# Mitsubishi Service Bulletin 107-57-005

Copy: No revision named ("SB107_57-005 Wing Spacer Plate – Insp. & Replac"), 16 pages: PDF https://openairdocs.org/files/sha256/4f/8f/4f8fcd96a2567beaa2794f6fd287a2c2bca0e41687b2675b05bc73878ffa469e; text https://openairdocs.org/service-documents/mitsubishi/sb-107-57-005/file/4f8fcd96a256.md. Rights: © Mitsubishi. Filed by the FAA in regulations.gov docket FAA-2016-9139, the docket of a proposed AD (Federal Register 2016-22182, 2019-03397). Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Mitsubishi](https://openairdocs.org/service-documents/mitsubishi.md)
- Type: Service bulletin (Service Bulletin)
- Number: 107-57-005
- Page: https://openairdocs.org/service-documents/mitsubishi/sb-107-57-005

## Text (16 pages)

Rights: © Mitsubishi. Filed by the FAA in regulations.gov docket FAA-2016-9139, the docket of a proposed AD (Federal Register 2016-22182, 2019-03397). Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

M U - 2 
S E R V I C E  B U L L E T I N 
MITSUBISHI HEAVY INDUSTRIES, LTD. 
NAGOYA AEROSPACE SYSTEMS WORKS  
10, OYE-CHO, MINATO-KU, NAGOYA, JAPAN 
 
 
Page 1 of 14 
No. 107/57-005 DATE: May 3, 2016 
Subject: Wing Spacer Plate – Inspection and Replacement of 
Effectivity: MU-2B-25/-26/-26A/-40: S/N 313SA, 321SA, 348SA through 
459SA 
MU-2B-36A/-60: S/N 661SA, 697SA through 1569SA 
Purpose: To ensure the continued airworthiness of the wing structures , 
conduct a one-time fluorescent penetrant inspection for the 
wing spacer plates and replace them, if necessary. 
Background: As part of aging aircraft pr ogram, one -piece and three -piece 
main wings were subject of detailed teardown inspections, and 
cracks were found in the wing spacer plate s attached to the 
forward lower spar at W.STA580. The cracks resulted from 
fatigue to be caused by flight load.  
Compliance: Mandatory 
Approval: Engineering aspects of this Service Bulletin are FAA Approved 
Time of Compliance: a) For aircraft with flight time 7,500 hours or over 
- within 200 hours, or 12 months whichever comes first after 
receipt of this Service Bulletin. 
b) For aircraft with flight time less than 7,500 hours 
- to be include in 7,500 hours inspection. 
Responsible Agency of 
Compliance: 
MU-2 Owners/Operators 
Disposition of Removed 
Parts: 
Scrap 
Spare Parts Affected: Replacement Kit (P/N 035A-900021-101/-102)  
Required Man Hours: Inspection ~approximately 4 man hours for each side 
Replacement ~approximately 40 man hour s for each side  
excluding preparation and restoration 
Special Tools Required: None 
Weight and Balance 
Change: 
Negligible 
Flight Manual Revision: None

### Page 2

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 2 of 14 
INSTRUCTIONS 
Refer to applicable Maintenance Manual, Illustrated Parts Catalog and 
Structural Repair Manual to comply with this Service Bulletin. 
 
 
1. INSPECTION PROCEDURE 
 
NOTE 
Identify and store all removed parts and attaching hardware. 
If it is necessary to remove further parts for access, inspection and 
replacement, you can remove those parts beyond following process. If you 
can access, inspect and replace without removing the parts instructed in 
following process, it is not necessary to remove the parts. 
 
1.1 PREPARATION 
(1) Electrically ground the aircraft. 
(2) Remove the wing center lower fillet and the inner wing leading edge in accordance 
with applicable Maintenance Manual. 
(3) Remove sealant and primer from the inspection area between the spacer plate and 
the skin with a nonmetallic scraper. See Figure 1 and 2. 
(4) Clean and expose the inspection surface. 
 
1.2 INSPECTION 
(1) Conduct a fluorescent penetrant inspection to the inspection area shown in Figure 1 
and 2 on both left and right sides of wing in accordance with applicable Maintenance 
Manual. 
 
NOTE 
Personnel performing fluorescent penetrant inspection must be qualified 
and certified as a Level II or higher based on the requirements of National 
Aerospace Standard NAS410 or equivalent standard. 
 
(a) When a crack of 0.6 inches or greater is found 
Replace the discrepant spacer plate with a new improved spacer plate (P/N 
017A-11102-13/-14) and scrap the discrepant spacer plate. Replacement 
procedure is instructed in Section 2. 
(b) When a crack of less than 0.6 inches is found 
It is allowed to monitor the crack growth by repetitive inspection at the interval of 
600 hours. However, the spacer plate must be replaced when the crack length 
grows beyond 0.6 inches. 
 
1.3 RESTORATION 
(1) Clean up the inspection area and apply Alodine and zinc chromate primer. 
(2) Apply sealant to fill the gaps between the spacer plates and the skin in accordance 
with applicable Maintenance Manual. 
(3) Restore the inner leading edge. 
(4) Restore the wing center lower fillet.

### Page 3

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 3 of 14 
2. REPLACEMENT PROCEDURE 
 
NOTE 
Replacement Kit may be purchased from Mitsubishi Heavy Industries 
America, Inc. (MHIA) through Mitsubishi MU-2 Authorized Service Center 
Network. 
Replacement of the spacer plate should be conducted in accordance with 
the installation drawing contained in Replacement Kit. 
 
2.1 PREPARATION 
 
NOTE 
Removal of the engines, each system, the wing and the other attaching 
hardware should be accomplished in accordance with applicable 
Maintenance Manual. 
 
(1) Electrically ground the aircraft. 
(2) Drain fuel and purge fuel tanks. 
(3) Remove all wing-fuselage fillets, the fuel system, the engines, the air conditioning 
and wing de-icer system, the electrical and instrument system, and the flight control 
system from the wing. 
(4) Remove the wing and set appropriate support. 
(5) Remove the inner wing leading edge. 
(6) Remove the shut off valves. 
(7) Remove the fuel tank access doors. 
 
2.2 REPLACEMENT 
(1) Remove sealant inside the integral tank with a nonmetallic scraper. 
(2) Remove the outer wing-fuselage fitting and the inner support fitting. If shims are 
installed, record thickness and location, and store. 
(3) Drill out and cut off the fasteners on and around the spacer plate. 
 
NOTE 
Several tack rivets and a nut plate are hidden under the skin and sealant 
as shown in Figure 4. Be careful not to damage adjacent structural 
components when removing the spacer plate. 
 
(4) Peel up the skin and slide out the spacer plate from the wing.  
(5) Remove remaining sealant inside of the integral tank. Clean up the integral tank and 
the outer wing-fuselage fitting and the inner support fitting. 
(6) Duplicate all fastener holes to a new spacer plate from the removed spacer plate. Do 
not apply countersink to the holes for tack rivets and nut plate installing rivets. 
(7) Temporary locate the new spacer plate and drill out the holes for tack rivets to the 
skin by picking up the existing tack rivet holes on spar through the new spacer plate.  
(8) Drill out the holes for nut plate installing rivets to the skin by picking up the existing 
holes on spar through the new spacer plate.  
(9) Remove the new spacer plate and clean up.

### Page 4

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 4 of 14 
(10) Apply sealant to the new spacer plate and the existing structure where sealant 
should be applied before fastening in accordance with the installation drawing (refer 
to Figure 5), and locate the spacer plate. 
(11) Install all fasteners to the spacer plate, a nut plate and tack rivets in accordance with 
the installation drawing (refer to Figure 3 and 4). 
(12) Adjust the gap between the outer wing-fuselage fitting and the spacer plate with 
laminated shim within 0.005 inches (refer to Figure 3). 
(13) Touch up the laminated shim with zinc chromate primer. 
(14) Install the outer wing-fuselage fittings and the inner support fitting. 
(15) Clean up inside and outside of the integral tank. 
(16) Apply integral tank sealant and dry in accordance with applicable Maintenance 
Manual and the installation drawing (refer to Figure 5). 
(17) Apply sealant to fill the gaps between the spacer plate and the skin shown by the 
hatched area in Figure 2 in accordance with applicable Maintenance Manual. 
 
2.3 FUEL LEAKAGE CHECK 
(1) Conduct the integral tank leakage test in accordance with applicable Maintenance 
Manual. 
(2) If fuel leakage is found, rework sealing. 
 
2.4 RESTORATION 
 
NOTE 
Restoration of the disrupted systems, including rigging and operational 
tests, should be accomplished in accordance with applicable Maintenance 
Manual. 
 
(1) Install the fuel tank access doors. 
(2) Install the fuel shut off valves. 
(3) Install the inner wing leading edge. 
(4) Install the wing. 
(5) Install the flight control system, the electrical and instrument system, the air 
conditioning and wing de-icer system, the engines, the fuel system and all 
wing-fuselage fillets. 
(6) Refuel full and check no leakage. 
 
 
3. RECURRING INSPECTION 
(1) If no crack is found during the inspection, repeat the inspection in accordance with the 
revised Maintenance Requirement Manual at the interval of 2,000 hours. 
(2) If the crack of less than 0.6 inches is found, repeat the inspection at the interval of 600 
hours for crack growth monitoring in accordance with this Service Bulletine. When the 
crack length exceeds 0.6 inches, replace the cracked spacer plate with a new improved 
spacer plate. 
(3) Once the spacer plate is replaced with a new improved spacer plate (P/N 
017A-11102-13/-14), recurring (repetitive) inspection is not required.

### Page 5

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 5 of 14 
4. LOGBOOK ENTRY 
Upon completion of this Service Bulletin, make an appropriate maintenance entry in the 
logbook similar to “Service Bulletin No. 107/57-005 complied with on (date) by (name), 
number/stamp.” 
 
5. COMPLETION 
Complete the enclosed compliance card and mail back to Mitsubishi Heavy Industries 
America, Inc. in care of Turbine Aircraft Services, Inc.   
 
Turbine Aircraft Services, Inc. 
4550 Jimmy Doolittle Drive 
Addison, Texas 75001 
 
Attention: Manager, Publications 
Phone: (972) 248-3108 X 209 
Fax: (972) 248-3321

### Page 6

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 6 of 14 
Parts and Material Required 
The following parts and material are required to comply with this Service 
Bulletin. 
Replacement Kit may be purchased from Mitsubishi Heavy Industries 
America, Inc. (MHIA) through Mitsubishi MU-2 Authorized Service Center 
Network. 
All the parts and material except for Replacement Kit may be procured 
locally. 
 
PART NUMBER DESCRIPTION 
QTY/SHIP 
REMARKS LH 
(-101) 
RH 
(-102) 
KIT number 035A-900021-101 to replace LH spacer plate 
KIT number 035A-900021-102 to replace RH spacer plate 
035A-11076 DRAWING 1 1   
017A-11102-13 SPACER PLATE 1     
017A-11102-14 SPACER PLATE   1   
017A-11102-15 LAMINATED SHIM 1 1   
800-0115-10 LOCK-O-SEAL 14 14 change PN of 800-015-10 
NAS1149D0363H WASHER 14 14   
NAS1149D0316H WASHER 4 4   
MS20002C7 WASHER 2 2   
MS20002-7 WASHER 2 2   
NAS679A3W NUT 16 16   
H20-7 NUT 2 2   
NAS1473A3 DOME NUT 1 1   
MS20426AD3-10 RIVET 4 4 not contained in the KIT 
MS20426AD4-5 RIVET 6 6 not contained in the KIT 
MS20426AD5-12 RIVET 9 9 not contained in the KIT 
MS20426AD5-7 RIVET 3 3 not contained in the KIT 
MS20470AD3-10 RIVET 2 2 not contained in the KIT 
MS20470AD3-11 RIVET 2 2 not contained in the KIT 
MS20470AD3-7 RIVET 1 1 not contained in the KIT 
MS20470AD4-5 RIVET 15 15 not contained in the KIT 
MS20470AD5-12 RIVET 11 11 not contained in the KIT 
MS20470AD5-13 RIVET 6 6 not contained in the KIT 
MS20470AD5-7 RIVET 9 9 not contained in the KIT 
MS20470AD5-9 RIVET 6 6 not contained in the KIT 
NAS1097AD4-9 RIVET 16 16 not contained in the KIT 
AMS-S-8802 Class A 
 or equivalent 
SEALANT AR AR not contained in the KIT 
AMS-S-8802 Class B 
 or equivalent 
SEALANT AR AR not contained in the KIT 
TT-P-1757 or equivalent PRIMER AR AR not contained in the KIT

### Page 7

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 7 of 14 
 
Figure 1: LOCATION OF SPACER PLATE INSPECTION 
(Typical, LH side shown, RH side opposite.) 
OUT B/D 
(LH) 
FWD 
LKG UP 
Spacer plate 
OUT B/D 
(LH) 
FWD 
LWR 
Web 
Outer 
wing-fuselage fitting 
Spar 
Skin 
Skin 
Sealant 
Crack 
Spacer plate 
Inspection area 
Crack

### Page 8

MU-2  Service  Bulletin  
No. 107/57-005 DATE: May 3, 2016 
 
 
Page 8 of 14 
 
Figure 2: DETAILED INSPECTION AREA OF SPACER PLATE 
(Typical, LH side shown, RH side opposite.) 
  
Skin 
Skin 
Skin 
Spacer plate 
Spacer plate 
Outer 
wing-fuselage fitting 
Spar 
Spar 
Crack 
Hatched area is filled 
with sealant 
A 
 A 
SECTION A-A 
Crack 
Inspection 
area 
FWD 
OUT B/D 
(LH) 
LKG UP 
UPR 
OUT B/D 
(LH) 
W.S. 
580 
W.S. 
520

### Page 9 (OCR)

MU-2 Service Bulletin
No. 107/57-005  DATE: May 3, 2016
FRONT SPAR REF PLANE
FRONT SPAR - LOWER (REF)
TACK RIVET  (REF)
1 MS20426AD3-10  BRACKET
2 REOD  MS20426AD5-12 9 REOD
DOME NUT  MS20426AD4-5 6 REOD
DRILL #11 (4.85)
• NAS1473A3  1 REOD
(REMOVE) 14633H-020
9 MS20426AD3-10 2 REOD  MS20426AD5-7 3 REQD
€ MS20470AD5-12 2 REOD  MS20470AD5-9 6 REOD ®
TACK RIVET
® MS20470AD3-11
2 REQD
RIB ASSY (REF)
6 MS20470AD5-13
TACK RIVET
• MS20470AD3-7 1 REOD @
STIFFENER PANEL (REF)
NAS 1097AD4-9  16 REOD
/ C'SINK ON SPACER PLATE
AND SPAR CHORD.  NEAR SIDE FOR  MS20470AD5-7 9 REQD
MANUFACUTURED HEAD.
DO NOT INSTALL RIVETS
TO LAMINATED SHIM.
Spacer plate
. 4375 1 0020  017A-11102-13 1 REOD (LH)  017A-11102-14 1 REOD (RH)
17A-11102-5 1 REQD (LH)) (REMOVE  17A-11102-6 1 REOD (RH)
TACK RIVET
® MS20470AD3-10  LOWER SKIN (REF)
2 REQD
1S20470AD4-5 15 REQD
MS20470AD5  29 REOD
OUTBOARD
→ FWD J
LH SHOWN
RH OPPOSITE  6 : MS20426AD5 : UP  TO S/N 250
S/N 501 TO 575
VIEW LOOKING UP  MS20470AD5 : S/N 251 TO 466
S/N 576 & UP
3 : PEEL 003" LAMINATING AS REQUIRED
TO FILL GAP WITHIN ,005i PRIOR TO
BOLT INSTALLATION.
APPLY ZINC CHROMATE PRIMER TO
LAMINATED SHIM BEFORE INSTALLING.
2 : INSTALL UNDER NUT.
1 : INSTALL UndeR BOLT HEAD.
NOTES
Figure 3: INSTALLATION OF NEW SPACER PLATE (1/2)
(Typical, LH side shown, RH side opposite.)
Page 9 of 14

### Page 10 (OCR)

MU-2 Service  Bulletin
No. 107/57-005  DATE: May 3, 2016
NAS1203-13  2 REQD (REUSE)
NAS679A3W  2 REQD (REPLACE WITH NEW ONE)
800-0115-10  2 REQD (BETWEEN FITTING AND WASHER)
NAS1149D0316H 4 REQD
AN960D1OL  800-015-10  4 REOD} ‹REMOVE ›
FRONT SPAR REF PLANE  017A-11002-13 AS REQD (REUSE)
Shim
UPR SKIN (REF)
→
Inner support fitting
017A-11952-1  017A-11952-2  1 REQD (RH) | (REUSE)  1 REQD (LH)
NAS1103-13  10 REQD
NAS1103-16  2 REQD  (REUSE)
NAS1103-20  2 REQD
NAS679A3W  14 REQD (REPLACE WITH NEW ONE)
1 800-0115-10  14 REQD
NAS1149D0363H  14 REQU
800-015-10  14 REOD | (REMOVE ›
AN960D10  14 REQD
(NEAR SIDE FOR BOLT HEAD)
REAM . 4375 $00020  (11.11318.050)
MS20007-24 2 REQD  (REUSE)
H20-7  2 REQD
MS20002C7  2 REQD  (REPLACE WITH NEW ONE)
MS20002-7 2 REQD
(NEAR SIDE FOR BOLT HEAD)
Spacer plate
017A-11102-13/-14 (REF)
DOUBLER (REF)
STIFFENER PANEL (REF)
LWR SKIN (REF)
017A-11102-15 1 REQD
Laminated shim
3 : PEEL  003" LAMINATING AS REQUIRED
TO FILL GAP WITHIN .005" PRIOR TO
BOLT INSTALLATION.
APPLY ZINC CHROMATE PRIMER TO
LAMINATED SHIM BEFORE INSTALLING
@ : INSTALL UNDER NUT.
1 : INSTALL UNDER BOLT HEAD.
(REUSE)  - FWD
017A-11951-1  1 REQD (LH)  NOTES
017A-11951-2  1 REQD (RH)
Outer wing-fuselage fitting  SECT A-A
Figure 3: INSTALLATION OF NEW SPACER PLATE (2/2)
(Typical, LH side shown, RH side opposite.)
Page 10 of 14

### Page 11 (OCR)

MU-2 Service Bulletin
No. 107/57-005  DATE: May 3, 2016
9 Nut plate  • Tack rivet
1 Tack rivet
Note: Tack rivets and a nut plate are installed under the skin originally.
7 : INSTALL RIVET MS20426AD3 AS SHOWN.
MS20426AD3  MS20426AD3
C'SINK ON  C'SINK ON SKIN
SPACER PLATE
(REF)  FRONT  (REF)
SPACER PLATE  SPAR  SPACER PLATE
(SHOULD BE REMOVED)  (REF)  (NEW PART)
(BEFORE)  (AFTER)
8 : INSTALL RIVET MS20470AD3 AS SHOWN.
MS20426AD3  MS20470AD3
C'SINK ON
SPACER PLATE
(REF)  FRONT  (REF)
SPACER PLATE  SPAR  SPACER PLATE
(SHOULD BE REMOVED)  (REF)  (NEW PART)
(BEFORE )  ( AFTER)
›: INSTALL RIVET MS20426AD3 AND DOME NUT AS SHOWN.
MS20426AD3  SKIN  MS20426AD3
C'SINK ON  C'SINK ON SKIN
SPACER PLATE ,
(REF)  FRONT  (REF)
SPACER PLATE  SPAR  SPACER PLATE
(SHOULD BE REMOVED)  (REF)  (NEW PART)
DOME NUT
(BEFORE)  (REF)  ( AFTER)
Figure 4: INSTALLATION OF TACK RIVET AND NUT PLATE
(Typical, LH side shown, RH side opposite.)
Page 11 of 14

### Page 12 (OCR)

MU-2 Service Bulletin
No. 107/57-005  DATE: May 3, 2016
FRONT SPAR REF PLANE
BRACKET (REF)
RIB ASSY (REF)
Vo
STIFFENER PANEL (REF)
(REF)
017A-11951-1/-
LWR SKIN (REF)
017A-11102-13/-14 (REF)
017A-11102-15 (REF)
OUTBOARD
→ FWD -
SEALING
_H SHOWN
RH OPPOSITE
VIEW LOOKING UP
Figure 5: SEALING INSTRUCTION (1/3)
(Typical, LH side shown, RH side opposite.)
Page 12 of 14

### Page 13 (OCR)

MU-2  Service  Bulletin
No. 107/57-005  DATE: May 3, 2016
017A-11002-13 (REF)
FRONT SPAR REF PLANE
UPR SKIN (REF)
(REF) 01
1952-1/-2 (REF)
LWR SKIN (REF)
STIFFENER PANEL (REF)
\ 017A-11102-13/-14 (REF)
017A-11102-15 (REF)
6: APPLY BRUSH SEAL WITH AMS-S-8802, Class A.
UP  4 : FILL GAP, APPLY FAY SURFACE SEAL AND
→ FWD -  FILLET SEAL WITH AMS-S-8802, Class B.
SECT B-B
Figure 5: SEALING INSTRUCTION (2/3)
(Typical, LH side shown, RH side opposite.)
Page 13 of 14

### Page 14 (OCR)

MU-2 Service Bulletin
No. 107/57-005  DATE: May 3, 2016
FRONT SPAR REF PLANE
BRACKET (REF)
RIB ASSY (REF)
(REF)
017A-11102-13/-14
LWR SKIN (REF)
STIFFENER PANEL (REF)
SECT C-C
FRONT SPAR REF PLANE
(REF)
017A-11102
LWR SKIN (REF)
SECT D-D
(REF) 017A-11951-1/  017A-11952-1/-2 (REF)
520
580
BRACKET (REF)
: APPLY BRUSH SEAL WITH AMS-S-8802. Class A.
SECT E-E
> : FILL GaP, AppLy Fay SURFACE SEAL AND
FILLET SEAL WITH AMS-S-8802, Class B.
Figure 5: SEALING INSTRUCTION (3/3)
(Typical, LH side shown, RH side opposite.)
Page 14 of 14

### Page 15

4550 Jimmy Doolittle Dr.,  Addison, TX   75001  TEL: 972-248-3108  FAX:  972-248-3321 
 
 
Dear Owner/Operator: 
 
This form serves as Compliance Certification for MU-2 Service Bulletin No. 107/57-005 
Please complete and return to our address below, ATTN: Publications Dept., fax (972) 
248-3108. 
 
MU-2 Serial Number  _______ 
 
Registration Number  _______ 
 
Total Airframe Hours  _______ 
 
Owner’s Name  ___________ Operator’s Name __________________ 
 
Telephone No.   ___________ Telephone No.  __________________ 
 
I CERTIFY THAT THE ABOVE AIRPLANE HAS BEEN MODIFIED IN 
ACCORDANCE WITH MITSUBISHI HEAVY INDUSTRIES SERVICE BULLETIN 
NO. 107/57-005. 
 
Facility completing work: 
 
Name:  _________________  Telephone No. _____________________ 
 
Address: _________________  Fax No. ______________________ 
 
Date of work: _________________  Work Order #: ______________________ 
 
Date:  _________________  SIGNED: ______________________ 
         (Signature) 
      PRINTED NAME:___________________ 
       
      TITLE: ____________________________

### Page 16

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
