# Piper Service Bulletin 1332: Revision A

- Rights: © Piper. Filed by the FAA in regulations.gov docket FAA-2019-0447; AD 2019-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Piper Service Bulletin 1332](https://openairdocs.org/service-documents/piper/sb-1332.md)
- Title as filed: SB 1332A
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/57/1b/571b5321a5e83d39be09cd05e75180826afbdd39af4072419b998307e7a1c276
- Page: https://openairdocs.org/service-documents/piper/sb-1332/file/571b5321a5e8

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

(OVER)
Date: October 16, 2018    (S)
SERVICE
 BULLETIN
NO.  1332
PIPER CONSIDERS
COMPLIANCE MANDATORY
ATA/JASC: 5312
Piper Aircraft, Inc.
2926 Piper Drive
Vero Beach, FL, U.S.A.  32960
SUBJECT: BULKHEAD RIVET REPLACEMENT
MODELS AFFECTED: SERIAL NUMBERS AFFECTED:
PA-46-600TP M600 4698001, 4698004 through 4698010,  
4698012 through 4698016, 4698018 through 4698076
COMPLIANCE TIME: 
Part I. Temporary Ground
Operating Limitation: Upon receipt, prior to next flight. Part I is to remain in effect until the aircraft is 
made compliant with Part II of this service bulletin.
Part II. Rework: To coincide with the next regularly scheduled maintenance event, but not to 
exceed the next 100 hours time in service. Compliance with Part II will remove the 
temporary operating limitation imposed by Part I of this service bulletin
APPROVAL: The engineering aspects of this service document have been shown to comply 
with the applicable Federal Aviation Regulations and are FAA approved.
PURPOSE: Part I of this service bulletin imposes a temporary ground operating limitation. 
Part II  mandates the replacement of specific rivets common to the fuselage 
station (FS) 79.00 bulkhead.  
SAFETY INTENT: As delivered from the factory, the FS 79.00 bulkhead on the affected aircraft does 
not have the required strength. Compliance with this service bulletin will ensure that 
loading conditions do not exceed the strength capability of the FS 79.00 bulkhead. 
Failure of the FS 79.00 bulkhead could result in loss of structural integrity of the 
airframe.
The safety intent of this service bulletin is to ensure that operating loads do not 
exceed the airframe capability at the affected area: 
• For short-term mitigation, airframe load is limited by completing Part I of this 
service bulletin.
• For long-term mitigation, the airframe conforms to type design strength by 
completing Part II of this service bulletin.
CONFIGURATION
DESCRIPTION: Part II of this service bulletin mandates the replacement of specific rivets in the FS 
79.00 bulkhead.

### Page 2

SERVICE BULLETIN NO.  1332 PAGE 2 of 11
INSTRUCTIONS:
NOTE:  Some steps in these instructions are identified as “required for compliance” (RC). If this service bulletin 
is mandated by an airworthiness directive (AD), the steps identified as RC must be done to comply with 
the AD. Steps not identified as RC are recommended and may be deviated from, done as a part of other 
actions, or done with accepted methods different from those given in this service bulletin, if the RC steps 
can be done and the airplane can be put back in a serviceable condition.
Part I. Temporary Ground Operating Limitation
NOTE:  The limitation provided in the attached temporary page for the pilot’s operating handbook (POH), and 
the related instrument panel placard, are precautionary until the aircraft is made compliant with Part 
II of this service bulletin. 
1. RC – Cut out and insert the temporary page from Figure 1  into the current PA-46-600TP POH VB–2366, 
after the existing page 2-1
2. RC – Temporary Placard
a. Order one (1) Placard – Ground Limitation, Piper part number (P/N) 46G110013-702, per aircraft. 
Alternatively, it is permissible to either 1) fabricate a placard or 2) utilize one of the placards in Figure 2:
1) Fabricate a placard from locally sourced materials, subject to the constraints listed below.
• The size of the placard shall be no greater than 0.75 inch high by 2.66 inches wide (3/4 x 2 1/3).
• The layout of the text shall agree with the example fabricated placard in Figure 2.
• The colors used shall be either white text on a matte black background, or black text on a white 
background.
• The font size shall be nine points (9 pt.) or larger.
• The text shall be comprised of all upper case (capital) letters.
• The typeface shall be chosen for its legibility. Examples include Alternate Gothic #2, Arial, Calibri, 
and Helvetica.
2) Print and cut out either of the example placards from Figure 2. Print the placard at the actual size.
For these alternatives, the printing material and adhesive used (e.g.: double-sided tape; clear, single-sided 
tape; or a suitable adhesive-backed material) is at the discretion of the owner/operator. The placard must be 
installed securely with none of its text concealed.
b. Install the placard onto the cockpit instrument panel in the location shown in Figure 3.
3. RC – Make a logbook entry documenting compliance with Part I of this service bulletin.

### Page 3

SERVICE BULLETIN NO.  1332 PAGE 3 of 11
ISSUED: June 17, 2016 REPORT: VB-2366
2-1a
 SECTION 2 
PA-46-600TP LIMITATIONS
REQUIRED UNTIL SB 1332 PART II COMPLIED WITH.
TEMPORARY GROUND OPERATIONS LIMITATION 
During ground operations including towing or taxiing, sharp turns are 
limited to groundspeeds below 10 knots. 
For PA-46-600TP airplanes serial numbers 
4698001, 4698004 through 4698010, 4698012 
through 4698016, and 4698018 through 4698076, 
the above limitation is imposed by Piper Service 
Bulletin 1332 Part I (latest revision) and must 
remain in effect until the airplane is made 
compliant with Piper Service Bulletin 1332 Part 
II (latest revision).
When the airplane is compliant with Piper 
Service Bulletin 1332 Part II (latest revision), 
this page may be removed.
WARNING
Figure 1
POH VB-2366 Temporary Page

### Page 4

SERVICE BULLETIN NO.  1332 PAGE 4 of 11
TEMP.  GROUND OPS. LIMITATION
REF SB1332 LATEST REV. 46G110013-702
SHARP TURNS LIMITED TO 10 KTS GS
P/N 46G110013-702
2.40
0.625
P/N 46G110013-702
TEMP.  GROUND OPS. LIMITATION
REF SB1332 LATEST REV. 46G110013-702
SHARP TURNS LIMITED TO 10 KTS GS
TEMP.  GROUND OPS. LIMITATION
REF SB1332 LATEST REV.
SHARP TURNS LIMITED TO 10 KTS GS 0.625
APPROX. 2.50
TEMP.  GROUND OPS. LIMITATION
REF SB1332 LATEST REV.
SHARP TURNS LIMITED TO 10 KTS GS 0.625
EXAMPLE FABRICATED PLACARD
EXAMPLE FABRICATED PLACARD
Figure 2
P/N 46G110013-702 and an Example of a Fabricated Temporary Placard
46F24A001
46F24A016-A
46G11A001-F Sh5
   
NXXXXX
STALL WARN
ICE SCHEDULE
(PRESS OFF)
SEE DETAIL  B
PLACARD 
P/N 46G110013-702
DETAIL  B
PLACARD 
P/N 46G110013-702
Figure 3
Instrument Panel – Temporary Placard Installation

### Page 5

SERVICE BULLETIN NO.  1332 PAGE 5 of 11
Part II. Rework
1. RC – Remove the main battery per Piper PA-46-600TP M600 Airplane Maintenance Manual (AMM), part 
number (P/N) 767-617, Section 24-30-00. 
NOTE:  At the discretion of the technician, the engine and engine mount may be removed as one assembly, 
rather than separately as the following two steps state. 
2. Remove the engine per Piper PA-46-600TP AMM P/N 767-617, Section 71-00-00.
3. Remove the engine mount assembly per Piper AMM P/N 767-617, Section 71-20-00. 
4. Remove the fuel filter assembly per Piper AMM P/N 767-617, Section 28-20-00.
5. Remove heat blankets, as necessary. 
6. Examine the entire surface of the bulkhead for damage. Any discovery of cracks, wrinkling, or missing rivets 
must be reported to Piper before proceeding. Contact Piper Customer Service to request the development of 
a suitable repair at (+1) 772-299-2141 or CustomerService@piper.com. Piper’s normal business hours are 
Monday through Friday, 7:30 a.m. to 4:30 p.m. (Eastern).
7. RC – Identify and remove all rivets within the highlighted areas in Figure 4, View B–B. 
To replace the single rivet identified in Figure 4, View C–C, it may be necessary to remove some or all of the 
rivets retaining two (2) Upper Tunnel Support Channels, P/N 103142-002 and 103144-002, which are identified 
in View C–C. View D–D shows the channel rivet locations and types. 
8. RC – Install the rivets shown in Table 1, as depicted in View B–B and, if necessary, View D–D, as replacements.
Ensure that a minimum edge distance of 0.32 inches is maintained for all rivets. 
Wet install all rivets with primer that conforms to MIL-PRF-85582D Type 1 Class C2, or, any one of the primers 
listed in Table 2.    
TABLE 1
REPLACEMENT RIVETS
QUANTITY PART NUMBER
BASIC CODE 
(per NAS523)
A/R MS20613-4P (See Note 1) LL
21 NAS1738M AAR
13 CR3523-5 (See Note 2) ASC
12 MS20613-5C LM
A/R MS20613-4C (See Note 3) LM
NOTE 1: Where MS20613-4P (LL) fasteners are specified, it is permissible to install 
oversize repair rivets MS20613-5P (LL), provided that a minimum edge distance 
of 0.32 inches is maintained.
NOTE 2: Optionally, NAS9307M-5 (AYS) rivets may be installed in place of CR3523-5 
rivets. 
NOTE 3:  Where MS20613-4C (LM) fasteners are specified, it is permissible to install 
oversize repair rivets MS20613-5C (LM), provided that a minimum edge distance 
of 0.32 inches is maintained. 
TABLE 2
ACCEPTABLE PRIMERS
Piper P/N Vendor Name Vendor Product No./Description
279-179 PPG Aerospace PRC-DeSoto EWDE072A/B
279-506 Akzo Nobel Aerospace Coatings 10P8-10NF/EC-283
279-108 Akzo Nobel Aerospace Coatings 10P30-5/EC-275
N/A Deft (PPG Industries) 44GN036
279-240 Axalta Coating Systems 13550S Epoxy Primer

### Page 6

SERVICE BULLETIN NO.  1332 PAGE 6 of 11
9. Reinstall the fuel filter assembly per Piper AMM P/N 767-617, Section 28-20-00. Reinstall all heat blankets that 
were removed.  
NOTE:  At the discretion of the technician, the engine and engine mount may be reinstalled as one assembly, 
rather than separately as the following two steps state. 
10. Reinstall the engine mount assembly per Piper AMM P/N 767-617, Section 71-20-00. 
11. Reinstall the engine per Piper AMM P/N 767-617, Section 71-00-00.
12. Reinstall the battery per Piper AMM P/N 767-617, Section 24-30-00. 
13. Remove the temporary page that was placed in the current PA-46-600TP POH, VB–2366, and the temporary 
placard that was installed on the instrument panel, as part of compliance with Part I of this service bulletin. 
14. RC – Make a logbook entry documenting compliance with Part II of this service bulletin.

### Page 7

SERVICE BULLETIN NO.  1332 PAGE 7 of 11
Figure 4, Sheet 1 of 4
Fastener Replacements
FS
132.00
FS
124.125
FS
117.00
FS
108.00
FS
100.00
FS
95.00
FS
53.75
FS
66.375
FS
79.00
FIREWALL
(REF)
SEE VIEW A
B
B
VIEW  A
ISOMETRIC VIEW SHOWING FS 79.00
(COMPONENTS REMOVED FOR CLARITY)
FWD
UP
FS
79.00
B
B

### Page 8

SERVICE BULLETIN NO.  1332 PAGE 8 of 11
Figure 4, Sheet 2 of 4
Fastener Replacements
DOUBLER
P/N 102172-003
(2)
(See Note 2,
Table 1)
9X ASC 5
(See Note 2,
Table 1)
4X ASC 5
ACCEPTABLE
AS IS
ACCEPTABLE
AS IS
P/N 102173-003
(REF)
P/N 102174-002 (REF)
6X LM 5 6X LM 5
C C
(See Note 3, 
Table 1)
A/R LM 4
A/R LM 4
(See Note 3, 
Table 1)
BL
0.00
BL
0.00
DOUBLER 
P/N 102172-004
(1)
DOUBLER 
P/N 46F531237-001
(2)
RIVET
(See View C–C)
A
Fig 4
Sh 2  A
Fig 4
Sh 3  
B
Fig 4
Sh 2  B
Fig 4
Sh 3  
VIEW  B−B
(SECTION 1 OF 2)
LOOKING AFT AT F.S. 79.00
BULKHEAD ASSEMBLY
VIEW  B−B
(SECTION 2 OF 2)
LOOKING AFT AT F.S. 79.00
BULKHEAD ASSEMBLY
NOTE:  All fasteners (rivets) in the 
highlighted areas are affected.

### Page 9

SERVICE BULLETIN NO.  1332 PAGE 9 of 11
Figure 4, Sheet 3 of 4
Fastener Replacements
DOUBLER
P/N 102172-003
(2)
(See Note 2,
Table 1)
9X ASC 5
(See Note 2,
Table 1)
4X ASC 5
ACCEPTABLE
AS IS
ACCEPTABLE
AS IS
P/N 102173-003
(REF)
P/N 102174-002 (REF)
6X LM 5 6X LM 5
C C
(See Note 3, 
Table 1)
A/R LM 4
A/R LM 4
(See Note 3, 
Table 1)
BL
0.00
BL
0.00
DOUBLER 
P/N 102172-004
(1)
DOUBLER 
P/N 46F531237-001
(2)
RIVET
(See View C–C)
A
Fig 4
Sh 2  A
Fig 4
Sh 3  
B
Fig 4
Sh 2  B
Fig 4
Sh 3  
VIEW  B−B
(SECTION 1 OF 2)
LOOKING AFT AT F.S. 79.00
BULKHEAD ASSEMBLY
VIEW  B−B
(SECTION 2 OF 2)
LOOKING AFT AT F.S. 79.00
BULKHEAD ASSEMBLY
NOTE:  All fasteners (rivets) in the 
highlighted areas are affected.

### Page 10

SERVICE BULLETIN NO.  1332 PAGE 10 of 11
Figure 4, Sheet 4 of 4
Fastener Replacements
VIEW  C−C
LOOKING UP AND AFT
CHANNELS TO REMOVE  TO REPLACE 
THE IDENTIFIED RIVET
CHANNEL
P/N 103144-002
CHANNEL
P/N 103142-002
RIVET
FWD
D
D
FWD
VIEW  D−D
LOOKING UP 
CHANNELS THAT MAY REQUIRE REMOVAL
OR SOME RIVETS REMOVED 
TO COMPLY WITH PART II 
A/R LL  4
(See Note 1,
Table 1)
A/R LL  4
(See Note 1,
Table 1)
AAR  4F
CHANNEL
P/N 103144-002
CHANNEL
P/N 103142-002

### Page 11

SERVICE BULLETIN NO.  1332 PAGE 11 of 11
MATERIAL REQUIRED: Per aircraft: 
For Part I: 
• One (1) Placard – Ground Limitation, Piper P/N 46G110013-702, or equivalent
• Attached, POH VB-2366 Temporary Page, Figure 1
For Part II, sufficient amounts (refer to Table 1): 
• Rivet, P/N MS20613-4P (LL), or, as required, P/N MS20613-5P (LL)
• Rivet, P/N MS20613-4C (LM), or, as required, P/N MS20613-5C (LM)
• Rivet, P/N MS20613-5C (LM)
• Rivet, P/N CR3523-5 (ASC), or P/N NAS1738M (AAR)
AVAILABILITY OF PARTS: Y our Piper Approved Service Center, or, procure locally
EFFECTIVITY DATE: This service bulletin is effective upon receipt.
SUMMARY: Applicable factory participation is limited to new aircraft in warranty at the time of 
compliance. Factory participation will remain in effect for a period of time not to 
exceed 180 days from the date of this service bulletin.
Please contact your Piper Approved Service Center to make arrangements for 
compliance with this service bulletin in accordance with the compliance time 
indicated.
NOTE: Please notify the factory of any address/ownership corrections. Changes should include aircraft model, 
serial number, and current owner’s name and address.
 Corrections and/or changes should be directed to:
PIPER AIRCRAFT, INC. 
Att’n:  Customer Service 
2926 Piper Drive 
Vero Beach, FL  32960
or: 
CustomerService@piper.com
Please include in subject line: “Aircraft ownership update”

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
