# Rolls-Royce Mandatory Service Bulletin 72-AL165: No revision named

- Rights: © Rolls-Royce plc. Filed by the FAA in regulations.gov docket FAA-2024-2664, the docket of AD 2024-25-10. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Rolls-Royce Mandatory Service Bulletin 72-AL165](https://openairdocs.org/service-documents/rolls-royce/72-al165.md)
- Title as filed: Rolls-Royce Non Mandatory Service Bulletin 72-AL165
- Pages: 22
- PDF: https://openairdocs.org/files/sha256/fe/50/fe504252a07c4ede5e479601e51dc076bee07a0e5b082322c2c7747b5b251a00
- Page: https://openairdocs.org/service-documents/rolls-royce/72-al165/file/fe504252a07c

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

This document transmits the Initial Issue of Service Bulletin TRENT XWB 72-AL165
Bulletin Initial Issue
Remove Incorporate Reason for change
Pages 1 to 20 of the
Service Bulletin
Initial Issue
P.O. Box 31, Derby
DE24 8BJ, UK
Tel: +44 (0) 1332 242424
This Rolls-Royce Technical Publication is
subject to export control as follows:
Jurisdiction: UK
Export Classification: PL9009c
The technical information contained in this document has been approved under the authority of - See Planning
Information, Approval.
Date: September 05, 2024
TRENT XWB SERIES PROPULSION SYSTEMS NON-MODIFICATION SERVICE BULLETIN
ALERT TRENT XWB 72−AL165
Transmittal - Page 1
of 2
CHECK THAT ALL PREVIOUS TRANSMITTALS HAVE BEEN INCORPORATED
If any have not been received please advise customersupport@rolls-royce.com.
© 2024 Rolls-Royce plc
P   U   B   L   I   C   A   T   I   O   N          T   R   A   N   S   M   I   T   T   A   L
ALERT

### Page 2

LIST OF EFFECTIVE PAGES
The effective pages to this Service Bulletin are as follows:
Page Revision Number Revision Date
Bulletin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
Sep. 5/2024
ALERT TRENT XWB 72−AL165
Transmittal - Page
2 of 2

### Page 3

ENGINE - FUEL MANIFOLD - ONE TIME INSPECTION OF THE MAIN FUEL HOSE ASSEMBLY -
NON-MODIFICATION SERVICE BULLETIN - NON - MOD.72-AL165
1. Planning Information
A. Effectivity
Airbus A350
All TRENT XWB-97 Engines, except Engine Serial Number 26023, 26024, 26025, 26026, 26029,
26033, 26035, 26036, 26039, 26040, 26041, 26042, 26043, 26047, 26048, 26052, 26053, 26058,
26059, 26061, 26062, 26069, 26070, 26104, 26114, 26132, 26133, 26142, 26156, 26206, 26207,
26212, 26213, 26250.
B. Reason
(1) Problem
Following an in-flight shutdown on a Trent XWB-97 engine this Non-Modification Service Bulletin
(NMSB) introduces an initial inspection of the fuel manifold main fuel hose assembly.
(2) Safety Intent
The safety intent of this NMSB is to identify and remove damaged fuel manifold main fuel hose
assemblies from service which, if not accomplished, could lead to a fuel leak and a subsequent
in-flight event.
C. Description
This NMSB is issued to instruct a one-off visual and dimensional inspection of the Trent XWB engine
of the fuel manifold main fuel hose assembly for damage. The NMSB includes specific inspection
tasks and accept / reject limits.
Accomplishment of this NMSB should be recorded in accordance with local NMSB tracking
procedures.
The feedback sheet in Appendix 1 (or similar form) should be completed and returned to your
Rolls-Royce Airline Support Team (AST) upon completion of the Accomplishment Instructions and a
copy emailed to TrentXWB_ServiceEngineering@Rolls-Royce.com (Trent XWB Service Engineering
inbox). The text ’NMSB 72-AL165 must be included in the subject line of the return email.
D. Compliance
(1) On-Wing
ALERT
ALERT TRENT XWB 72−AL165
Page 1
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 4

(a) On-wing installed engines, carry out accomplishment instructions in Section 3.A no later
than the Compliance Time defined in Table 1.
Group Engine Criteria Compliance Time
1
Engines with Hours Since New
greater than or equal to 18,500 that
have had 2 or more previous shop
visits (Hospital, Check & Repair,
Refurbishment or Overhaul)
OR
Engines with Cycle Since New
greater than or equal to 2,300 that
have had 2 or more previous shop
visits (Hospital, Check & Repair,
Refurbishment or Overhaul)
3 days from date of Issue of NMSB
2
Engines which are not in group 1,
which have had a previous shop visit
(Hospital, Check & Repair,
Refurbishment or Overhaul)
7 days from date of Issue of NMSB
3 Engines not in group 1 or group 2 30 days from date of Issue of NMSB
Table 1: Required Compliance Time
(b)
Engines which are not installed on aircraft, carry out accomplishment instructions in
Section 3.A prior to installation.
(2) In-Shop
Not Applicable.
E. Approval
NMSB 72-AL165 was approved by Rolls-Royce on Sep. 5/2024. The technical content of this
document is approved under the authority of the DOA ref. EASA.21J.065.
F. Manpower
(1) On-Wing
(a)
Time to gain access
0.25 man-hours (1 person x 0.25 hours) - (Estimated).
(b) Time to inspect
2 man-hours (1 person x 2 hours) - (Estimated).
(c) Time to restore to serviceable condition
0.25 man-hours (1 persons x 0.25 hour(s)) - (Estimated).
(2) In-Shop
Not Applicable.
NOTE: The parts affected by this NMSB are accessible On-Wing.
ALERT TRENT XWB 72−AL165
Page 2
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 5

G. Material Price and Availability
Prices available on request.
H. Tooling Price and Availability
Tooling required to accomplish this Non-Modification Service Bulletin if fuel manifold main fuel hose
assembly is found to be damaged:
(1) Vernier gauge (No specific) - 1 off.
(2) HU38837 Plier - 1 off.
(3) RRT028932 Crimping Plier - 1 off.
(4) RRT102260 Immobiliser - 1 off.
(5) RRT102591 Immobiliser Kit - 1 off.
(6) RRT071379-1 Spanner - 1 off.
(7) RRT071380-1 Spanner - 1 off.
(8) RRT102261 Immobiliser - 1 off.
(9) RRT102262 Immobiliser - 1 off.
(10) RRT102263 Immobiliser - 1 off.
(11) RRT102259 Immobiliser - 1 off.
(12) RRT102258 Immobiliser - 1 off.
(13) RRT102257 Immobiliser - 1 off.
(14) RRT102256 Immobiliser - 1 off.
(15) Access platform 3M (10 FT) - Adjustable - 2 off.
(16) Torque wrench range to between 4.52 and 4.98 m.daN (33.34 and 36.73 lbf.ft) - As required.
(17) Torque wrench range to between 3.49 and 3.85 m.daN (25.74 and 28.40 lbf.ft) - As required.
I. References
(1) Maintenance Procedures (MP):
(a)
A350-A-71-XX-XX-06001-398A-A - List of Power-Plant Maintenance Practices.
(b) A350-A-72-41-65-00001-520A-A - Removal of the Main Fuel Hose-Assembly from the Fuel
Manifold.
(c) A350-A-72-41-65-00001-720A-A - Installation of the Main Fuel Hose-Assembly on the Fuel
Manifold.
ALERT TRENT XWB 72−AL165
Page 3
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 6

2. Material Information
A. Parts that may be required to accomplish this NMSB.
72-41-71, refer to Engine Illustrated Parts Catalogue
FIG ITEM NO. QTY PART TITLE PART NO.
01 192 10 O ring packing M83485-1-112
01 195 10 Washer FK11864
01 392 10 O ring packing M83485-1-112
01 395 10 Washer FK11864
02 250 6 RH-MAIN FUEL HOSE PH11181-2CLS
02 265 1 RH-MAIN FUEL HOSE PH11179-2CLS
02 280 2 RH-MAIN FUEL HOSE PH11180-2CLS
02 295 1 RH-MAIN FUEL HOSE PH11182-2CLS
02 500 6 LH-MAIN FUEL HOSE PH11176-2CLS
02 515 2 LH-MAIN FUEL HOSE PH11177-2CLS
02 530 1 LH-MAIN FUEL HOSE PH11178-2CLS
02 545 1 LH-MAIN FUEL HOSE PH11183-2CLS
72-41-72, refer to Engine Illustrated Parts Catalogue
FIG ITEM NO. QTY PART TITLE PART NO.
01 178 18 O ring packing M83485-1-110
01 198 2 O ring packing M83485-1-110
01 240 20 Sealing ring M83485-1-114
01 285 20 Washer UP10274
B. Consumable items required to accomplish this NMSB if fuel manifold main fuel hose assembly is
found to be damaged:
Reference QTY Designation
OMat 2-142 As required Safety cable
ALERT TRENT XWB 72−AL165
Page 4
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 7

3. Accomplishment Instructions
GENERAL
NOTE: When the words “refer to” are used in the Accomplishment Instructions and there are other
acceptable methods, techniques and practices (including tools, equipment and test
equipment) those acceptable methods, techniques and practices (including tools, equipment
and test equipment) can be used to complete the work, however Rolls-Royce plc always
recommends to use the procedures referred to in the Accomplishment Instructions. When
the words “in accordance with
” are used in the Accomplishment Instructions, the methods,
techniques and practices (including tools, equipment and test equipment) in the specified
document must be used.
A. On-Wing - Visual and dimensional inspection of the fuel manifold main fuel hose assembly.
WARNING: YOU MUST BE CAREFUL WHEN YOU WORK ON THE ENGINE AFTER THE ENGINE IS
SHUTDOWN. THE ENGINE CAN STAY HOT FOR ALMOST ONE HOUR.
WARNING: YOU MUST NOT TOUCH HOT PARTS WITHOUT APPLICABLE GLOVES. HOT PARTS CAN
CAUSE INJURY. IF YOU GET AN INJURY, PUT IT IN COLD WATER FOR 10 MINUTES.
THEN GET MEDICAL AID.
WARNING: YOU MUST NOT LET ENGINE FUEL STAY ON YOUR SKIN. FLUSH THE FUEL FROM
YOUR SKIN WITH WATER. THE FUEL IS POISONOUS AND CAN BE ABSORBED INTO
YOUR BODY.
WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR
AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY
AND CAUSE AN INJURY AND/OR DAMAGE.
CAUTION: YOU MUST NOT LET ENGINE FUEL FALL ON THE ENGINE. UNWANTED FUEL MUST BE
REMOVED IMMEDIATELY WITH A CLEAN LINT-FREE CLOTH. THE FUEL CAN CAUSE
DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
CAUTION: YOU MUST NOT PUT FUEL THAT HAS BEEN DRAINED FROM THE ENGINE BACK INTO
THE FUEL SYSTEM. CONTAMINATION IN THE FUEL CAN CAUSE DAMAGE TO SOME
PARTS.
CAUTION: YOU MUST NOT BEND THE FLEXIBLE HOSE SECTIONS OF THE FUEL MANIFOLD
ASSEMBLY TOO MUCH WHEN YOU DISCONNECT/CONNECT THEM. IF YOU DO NOT
OBEY THIS INSTRUCTION, DAMAGE TO THE FUEL MANIFOLD ASSEMBLY CAN OCCUR.
CAUTION: IN ORDER TO REDUCE THE POTENTIAL FOR MULTIPLE ENGINE IN FLIGHT
SHUTDOWN, POWER LOSS OR OTHER ANOMALIES DUE TO MAINTENANCE ERROR,
ROLLS-ROYCE RECOMMENDS THAT OPERATORS AVOID PERFORMING
MAINTENANCE ON MULTIPLE ENGINES INSTALLED ON THE SAME AIRCRAFT AT THE
SAME TIME. IF IT IS NOT POSSIBLE TO AVOID MAINTENANCE ON MORE THAN ONE
ENGINE AT THE SAME TIME, ROLLS-ROYCE RECOMMENDS THAT ADDITIONAL
CONTROLS ARE APPLIED IN ORDER TO ENSURE THAT MAINTENANCE TASKS HAVE
BEEN COMPLETED AS DEFINED. MAINTENANCE GUIDELINES SHOULD BE REVISED,
WHERE POSSIBLE, TO PROMOTE THIS RECOMMENDATION.
(1) Prepare the engine to gain access to visually inspect the main fuel hose. Refer to
A350-A-72-41-65-00001-520A-A Section 3.
ALERT TRENT XWB 72−AL165
Page 5
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 8

(2) Inspection of the fuel manifold main fuel hose 1 to 20.
(a)
Apply pressure to the middle third of the free hose length, perpendicular to the bend in the
installed condition, using thumb and forefinger, refer to Figure 1 and Figure 2.
[1] If any softness, compliance or lack of resistance is identified proceed to 2 (b).
[2] If the above criteria is not met proceed to 2 (c).
(b) Do a dimensional inspection of the middle third of the free hose length, perpendicular to
the bend in the installed condition, with vernier gauge (no specific), refer to Figure 1,
Figure 2, Figure 3 and Figure 4.
CAUTION: YOU MUST NOT PUT TOO MUCH PRESSURE ON THE TUBE WHEN USING
VERNIER GAUGE, IF YOU DO NOT OBEY DAMAGE TO TUBE MAY OCCUR.
[1] Firmly push the vernier gauge (no specific) by hand, to compress the outer braid and
measure and record the reading in Appendix 1 Table 2 or similar form.
[2] If the vernier gauge measurement is more than 12.0 mm (0.47 in.) accept the hose,
and proceed to Step (c).
[3] If the vernier gauge measurement is less than or equal to 12.0 mm (0.47 in.), replace
the hose in accordance with 3.A.(3) within 10 flight cycles, and proceed to Step (c).
(c)
Do a visual inspection of the full length of the fuel hoses for damage.
[1] Examine the fuel hose braid for cracking.
[a] If no braid cracks are found, proceed to (c)[2].
[b] Reject the main fuel hose if cracks are found. Replace before next flight.
[2] Examine the fuel hoses for chafing.
[a] If there are no signs of chafing or if the chafing does not expose the white
e-glass insulator, proceed to (c)[3].
[b] Reject the main fuel hose if the white e-glass insulator is exposed. Replace
before next flight.
[3] Examine the fuel hoses for dents.
[a] If dents are less than 2.54 mm (0.10 in.) in depth, proceed to (c)[4].
[b] Reject the main fuel hose if dents are found above 2.54 mm (0.10 in.) in depth.
Replace before next flight.
[4] Examine the fuel hoses for kinks, refer to Figure 5.
NOTE: Kinks are bent deformations of the tube assembly that do not agree with
the circular tube contour when new. Kinks could decrease and/or stop the
flow of fluid through the tube.
[a] If no kinks are found, proceed to (c)[5].
[b] Reject the main fuel hose if kinks are found. Replace before next flight.
ALERT TRENT XWB 72−AL165
Page 6
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 9

[5] Examine the fuel tubes for Necking, refer to Figure 6.
NOTE: Necking occurs when the tube assembly is stretched and its diameter is
less than it was when the part was new. Necking occurs around the entire
360 degrees circumference of the braid.
[a] If no Necking is found, proceed to (c)[6].
[b] Reject the main fuel hose if necking is found. Replace before next flight.
[6] Examine the braid wire of the hoses, refer Figure 7 to Figure 11.
[a] If there are signs of local necking or long insulation strands that have come out
from the outer braid, reject the main fuel hose. Replace before next flight.
[b] Bent wire that goes across more than three adjacent wire plaits, reject the main
fuel hose. Replace before next flight.
[c] Any broken wire, reject the main fuel hose. Replace before next flight.
[d] Collar area around the crimp zone is embedded in to braid, reject the main fuel
hose. Replace before next flight.
(3) If the main fuel hose is rejected, remove the damaged main fuel hose and install a new main fuel
hose.
CAUTION: MAKE SURE THAT ONLY THE TOOLING SPECIFIED IN THE MAINTENANCE TASKS
ARE USED FOR REMOVAL AND INSTALLATION.
(a)
Remove the main fuel hose from the fuel manifold, refer to
A350-A-72-41-65-00001-520A-A.
(b) Install a new main fuel hose on the fuel manifold, refer to A350-A-72-41-65-00001-720A-A.
(c) Do the applicable test Ref. MP A350-A-71-XX-XX-06001-398A-A.
(4) Close the access and return engine and aircraft back to initial configuration. Refer to
A350-A-72-41-65-00001-720A-A Section 5.
(5) Record accomplishment of this NMSB in accordance with local Service Bulletin tracking system
procedures.
ALERT TRENT XWB 72−AL165
Page 7
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 10

dex8000665
A
VIEW WHEN YOU LOOK FROM THE REAR OF THE ENGINE
1
2
20
19
18
17
16
15
14
13
12
11 10
9
8
7
6
5
4
3
A
1 22019
18
17
16
15
14
13
12
11 10 9
8
7
6
5
4
3
General Arrangement of Fuel Manifold Main Fuel Hose
Figure 1
ALERT TRENT XWB 72−AL165
Page 8
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 11

FUEL MANIFOLD
MAIN FUEL HOSE
PH11181−2CLS
72−41−71
02−250
PH11179−2CLS
72−41−71
02−265
PH11180−2CLS
72−41−71
02−280
PH11182−2CLS
72−41−71
02−295
PH11176−2CLS
72−41−71
02−500
PH11177−2CLS
72−41−71
02−515
PH11178−2CLS
72−41−71
02−530
PH11183−2CLS
72−41−71
02−545
dex8000666
FUEL MANIFOLD
MAIN FUEL HOSE
PH11181−2CLS
72−41−71
02−250
PH11179−2CLS
72−41−71
02−265
PH11180−2CLS
72−41−71
02−280
PH11182−2CLS
72−41−71
02−295
PH11176−2CLS
72−41−71
02−500
PH11177−2CLS
72−41−71
02−515
PH11178−2CLS
72−41−71
02−530
PH11183−2CLS
72−41−71
02−545
Fuel Hose Dimensional Inspection
Figure 2
ALERT TRENT XWB 72−AL165
Page 9
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 12

dex8000667
Example for Dimensional Inspection Accept
Figure 3
ALERT TRENT XWB 72−AL165
Page 10
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 13

dex8000668
Example for Dimensional Inspection Reject within 10 Flight Cycles
Figure 4
ALERT TRENT XWB 72−AL165
Page 11
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 14

dex8000670
NOT ACCEPTABLE
KINK
Example for Kink
Figure 5
ALERT TRENT XWB 72−AL165
Page 12
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 15

dex8000671
NOT ACCEPTABLE
NECKING
CONTOUR
WHEN NEW
Example for Necking
Figure 6
ALERT TRENT XWB 72−AL165
Page 13
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 16 (OCR)

R
ROTSE
NOTE:
HOSES THAT HAVE SIGNS OF LOCAL NECKING OR LONG INSULATOR STRANDS
THAT HAVE COME THROUGH THE OUTER BRAID AS SHOWN ARE UNSERVICEABLE.
NOTE:
A SMALL AMOUNT OF INSULATION SHOWN THROUGH OUTER BRAID IS PERMITTED.
dex8000672
Example for Braid Damage Accept / Reject
Figure 7
Sep. 5/2024, Initial Issue  ALERT TRENT XWB 72-AL165
Page 14 of 20
© 2024 Rolls-Royce p/c

### Page 17

dex8000673
GOUGES AND HEAVY
SCRAPE MARKS
ACROSS INDIVIDUAL
WIRES CAN CAUSE
BROKEN WIRES
NOTE:
TWISTED WIRES (OR WIRE CROSSOVER) IS PERMITTED. BENT WIRES IN A SINGLE PLAIT
IS PERMITTED. BENT WIRE THAT GOES ACROSS MORE THAN THREE ADJACENT WIRE
PLAITS IS UNSERVICEABLE.
Example for Braid Wire Twist Accept / Reject
Figure 8
ALERT TRENT XWB 72−AL165
Page 15
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 18

dex8000674
Example for Braid Broken Wire
Figure 9
ALERT TRENT XWB 72−AL165
Page 16
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 19

dex8000675
NOTE:
SMALL WAVINESS ONLY APPLIES TO THE "COLLAR" AREA AROUND THE CRIMP ZONE.
SERVICEABLE
Example for Collar Waviness Acceptance
Figure 10
ALERT TRENT XWB 72−AL165
Page 17
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 20

dex8000676
NOTE:
"COLLAR" AREA AROUND THE CRIMP ZONE IS EMBEDDED INTO THE BRAIDED HOSE.
UNSERVICEABLE
Example for Collar Waviness Reject
Figure 11
ALERT TRENT XWB 72−AL165
Page 18
of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 21

Appendix 1
This form (or similar) is to be completed for every engine/component inspected.
Return this form (or similar) to your local Rolls-Royce Service Representative as soon as you complete the
inspection for recording into Rolls-Royce internal system.
Feedback Sheet NMSB 72-AL165
Operator
Aircraft Tail Number
Engine Serial Number
Engine Hours Since New
Engine Cycles Since New
Fuel Hose Part Number Vernier gauge
measurement
(if measured)
Part Accept /Reject Reason for
Rejection
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ALERT TRENT XWB 72−AL165
Appendix 1
- Page 19 of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

### Page 22

Table 2
ALERT TRENT XWB 72−AL165
Appendix 1
- Page 20 of 20
Sep.  5/2024, Initial Issue
© 2024 Rolls-Royce plc

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
