruction
procedure Note on Sketch "A". Treatment must coincide with each inspection
as outlined in the compliance time above.
6.  Upon successful completion of the inspection procedure and treatment,
reinstall lift struts on aircraft.
7. Check aircraft rigging and adjust as necessary, use rigging procedures in
Maintenance Manual.
8. Make an appropriate logbook entry of compliance with this Service Bulletin.
PART II
MODELS AFFECTED: All Maule Models
COMPLIANCE: To coincide with the next regularly scheduled inspection event or
at next replacement of the wing lift strut, but not to exceed twenty-four
(24) months from the initial inspection as called for in PART I of this
Service Bulletin.
PURPOSE: PART II of this Service Bulletin announces the availability of new sealed
wing lift struts which, when installed, will relieve inspection requirements
of PART I of this Service Bulletin.
INSTRUCTIONS:
1. Remove old rear wing lift struts.
Prepare, prime and paint new sealed wing lift struts to match aircraft before
installation.
Inspect attach fittings and fairings for condition and replace as necessary.
All attaching hardware should be replaced.
4.  Install new Sealed rear wing lift strut assemblies, Maule Part Number 2200E
on each wing.
5.  Remove old front wing lift struts.
Install new Sealed front wing lift strut assemblies, Maule Part Number 2201E
on each wing.

### Page 3 (OCR)

MAULE AEROSPACE TECHNOLOGY, INC.  Page 3 of 5
DATE:  NOV - 2 1995  SERVICE BULLETIN NO. 11  Date: 10/30/95
NOTE: For minimal effect on rigging, adjust new struts to same length as old
struts prior to installation.
7. Check aircraft rigging  and adjust as necessary. Use Maule Maintenance Manual
as required to accomplish the proper rigging.
8. Upon successful completion of PART II of this Service Bulletin, make an
appropriate logbook entry of compliance and return the completed Compliance
Record Sheet, page 5 to Maule Air. Inc.
MATERIAL REQUIRED: As required by inspection for PART I or as required by PART
II, two (2) each Front Wing Strut Assemblies, Maule Part Number 2201E, two
(2) each Rear Wing Strut Assemblies, Maule Part Number 2200E, and four (4)
each 2001B Strut Fork.
AVAILABILITY OF PARTS: The following parts are available and may be purchased
From Parts Department of Maule Air, Inc.:
Quan.  Part No.  Item  Price each
2200E  Wing Strut - Rear  (Sealed)  $235.00**
220TE  Wing Strut - Front (Sealed)  $235.00**
4  2001B  Fork - Lower Strut  $65.00
4  AN315/316-8  Check Nut
4  AN320-6  Nut
4  AN380-3-3  Cotter Pin
4  AN960-516  Washer  $30.00
4  AN365-524  Nut
4  AN5-23A  Bolt
4  NAS464P-6-10  Bolt
qt.  *Randolph #315  Clear Tube Oil  $10.00
*Maule stocks.  Tubeseal (Lineoil), Valoil, Lionoil Multi-purpose L-1,
Paralketone, LPS-3, any other corrosion preventative liquid meeting Federal
Specification TT-S-176D, Mil-L-21260, Mil-C-6708, Type I or Mil-C-81309E,
Type II may be used.
**New low price in effect for next four (4) months beginning 12/4/95.

### Page 4 (OCR)

DATE: NOV - 2 1995  MAULE AEROSPACE TECHNOLOGT,  INC.  Page 4 of 5
SERVICE BULLETIN NO. 11  Date: 10/30/95
SKETCH "A"
VIEW OF MAULE FABRIC TESTER
BOTTOM VIEW OF FRONT LIFT STRUT
BOTTOM VIEW OF REAR LIFT STRUT
INSPECTION PROCEDURE
1. Securely tape a sheet of thin 1/4 inch grid  graph paper to the lower 12 inches
2. Usinge too led babroc festeres on all wing lift struts.  and holding tool normal to strut contour, apply
3. Remove the paper and inspect the lift strut tubes. A perceptible dent will
the dents are in the metal by carefully removing the paint.
Lift strut tubes indicating the presence of any perceptible dent in the
metal must be replaced with new lift strut assembly before further flight.
b. If no dents appear in the metal, the lift struts may be considered
airworthy.
NOTE
Before reinstalling strut, treat (corrosion impediment) each strut per the
following procedure:  (See page 3 for additional preservatives)
Inject one quart of Valoil or Lionoil Multi-purpose L-1, Linseed Oil,
Paralketone or any alternate preservative conforming to Federal
Specification TT-S-176D, into the bolt hole at the top of the strut.
b. Plug the bolt holes and slosh oil until interior of strut is thoroughly
coated.
c. Drain oil from strut (through bolt holes).
da  Reinstall strut to aircraft and check rigging.
4.  Record lift strut inspection and corrosion treatment in Aircraft Logbook and
return the completed Compliance Record Sheet, page 5 to Maule Air, Inc.
*Many Repair Stations have a Maule Fabric Tester or it may be purchased from Maule.

### Page 5 (OCR)

2099 GA Hwy. 133 South  MAULE AIR, INC.  Phone: 912-985-2045
Moultrie, GA 31768  FAX: 912-890-2402
SERVICE BULLETIN NO. 11  Page 5 of 5
Date: 10/30/95
INITIAL COMPLIANCE RECORD
Aircraft Model
Aircraft Serial No.
Aircraft Registration No.
Action taken (check one):
( ) Struts were removed, inspected in accordance with PART I (and found
airworthy) and procedure for oil-coating inside of struts per Note
in Sketch "A" has been accomplished.
Accomplished Inspection procedure for lift struts as outlined in
PART I of this SB and found that one or more had to be replaced.
Strut(s) was/were replaced as follows:  Please check.
( ) Left Front () Left Rear ( ) Right Front ( ) Right Rear
PART II complied with - please check:
() Left Front ( ) Left Rear ( ) Right Front ( ) Right Rear
Note: If you no longer own this aircraft, please forward this information
to the present owner/operator and notity the ractory of address/
ownership corrections.  Include aircraft model, serial number,
current owner's name and address. Corrections should be directed
to factory address below.
Owner's Name
Owner's Address
City  State  Zip
Certified by
Signature
Title
Owner, A & P, IA, etc.
Date performed
Please mail this Compliance Record to: Maule Air, Inc./Engineering Records
/2099 Georgia Highway 133 South/Moultrie, GA 31768 USA
IT'S PERFORMANCE THAT COUNTS

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
