# Pilatus Service Bulletin 27-010: No revision named

- Rights: © Pilatus Aircraft Ltd. Filed by the FAA in regulations.gov docket FAA-2025-0208, the docket of AD 2025-10-10. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Pilatus Service Bulletin 27-010](https://openairdocs.org/service-documents/pilatus/sb-27-010.md)
- Title as filed: Pilatus PC-24 - Service Bulletin 27-010 - Initial Issue
- Pages: 18
- PDF: https://openairdocs.org/files/sha256/b5/9f/b59fc50daaa6ef62f055eb463c299c3d4a39ab73d77a79b41317f88c2deffe23
- Page: https://openairdocs.org/service-documents/pilatus/sb-27-010/file/b59fc50daaa6

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin No: 27-010 Ref No: 233
Modification No: EC-23-0567 ATA Chapter: 27
SERVICE BULLETIN
Pilatus Aircraft Ltd, Pilatusstrasse 1, 6371 Stans, Switzerland
Service Bulletin No: 27-010 Date: Jul 04/24
Rev. No.   Date: Page 1 of 18
FLIGHT CONTROLS - YAW CONTROL
IMPROVEMENTS TO THE RUDDER-TRIM SYSTEM
1. Planning information
A. Effectivity
PC-24 aircraft MSN 101 thru MSN 530 (Pre or Post SB 27-009) that have short rudder trim 
control rods P/N 527.20.24.464 installed. 
This modification will be incorporated on MSN 531 and subsequent during production.
B. Concurrent requirements
None.
C. Reason
This Service Bulletin introduces a modification of the short rudder-trim control rods and removes 
the need to do the repetitive replacement of these control rods as given in PC-24 SB 27-009.
(1) Problem
Pilatus has become aware that the titanium threaded bolts at the forward end of the short 
rudder trim tab actuating rods may be subject to oscillating loads due to aerodynamic 
forces acting on the trim tab.This condition, if not detected and corrected, could lead to bolt 
failure, possibly resulting in loss of the rudder control.
(2) Solution
Modification of the short rudder trim control rods, and a change of material for the 
threaded rod ends to improve fatigue tolerance.
D. Description
This Service Bulletin gives the data and instructions necessary to modify the short rudder trim 
control rods.
E. Compliance
Mandatory.
At the next opportunity, but no later than:
The AD 2023-0219-E is not applicable after embodiment of PIL Service Bulletin No: 27-010, 
initial issue, or later amendment, as per EASA Major change approval 10084861 dated 03 July 
2024
• The first 300 FH of the aircraft
OR
• 300 FH from the last accomplishment of Service Bulletin SB 27-009.

### Page 2

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 2 of 18
SERVICE BULLETIN
F. Approval
The technical content of this document is approved under the authority of the DOA ref. 
EASA.21J.357.
Pilatus advises Operators/Owners to check with their designated Airworthiness Authority for any 
changes, local regulations or sanctions that may affect the embodiment of this Service Bulletin.
G. Copyright and legal statement
© Pilatus Aircraft Ltd. This document contains proprietary information that is protected by 
copyright. All rights are reserved. No part of this document may be copied, reproduced or 
translated to other languages without the prior written consent of Pilatus Aircraft Ltd.
In connection with the use of this document, Pilatus does not provide any express or implied 
warranties and expressly disclaims any warranty of merchantability or fitness for a particular 
purpose. This document contains trade secrets, confidential and/or proprietary information of 
Pilatus and technical data subject to export control laws and regulations, including the U.S. 
Export Administration Regulations (EAR). Disclosure or distribution of this document contrary to 
the EAR, and other laws and regulations, is strictly forbidden. The above restrictions may apply 
to data on all pages of this document.
H. Manpower
NOTE: The man-hours do not include the time necessary to cure sealants, paints and 
adhesives.
I. Weight and balance
(1) Weight change:
+ 0.177 lb (+ 0,080 Kg).
(2) Moment change:
+ 103.476 lb*in (+ 1,192 Kg*m).
J. Electrical load change data
Not changed.
K. Software
Not changed.
Description Man-Hours
Preparation 0.5
Modification 6.5
Requirements after job completion 0.5
TOTAL MAN-HOURS 7.5

### Page 3

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 3 of 18
L. References
Aircraft Maintenance Manual (AMM):
Tools and Equipment Manual (TEM):
M. Publications affected
Airplane Flight Manual (AFM).
Aircraft Maintenance Manual (AMM).
Illustrated Parts Data (IPD).
N. Interchangeability of parts
One-way interchangeable.
Pre-Service Bulletin parts must not be installed on post-Service Bulletin aircraft.
PC24-A-A00-50-0000-00A-070A-A PC24-A-E20-10-0003-00A-913A-A
PC24-A-E20-10-0003-01A-913A-A PC24-A-E20-10-0004-00A-913A-A
PC24-A-E20-20-0001-00A-040A-A PC24-A-E20-40-0000-00A-913A-A
PC24-A-E24-00-0000-00A-913A-A PC24-A-E27-20-0000-00A-340A-A
PC24-A-E27-20-0005-00A-320A-A PC24-A-E27-20-0006-00A-520A-A 
PC24-A-E27-20-0006-00A-720A-A 
PC24-A-A00-00-0000-00A-060A-A.

### Page 4

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 4 of 18
SERVICE BULLETIN
2. Material information
Operators that require additional information and/or Service Bulletin material can 
contact their authorized Pilatus Service Center, or Pilatus Customer Support on 
https://www.pilatus-aircraft.com  contact us.
NOTE: Part numbers given in this Service Bulletin are correct at the time of 
approval. Pilatus Aircraft Ltd reserves the right to change the part numbers 
as necessary. Part numbers of items delivered are correct when 
dispatched. This could lead to differences between those part numbers 
quoted in this Service Bulletin and the delivered parts, if parts are 
superseded. Operators are requested to check the Illustrated Parts Data 
(IPD) for delivered parts that differ from those listed in the Service Bulletin 
Materials List.
Operators are requested to advise Pilatus Aircraft Ltd of the Manufacturer’s Serial 
Number (MSN), the flying hours and landings of aircraft that are allocated for this 
Service Bulletin.
A. Material - Price and availability
B. Warranty
Credit for parts and labour will be issued for all affected aircraft on approval of a warranty claim, 
provided the work is accomplished by an authorized Service Center within the compliance time 
given in Section 1.E on Page 1 of this Service Bulletin.
C. Material necessary for each aircraft
(1) Material to or der from Pilatus
Modification kit number Price Availability
500.50.24.167 Contact as a bove Approximately 2 weeks

### Page 5

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 5 of 18
Modification Kit P/N 500.50.24.167
NOTE: When ordering parts, Service Centers are requested to indicate the required by date on 
the purchase order.
NOTE: Please indicate the Aircraft MSN(s) on the purchase order for which the parts are 
ordered.
NOTE: The new part number has a lower running order than the old part number.
(2) Locally supplied materials
To identify the materials used in this procedure, look in the Consumable materials list. Refer to 
AMM PC24-A-A00-50-0000-00A-070A-A.
NOTE: Also refer to any referenced AMM procedures, if applicable.
D. Material necessary for each spare
Not applicable.
New part No. Description Old part No. Qty Disp.
code
Fig Item
527.20.24.040
(See NOTE below)
Bolt, Threaded -
527.20.24.489
2
2
N
D
11 5
10
527.20.24.039 
(See NOTE below)
Tube, Rod -
527.20.24.488
2
2
N
D
11 4
9
527.20.24.042 Nut, Hex, RH, CRES, 
PASS, 6.4*7.0
-
938.02.27.202
2
2
N
D
11 6
11
Disposition Codes: D - Discard / N - New / R - Return to Pilatus / E - Exchange Part
Material No. Description Qty Remarks
P01-033 Wipes, presaturated
solvent
AR -
P02-007 Lockwire AR Diameter 0.025 in (0,6 mm)
P04-041 Grease AR -
P07-038 Topcoat, clear-gloss
polyurethane
AR -
P08-106 Sealant, interfay AR MC-780 C-1/3 / C-2 / C-4 / C-8 / C-12 / C-24 / 
C-48 / C-60

### Page 6

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 6 of 18
SERVICE BULLETIN
E. Re-identified parts
NOTE: The S/N of the old assembly is transferred to the new assembly.
New Part No. Descrip tion Old Part No.
P/N 527.20.24.069 Control Rod, Rudd er-Trim, Short P/N 527.20.24.464

### Page 7

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 7 of 18
F. Tools and equipment
To identify the tools and equipment (where a TEM Tool No. is given), look in the product support 
equipment, tools and software list. Refer to TEM PC24-A-A00-00-0000-00A-060A-A.
NOTE: Also refer to any referenced AMM procedures, if applicable.
Tools and equipment Recommended
Pilatus part
‘DO NOT CONNECT ELECTRICAL POWER’ sign Local supply
Flight control rigging tool kit
(TEM Tool No. T27-003)
P/N 513.27.24.171
Permanent marker pen Local supply
Tape Local supply
Tool kit, mechanic Local supply
Yaw/Roll/Pitch trim control box Local supply

### Page 8

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 8 of 18
SERVICE BULLETIN
3. Accomplishment instructions
WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ELECTRICAL SYSTEM OR A SYSTEM 
THAT USES ELECTRICAL POWER. MAKE SURE THAT IT IS SAFE BEFORE YOU 
APPLY ELECTRICAL POWER TO THE AIRCRAFT OR ENERGIZE THE AIRCRAFT 
ELECTRICAL SYSTEMS. ELECTRICAL POWER CAN CAUSE DEATH OR INJURY TO 
PERSONNEL AND/OR DAMAGE TO EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIALS. OBEY THE 
MANUFACTURER´S HEALTH AND SAFETY INSTRUCTIONS AND ALL THE 
APPLICABLE LOCAL INSTRUCTIONS. CONSUMABLE MATERIALS CAN BE 
DANGEROUS AND CAN CAUSE DEATH OR INJURY TO PERSONNEL AND/OR 
DAMAGE TO EQUIPMENT.
NOTE: Refer to the manufacturer’s instructions for the necessary time for consumable 
materials to cure/dry.
NOTE: For all torque related information necessary for this procedure, refer to AMM PC24-A-
E20-20-0001-00A-040A-A.
A. Preparation
(1) Obey the safe maintenance practices as necessary. Refer to AMM PC24-A-E20-10-0003-
00A-913A-A.
(2) Make sure that no other work is in progress on the aircraft.
(3) Make sure that the aircraft is in safe maintenance mode. Refer to AMM PC24-A-E20-10-
0003-01A-913A-A.
(4) De-energize the aircraft electrical system. Refer to AMM PC24-A-E24-00-0000-00A-913A-
A.
(5) Put a ‘ DO NOT CONNECT ELECTRICAL POWER’ sign on the:
• Overhead control panel
• External power connection.
B. Modification
(1) Do the rudder-trim actuator remove procedure to remove and keep the upper and lower 
short rudder-trim control rods (9). Refer to AMM PC24-A-E27-20-0006-00A-520A-A and 
Figure 1.
(2) Record the serial numbers and installation position of the upper and lower short rudder-
trim control rod assemblies.
(3) Measure and record the full length (Dimension X) of the upper and lower short rudder-trim 
control rods (9) that you kept. Refer to Figure 1, PRE-SB 27-010, Section A-A.

### Page 9

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 9 of 18
(4) Modify the upper and lower short rudder-trim control rods as follows. Refer to Figure 1:
NOTE: The procedure to modify the upper and lower short rudder-trim control rods is the 
same.
(a) Remove and keep the locking washer (12) and the tab washer (13) from the 
threaded bolt (10).
(b) Remove and discard the lock wire from the two lock nuts (2) and (6) and the two tab 
washers (4) and (8).
(c) Loosen the two lock nuts (2) and (6).
(d) Remove and keep the eye-end (1), the lock nut (2), the locking washer (3) and the 
tab washer (4) from the vernier sleeve (5).
(e) Remove and keep the vernier sleeve (5), th e lock nut (6), the locking washer (7) and 
the tab washer (8) from the short rudder-trim control rod (9).
(f) Discard the short rudder-trim control rod (9), together with the threaded bolt (10) 
and the lock nut (11).
(g) Use wipes, presaturated solvent (Material No. P01-033) to clean the items that 
follow (that you kept):
• Eye-end (1)
• Two lock nuts (2) and (6)
• Three locking washers (3), (7), and (12)
• Three tab washers (4), (8), and (13)
• Vernier sleeve (5).
(h) Let the solvent dry.
(i) Inspect the items that fo llow for damage, cracks, and corrosion. Refer to AMM 
PC24-A-E20-40-0000-00A-913A-A:
• Eye-end (1)
• Two lock nuts (2) and (6)
• Three locking washers (3), (7), and (12)
• Three tab washers (4), (8), and (13)
• Vernier sleeve (5).
(j) If you find damage, cracks, and corrosion, replace the items above as necessary.
(k) Apply a thick layer of interfay sealant (Ma terial No. P08-106) to the mating threads 
and mating surfaces of the new threaded bolt (P/N 527.20.24.040) (15) and the new 
short rudder-trim control rod (P/N 527.20.24.039) (14). Refer to Figure 1, POST-SB 
27-010.
(l) Install the threaded bolt (15) in the short rudder-trim control rod (14).

### Page 10

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 10 of 18
SERVICE BULLETIN
(m) Torque the threaded bolt (15) to between 66 and 75 lbf in (7.5 and 8.5 Nm) plus the 
run down torque.
(n) Make sure that excess sealant can be seen around the mating surfaces of the 
threaded bolt (15) and the short rudder-trim control rod (14).
(o) Use wipes, presaturated solvent (Material No. P01-033) to remove unwanted 
sealant.
(p) Let the sealant cure.
(q) Use lockwire (Material No. P02-007) to safety the threaded bolt (15) in the short 
rudder-trim control rod (14).
(r) Apply a thin layer of grease (Material No. P04-041) to the threads of the items that 
follow:
• Eye-end (1)
• Two lock nuts (2) and (6)
• Vernier sleeve (5).
(s) Loosely install the tab washer (4), the lo cking washer (3), the lock nut (2), and the 
eye-end (1) in the vernier sleeve (5).
(t) Measure dimension Y between the FWD end of the vernier sleeve (5) and the aft 
end of the eye-end (1). Refer to Figure 1, POST-SB 27-010, Section B-B.
(u) Adjust the eye-end (1) in the vernier sleev e (5) to make sure that dimension Y is 
3.22 in (81.7 mm).
(v) Tighten the lock nut (2) by hand.
(w) Loosely install the tab washer (8), the locking washer (7), the lock nut (6), and the 
vernier sleeve (5) in the short rudder-trim control rod (14).
(x) Turn the vernier sleeve (5) and the eye-end  (1) in the short rudder-trim control rod 
(14) to set the length of the short rudder-trim control rod (14) to the recorded value 
(Dimension X). Refer to Figure 1, POST-SB 27-010, Section B-B.
NOTE: Final adjustment of the rods will be done when the rudder-trim actuator is 
installed. Dimension X is set at this time to make the installation of the 
actuator easier.
(y) Tighten the lock nut (6) by hand.
(z) Make sure that the two tab washers (4) and (8) point to the right when looking in the 
direction of flight. This will make installation of the control rods easier.
(aa) Make sure that you can see the threads of the eye-end (1) in the witness hole of the 
vernier sleeve (5).
(ab) Make sure that you can see the threads  of the vernier sleeve (5) in the witness 
holes of the short rudder-trim control rod (14).

### Page 11

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 11 of 18
(ac) Apply a thin layer of grease (Material No. P04-041) to the threads of the new lock 
nut (P/N 527.20.24.042) (16).
(ad) Loosely install the new lock nut (16) the locking washer (12), and the tab washer 
(13) (that you kept) on the threaded bolt (15).
(ae) Do the above procedure again, Steps (4) (a) thru (4) (ad) for the other short rudder-
trim control rod (9).
(5) Re-identify the two new short rudder-trim control rod assemblies (14):
(a) Clean the areas where the new short rudder-trim control rod assemblies (14) will be 
re-identified with the new P/N and old S/N. Use wipes, presaturated solvent 
(Material No. P01-033).
(b) Let the solvent dry.
(c) Use a permanent marker pen and re-identify the new short rudder-trim control rod 
assemblies (14) with:
• New part number P/N 527.20.24.069
• The same serial number from the short rudder-trim control rod assemblies (9) 
that you recorded in step B.(2)
• SB 27-010 at the end of the serial number.
(d) Apply a layer of topcoat (Material No. P07- 038) to protect the re-identification areas.
(e) Let the topcoat dry.
(6) Prepare the rudder trim actuator and the short rudder-trim control rod assemblies for 
installation, as follows. Refer to Figure 2:
(a) Install the rudder-trim actuator (1) in the trim actuator adjusting-jig from the flight 
control rigging tool kit (TEM. No. T27-003).
(b) Make sure that the length of the two ra ms (4) are in the mid-stroke position. The 
mid-stroke position is when the dimension A is 5.76 ±0.02 in (146.4 ±0.5 mm). If 
necessary, adjust the length of the two rams (4) as follows:
1 Connect the Yaw/Roll/Pitch trim control box to the rudder-trim actuator (1).
2 Set the two rudder trim actuator-rams (4) to the mid-stroke position.
3 Disconnect the Yaw/Roll/Pitch trim control box from the rudder-trim actuator 
(1).
(c) Remove the rudder-trim actuator (1) from the trim actuator adjusting-jig.
(d) Connect the upper / lower short rudder-tri m control rods (2) and (3) to the two rams 
(4) of the rudder-trim actuator (1) as follows:
NOTE: The procedure to connect the upper/lower control rods to the upper/lower 
ram is the same.

### Page 12

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 12 of 18
SERVICE BULLETIN
1 Apply a thin layer of grease (Material No. P04-041) to the thread of the short 
rudder-trim control rod.
2 Put the short rudder trim control rod in position on the ram (4) of the rudder-
trim actuator (1).
• Upper rod (2) on upper ram (4)
• Lower rod (3) on lower ram (4).
3 Make sure that the tab washer (5) and the lock washer (6) are fully 
disengaged.
4 Make sure that the position of the lock nut (7) on the short rudder-trim control 
rod gives sufficient travel to adjust the push rod.
5 Turn the short rudder trim control rod to adjust the position of the rod in the 
ram (4).
6 Make sure that the dimension B is 0.54 ± 0.04 in (13.8 ± 1 mm).
7 Make sure that the detent (8) is in the horizontal position and the tab washer 
(9) points to the right, when you look in the direction of flight. Refer to view C.
8 Engage the tab washer (5) and the lock washer (6) on the ram (4).
9 Make sure that the tab washer (5) points to the right.
10 Tighten the lock nut (7) with your hand.
11 Make sure that the tab washer (5) and the lock washer (6) are correctly 
engaged.
12 Torque the lock nut (7) to between 66 and 75 in-lb (7.5 to 8.5 Nm).
13 Make sure that the dimension B is 0.54 ± 0.04 in (13.8 +/-1mm). Refer to 
Figure 2.
14 If the dimension B is not 0.54 ± 0.04 in (13.8 +/-1mm), do the steps that 
follow:
i Loosen the lock nut (7).
ii Do Step (d).3 thru Step (d).13 again.
15 This step is applicable to MSN 128-UP.
Use lockwire (Material No. P02-007) to safety the lock nut (7) to the lock tab 
washer (5).
16 Do the above procedure, steps (5) (d)1 thru (5) (d)16 again to connect the 
other short rudder-trim control rod to the other ram (4) of the rudder trim 
actuator (1).

### Page 13

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 13 of 18
(e) Aircraft MSN 101 thru MSN 127 do the steps that follow. Refer to Figure 2:
1 Record the position of the two lock nuts (7) on the upper and lower short 
rudder-trim control rods (2) and (3).
2 Loosen the two lock nuts (7) on the upper and lower short rudder-trim control 
rods (2) and (3) by one turn.
3 If necessary hold the two lock nuts (7) in position with tape.
4 Remove the upper and lower short rudder-trim control rods (2) and (3) from 
the rudder trim actuator (1).
(7) Do the rudder trim actuator install proc edure. Refer to AMM PC24-A-E27-20-0006-00A-
720A-A and Figure 1.
NOTE: It is not necessary to do the setup of the short rudder-trim control rods when you 
do the above referenced procedure. This was done in the previous step.

### Page 14

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 14 of 18
SERVICE BULLETIN
C. Test
(1) Remove the ‘ DO NOT CONNECT ELECTRICAL POWER’ sign from the:
• Overhead control panel
• External power connection.
(2) Connect a Ground Power Unit (GPU) to the aircraft and:
• Energize the aircraft electrical system
• Make sure that the GPU supplies power to the aircraft.
Refer to AMM PC24-A-E24-00-0000-00A-913A-A.
(3) Set the aircraft to safe maintenance mode. Refer to AMM PC24-A-E20-10-0003-01A-
913A-A.
(4) Make sure you have done the rudder trim operation test. Refer to PC24-A-E27-20-0005-
00A-320A-A.
(5) Make sure you have done the rudder control function test. Refer to PC24-A-E27-20-0000-
00A-340A-A.
D. Requirements after job completion
(1) De-energize the aircraft electrical system. Refer to AMM PC24-A-E24-00-0000-00A-913A-
A.
(2) Disconnect the GPU from the aircraft. Refer to AMM PC24-A-E24-00-0000-00A-913A-A.
(3) Remove all the equipment, tools and materials from the work area. Make sure that the 
work area is clean.
(4) Do the Closeup practices. Refer to AMM PC24-A-E20-10-0004-00A-913A-A.
E. Documentation
(1) Make an entry in the Aircraft Logbook to record the accomplishment of this Service 
Bulletin.
(2) Make sure that the Aircraft Logbook shows any new Pilatus Part Number(s) and/or Serial 
Number(s), as applicable.
(3) Make sure that all applicable Ai rcraft Documentation is updated.
(4) Inform CAMP of the incorporation of this Service Bulletin and any new Pilatus Part 
Number(s) and/or Serial Number(s), as applicable. Send the completed feedback sheet to: 
fax@campsystems.com

### Page 15

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 15 of 18
Modification of the rudder-trim short control rods
Figure 1 (Sheet 1 of 2)
SB 4805
SECTION
A-A
1
2
4 5
6
7
8
10
9
11
12
13
X
A
NOTE:
DISCARDED1
1
1
3
A
PRE SB 27-010
TYPICAL
1

### Page 16

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 16 of 18
SERVICE BULLETIN
Modification of the rudder-trim short control rods
Figure 1 (Sheet 2 of 2)
14
1
2
4 5
6
7
8
SECTION
B-B
X
3
16 12
13
15
SB 4806
B
B
POST SB 27-010
X
Y
NOTE:
NEW PARTS ( MOD KIT)2
2
2
2

### Page 17

SERVICE BULLETIN
Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 17 of 18
Rudder-trim actuator and short control rods - Setup
Figure 2 (Sheet 1 of 1)
B
BC
C
TYPICAL
C
A
A
TYPICAL
B
B
4567
A
9
2
1
3
SB 4808
8

### Page 18

Service Bulletin No: 27-010  Date: Jul 04/24
Rev. No.   Date: Page 18 of 18
SERVICE BULLETIN
Feedback Sheet for the Accomplishment of SB 27-010
The purpose of this feedback sheet is to provide CAMP
with the current information on each individual PC-24 aircraft.
Please complete the grey cells as appropriate using black ink and block letters.
Print out and send the completed feedback sheet to: fax@campsystems.com
SB Accomplishment Information
CAMP Feedback Sheet
Aircraft MSN Aircraft Registration Total Airframe Hours
Service Center Total Landings
We have embodied/accomplished this SB Fully Partially
The undersigned confirms the accomplishment of this Service Bulletin
Date of accomplishment Name Signature
Comments (procedure, kit quality, suggested improvements etc.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
