# Ontic Service Bulletin CC7-27-038: Revision R3

- Rights: © Ontic. Filed by the FAA in regulations.gov docket FAA-2026-2723; AD 2026-21-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Ontic Service Bulletin CC7-27-038](https://openairdocs.org/service-documents/ontic/cc7-27-038.md)
- Title as filed: Ontic SBCC7-27-038R3
- Pages: 13
- PDF: https://openairdocs.org/files/sha256/87/8d/878d25c26e2eb602c673c8e1c6c5d44b4625ab65561a26289aad3d97c130dde2
- Page: https://openairdocs.org/service-documents/ontic/cc7-27-038/file/878d25c26e2e

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

1176 TELECOM DRIVE •   CREEDMOOR, NC 27522 • (919) 956-4300
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
TO: HOLDERS OF SA227 COMMUTER CATEGORY SERIES SERVICE INFORMATION 
MANUALS
Attached is SA227 Commuter Category Series Service Bulletin CC7-27-038R3, INSPECTION 
OF DL5040M5, DL5040M6, and DL5040M8 PITCH TRIM ACTUATORS,    
Issued: July 29, 2024; Revised: January 27, 2026.
This service bulletin provides instructions to perform a time travel check and inspect for 
sealant integrity and corrosion to the DLM5040M5, DLM5040M6, and DLM5040M8 pitch 
trim actuators. The pitch trim actuators must be replaced if corrosion or other damage is 
found, if actuator travel speeds are not met, or if time in service without appropriate seals 
is exceeded. 
This revision updates actuator time check information as well as manpower estimates.
Please insert the attached Service Bulletin and replace the Chapter 27 Index pages.

### Page 2

Issued:  July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 1 of 10
SERVICE BULLETIN
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
SA227 SERIES
COMMUTER CATEGORY
FLIGHT CONTROLS
INSPECTION OF DL5040M5, DL5040M6, and DL5040M8 PITCH TRIM ACTUATORS
1. PLANNING INFORMATION
A. Eﬀ ectivity:
All SA227 Commuter Category Airplanes equipped with DL5040M5, DL5040M6, and 
DL5040M8 Pitch Trim Actuators. 
B. Reason:
Service experience has indicated susceptibility of the internal and external 
components of the DL5040M5, DL5040M6, and DL5040M8 Pitch Trim Actuators to 
corrosion. This Service Bulletin speciﬁ es inspections and functional checks of the 
Pitch Trim Actuators to ensure continued seal integrity on the actuators and absence 
of corrosion. 
 This revision to the service bulletin clari ﬁ es the repetitive time checks for the various 
diﬀ erent actuators and updates the manpower requirements.
C. Description:
Perform an initial and repetitive inspection / check of the DL5040M5, DL5040M6, 
and DL5040M8 Pitch Trim Actuators to check for corrosion and check actuator travel 
times. The tasks speciﬁ ed in this Service Bulletin are to be completed supplemental 
to the inspections speciﬁ ed in Service Letter CC7-SL-028 and Airworthiness 
Directive 2007-16-03. Compliance with the actuator travel time checks in Service 
Letter CC7-SL-028 for the DL5040M8 actuator can be used to satisfy the travel time 
check requirements in this Service Bulletin for the DL5040M8 actuator, as long as 
the inspection threshold and interval calendar time requirements are met. For any 
conﬂ ict between this Service Bulletin and the requirements of AD 2007-16-03, the 
AD shall take precedence. 
D. Compliance:
Mandatory. The initial action compliance time remains unchanged; refer to the original 
service bulletin for the date. Compliance time for repetitive action is de ﬁ ned in the 
current revision of the service bulletin.
NOTE:
Actions in this Service Bulletin are speciﬁ ed in terms of calendar time and ﬂ ight hours. 
For actions speciﬁ ed in terms of calendar time, time in service commences on the 
date that a new or overhauled actuator is installed on an airplane and is continuous 
thereafter until overhauled as speciﬁ ed in this Service Bulletin, whether it remains on 
the airplane or not.
For all airplanes, perform the following actions at the times speciﬁ ed; in the initial 
action column and the repetitive action column in Table 1 of this service bulletin.

### Page 3

Issued: July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 2 of 10
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
FLIGHT CONTROLS
Condition Initial Action Repetitive Action
I.  All DL5040M5,
    DL5040M6, and
    DL5040M8 actuator
    assemblies.
Within the next 1,000 ﬂ ight hours 
or 6 calendar months from the 
date of this Service Bulletin, 
whichever is sooner, determine if 
the actuator rod ends have been 
sealed as shown in Figure 3, 
Locations 1 and 2, of this Service 
Bulletin since the actuator was ini-
tially put into service. Perform the 
actions as speciﬁ ed in Conditions 
II, III or IV below.
II.  For actuators whose
     rod ends have been
     sealed as shown in
     Figure 3, Locations
     1 and 2, since put
     into service.
No additional initial action re-
quired.
A.
B.
For DL5040M5 actuators, every 250 
ﬂ ight hours or 6 months whichever 
occurs sooner and for DL5040M6 and 
DL5040M8 actuators, every 300 ﬂ ight 
hours or 6 months, whichever occurs 
sooner check the pitch trim actuators in 
accordance with Step 2.A, and
For all actuators, every 1,000 ﬂ ight 
hours or every 12 calendar months, 
whichever occurs sooner, inspect and 
seal the actuator per Step 2.B.
III.  For actuators whose    
      rod ends have not
      been sealed as 
      shown in Figure 3,
      Locations 1 and 2, 
      since put into service
      and have less than
      1,000 ﬂ ight hours or
      6 months calendar
      time in service, 
      whichever is less.
Prior to incurring 1,000 ﬂ ight hours 
or 6 months calendar time in ser-
vice on the actuator, whichever is 
less, inspect and seal the actuator 
per Step 2.B.
A.
B.
For DL5040M5 actuators, every 250 
ﬂ ight hours or 6 months whichever 
occurs sooner and for DL5040M6 and 
DL5040M8 actuators, every 300 ﬂ ight 
hours or 6 months, whichever occurs 
sooner check the pitch trim actuators in 
accordance with Step 2.A, and
For all actuators, every 1,000 ﬂ ight 
hours or every 12 calendar months, 
whichever occurs sooner, inspect and 
seal the actuator per Step 2.B.
IV.  For actuators whose 
      rod ends have not
      been sealed as 
      shown in Figure 3, 
      Locations 1 and 2, 
      since put into ser-
      vice and have 1,000 
      ﬂ ight hours or 6 
      months calendar time
      in service, whichever
      is less.
Replace the actuator with a new 
or overhauled actuator and install 
and seal the actuator per Step 
2.B.8).
A.
B.
For DL5040M5 actuators, every 250 
ﬂ ight hours or 6 months whichever 
occurs sooner and for DL5040M6 and 
DL5040M8 actuators, every 300 ﬂ ight 
hours or 6 months, whichever occurs 
sooner check the pitch trim actuators in 
accordance with Step 2.A, and
For all actuators, every 1,000 ﬂ ight 
hours or every 12 calendar months, 
whichever occurs sooner, inspect and 
seal the actuator per Step 2.B.
Table 1: Compliance Requirements

### Page 4

Issued:  July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 3 of 10
SERVICE BULLETIN
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
SA227 SERIES
COMMUTER CATEGORY
FLIGHT CONTROLS
NOTE:
Acceptable replacement pitch trim actuators part numbers are speciﬁ ed in Airworthiness 
Directive AD 2007-16-03. The term overhaul as applied in this Service Bulletin is an 
FAA approved procedure that de ﬁ nes the disassembly, inspection, troubleshooting, 
replacement of defective components, servicing, reassembly and functional testing of 
the pitch trim actuators. AD 2007-16-03 speciﬁ es the intervals for repetitively replacing 
the actuator with a new or overhauled actuator.
The following is an FAA-approved facility performing overhaul and repairs of Simmonds-
Precision Actuators. There may be other FAA approved facilities.
Contact Information:
World Class Accessory, Inc.
1130 Dividend Court
Peachtree City, GA 30269
Phone: (770) 631-2470
Fax: (770) 631-0664
Email:  repairs@worldclassaccessory.com 
Website: www.worldclassaccessory.com
E. Approval:
 The Engineering aspects were approved with the initial revision of this service bulletin. 
This revision only refers to previously FAA approved data. No additional FAA approvals 
are required.
F. Manpower:
Step 2.A and Step 2.B each require an estimated 3 direct man-hours by an experienced 
crew. If ﬁ llet sealant removal and reapplication is necessary, Step 2.B's estimate 
increases to 5 man-hours. Adjust estimates with operator task-hour data as needed.
G. Material - Cost and Availability:
  Contact the Ontic Sales Team for cost and availability: metroparts@ontic.com.
H. Tooling-Price and Availability:
Refer to the SA227 Commuter Category Series Maintenance Manual for required tooling 
to conduct actuators free play and time / racheting checks.

### Page 5

Issued: July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 4 of 10
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
FLIGHT CONTROLS
I. Weight and Balance:
Negligible
NOTE
: It is recommended the aircraft operating weight be re-established after
incorporating 20 service bulletins classi ﬁ 
ed as having negligible impact on 
aircraft weight and balance. This recommendation is derived from data provided 
in FAA Advisory Circular 120-27.  
J. References:
• SA227 Commuter Category Structural Repair Manual, Chapter 51-30-02 and 51-
30-03.
• SA227 Commuter Category Maintenance Manual, Chapter 27-40-10.
•
 SA227 Commuter Category Phase Inspection Manual, Form 608, Detailed Inspection.
• SA227 Commuter Category Letter Check Inspection Manual, Letter Check D.
• Ontic Drawings 27-19008, 27-43027, 32-8203.
• Ontic Report R1529.
• Ontic Technical Memorandums M-2225A, M-2231, M-2320, and M-2329.
NOTE: References are for manufacturers’ use only.
K. Other Publications Aﬀ ected: None.
2. ACCOMPLISHMENT INSTRUCTIONS
A.
Pitch Trim Actuator Time Travel Check
1) Record pitch trim actuator part number, serial number, date and total
time in service for the actuator since last overhaul.
2) Clear tail of all personnel and equipment.
3) Connect external electrical power to aircraft.
(Refer to SA227 Commuter Category AMM, 24-40-00).
4) Ensure LH and RH essential bus voltages for DL5040M5 (Mod 1 and 2),
DL5040M6, and DL5040M8 actuators are 29.0 + 0.0 /-0.5 VDC.
NOTE:  Prior to performing actuator travel time check, verify proper adjustment of
  horizontal stabilizer electrical stops (limit switches) IAW SA227 
  Commuter Category AMM, Section 27-40-10, Step 4. C. Adjustment -  
  Electrical/Mechanical Stops in this section.

### Page 6

Issued:  July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 5 of 10
SERVICE BULLETIN
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
SA227 SERIES
COMMUTER CATEGORY
FLIGHT CONTROLS
 5) Place TRIM SELECT switch on COPILOT.
 6) Using copilot control wheel trim switch, run horizontal stabilizer to full 
  aircraft nose up position (leading edge of stabilizer will be full down).
NOTE: Travel time begins at the ﬁ rst trim in motion beep and ends at the last beep.
 7) Using copilot control wheel trim switch, run stabilizer to extreme aircraft
   NOSE DOWN position (leading edge of stabilizer will be full up) and record
  time of travel. Verify travel time is:
a. 18 to 25 seconds for P/N DL5040M5, Mod 1
b. 18 to 27 seconds for P/N DL5040M5, Mod 2
c. 18 to 27 seconds for P/N DL5040M6
d. 25 to 30 seconds for P/N DL5040M8
 8) Using copilot control wheel trim switch, run stabilizer to extreme aircraft
  NOSE UP position (leading edge of stabilizer will be full down) and record
  time of travel. Verify travel time is:
a. 18 to 25 seconds for P/N DL5040M5, Mod 1
b. 18 to 27 seconds for P/N DL5040M5, Mod 2
c. 18 to 27 seconds for P/N DL5040M6
d. 25 to 30 seconds for P/N DL5040M8
 9) Using pilot control wheel trim switch, repeat steps (6) through (8).
 10) Maximum allowable split between travel time from full up to full down and
  from full down to full up may not exceed four seconds on either side.
 11) If travel time is not within speciﬁ  ed limits:
  a. Disconnect actuator rod of faster side (pilot or copilot).
  b. Check stabilizer travel time of the remaining connected actuator rod.
   i. If travel time is now within limits, the actuator installation is
    suspect. Check actuator installation for misalignment and/or
    check horizontal stabilizer for binding.
  c. Disconnect other actuator rod end and check time required for each
   actuator rod to extend and retract fully.
   i. If actuator rods meet travel time criteria, check actuator
    installation for misalignment.
   ii. If either actuator rod does not meet travel time criteria, 
    replace the actuator.

### Page 7

Issued: July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 6 of 10
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
FLIGHT CONTROLS
  12) Disconnect external electrical power from aircraft. 
  (Refer to SA227 Commuter Category AMM 24-40-00).
 13) Proceed to Step 2.C.
 B. Inspection of Pitch Trim Actuators
  1)  Record pitch trim actuator part number, serial number, date and total time in
   service for the actuator since last overhaul.
  2)  Lower horizontal stabilizer to the full leading edge down position. 
  3)  Using good lighting (100 FC minimum) and using inspection mirrors as 
   required, perform a general visual inspection of the actuator checking for
   signs of corrosion or other damage.
  4)  Using good lighting (100 FC minimum) and inspection mirrors, perform 
 a detailed visual inspection of the juncture of the actuator casing with the  
base of the actuator (see Figure 2). Check for signs of moisture / ﬂ uid leaking  
from inside the actuator, signs of corrosion or other damage. Indications 
of any of these requires replacement of actuator with a new or overhauled 
actuator.
  5)  There are two weep holes on the aft, lower surface of the actuator casing.
   Inspect the two weep holes to ensure that they are clear of foreign matter or
   debris.
  6)  Using good lighting (100 FC minimum), perform a detailed visual inspection 
   of the actuator two upper rod ends, jam nuts, locking washers, lock wire 
   and moving tubes checking (see Figure 3) for signs of corrosion or other
   damage. If there are indications of corrosion or other damage, replace 
   with a new or overhauled actuator.
  7)  For each ram of the actuator, check the integrity of the sealant shown in 
   Figure 3. If there is no sealant present, then proceed to Step 2.B.8) or if
    integrity of the sealant is compromised remove the defective sealant and
    proceed to Step 2.B.8). If the integrity of the seal is acceptable, proceed to  
  Step 2.C.
  8)  If no sealant is present or existing sealant is cracked/missing or 
    compromised, as shown in Figure 3, then for each ram of the actuator, clean  
  the area and/or remove the old sealant around the threads of the rod end, 
   the jam nut, the lock washer and the insert per SRM 51-30-02 and apply 
   sealant per SRM 51-30-03 to the exposed threads of the rod end, in the rod 
   end keyway, to the top and bottom of the lock washer and encapsulate the
   nut (see Figure 3). When applying sealant between the lock washer and the

### Page 8

Issued:  July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 7 of 10
SERVICE BULLETIN
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
SA227 SERIES
COMMUTER CATEGORY
FLIGHT CONTROLS
   moving tube, protect the circumference of the moving tube from sealant and
    ﬁ llet seal between the top of the moving tube and the bottom of the lock 
   washer as shown in Figure 3. Proceed to Step 2.C.
C. Return to Service
1)  Perform operational check of all systems a ﬀ ected by this Service Bulletin 
 in accordance  with applicable sections of the SA227 Commuter Category
 Maintenance Manual (MM).
 a. For each actuator returned from overhaul or new, once installed in 
  the aircraft, and rigging/adjustment is complete, apply sealant to 
  each ram rod end per Step 2.B.8).
2)  Reinstall all panels removed using retained hardware. Replace any 
 damaged hardware with new hardware.
3)  Complete aircraft records in accordance with 14 CFR 43.9.
4)  Complete and return service bulletin Compliance Form to Ontic Engineering 
 and Manufacturing Technical Support Department. 
 Email: Metroliner@Ontic.com.
3. MATERIAL LISTING
Location / Item Part Number Alternate P/N Quantity
At Horizontal Pitch Trim 
Actuator:
Pitch Trim Actuator  DL5040M5 - 1
Pitch Trim Actuator  DL5040M6 - 1
Pitch Trim Actuator  DL5040M8 - 1
NOTE: Contact an FAA authorized facility for overhaul of actuator.

### Page 9

Issued: July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 8 of 10
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
FLIGHT CONTROLS
General External Features of Pitch Trim Actuator
Figure 1
Electronic Connectors
End Fitting
Casing
Moveable Tube
Housing Cap
Moveable Tube
Housing 
Jam Nut
Rod Ends

### Page 10

Issued:  July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 9 of 10
SERVICE BULLETIN
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
SA227 SERIES
COMMUTER CATEGORY
FLIGHT CONTROLS
Inspection of Actuator Casing Lower Seal Joint
Figure 2
Actuator
Casing
Juncture of 
Actuator
 Casing with 
Base of Actuator

### Page 11

Issued: July 29, 2024
Revised:  January 27, 2026
CC7-27-038R3
Page 10 of 10
SERVICE BULLETIN
SA227 SERIES
COMMUTER CATEGORY
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
FLIGHT CONTROLS
Rod End
Fillet Seal
Location 1
Jam Nut
Lock Washer
Stop Nut
Housing 
Moving Tube
Insert
Fillet Seal
Location 2
Fillet Seal
Location 3
Inspection of Actuator Upper Components and Seal Joints
Figure 3
Moving Tube.
No sealant 
on surface of 
Moving Tube 
shown in this 
view.
Stop Nut
Insert
Jam Nut
Rod End
Lock Washer
Top of Moving Tube.
Fillet seal between 
this surface and lock 
washer.
Circumference of 
Moving Tube. No 
sealant on this surface.

### Page 12

SERVICE BULLETIN COMPLIANCE FORM
CC7-27-038R3
TO: OPERATOR OR SER VICE FACILITY ACCOMPLISHING BULLETIN
Please complete this compliance form, and  mail according to the instructions on the 
reverse side.
Thank you for returning this form.
**************************************************************************************************
Aircraft Model Aircraft Serial Number 
Bulletin Issue Date  Revision Date 
Aircraft Registration Number 
Operator/Owner
Time on Aircraft 
Date Accomplished 
Comments
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

### Page 13

------------------------------------------------------FOLD HERE TO MAIL-------------------------------------------------------
------------------------------------------------------FOLD HERE TO MAIL-------------------------------------------------------
KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ
PLACE
STAMP
HERE
ONTIC ENGINEERING AND MANUFACTURING, INC.
1176 TELECOM DRIVE
CREEDMOOR, NC 27522
ATTN: DOCUMENT CONTROL

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
