# Piaggio Mandatory Service Bulletin 80-0345: No revision named

- Rights: © Piaggio. Filed by the FAA in regulations.gov docket FAA-2013-0527; AD 2013-18-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Piaggio Mandatory Service Bulletin 80-0345](https://openairdocs.org/service-documents/piaggio/sb-80-0345.md)
- Title as filed: U.S. DOT/FAA - Piaggio Service Bulletin 80-0345
- Pages: 9
- PDF: https://openairdocs.org/files/sha256/3b/ee/3beedce8687e5a716c2c09fe25df7497114db28df6c121976ad34faeb0afcdfb
- Page: https://openairdocs.org/service-documents/piaggio/sb-80-0345/file/3beedce8687e

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
The EASA states mandatory compliance with inspections, modifications or technical directives and
related time compliance by means of relevant Airworthiness Directives.
SERVICE BULLETIN (MANDATORY) N.: 80-0345 REV.0  ATA CHAPTER: 32-00
MODIFICATION N.: N/A
TITLE: MAIN LANDING GEAR LEVER HINGE FITTING INSPECTION
REVISION STATUS OF THE BULLETIN
This Service Bulletin is at the original issue and consists of 9 pages, plus Appendix A (Messier-
Dowty Ltd. Service Bulletin no. P180-32-32, 1+8 pages).
1. PLANNING INFORMATION
A. EFFECTIVITY
Piaggio Aero Industries P180 Avanti and Avanti II Manufacturer's Serial Number (MSN):
1002; from 1004 and up, installing Main Landing Gear 201416 series, 201459 series and
201034 series.
B. CONCURRENT REQUIREMENTS
N/A
C. REASON
During a scheduled maintenance inspection, evidence of cracks has been identified on the
Main Landing Gear (MLG) lever hinge fitting (LHF) in correspondence of the joint between
the hinge pin sub-assembly and the lock pin. This condition, if not detected and corrected,
could lead to a serious structural defect of the Main Landing Gear, possibly resulting in
damage to the aircraft and/or injury to the occupants.
As a temporary corrective action, additional inspections are required on in-service Main
Landing Gear Lever Hinge Fittings.
Regulatory action is expected.
D. DESCRIPTION
General
This Service Bulletin consist of the following additional checks:
1. Check for freedom of rotation of the main landing gear wheel lever sub-
assembly
2. Repetitive visual inspection of the main landing gear lever hinge fittings
3. Repetitive fluorescent penetrant inspections of the main landing gear lever hinge
fittings.
Depending on inspection results, replacement of the failed item with a serviceable one may
be required.
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. 0  Date:  Page:  1 of 9

### Page 2 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
E. COMPLIANCE
This MANDATORY Service Bulletin shall be accomplished as follows:
- Part 1 - Check for freedom of rotation of the main landing gear wheel lever sub-
assemblies: this one-off" check is required on all MLG installed on airplanes
listed under "Effectivity" section of this Service Bulletin; unless already done, it
is required within 200 landings, or three (3) months, whichever occurs first, from
the issue date of this Service Bulletin, and following replacement of a MLG.
Part 2 - Visual inspection of the main landing gear lever hinge fittings: this check
is required on all Lever Hinge Fittings (part of MLG), when installed on
airplanes listed under "Effectivity" section of this Service Bulletin. Unless
already done in the previous 200 landings, perform this check initially as
specified in Table 1. If the "Check for freedom of rotation" described in part 1 of
the accomplishment instruction does not pass, initially perform this check before
next flight of the LF installed on the MLG that did not pass the test. After
initial inspection, repeat the check at intervals not to exceed 200 landings, until
retirement from service of the LHF, as long as this Service Bulletin is active.
Part 3 - Fluorescent penetrant inspections of the main landing gear lever hinge
fittings: this check is required on all Lever Hinge Fittings (part of MLG), when
installed on airplanes listed under "Effectivity" section of this Service Bulletin.
Unless already done in the previous 750 landings, perform this check initially as
specified in Table 1. If the "Check for freedom of rotation" described in part 1 of
the accomplishment instruction does not pass, initially perform this check before
next flight of the LHF installed on the MLG that did not pass the test. After
initial inspection, repeat the check at intervals not to exceed 750 landings, until
retirement from service of the LHF, as long as this Service Bulletin is active.
LHF Cycles since new (CSN)  Compliance required
CSN ≤ 2300  Within 2500 CSN
2300 < CSN < 2500  Within 200 landings from the issue date of this Service
Bulletin
CSN ≥ 2500  Within 200 landings or three (3) months (whichever
occurs first) from the issue date of this Service Bulletin
Table 1
NOTE: RH and LH MLG may have different compliance limits.
In compliance with this Service Bulletin, please complete the attached Confirmation Slip and
send it back to Piaggio Aero Industries S.p.A. - Product Support Department.
Original Issue: 20 September 2012  Service Bulletin:  80-0345
Rev. N. 0  Date:  Page:  2 of 9

### Page 3 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
F. APPROVAL
The technical content of this Service Bulletin has been approved under the Authority of
DOA No EASA.21J.220.
G. MANPOWER
This MANDATORY Service Bulletin may be accomplished in approximately:
Part 1 - 2 man-hours (MH) per airplane.
Part 2 - 2 man-hours (MH) per airplane.
Part 3 - 7 man-hours (MH) per airplane.
H. TECHNICAL INFORMATION
For questions concerning the technical content of this Service Bulletin, please contact:
Piaggio Aero Industries - Product Support Department
Via Cibrario, 4 - 16154 Genoa, Italy
Fax No. : + 39 010 6481 374
E-mail: tech.support@piaggioaero.it
I. MATERIAL - COST AND AVAILABILITY
Please contact:
Piaggio Aero Industries - Customer Support Department
Via Cibrario, 4 - 16154 Genoa, Italy
Telephone No.: +39 010 6481 800
Fax No.: +39 010 6481 891
E-Mail: commercialcustomersupport@piaggioaero.it
J. TOOLING - COST AND AVAILABILITY
No special tools are required.
K. WEIGHT AND BALANCE
N/A
L. ELECTRICAL LOAD DATA
N/A
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. 0  Date:  Page:  3 of 9

### Page 4 (OCR)

PIAGGIO/  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
M. REFERENCES
Document Title  Document Number  Chapter/Section
Aircraft Maintenance Manual (AMM)  180-MAN-0200-01105 (Avanti II)  9066 (Avanti)  32-11-00  07-10-00
Messier Dowty Ltd. - Service Bulletin  P180-32-32
N. PUBLICATIONS AFFECTED
N/A
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. 0  Date:  Page:  4 of 9

### Page 5 (OCR)

PIAGGIO T  AERO  Via Cibrario, 4 - 16154 Genoa, Italy  PIAGGIO AERO INDUSTRIES S.p.A.
Product Support Department
2. ACCOMPLISHMENT INSTRUCTIONS
Procedure
NOTE
WITHIN THE SCOPE OF THIS SERVICE BULLETIN, A MAIN
LANDING GEAR IS DEEMED SERVICEABLE IF:
- It passes the check for freedom of rotation described in Part 1 of the
Accomplishment Instructions, and following inspections described in
Part 2 and Part 3 of the Accomplishment Instructions, when performed in
accordance with compliance section, no cracks are identified on its Lever
Hinge Fitting.
NOTE
WITHIN THE SCOPE OF THIS SERVICE BULLETIN, "REPLACE
THE MAIN LANDING GEAR WITH A SERVICEABLE ONE"
MEANS:
- Remove the unserviceable MLG and replace it with a different
serviceable MLG
OR
- Rework the unserviceable MLG until it passes the check for freedom of
rotation and, following inspections described in Part 2 and Part 3 of the
Accomplishment Instructions, no cracks are identified on its Lever Hinge
Fitting.
OR
- Replace the cracked LHF in the unserviceable MLG with a new LHF
and, after LHF replacement, check the MLG for freedom of rotation.
Part 1 - Check for freedom of rotation of the main landing gear wheel lever subassemblies
(1) Jack the aircraft (refer to AMM Ch. 07-10-00).
(2) With reference to figure 2, perform a visual inspection for cracks of the main landing
gear lever hinge fitting, in the area around the slot. If necessary, clean the area with a
cloth before performing the inspection.
(3) If, following the inspection, cracks are identified, replace the main landing gear with a
serviceable one before next flight. Complete the attached Confirmation Slip and send it
back to Piaggio Aero Industries S.p.A. - Product Support Department.
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. 0  Date:  Page:  5 of 9

### Page 6 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
(4) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform
*Procedure A", steps 2 to 6.
(5) If the landing gear has not passed the test:
a. If the Lever Hinge Fitting has less than 2500 landings since new (CSN),
using an indelible pen mark the LHF as "inspect as per SB-80-0345", then
replace the affected landing gear with a serviceable one before next flight.
Make a note, recording type of inspection, date of inspection and inspection
results, in aircraft log-book and in the affected landing gear documentation.
Complete the attached Confirmation Slip and send it back to Piaggio Aero
Industries S.p.A. - Product Support Department.
CAUTION: The LHF installed on affected MLG must be inspected in
accordance with the compliance section of this Service Bulletin.
b. If the Lever Hinge Fitting has 2500 or more landings since new (CSN),
replace the affected landing gear with a serviceable one before next flight.
Make a note, recording type of inspection, date of inspection and inspection
results, in aircraft log-book and in the affected landing gear documentation.
Complete the attached Confirmation Slip and send it back to Piaggio Aero
Industries S.p.A. - Product Support Department.
CAUTION: The LF installed on affected MLG must be inspected in
accordance with the compliance section of this Service Bulletin.
(6) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).
(7) Make an appropriate entry in the airplane logbook to show compliance with this
section of this Service Bulletin.
Part 2 - Visual inspection of the main landing gear lever hinge fittings
(8) Jack the aircraft (refer to AMM Ch. 07-10-00).
(9) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform
"Procedure B", steps 2 to 5
(10) If, following the inspection, cracks are identified, replace the main landing gear with a
serviceable one before next flight. Complete the attached Confirmation Slip and send it
back to Piaggio Aero Industries S.p.A. - Product Support Department.
(11) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).
Original Issue: 20 September 2012  Service Bulletin:  80-0345
Rev. N. 0  Date:  Page:  6 of 9

### Page 7 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
(12) Make an appropriate entry in the airplane logbook to show compliance with this
section of this Service Bulletin.
Part 3 - Fluorescent penetrant inspections of the main landing gear lever hinge fittings
(13) Jack the aircraft (refer to AMM Ch. 07-10-00).
(14) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform
"Procedure C", steps 2 to 8
(15)If, following the inspection, cracks are identified, replace the main landing gear with a
serviceable one before next flight.
(16) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).
(17) Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries
S.p.A. - Product Support Department.
(18)Make an appropriate entry in the airplane logbook to show compliance with this
section of this Service Bulletin.
LEVER HINGE
_ PINTLE PIN
SUB-ASS
WEIGHT
CK ABSORBER
SUB-ASSEMBLY
AXLE RETAINING PIN
AXLE NUT
FIGURE 1 - Main Landing Gear: lever hinge fitting (LH shown).
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. 0  Date:  Page:  7 of 9

### Page 8 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
FIGURE 2 - Main Landing Gear LHF - crack.
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. O  Date:  Page:  8 of 9

### Page 9 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
3. MATERIAL INFORMATION
A. LIST OF MODIFICATION KIT COMPONENTS
N/A
B. LIST OF MATERIALS - OPERATOR SUPPLIED
N/A
C. LIST OF TOOLS
N/A
D. DISPOSAL OF REMOVED PART
N/A
E. WARRANTY CREDIT PROGRAM
N/A
4. WARNING - PROPRIETARY RIGHTS
This bulletin contains proprietary information of Piaggio Aero Industries S.p.A. (PAI),
which PAI provides in confidence and solely for the purposes of supporting PAI products
and providing applicable information regarding the proper use, maintenance, inspection,
repair, servicing and parts application of PAI products. Neither this bulletin nor any
information in it may be disclosed to others, or used for any other purpose, including,
without limitation, to design, create, develop, reproduce, manufacture or derive any design,
part, product, material, process, modification, configuration change or repair, or obtain any
government approval to do so. This material is the exclusive property of Piaggio Aero
Industries S.p.A. and therefore shall not be reproduced, used or disclosed to others except as
authorized by contract with Piaggio Aero Industries S.p.A. or without the written permission
of Piaggio Aero Industries S.p.A..
Original Issue: 20 September 2012  Service Bulletin: 80-0345
Rev. N. O  Date:  Page:  9 of 9

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
