# Pilatus Service Bulletin PC-6 53-003: Revision 1

- Rights: © Pilatus Aircraft Ltd. Filed by the FAA in regulations.gov docket FAA-2016-9356; AD 2016-22-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Pilatus Service Bulletin PC-6 53-003](https://openairdocs.org/service-documents/pilatus/pc6-53-003.md)
- Title as filed: PC-6_SB 53-003 R1
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/ae/c0/aec07bd235a658007ac37936668ad65a7649e56c5bcc9f4e2eed5405c869beca
- Page: https://openairdocs.org/service-documents/pilatus/pc6-53-003/file/aec07bd235a6

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin No: 53-003 Ref No: 215
Modification No: INSPECTION ATA Chapter: 53
SERVICE BULLETIN
PILATUS AIRCRAFT LTD. STANS, SWITZERLAND
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 1 of 24
FUSELAGE - REAR FUSELAGE
STABILIZER-TRIM ATTACHMENT COMPONENTS - INSPECTION
1. Planning Information
A. Effectivity
Pilatus PC-6 Series aircraft MSNs 337 thru 1005. 
Fairchild built PC-6 aircraft MSNs 2001 thru 2092.
All PC-6 horizontal stabilizer assemblies, stabilizer control-system fittings, connecting pieces, 
bearing supports and bearing forks held as spares.
B. Concurrent Requirements
None.
This Service Bulletin applies to the Post SB 53-001 Revision 1 configuration.
C. Reason
(1) Problem
Wear and cracks have been reported in the following Post SB 53-001 R1 stabilizer-trim 
attachment and structural components:
• Fitting (116.40.06.112) or (116.40.06.033)  in aircraft with electrical horizontal-
stabilizer control-systems (CONFIG 1 aircraft)
• Connecting piece (6232.0026 - all varian ts) in aircraft with mechanical horizontal-
stabilizer control-systems (CONFIG 2 aircraft).
(2) Cause
It is possible that slightly asymmetric installation and/or operational conditions resulting in 
strong stabilizer vibration can cause the initiation of cracks.

### Page 2

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 2 of 24
SERVICE BULLETIN
(3) Solution
NOTE: As an alternative to the inspections detailed in (a) and (b) you can replace the 
non-inspected items. Replacement instead of inspection satisfies the 
requirements of this Service Bulletin.
(a) Before the next flight:
Do a visual inspection for crack damage in the applicable stabilizer-trim attachment 
components, and the related parts and structure. The stabilizer-trim actuator and 
the fitting or connecting piece must be removed to do the inspection. No cracks are 
permitted. Replace all crack damaged components and structure before the next 
flight.
NOTE: If the fitting or connecting piece has been in service for not more than 100 
flight hours and not more than 100 landings at the issue date of this SB, 
the visual inspection before next flight is not necessary.
(b) Within 100 flight hours or 100 landings (whichever comes first):
(i) Do a visual inspection for crack da mage in the applicable stabilizer-trim 
attachment components, and the related parts and structure. No cracks are 
permitted. Replace all crack damaged components before the next flight.
(ii) Remove the surface finish and do a dye-penetrant inspection for crack 
damage in the applicable stabilizer-trim attachment components, and the 
related parts and structure. No cracks are permitted. Replace all crack 
damaged components before the next flight.
NOTE: As an alternative to the dye-penetrant inspection you can do an 
eddy current inspection, which does not require removal of the 
surface finish. A right-angled shaft surface-probe with minimal drop 
is required to inspect in the gap between the lugs of the 
components:
- CONFIG 1 aircraft - smallest gap is 12,7 mm (0.5 in.).
- CONFIG 2 aircraft - smallest gap is 6 mm (0.24 in.).
(c) Before installation on an aircraft or within 6 months (whichever comes first):
(i) Do the inspection, detailed in Para. (3)(b) above, of all PC-6 horizontal 
stabilizer assemblies held as spares. Replace all crack damaged 
components before installation on an aircraft.
(ii) Do the inspection, detailed in Para. (3 )(b) above, of all PC-6 stabilizer control-
system fittings, connecting pieces, bearing supports and bearing forks held 
as spares. Discard all crack damaged parts.

### Page 3

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 3 of 24
D. Description
This Service Bulletin gives the data and instructions to do inspections for crack damage in the 
applicable stabilizer-trim attachment components and to replace defective components (if 
necessary).
Revision 1 is issued to:
• Show the screw (16), washer (17) and nut (18) on Fig. 1 and include them in the parts lists 
and procedures
• Correct two cross-references on Page 10 and correct the SB reference in the title of Fig. 2.
If operators have replaced the bearing fork (Fig. 1, Item 12) in accordance with the initial issue of 
this Service Bulletin, they must make sure it is installed with two bolts and one screw.
E. Compliance
Mandatory.
The visual inspection is required before the next flight, if:
• The fitting (on CONFIG 1 aircra ft) P/N 116.40.06.112 or 116.40.06.033 has been in service 
for more than 100 flying hours or 100 landings at the issue date of this Service Bulletin
• The connecting piece (on CONFIG 2 aircraft) P/N 6232.0026 has been in service for more 
than 100 flying hours or 100 landings at the issue date of this Service Bulletin.
The non-destructive inspection is required within 100 flight hours or 100 landings (whichever 
comes first) after the issue date of this Service Bulletin.
Horizontal stabilizer assemblies, stabilizer control-system fittings, connecting pieces, bearing 
supports and bearing forks held as spares are to be inspected before installation on an aircraft or 
within 6 months (whichever comes first) after the issue date of this Service Bulletin.
F. Approval
The technical content of this Service Bulletin is approved under the authority of DOA No. EASA. 
21J. 357.
PILATUS advises Operators/Owners to check with their designated Airworthiness Authorities for 
any changes, local regulations or sanctions that may affect the embodiment of this Service 
Bulletin.
G. Copyright and Legal Statements
© Pilatus Aircraft Ltd. This document contains proprietary information that is protected by 
copyright. All rights are reserved. No part of this document may be copied, reproduced or 
translated to other languages without the prior written consent of Pilatus Aircraft Ltd.
In connection with the use of this document, Pilatus does not provide any express or implied 
warranties and expressly disclaims any warranty of merchantability or fitness for a particular 
purpose. This document contains trade secrets, confidential and/or proprietary information of 
Pilatus and technical data subject to export control laws and regulations, including the U.S. 
Export Administration Regulations (EAR). Disclosure or distribution of this document contrary to 
the EAR, and other laws and regulations, is strictly forbidden. The above restrictions may apply 
to data on all pages of this document.

### Page 4

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 4 of 24
SERVICE BULLETIN
H. Manpower
NOTE: Man-hours figures do not include the time required to cure sealants and adhesives.
I. Weight and Balance
(1) Weight Change
None.
(2) Moment Change
None.
J. Electrical Load Data
Not changed.
K. Software
Not changed.
L. References
PC-6 aircraft except B2-H2/B2-H4:
• Airworthiness Limitations (AL) Doc. 02334: Appendix E and J.
• Repair and Overhaul Manual (ROM): Chapter 2 and 12.
PC-6 aircraft B2-H2/B2-H4:
• Aircraft Maintenance Manual (AMM) Doc. 01975: 27-45-11, 55-11-11.
• Structural Repair Manual (SRM): 51-00-03. 51-00-05, 51-00-06, 51-00-09.
Total (Inspection) Total (Replacements)
CONFIG 1 CONFIG 2 CONFIG 1 CONFIG 2
Preparation 1.0 1.0 - -
Removal 0.5 0.5 - -
Inspection A - Visual 0.5 0.5 - -
Inspection B - NDI 0.5 0.5 - -
Installation/Replacement of Fitting/
Connecting Piece
1.5 1.5 - -
Replacement of Bearing Fork/Bearing 
Supports
-- 4 . 0 6 . 0
Close up 0.5 0.5 - -
TOTAL MAN-HOURS 4.5 4.5 4.0 6.0

### Page 5

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 5 of 24
M. Publications Affected
None.
N. Interchangeability of Parts
Not applicable.

### Page 6

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 6 of 24
SERVICE BULLETIN
2. Material Information
A. Material - Pric e and Availability
No Modification Kit is required for this Service Bulletin.
Operators who require further information and/or Service Bulletin material should contact their 
Authorized Pilatus Service Center, or:.
Operators are requested to advise Pilatus Aircraft Ltd, of the Manufacturer’s Serial Number 
(MSN) and the flying hours and landings of aircraft which are affected by this Service Bulletin.
B. Material Necessary for Each Aircraft
NOTE: Part numbers given in this Service Bulletin are correct at the time of approval. Pilatus 
Aircraft Ltd. reserves the right to change the part numbers as necessary. Part numbers 
of items delivered are correct when dispatched. This could lead to differences between 
those part numbers quoted in this Service Bulletin and the delivered parts, if parts are 
superseded. Operators are requested to check the IPC for delivered parts which differ 
from those listed in the Service Bulletin Materials List.
(1) Material to be Purchased
Operators must order the following parts as necessary for replacement: 
PILATUS AIRCRAFT LTD
CUSTOMER SUPPORT MANAGER
CH-6371 STANS
SWITZERLAND
General Aviation:
Tel: + 41 41 619 3333
Fax: + 41 41 619 7311
eMail: SupportPC12@pilatus-aircraft.com
New Part No. Description Old Part No. Qty Disp. 
Code
Fig Item
112.35.06.197
6201.0134
FR12a Assembly 112.35.06.197
6201.0134
1R 1N / A
116.40.06.033 Fitting (CONFIG 1) 116.40.06.033 1 R 1 6
116.40.06.034 Bearing Fork 
(CONFIG 1)
116.40.06.034 1 R 1 12
116.40.06.112 Fitting - Post SB 147
(CONFIG 1)
116.40.06.112 1 R 1 N/A
6232.0026.01 Connecting Piece
(CONFIG 2)
6232.0026.01 1 R 1 9
6304.0023.01 Bearing Support (Left) 
(CONFIG 2)
6304.0023.01 1 R 1 3
6304.0023.02 Bearing Support (Right) 
(CONFIG 2)
6304.0023.02 1 R 1 2
932.35.14.105 Bolt (NAS6604-5) 
(CONFIG 2)
932.35.14.105 1 D 1 8
Disposition Codes: D - Discard / N - New / R - Return to Pilatus

### Page 7

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 7 of 24
(2) Operator Supplied Materials (Ref. AMM Do c. 01975, 20-31-00 or AL Doc. 02334, 
Appendix E) 
C. Material Necessary for Each Spare
(1) Material to be Purchased
Operators must order the following parts as necessary for replacement:
932.35.14.109 Bolt (NAS6604-9) 
(CONFIG 2)
932.35.14.109 1 D 1 8
6201.0134.11 Washer (CONFI G 2) 6201.0134.11 7 D 1 10
938.07.68.305 Nut (MS21046-4E) 
(CONFIG 2)
938.07.68.305 2 D 1 11
931.54.41.720 Screw, Pan Head
(NFL22271BC030020L)
(CONFIG 2)
931.54.41.209 1 D 1 16
938.07.31.103 Nut (3PA108)
(CONFIG 2)
938.07.34.100 1 D 1 18
938.71.51.103 Washer 
(NFL23111CA030)
(CONFIG 2)
938.78.13.103 1 D 1 17
Material No. Description Qty Remarks
P01-008 Solvent (White Spirit) A/R Or approved alternative
P02-020 Scotch-Brite A/R
P02-031 Absorbent Paper A/R
P04-039 Corrosion Preventative A/R CA1000
P07-001 CCC Solution A/R
P07-007 Epoxy Primer A/R
N/A Permanent Marker Pen 1 Edding Aerospace Marker 
8404 or equivalent
New Part No. Description Old Part No. Qty Disp. 
Code
Fig Item
116.40.06.034 Bearing Fork
(CONFIG 1)
116.40.06.034 1 R 1 12
116.40.06.033 Fitting (C ONFIG 1) 116.40.06.033 1 R 1 6
Disposition Codes: D - Discard / R - Return to Pilatus 
New Part No. Description Old Part No. Qty Disp. 
Code
Fig Item
Disposition Codes: D - Discard / N - New / R - Return to Pilatus

### Page 8

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 8 of 24
SERVICE BULLETIN
D. Re-identified Parts
Not applicable.
E. Tooling - Cost and Availability
Not applicable.
116.40.06.112 Fitting - Post SB 147
(CONFIG 1)
116.40.06.112 1 R 1 N/A
6304.0023.01 Bearing Support (Left) 
(CONFIG 2)
6304.0023.01 1 R 1 3
6304.0023.02 Bearing Support (Right) 
(CONFIG 2)
6304.0023.02 1 R 1 2
6232.0026.01 Connecting Piece
(CONFIG 2)
6232.0026.01 1 R 1 9
931.54.41.720 Screw, Pan Head
(NFL22271BC030020L)
(CONFIG 2)
931.54.41.209 1 D 1 16
938.07.31.103 Nut (3PA108)
(CONFIG 2)
938.07.34.100 1 D 1 18
938.71.51.103 Washer 
(NFL23111CA030)
(CONFIG 2)
938.78.13.103 1 D 1 17
New Part No. Description Old Part No. Qty Disp. 
Code
Fig Item
Disposition Codes: D - Discard / R - Return to Pilatus

### Page 9

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 9 of 24
3. Accomplishment Inst ructions - Aircraft
NOTE: AMM references given are applicable for holders of AMM Doc. 01975.
A. Preparation
(1) Remove the access panel FL2.
(2) CONFIG 1 Aircraft: 
(a) Remove the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 1), Page 
Block 401).
(3) CONFIG 2 Aircraft:
(a) Remove the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 2), Page 
Block 401). During this procedure use clamps (or equivalent) to make sure the 
cables stay in position on the spools of the mechanical actuator and operating 
mechanism.
(4) Use applicable supports to ho ld the horizontal stabilizer in a position which gives access to 
bottom surface.
B. Removal (Ref. Fig. 1)
(1) CONFIG 1 Aircraft:
(a) Remove the nuts (7), washers (5), bolts (4).
(b) Remove the fitting (6) from FR12a.
(c) Record the part marking of the fitting (6) on the Report Form supplied with this 
Service Bulletin.
(d) Discard the fitting if it has incomplete or missing part marking, unless you can 
confirm the service history of the fitting from its documentation.
(2) CONFIG 2 Aircraft:
(a) Remove the nuts (11), washers (10), bolts (8) and disassemble the connecting 
piece (9) from FR12a.
(b) Record the part marking of the connectin g piece (9) on the Report Form supplied 
with this Service Bulletin.
(c) Discard the connecting piece if it has in complete or missing part marking, unless 
you can confirm the service history of the connecting piece from its documentation.

### Page 10

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 10 of 24
SERVICE BULLETIN
C. Inspections (Ref. Fig. 1)
(1) Inspection A - Visual Inspection - Before the next flight:
(a) Remove loose paint if necessary, then us e absorbent paper (Material No. P02-031) 
and the solvent (Material No. P01-008) to clean:
• All surfaces of the fitting (6) or connecting piece (9)
• The surfaces of the bearing fork (12) or bearing supports (2) and (3) to which 
you have access
• The location on the surface of FR12a w here the fitting (6) or connecting piece 
(9) was installed.
(b) Use a 10x magnifier and bright light to visually examine the following parts for 
damage, cracks and signs of uneven wear. No damage, cracks or uneven wear is 
permitted:
• The fitting (6) or connecting piece (9)
• The bearing fork (12) or bearing supports (2) and (3) to which you have 
access.
If you find uneven wear, contact Pilatus Aircraft Ltd.
(c) Use a 10x magnifier and bright light to visually examine the surface of FR12a where 
the fitting (6) or connecting piece (9) was installed for damage, cracks and 
corrosion. No damage or cracks are permitted. Remove surface corrosion if found 
(Ref. ROM Chap 2 or SRM 51-00-05). Discard the part if less than 90% of the 
original material thickness remains after removal of the corrosion.
(d) Use internal vernier callipers (or equi valent) to do a check of the actuator 
attachment hole diameters in the fitting (6) (CONFIG 1) and connecting piece (9) 
(CONFIG 2). Hole diameters of more than 9,555 mm (0.3762 in.) in the fitting or 
16.036 mm (0.631 in.) in the connecting piece are not permitted. Replace defective 
components (Ref. Table 1 - Component Replacement Data).
(e) Use internal vernier calliper s (or equivalent) to do a check of the diameters of the 
attachment bolt holes in the fitting (6) (CONFIG 1) and FR12a (CONFIG 1). Hole 
diameters of more than 4,85 mm (0.191 in.) are not permitted. Replace the 
component if defective. If necessary, also replace FR12a, if the applicable holes for 
the fitting are out of limits (Ref. Table 1 - Component Replacement Data).
NOTE: If the Post SB 147 oversize bush (P/N 116.40.06.111) is installed, contact 
Pilatus Aircraft Ltd. for more information.
(f) Use internal vernier callipers (or equi valent instrument) to do a check of the 
diameters of the attachment bolt holes in the connecting piece (9) (CONFIG 2) and 
FR12a (CONFIG 2):
• If all of the hole diameters are 6,024 mm (0.23717 in.) or less, continue from 
Para D, Step (2)(b)
• If one or more of the holes are more than 6,024 mm (0.237 in.) but less than 
6,35 mm (0.25 in.), continue from Para D, Step (2)(c)

### Page 11

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 11 of 24
• If one or more holes are 6,35 mm (0.25 in.) or more, replace the connecting 
piece (9) and/or the FR12a (Ref. Table 1 - Component Replacement Data).
(2) Inspection B - Non-Destructive Inspection (NDI) - Within 100 flight hours or 100 
landings (whichever comes first):
(a) Do Inspection A - Visual Insp ection (Ref. Para. 3.C.(1)).
NOTE: The following step (b) is only necessary if you will do a dye-penetrant NDI. 
The eddy current NDI does not require the removal of surface treatment.
(b) Obey the manufacturers instructions and use the solvent (Material No. P01-008), 
Scotch-Brite (Material No P02-020) and/or non-metal scrapers to remove the layers 
of paint and protection from:
• All surfaces of the fitting (6) or connecting piece (9)
• The surfaces of the bearing fork (12) or bearing supports (2) and (3) to which 
you have access
• The location on the surface of FR12a where the fitting (6) or connecting piece 
(9) was installed.
CAUTION: ONLY PERSONNEL QUALIFIED AND CERTIFIED TO THE APPLICABLE 
LEVEL II (OR HIGHER) OF NATIONAL AEROSPACE STANDARD NAS 410, 
EUROPEAN STANDARD EN 4179 OR MIL-STD-410E, OR EQUIVALENT 
AEROSPACE STANDARD, ARE PERMITTED TO DO THE NDI.
(c) Do a dye-penetrant NDI, or the alte rnative eddy current NDI, as follows:
NOTE: Refer to Airworthiness Limitations Doc. 02334, Appendix J, or SRM 51-00-
09 as applicable for the related inspection procedures.
(i) Do the NDI for cracks in all surfaces of the:
• Fitting (6) or connecting piece (9). Make sure you do a thorough inspec-
tion of the critical areas shown on Figure 3
• Bearing fork (12) or bearing supports (2) and (3)
• Applicable area of FR12a. 
(ii) No crack damage is permitted. You must replace:
• Cracked components (Ref. Table 1 - Component Replacement Data)
• The two bearing supports (2) and (3) if only one is found cracked
• FR12a if cracks are found.

### Page 12

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 12 of 24
SERVICE BULLETIN
D. Installation/Replacement (Ref. Fig. 1)
(1) Install the fitting on CONFIG 1 aircraft:
NOTE: The following Steps (a) and (b) are not required when using a new fitting P/N 
116.40.06.112.
(a) Preparation of removed and inspected fitting:
(i) Obey the manufact urers instructions and apply layers of CCC solution 
(Material No. P07-001) as necessary to the applicable components and 
inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).
(ii) Obey the manufacturers instructions a nd apply layers of primer (Material No. 
P07-007) and paint as necessary to the applicable components and 
inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).
(iii) Use a permanent marker pen to re-a pply the part markings as recorded 
during the removal procedure.
(b) Preparation of new fitting P/N 116.40.06.033:
(i) Use a suitable drill and reamer to increase the diameter of the three 
attachment holes to between 4,820 and 4,832 mm.
(ii) Obey the manufacturer s instructions and apply layers of CCC solution 
(Material No. P07-001) as necessary to the reamed holes (Ref. ROM Chap 
12 or SRM 51-00-06).
(c) Obey the manufacturers instructions a nd apply layers of corrosion preventative 
(Material No. P04-039) on the faying surfaces of FR12a and the fitting (6), nuts (7), 
washers (5) and bolts (4).
(d) Put the fitting (6) in position on FR12 a and install the bolts (4), washers (5) and 
nuts (7).
Component Part No. Replacement 
FR12a Assembly 112.35.06.197
6201.0134
Ref. ROM Chap 2 or SRM 51-00-03
Fitting (CONFIG 1) 116.40.06. 033 Ref. Para D, Pre-Drilled
Bearing Fork (CONFIG 1) 116.40.06.034 Ref. Para D
Fitting (CONFIG 1) 116.40.06.112 Ref. Para D, Final Diameter
Connecting Piece
(CONFIG 2)
6232.0026.01 Ref. Pa ra D, Pre-Drilled
Bearing Support (Left)
(CONFIG 2)
6304.0023.01 Ref. ROM C hap 2 or SRM 51-00-03
Bearing Support (Right)
(CONFIG 2)
6304.0023.02 Ref. ROM C hap 2 or SRM 51-00-03
Table 1 - Component Replacement Data

### Page 13

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 13 of 24
(e) Obey the manufacturers instructions and use the solvent (Material No. P01-008) to 
remove unwanted corrosion preventative.
(2) Install the connecting piece on CONFIG 2 aircraft:
NOTE: The following Step (a) is required when using a new connecting piece P/N 
6232.0026.01.
(a) Preparation of a new connecting piece P/N 6232.0026.01:
(i) Use a suitable drill and reamer to incr ease the diameter of the two attachment 
holes to between 6,000 and 6,012 mm.
(ii) Obey the manufacturers instructions  and apply layers of CCC solution 
(Material No. P07-001) as necessary to the reamed holes (Ref. ROM Chap 
12 or SRM 51-00-06).
(b) Do the subsequent steps if all of the hole diameters are 6,024 mm (0.23717 in.) or 
less:
NOTE: The following Steps (i) thru (iii) are required only when using the removed 
and inspected connecting piece.
(i) Obey the manufacturers instructions  and apply layers of CCC solution 
(Material No. P07-001) as necessary to the applicable components and 
inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).
(ii) Obey the manufacturers instructions and  apply layers of primer (Material No. 
P07-007) and paint as necessary to the applicable components and 
inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).
(iii) Use a permanent marker pen to re-apply the part markings as recorded 
during the removal procedure.
(iv) Obey the manufacturers instructio ns and apply layers of corrosion 
preventative (Material No. P04-039) on the faying surfaces of FR12a and the 
connecting piece (9), bolts (8), washers (10) and nuts (11).
(v) Put the connecting piece (9) in posi tion on FR12a and install the bolts (8), 
washers (10) and nuts (11).
(vi) Obey the manufacturers instructions and use the solvent (Material No. P01-
008) to remove unwanted corrosion preventative.
(c) Do the subsequent steps if one or more of the holes are more than 6,024 mm (0.237 
in.) but less than 6,35 mm (0.25 in.).
(i) Use a 6,35 mm (0.25 in.) (H7) reamer  to increase the diameters of the bolt 
holes. Make sure there are no sharp edges.
(ii) Obey the manufacturers instructions  and apply layers of CCC solution 
(Material No. P07-001) as necessary to the applicable components and 
inspection areas and the surfaces of the bolt holes (Ref. ROM Chap 12 or 
SRM 51-00-06).

### Page 14

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 14 of 24
SERVICE BULLETIN
(iii) Obey the manu facturers instructions and apply layers of primer (Material No. 
P07-007) and paint as necessary to the applicable components and 
inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).
(iv) Use a permanent marker pen to re-apply the part markings as recorded 
during the removal procedure.
(v) Obey the manufacturers instructions and apply layers of corrosion 
preventative (Material No. P04-039) on the faying surfaces of FR12a and the 
connecting piece (9), bolts (8) (NAS6604-5 and -9), washers (10) and nuts 
(11) (MS21046-4E).
(vi) Put the connecting piece (9) in position on FR12a and install the longer bolt 
(8) (NAS6604-9) in the top hole and the shorter bolt (8) (NAS6604-5) in the 
lower hole. For each bolt (8) install one washer (10) under the head of the bolt 
and one washer (10) under the nut (11).
(vii) Obey the manufacturers instructions and use the solvent (Material No. P01-
008) to remove unwanted corrosion preventative.
(3) Replace the bearing fork or bearing supports if necessary (Ref. Fig. 1).
(a) Remove the horizontal  stabilizer (Ref. AMM 55-11-11, Page Block 401).
(b) On CONFIG 1 aircraft, remove the bearing fork (12):
(i) Use a suitable drill to remove the rivets  that attach the access panel (1) to the 
bottom skin of the horizontal stabilizer. (Ref. ROM Chap 2 or SRM 51-00-03).
NOTE: Some horizontal stabilizers have two access panels (1).
(ii) Remove the nuts (15) and (18), washers (14) and (17), the bolts (13) and the 
screw (16) then remove and discard the bearing fork (12).
(iii) Obey the manufacturer s instructions and apply layers of CCC solution 
(Material No. P07-001) as necessary in the rivet holes and on all bare metal 
surfaces.
(c) Preparation of a new bearing fork (12):
(i) Use a suitable drill and reamer to matc h drill the third hole in the bearing fork 
(12) to the existing 3,2 mm hole in the stringer. Use the removed bearing fork 
as a template.
(ii) Obey the manufacturer s instructions and apply layers of CCC solution 
(Material No. P07-001) as necessary to the reamed hole (Ref. ROM Chap 12 
or SRM 51-00-06).
(d) Install the new bearing fork (12).
(i) Obey the manufacturers instructions and apply layers of corrosion 
preventative (Material No. P07-039) on the faying surfaces of the bearing fork 
(12) and the adjacent structure. Also do this on the applicable surfaces of the 
nuts (15) and (18), washers (14) and (17), the bolts (13) and the screw (16).

### Page 15

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 15 of 24
(ii) Put the bearing fork (12) in position and install the bolts (13), the screw (16), 
the washers (14) and (17) and the nuts (15) and (18).
(iii) Obey the manufacturers instructions and use the solvent (Material No. P01-
008) to remove unwanted corrosion preventative.
(e) On CONFIG 2 aircraft, replace the bearing supports (2) and (3) (Ref. ROM Chap 2 
or SRM 51-00-03).
(f) Obey the manufacturers instructions and apply layers of CCC solution (Material No. 
P07-001) on the faying surfaces of the access panel (1) and adjacent skin.
(g) Put the access panel (1) in position and install rivets (CR3223-4-2) (Ref. ROM Chap 
2 or SRM 51-00-03).
(h) Install the horizontal stabilizer (R ef. AMM 55-11-11, Page Block 401).
E. Close up
(1) CONFIG 1 Aircraft: 
(a) Install the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 1), Page 
Block 401).
(2) CONFIG 2 Aircraft: 
(a) Install the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 2), Page 
Block 401).
(3) Remove all tools and materials. Ma ke sure the work areas are clean. 
(4) Install access panel FL2.
F. Reporting Action
(1) Send a report to Pilatus Aircraft Ltd. of t he inspection (including nil findings). Use the 
report form provided in this Service Bulletin.
(2) Return replaced parts to:
Pilatus Aircraft Ltd.
Customer Support General Aviation
Department GC
Ennetburgerstrasse 101
6370 Stans
Tel: +41 41 619 3333
G. Documentation
Make an entry in the Aircraft Logbook that Inspection A and/or B of this Service Bulletin is 
incorporated.

### Page 16

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 16 of 24
SERVICE BULLETIN
4. Accomplishment Instructions - Spares
NOTE: AMM references given are applicable for holders of AMM Doc. 01975.
A. Horizontal Stabilizer Assembly (Ref. Fig. 1)
It is not necessary to do this procedure if the horizontal stabilizer assembly held as spare has 
zero flying hours.
CAUTION: ONLY PERSONNEL QUALIFIED AND CERTIFIED TO THE APPLICABLE LEVEL 
II (OR HIGHER) OF NATIONAL AEROSPACE STANDARD NAS 410, EUROPEAN 
STANDARD EN 4179 OR MIL-STD-410E, OR EQUIVALENT AEROSPACE 
STANDARD, ARE PERMITTED TO DO THE NDI.
(1) Inspection
(a) Do a dye-penetrant inspection, or the alternative eddy current inspection, as 
follows:
NOTE: The dye-penetrant inspection requires the removal and re-application of 
surface finish and part markings. Keep a record of the part markings and 
re-apply using a permanent marker pen. Refer to Airworthiness 
Limitations Doc. 02334 (Appendix J) or SRM 51-00-09 for the related 
inspection procedures.
(i) Do inspections for cracks in the bearing fork (12) or bearing supports (2) and 
(3).
(ii) No crack damage is permitted. Replace defective components (Ref. Para. 
4.A.(2). You must replace the two bearing supports (2) and (3) if only one is 
found cracked.
(2) Replacement
(a) CONFIG 1 Horizontal  Stabilizer Assemblies:
(i) Use a suitable drill to remove the rivets  that attach the access panel (1) to the 
bottom skin of the horizontal stabilizer. (Ref. ROM Chap 2 or SRM 51-00-03).
NOTE: Some horizontal stabilizers have two access panels (1).
(ii) Remove the nuts (15) and (18), washers (14) and (17), the bolts (13) and the 
screw (16) then remove and discard the bearing fork (12).
(iii) Prepare the new bearing fork  (12) (Ref. Para. 3.D.(3)(c)).
(iv) Obey the manufacturer s instructions and apply layers of CCC solution 
(Material No. P07-001) as necessary in the rivet holes and on all bare metal 
surfaces.
(v) Obey the manufacturers instructions and apply layers of corrosion 
preventative (Material No. P04-039) on the faying surfaces of the new 
bearing fork (12) and the adjacent structure. Also do this on the applicable 
surfaces of the nuts (15) and (18), washers (14) and (17), the bolts (13) and 
the screw (16).

### Page 17

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 17 of 24
(vi) Put the bearing fork (12) in position and install the bolts (13), the screw (16), 
the washers (14) and (17) and the nuts (15) and (18).
(vii) Obey the manufacturers instructions and use the solvent (Item No. P01-008 
or approved alternative) to remove unwanted corrosion preventative.
(viii) Obey the manufacturers instructio ns and apply layers of corrosion 
preventative (Material No. P04-039) as necessary) on the faying surfaces of 
the access panel (1) and adjacent skin.
(ix) Put the access panel (1) in position and install rivets (CR3223-4-2) (Ref. 
ROM Chap 2 or SRM 51-00-03).
(b) CONFIG 2 Horizontal Stabilizer Assemblies: 
(i) If cracks are found replace the bearin g supports (2) and (3) (Ref. ROM Chap 
2 or SRM 51-00-03). You must replace the two bearing supports if only one 
was found defective.
B. Inspection - Stabilizer Control-System Fi ttings, Connecting Pieces, Bearing Supports and 
Bearing Forks 
It is not necessary to do this procedure if the stabilizer control-system fittings, connecting pieces, 
bearing supports and bearing forks held as spare have zero flying hours.
CAUTION: ONLY PERSONNEL QUALIFIED AND CERTIFIED TO THE APPLICABLE LEVEL 
II (OR HIGHER) OF NATIONAL AEROSPACE STANDARD NAS 410, EUROPEAN 
STANDARD EN 4179 OR MIL-STD-410E, OR EQUIVALENT AEROSPACE 
STANDARD, ARE PERMITTED TO DO THE NDI.
(1) Do a dye-penetrant inspection, or the alte rnative eddy current inspection, as follows:
NOTE: The dye-penetrant inspection requires the removal and re-application of surface 
finish and part markings. Keep a record of the part markings and re-apply using 
a permanent marker pen. Refer to Airworthiness Limitations Doc. 02334 
(Appendix J) or SRM 51-00-09 for the related inspection procedures.
(a) Do inspections for cracks in  all stabilizer control-system fittings, connecting pieces, 
bearing supports and bearing forks.
(b) No crack damage is permitted. Discard all defective parts.
C. Reporting Action
(1) Send a report to Pilatus Aircraft Ltd. of t he inspection (including nil findings). Use the 
report form provided in this Service Bulletin.
(2) Return replaced parts to:
Pilatus Aircraft Ltd.
Customer Support General Aviation
Department GC
Ennetburgerstrasse 101
6370 Stans
Tel: +41 41 619 3333

### Page 18

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 18 of 24
SERVICE BULLETIN
D. Documentation
Make an entry in the spare parts inventory list that this Service Bulletin is incorporated.

### Page 19

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 19 of 24
 Stabilizer-trim Attachment Components - Inspection and Replacement
(Riveted Fairchild Type was Removed by SB 53-001 Rev. 1)
Figure 1
B
A
16
C
C
B
B
CONFIG 1
1
CONFIG 2
A
A
1
1 1
2 3
CONFIG 1
4
5
6
5
7
CONFIG 2
8
9
10
11
11
10
12
1415
FR12A
FR12A
109
FAIRCHILD TYPE
RIVET
NOTE:
OUT OF SERVICE
13
14
18 17

### Page 20

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 20 of 24
SERVICE BULLETIN
Difference Between Fittings 116.40.06.033
(Fitting Without Index was Removed by SB 53-001 Rev. 1)
Figure 2
1479
WITH INDEX AFTER
PART NUMBER
WITHOUT INDEX AFTER
PART NUMBER
NOTE: OUT OF SERVICE

### Page 21

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 21 of 24
Critical Inspection Areas
Figure 3
SB2886
CRITICAL AREAS
CRITICAL AREAS

### Page 22

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 22 of 24
SERVICE BULLETIN
INTENTIONALLY BLANK

### Page 23

SERVICE BULLETIN
Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 23 of 24
Report Form
Compliance Level                  Inspection A - Visual Inspection
                 Inspection B - Dye Penetrant or Eddy Current NDI
Aircraft Data Manufacturer's Serial Number Aircraft Total Flying Hours Aircraft Total Landings
SB 53-001 Initial Issue Date of Incorporation Aircraft Total Flying Hours Aircraft Total Landings
SB 53-001 Revision 1
AMM  Inspection Date of Last Inspection Aircraft Total Flying Hours Aircraft Total Landings
(Ref. AMM 53-30-00 or AL Doc. 02334 APP. A)
Inspection Method             Dye Penetrant             Eddy Current (AMOC)
Service Data of Installed Parts
Mechanical Trim System Date of Installation Aircraft Total Flying Hours Aircraft Total Landings
 FR12a Assembly P/N 6201.0134
Connecting Piece P/N 6232.0026.01
Bearing Support P/N 6304.0023.01/02 or
Bearing Fork P/N 116.40.06.034
Electro-Mechanical Trim System Date of Installation Aircraft Total Flying Hours Aircraft Total Landings
FR12a Assembly P/N 112.35.06.197
Fitting P/N 116.40.06.112 or
P/N 116.40.06.033
Bearing Fork P/N 116.40.06.034
Inspection Result of Installed Parts
Mechanical Trim System
FR12a Assembly P/N 6201.0134
Connecting Piece P/N 6232.0026.01
Bearing Support P/N 6304.0023.01/02 or
Bearing Fork P/N 116.40.06.034
Electro-Mechanical Trim System
FR12a Assembly P/N 112.35.06.197
Fitting P/N 116.40.06.112 or
P/N 116.40.06.033
Bearing Fork P/N 116.40.06.034
Other Observations
Date Returm Completed Form To:
Inspector Name Pilatus Aircraft Ltd.,
Inspector Level Customer Support General Aviation,
Inspector Signature CH-6371 Stans, Switzerland.  FAX +41 41 619 73 11
Email:  supportpc12@pilatus-aircraft.com
Uneven  Wear 
 YES / NO              
Repair 
YES / NO 
Cracks 
YES / NO                   
Corrosion 
YES / NO             
Replacement 
YES / NO

### Page 24

Service Bulletin No: 53-003  Date: Oct 04/16
Rev. No.   1 Date: Oct 13/16 Page 24 of 24
SERVICE BULLETIN
INTENTIONALLY BLANK

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
