# Piper Service Bulletin 492: Revision A

- Rights: © Piper. Filed by the FAA in regulations.gov docket FAA-2014-0437; AD 2014-23-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Piper Service Bulletin 492](https://openairdocs.org/service-documents/piper/sb-492.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin 492A (RELEASE)
- Pages: 4
- PDF: https://openairdocs.org/files/sha256/9f/83/9f830d9139e9e56131300a249038c3b45d85542dd938a4653591b8e0f48b2e43
- Page: https://openairdocs.org/service-documents/piper/sb-492/file/9f830d9139e9

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin 492A supersedes Service Bulletin 492. Aircraft that have previously complied with Service Bulletin 
492 are already in compliance with Service Bulletin 492A. Service Bulletin 492A voids Service Letter 694 and 
Service Bulletin 430.
REASON FOR REVISION:  SB492A removes obsolete information about Turbine Tailpipe Coupling part 
numbers.
SUBJECT: TIGO-541-E1A EXHAUST SYSTEM MODIFICATION
MODELS AFFECTED: SERIAL NUMBERS AFFECTED:
PA-31P Pressurized Navajo 31P-1 to 31P-7400222 Inclusive, 31P-7400224 to 31P-
7630004 Inclusive, 31P-7630006 and 31P-7630007; 
(reference MATERIAL REQUIRED, below for individual 
modification kit/aircraft serial number applicability).
COMPLIANCE TIME: At the next regularly scheduled inspection interval (100 hour, annual or 
Programmed Inspection Event), not to exceed the next 100 hours of operation.
APPROVAL: The technical content of this Service Document has been shown to comply with 
the applicable Federal Aviation Regulations and is FAA approved.
PURPOSE: Throughout the operational life of the Pressurized Navajo, the TIGO-540-E1A 
exhaust system has been periodically refined and upgraded through a continuing 
program conducted jointly by the powerplant manufacturer - Lycoming, and Piper 
Aircraft to extend the service life of the exhaust system in general, and to alleviate 
specific reported conditions involving various exhaust system components. 
Thorough inspection procedures, in addition to required parts replacements were 
stressed in order to detect and replace unserviceable component attachments 
(couplings, clamps and brackets), vibration-induced tailpipe/exhaust pipe cracks, 
etc.
This service bulletin provides instructions and material (in addition to related 
reference data--see attached Lycoming publications) to consolidate and 
incorporate the latest exhaust system refinements on the above referenced aircraft. 
New material includes new exhaust transition couplings, new isolator assemblies, 
new support brackets, new exhaust manifold retainer assembly (reference 
Lycoming Service Bulletin No. 393C) and transition couplings replacement 
requirements, (reference Lycoming Service Bulletin No. 395). New materials 
are of heavy duty construction, designed to extend exhaust system component 
service life and reduce system maintenance/component parts replacements, as 
well as prevention of hazardous engine compartment conditions (fire hazard, etc.) 
resulting from exhaust system component failures. 
 SERVICE       NO.      492A
    BULLETIN
PIPER CONSIDERS
COMPLIANCE MANDATORY
Piper Aircraft, Inc.
2926 Piper Drive
Vero Beach, Florida, U.S.A.  32960
Date:   May 29, 2012           (M)
ATA: 7800 
(OVER)

### Page 2

SERVICE BULLETIN NO. 492A PAGE 2 of 3
INSTRUCTIONS: 
Prior to compliance activity, it is advisable to refer to the following service releases:
Source Type Number Topic Date
Piper Service Bulletin 462A Tailpipe Support Bracket Installation 11/3/75
Lycoming Service Bulletin 393C Exhaust Slip Joint Modification 2/6/76 
(attached)
Lycoming Service Bulletin 395 Exhaust Transition Coupling 
Replacement
3/5/76 
(attached)
Lycoming Service Instruction 1320 Tightening Procedure-Exhaust Manifold 
Components
3/7/75 
(attached)
1. Refer to attached sketch/instruction sheet (Figure 1) which illustrates the exhaust system components to be 
installed or replaced (references: Piper Service Bulletin No. 462A, Lycoming Service Bulletin Nos. 393C and 
395 attached.
When reattaching turbine tailpipe to tailpipe support bracket, proceed as follows: Position existing tailpipe 
support clamp around tailpipe and support bracket. Deflect upper end of bracket approximately 1/8 inch away 
from turbine housing and tighten clamp so as to preload the tailpipe flange against the turbine flange. Torque 
clamp nut to 25 – 35 in-lbs.
2. Reference attached Lycoming Service Instructions No. 1320 Exhaust Manifold Components Tightening 
Procedures.
3. Inspect complete exhaust system for cracks, exhaust leakage evidence, looseness at joints, etc; correct as 
required.
4. Make appropriate log book entry indicating compliance with this service bulletin; be sure to record compliance 
with other service releases referred to in this release.
MATERIAL REQUIRED:
1. One (1) each per aircraft (i.e., both engines) Piper kit P/N 761-045, Tailpipe Isolator Replacement, applies to 
the following aircraft configurations:
a. Serial numbers 31P-1 to 31P-7400216 inclusive if Piper kit P/N 760-837 has been previously installed per 
Piper Service Letter 694; and
b. Serial numbers 31P-7400217 to 31P-7400222 inclusive, 31P-7400224 to 31P-7630004 inclusive, 31P-
7630006 and 31P-7630007.
2. One (1) each per aircraft (i.e., both engines) Piper kit P/N 761-046, Tailpipe Support Installation (contains new 
turbine tailpipe to wastegate tailpipe isolators), and one (1) each per aircraft (i.e., both engines) Piper kit P/N 
761-047, Tailpipe Isolator Replacement (contains new isolators to replace existing turbine tailpipe to exhaust 
transition isolators); both kits required for aircraft serial numbers 31P-1 to 31P-7400216 inclusive if Piper kit 
P/N 760-837 has NOT been previously installed per Piper Service Letter 694.
3. Per Piper Service Bulletin 462A - one (1) each per aircraft Piper kit P/N 760-974, Tailpipe Support Bracket 
Installation applicable to aircraft serial numbers 31P-1 to 31P-7630009 that have not yet complied with Service 
Bulletin 462A.
4. Refer to Lycoming Service Bulletins 393C and 395 for related material requirements.

### Page 3

SERVICE BULLETIN NO. 492A PAGE 3 of 3
AVAILABILITY OF PARTS: Y our Piper Service Facility.
EFFECTIVITY DATE: This Service Bulletin is effective upon receipt.
SUMMARY: Please contact your Factory Authorized Piper Service Facility to make 
arrangements for compliance with this Service Bulletin in accordance with the 
compliance time indicated.
NOTE: Please notify the factory of any address/ownership corrections.  Changes should include aircraft model, 
serial number, current owner’s name and address.
Corrections and/or changes should be directed to:
PIPER AIRCRAFT, INC. 
Attn:  Customer Service 
2926 Piper Drive 
Vero Beach, FL  32960
Figure 1
Tailpipe Support Bracket & Clamp
(Ref: Piper Service Bulletin 462A)
Turbine Tailpipe
Turbine Housing
Exhaust Transition Assembly
New Isolator Assembly
(Contained in Piper Kits
761-045 and 761-047)Exhaust Slip Joint Retainer
(Ref: Lycoming Service Bulletin 393C)
Exhaust Pipe
Exhaust Transition Coupling Replacement
(Ref: Lycoming Service Bulletin 395)
Exhaust Slip Joint Retainer
(Ref: Lycoming Service Bulletin 393C)
New Isolator Assembly
(Contained in Piper Kits 761-045 & 761-046) Wastegate Tailpipe

### Page 4

SERVICE BULLETIN NO.  492A
DATED: May 29, 2012
BULLETIN SUPPLEMENT - PROCEDURAL OPERATING INFORMATION
MATERIAL ALLOWANCE: N/A
LABOR ALLOWANCE: N/A
DISPOSITION OF PARTS IN STOCK: N/A
DISPOSITION OF PARTS REPLACED: N/A

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
