# Piaggio Mandatory Service Bulletin 80-0381: No revision named

- Rights: © Piaggio. Filed by the FAA in regulations.gov docket FAA-2013-0964; AD 2014-03-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Piaggio Mandatory Service Bulletin 80-0381](https://openairdocs.org/service-documents/piaggio/sb-80-0381.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin 80-0381
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/4b/84/4b84645d26a2b668377d2e4b9c8fa5d48a24482e4880ecbd4d6d06d9e27007dc
- Page: https://openairdocs.org/service-documents/piaggio/sb-80-0381/file/4b84645d26a2

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO p  AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
The EASA states mandatory compliance with inspections, modifications or technical directives and
related time compliance by means of relevant Airworthiness Directives.
SERVICE BULLETIN (MANDATORY) N.: 80-0381  REV.O ATA CHAPTER: 27-00
MODIFICATION N.: N/A
TITLE: HORIZONTAL STABILIZER TO ELEVATOR CLEARANCE VERIFICATION AND
MINOR REWORK
REVISION STATUS OF THE BULLETIN
This Service Bulletin is at the original issue and consists of 9 pages.
1. PLANNING INFORMATION
A. EFFECTIVITY
Piaggio Aero Industries P180 Avanti and Avanti II Manufacturer's Serial Number (MSN):
1002 and from 1004 thru 1231.
B. CONCURRENT REQUIREMENTS
N/A.
C. REASON
The spanwise clearance between the horizontal stabilizer end rib and the elevator horn was
measured lower than minimum on an in-service aircraft. According to preliminary
investigation, similar installation may be found on airplanes listed under effectivity section
of this Service Bulletin.
A procedure to measure the clearance and to restore an acceptable margin is provided in this
Service Bulletin.
D. DESCRIPTION
General
This Service Bulletin consists of the following actions:
Part A
• Measurement of the clearance between the elevator horn and the horizontal stabilizer
tip rib
Part B (if applicable, should the clearance result below the minimum allowed)
• Elevator removal
• Adjustment of the Elevator Bellcrank installation;
• Elevator installation and final check of the clearance;
Part C
• Data reporting to Piaggio Aero Technical Support.
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  1 of 9

### Page 2 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
E. COMPLIANCE
This Service Bulletin shall be accomplished as follows:
- Perform this Service Bulletin within 200FH or 12 months, whichever occurs first, from
the issue date of this Service Bulletin.
The clearance check (refer to Accomplishment Instructions - Part A) may not be performed
if all the following conditions are met:
- The minimum clearance was measured, on both LH and RH sides, during the previous 3
month from the issue date of this Service Bulletin.
- Measured clearance was at least 5 mm on both sides.
Part C shall in any case be accomplished.
In compliance with this Service Bulletin, please complete the attached Confirmation Slip and
send it back to Piaggio Aero Industries S.p.A. - Product Support Department.
F. APPROVAL
The technical content of this Service Bulletin has been approved under the Authority of
DOA No EASA.21J.220.
G. MANPOWER
This MANDATORY Service Bulletin may be accomplished in approximately:
- Part A+C: 1 man-hour (MH).
- Part B (if required): 4 man-hours (MH).
H. TECHNICAL INFORMATION
For questions concerning the technical content of this Service Bulletin, please contact:
Piaggio Aero Industries - Product Support Department
Via Cibrario, 4 - 16154 Genoa, Italy
Fax No. : + 39 010 6481 374
E-mail: tech.support@piaggioaero.it
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  2 of 9

### Page 3 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
I. MATERIAL - COST AND AVAILABILITY
For pricing, availability and scheduling, please contact:
- for customers and operators in Europe, Asia and RoW
e-mail:  spareparts@piaggioaero.it
telephone:  (+39) 010 6481 889
fax:  (+39) 010 6481 891
- for customers and operators in the Americas
e-mail:  SparepartsPAM@piaggioamerica.com
telephone :  (+1) 561 253 0104
fax:  (+1) 561 683 5513
J. TOOLING - COST AND AVAILABILITY
N/A
K. WEIGHT AND BALANCE
N/A
L. ELECTRICAL LOAD DATA
N/A
M. REFERENCES
Document Title  Document Number  Chapter/Section
Avanti Aircraft Maintenance Manual
(AMM)  9069  27-30-00
27-40-00
Avanti II Aircraft Maintenance  Manual (AMM)  180-MAN-0200-01105  55-10-00
N. PUBLICATIONS AFFECTED
N/A
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  3 of 9

### Page 4 (OCR)

PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO/
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
2. ACCOMPLISHMENT INSTRUCTIONS
Procedure
PART A - Clearance check
NOTE: WITHIN THE SCOPE OF THIS SERVICE BULLETIN, "ELEVATOR
IN NEUTRAL POSITION" MEANS THAT THE ELEVATOR LOWER
SURFACE IS ALIGNED WITH THE HORIZONTAL STABILIZER
LOWER SURFACE.
1. With the elevators in neutral position (elevator at angle = 0°), measure the minimum
clearance between the LH and RH elevator horns (see Fig. 1) and the horizontal
stabilizer (HS) end ribs. You may use a cylindrical rod (or equivalent), verifying it
moves freely across the entire length of the exposed area.
2.  Record the values in the table on the confirmation sheet.
Based on the clearance values:
If the minimum value is at least 5mm or more on both HS sides, leave the
structure as it is. Mark "Not necessary" on Part B of the confirmation sheet
and send it back to Piaggio Aero, then proceed with Part C of this Service
Bulletin.
If the minimum clearance is less than 5mm on any HS side, perform Part B
of this Service Bulletin on RH and/or LH HS side.
5mm MIN
Fig. 1 - Clearance measurement
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  4 of 9

### Page 5 (OCR)

PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
PART B - Minor rework
NOTE: THE FOLLOWING PROCEDURE MAY BE APPLIED ON RH AND LH
SIDE OF THE TAIL PLANE, AS REQUIRED
Remove the rear fairing from the top of the vertical stabilizer.
5. Remove the elevator in accordance with AMM chap. 27-30-00.
Verify if the countersunk washer P/N MS20002C6 (see Fig. 2, Fig. 3) is installed on
elevator. If the washer is not installed, proceed with step (7), otherwise proceed with
step (8).
washer P/N MS20002C6  N. 2 threads minimum
out of the nut
• 2 NUT
• 3 WASHER
BEARING
Elevator to stabilizer
distance
ELEVATOR BELLCRANK -  5 BOLT
7 NUT
6 WASHER
Fig. 2 - Detailed sketch of the elevator bellcrank
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  5 of 9

### Page 6 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
Countersunk
washer
MS20002C6
(countersink  Elevator body
towards the
elevator body)
Fig. 3 - Picture of the elevator bellcrank with the countersunk washer installed
NOTE: THE WASHER SHALL BE LOCKED TO THE ELEVATOR
BELLCRANK WITH LOCTITE (RC680, 222 OR EQUIVALENT)
7. If, following step 6, countersunk washer P/N MS20002C6 is found not installed,
install a new countersunk washer P/N MS20002C6, then temporary install the
elevator and repeat step 1. If the minimum clearance is at least 5 mm, go to step (9),
otherwise proceed with step (8).
NOTE: THE NEW WASHER P/N MS20002-6 SHALL BE LOCKED TO THE
EXISTING WASHER P/N MS20002C6 WITH LOCTITE (RC680, 222
OR EQUIVALENT)
NOTE: DURING ELEVATOR INSTALLATION, MAKE SURE THAT THERE
ARE AT LEAST N. 2 THREADS OUT OF THE NUT (SEE Fig. 2)
FIXING THE ELEVATOR TO THE BUSHING/STABILIZER ASSY.
8. If, following step (6), the countersunk washer P/N MS20002C6 is found installed, or
if required after accomplishment of step (7), add a new washer plain P/N MS20002-6
(plain) to the existing one in order to increase the distance between the elevator and
the stabilizer by 2mm (see Fig. 4, Fig. 5).
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  6 of 9

### Page 7 (OCR)

PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
Plain washer
MS20002-6
Countersink
Fig. 4 - Picture of the elevator bellcrank with the countersunk and plain washers installed
Plain washer
MS20002-6
Countersunk
washer
MS20002C6
(countersink
towards the
elevator body)
Fig. 5 - Picture of the elevator bellcrank with the countersunk and plain washers installed
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  7 of 9

### Page 8 (OCR)

PIAGGIO/  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
9. Install the elevator in accordance with AMM chap. 27-30-00
10. Repeat step (1) to make sure the minimum clearance is at least 5 mm.
11. Install the top fin fairing aft.
PART C - Data Reporting to Piaggio Aero Industries
12. Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries
S.p.a. - Product Support Department.
13. Make an opportune entry in the airplane logbook to show compliance with this
Service Bulletin.
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0 Date:  Page:  8 of 9

### Page 9 (OCR)

PIAGGIO  PIAGGIO AERO INDUSTRIES S.p.A.
AERO  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
3. MATERIAL INFORMATION
A. LIST OF MODIFICATION KIT COMPONENTS
B. LIST OF MATERIALS - OPERATOR SUPPLIED
Part/Number  Specification  Supplier  Qty.  Designation
MS20002C6  Standard/Any Source  A/R (max 2)  Washer - countersunk
MS20002-6  Standard/Any Source  A/R (max 2)  Washer - Plain
loctite  Standard/Any Source  A/R
C. LIST OF TOOLS
N/A
D. DISPOSAL OF REMOVED PART
N/A
E. WARRANTY CREDIT PROGRAM
N/A
4. WARNING - PROPRIETARY RIGHTS
This bulletin contains proprietary information of Piaggio Aero Industries S.p.A. (PAI),
which PAI provides in confidence and solely for the purposes of supporting PAI products
and providing applicable information regarding the proper use, maintenance, inspection,
repair, servicing and parts application of PAI products. Neither this bulletin nor any
information in it may be disclosed to others, or used for any other purpose, including,
without limitation, to design, create, develop, reproduce, manufacture or derive any design,
part, product, material, process, modification, configuration change or repair, or obtain any
government approval to do so. This material is the exclusive property of Piaggio Aero
Industries S.p.A. and therefore shall not be reproduced, used or disclosed to others except as
authorized by contract with Piaggio Aero Industries S.p.A. or without the written permission
of Piaggio Aero Industries S.p.A.
Original Issue: May 02, 2013  Service Bulletin:  80-0381
Rev. N. 0  Date:  Page:  9 of 9

### Page 10 (OCR)

PIAGGIO AERO INDUSTRIES S.p.A.
PIAGERO P  Via Cibrario, 4 - 16154 Genoa, Italy
Product Support Department
CONFIRMATION SLIP
Service Bulletin Accomplishment  SB-0381 Rev.0
A/C S/N:  A/C Flight Hours:  A/C LGDS:  A/C Registration:
Date:
Accomplished by:
Signature
INSPECTION RESULTS:
LH side  RH side
PART A - Clearance check  _mm  mm
• Done  • Done
PART B - Minor rework
• Not necessary  • Not necessary

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
