# Piper Mandatory Service Bulletin 1245: Revision A

- Rights: © Piper. Filed by the FAA in regulations.gov docket FAA-2012-0731; AD 2013-02-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Piper Mandatory Service Bulletin 1245](https://openairdocs.org/service-documents/piper/sb-1245.md)
- Title as filed: U.S. DOT/FAA - Service Information - 2
- Pages: 3
- PDF: https://openairdocs.org/files/sha256/74/0c/740c13407c3cf1512f3a3eda3cc3d110e9a2282260fe93a572f0e3ccdafdb964
- Page: https://openairdocs.org/service-documents/piper/sb-1245/file/740c13407c3c

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin (SB) supersedes SB 1245. Aircraft that have previously complied with SB 1245 are already in 
compliance with SB 1245A.
SUBJECT: STABILATOR COnTROL SySTEm InSPECTIOn
REASOn fOR REvISIOn: SB1245A clarifies cleaning and inspection instructions. 
mODELS AffECTED: SERIAL nUmBERS AffECTED:
PA-28 Series All
PA-28S Series All
PA-28R Series All
PA-28RT Series All
PA-32 Series All
PA-32S Series All
PA-32R Series All
PA-32RT Series All
PA-34 Series All
PA-44 Series All
COmPLIAnCE TImE: Upon reaching fifteen (15) calendar years time-in-service, initial inspection to 
coincide with the next regularly scheduled maintenance event.  
Thereafter, compliance to be accomplished on a recurring basis, at an interval 
not to exceed two thousand (2,000) operating hours or seven (7) calendar years 
time-in-service, whichever occurs first.
nOTE:   A logbook entry documenting the replacement of any flight control 
cable or turnbuckle body will relieve the inspection requirement for that 
component only, until such time as that component has been in service 
for 15 calendar years.
APPROvAL: The technical content of this Service Document has been shown to comply with 
the applicable Federal Aviation Regulations and is FAA approved.
 SERvICE      NO.    1245A
    BULLETIn
PIPER COnSIDERS
COmPLIAnCE mAnDATORy
Piper Aircraft, Inc.
2926 Piper Drive
Vero Beach, Florida, U.S.A.  32960
Date:   November 28, 2012     (S) (M)
ATA: 2730
(OVER)

### Page 2

SERvICE BULLETIn nO. 1245A PAGE 2 of 3
PURPOSE: Existing Instructions for Continued Airworthiness (i.e., the appropriate Piper 
Maintenance Manual and associated Service Publications) include an inspection 
of all flight control pulleys, cables, fittings and turnbuckles on a recurring basis. 
However, service history suggests that over time, the turnbuckles used in the 
stabilator flight control cable system may develop cracks or corrosion which may 
not be detected during these inspections.
This Service Bulletin provides specific instructions for the recurring inspection of 
the stabilator flight control system.
nOTE:  Refer to the applicable Piper Maintenance Manual, as well as Piper 
Service Letters SL 1069 and SL 1135 for additional flight control cable 
maintenance requirements.
InSTRUCTIOnS:
nOTE: Refer to the applicable Piper Maintenance Manual for model specific details.
1. Secure a jack stand to the tail skid (tie down). Visually inspect the entire length of the Stabilator flight control 
cable system, with special emphasis on the turnbuckle area, as described in the steps that follow.
2. Locate the rear cabin bulkhead, which is behind the aft seats. The rear cabin bulkhead is accessible from inside 
the aircraft.
nOTE: Temporary removal of seats and/or other interior components may be required to accomplish this 
inspection.
3. Remove and retain the access cover from the rear cabin bulkhead, in order to gain access to the tailcone area.
4. Identify the two (2) stabilator flight control cable turnbuckles, which are located inside the tailcone, directly aft 
of the rear cabin bulkhead. See Figure 1. Using procedures described in the appropriate Service/Maintenance 
Manual, disassemble the turnbuckle bodies to facilitate a complete inspection of the turnbuckle bodies and 
associated cable terminals.
5. Clean the turnbuckle bodies and associated cable terminals thoroughly with Methyl Ethyl Ketone (MEK) or 
acetone prior to inspection. The non-threaded surfaces of the turnbuckle body and cable terminals may be 
cleaned using Scotch-Brite™ General Purpose Green Scouring Pad 96 or 105b.
nOTE: Most of the affected aircraft use control cables featuring strands made of galvanized steel. By design, 
the galvanized coating corrodes sacrificially, protecting the steel strands underneath. This normal 
corrosion process creates zinc oxide powder, which can migrate along the length of the control 
cable, covering the surfaces of the turnbuckle components with an inert white speckled coating. This 
coating, along with any other contaminants such as dirt, oil or grease, must be removed in order to 
properly examine the turnbuckle and cable terminals.
6. Using a 10X magnifier, a mirror and a suitable light source, carefully examine the entire surface of each 
turnbuckle, cable terminal, and adjacent portion of the flight control cable, inspecting for cracks, corrosion, or 
broken cable strands. Any evidence of cracks or cable fraying, however minute, is cause for replacement. Any 
evidence of corrosion that remains after accomplishing the cleaning instructions above is cause for replacement.
7. Using procedures described in the appropriate Service/Maintenance Manual, reassemble the turnbuckle 
bodies and associated cable terminals. Rig and adjust stabilator travel and stabilator control cable tension. 
8. Reinstall the rear cabin bulkhead access cover, which was removed in Step 3. Reinstall any interior components 
that were removed in Step 2.
9. Remove the jack stand from the aircraft.
10. Make a logbook entry indicating compliance with this Service Bulletin.

### Page 3

SERvICE BULLETIn nO. 1245A PAGE 3 of 3
mATERIAL REQUIRED:
 Procure locally
 Methyl Ethyl Ketone (MEK) or acetone
 Scotch-Brite™ General Purpose Green Scouring Pad 96 or 105b
AvAILABILITy Of PARTS: N/A
EffECTIvITy DATE: This Service Bulletin is effective upon receipt.
SUmmARy: Please contact your Factory Authorized Piper Service Facility to make 
arrangements for compliance with this Service Bulletin in accordance with the 
compliance time indicated.
nOTE: Please notify the factory of any address/ownership corrections. Changes should include aircraft model, 
serial number, current owner’s name and address.
Corrections and/or changes should be directed to:
PIPER AIRCRAFT, INC. 
Attn:  Customer Service 
2926 Piper Drive 
Vero Beach, FL  32960
figure 1
Stabilator Control Cables (Typical)
To Stabilator
Turnbuckles
FWDOUTBD
UP

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
