# Robinson Service Letter R44 74: Revision B

- Rights: © Robinson. Filed by the FAA in regulations.gov docket FAA-2024-1477, the docket of AD 2024-23-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Robinson Service Letter R44 74](https://openairdocs.org/service-documents/robinson/sl-r44-74.md)
- Title as filed: Robinson R44 Service Letter SL-74B and SL-61B
- Pages: 4
- PDF: https://openairdocs.org/files/sha256/10/9c/109c428e9a677667f897dda8b01c70ea0182db762defeb312ec421dbcb7a90e2
- Page: https://openairdocs.org/service-documents/robinson/sl-r44-74/file/109c428e9a67

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ROBINSON
HELICOPTER COMPANY
2901 Airport Drive, Torrance, California 90505  Phone (310) 539-0508 Fax (310) 539-5198
Page 1 of 4
R22 SERVICE LETTER SL-74B
(supersedes R22 SL-74A)
R44 SERVICE LETTER SL-61B
(supersedes R44 SL-61A)
DATE: 21 July 2017  REV B: 16 March 2023
TO: R22-series & R44-series Owners, Operators, and Maintenance Personnel
SUBJECT: Riveted A185 Brackets Installation & Fiberglass Scroll Repair;
does not apply to A185 brackets attached with (12) steel, hex-drive screws.
BACKGROUND: Perform whenever looseness of a riveted A185 bracket is detected or
suspected, and whenever upper or lower scroll is removed. Refer to R44 SB-113.
COMPLIANCE PROCEDURE:
1. Remove fanwheel per Maintenance Manual (MM) Chapter 6. Clean both scrolls.
NOTE
If available, the removable bearing block [housing] from an R22's
A007-5 fanshaft assembly can be used as an A185 bracket
alignment fixture on both R22 & R44 scrolls. Refer to R22 MM §
22-42 for bearing housing removal & installation instructions.
2. Refer to Figure 1. Inspect A185 brackets on scroll. Proceed to step 4 if any A185
bracket exhibits looseness or signs of movement.
3. If all three A185 brackets are secure on scroll:
a. Evaluate condition of fiberglass adjacent to rivets. If fiberglass is delaminated
replace scroll and install per step 5 & subsequent.
b. Refer to Figure 1. Count rivets attaching three A185 brackets to scroll. If less
than 3 rivets at any location (4 places), install middle 5/32-inch [shank] diameter
rivets centered between existing rivets as shown. Replace all existing 1/8-inch
diameter rivets with 5/32-inch diameter rivets. Proceed to step 18.
NOTE
MS20470AD5 universal-head rivets have minimum 0.296-inch diameter head.
MS20426AD5 countersunk-head rivets have minimum 0.282-inch diameter head
(OVER)

### Page 2 (OCR)

R22 SL-74B
R44 SL-61B
Page 2 of 4
3X 0.158-0.164 inch dia. holes
A185-3 Plate  3X MS20470AD5 rivets
(4 places)  2 places
(add middle rivets if not previously
installed)
A185-2-  • A185-5 Bracket
Bracket  - Upper scroll
- A181/C181 Lower bearing
Lower
scroll
A185-1
Bracket  •AN3-41A Bolt
1) NAS620-10L Washer
2 places
2X MS20470AD5 rivets  4X 0.290 inch dia. x 100° countersink
4X MS20426AD5 rivets
6X 0.158-0.164 inch dia. holes  (add middle rivets if not previously
installed)
FIGURE 1
CAUTION
Use proper personal protective equipment when handling fiberglass.
4. If any of three A185 brackets are loose on scroll, or exhibits signs of movement:
a. Remove all brackets and inner plates by drilling out attaching rivets.
b. Visually inspect brackets and plates for cracks & deformation; replace damaged
parts.
c. Evaluate condition of fiberglass adjacent to rivet holes. If fiberglass is delaminated
replace scroll and install per step 5 & subsequent.
d. Repair (fill) all rivet holes in scroll per U.S. FAAAC 43.13-1B para 3-3.a (online at
www.faa.gov). Scroll material is Style 7533, plain weave, 18x18 threads/inch, 5.8
ounce/sq.yard, fiberglass cloth with polyester resin; for repair purposes, epoxy
resin is recommended instead of polyester resin.
5. Apply a light coating of layout dye (or contrasting lacquer paint) to upper scroll in
area where A181/C181 bearing resides.
6. Remove lower sheave per MM § 7.290.

### Page 3 (OCR)

R22 SL-74B
R44 SL-61B
Page 3 ot 4
7. Rotate crankshaft using starter ring-gear support until largest diameter bushing
in crankshaft flange (typically stamped "O" adjacent) is at 12 o'clock position and
bushing bore is visually aligned with crankcase split line.
8. Without moving crankshaft, loosen alternator belt and remove starter ring gear
support.
9. Install (3) NAS1149F1290P (AN960-1216) washers on each crankshaft flange
bushing at 2-, 6-, & 10-o'clock positions (washers substitute for thickness of removed
starter ring gear support).
10. Without moving crankshaft, install lower sheave and fan shaft & bearing assy on
crankshaft using bolts at 2-, 6-, & 10-o'clock positions. Hand tighten bolts.
11. Refer to Figure 2. Visually align actuator mounting holes in A181/C181 bearing
housing with upper empty bolt hole in crankshaft. Insert a sufficiently long & straight
0.250-inch diameter drill (or straight, pointed-screwdriver shank) thru holes in bearing
housing until drill point contacts crankcase, then rotate bearing housing as required
until drill point aligns with crankcase split line. Prevent bearing housing rotation with
duct tape. Cut off the portion of drill shank protruding beyond bearing housing.
12. Position upper scroll on engine and secure corners to cooling panels with at least 6
screws & nuts.
13. Verify drill point in bearing housing remains aligned with crankcase split line; correct
housing/drill position as required then immobilize housing. Using suitable scribe,
trace outline of A181/C181 bearing housing into layout dye on upper scroll.
14. Remove drill, duct tape, upper scroll half, fanshaft & bearing assembly, lower sheave,
and washers.
15. Refer to Figure 1. Assemble upper & lower scroll halves with screws. Assemble and
secure (3) A185 brackets to A181/C181 bearing housing with AN3-41A bolts and
washers. Align bearing housing and attached brackets with scribed lines on upper scroll.
16. Using A185 brackets as a guide, progressively drill twelve 0.158/0.164 inch diameter
holes thru brackets, scroll, and plates, countersink brackets as required & install
solid rivets per Figure 1.
17. Remove AN3-41A bolts, disassemble scroll halves, and clean up debris. Remove
layout dye and paint scroll as required.
18. Install alternator belt (a new alternator belt is recommended), starter ring gear
support, lower sheave and fanshaft & bearing assembly per MM § 7.290.
19. Install fanwheel per MM § 6.220. On lower A185 bracket, apply torque seal in a
horizontal stripe across both outboard rivets to lower scroll to facilitate future
inspections.
20. Make appropriate maintenance record entries.
(OVER)

### Page 4 (OCR)

R22 SL-74B
R44 SL-61B
Page 4 of 4
LYCOMING
ENGINE
Crankcase split
Long, 0.250 inch diameter drill
A181/C181 Bearing housing
Cut off protruding drill shank
VIEW LOOKING DOWN
(R22 shown, R44 is similar)
FIGURE 2

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
