# Rolls-Royce Service Bulletin 72-K570: No revision named

- Rights: © Rolls-Royce plc. Filed by the FAA in regulations.gov docket FAA-2021-1164, the docket of AD 2022-08-16. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Rolls-Royce Service Bulletin 72-K570](https://openairdocs.org/service-documents/rolls-royce/72-k570.md)
- Title as filed: Rolls-Royce Trent 1000 SB 72-K570
- Pages: 58
- PDF: https://openairdocs.org/files/sha256/7b/98/7b98993a7111b4cfd3e3918b8902656835c72236e309e9d10cb7208324ed1460
- Page: https://openairdocs.org/service-documents/rolls-royce/72-k570/file/7b98993a7111

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

This document transmits the Initial Issue of Service Bulletin TRENT1000-72-K570
and the Initial Issue of the Supplement
Bulletin Initial Issue
Remove Incorporate Reason for change
Pages 1 to 54 of the
Service Bulletin
Initial Issue
Supplement Initial Issue
Remove Incorporate Reason for change
Page 1 Initial Issue
Printed in Great Britain
Jun.15/21
TRENT 1000 SERIES PROPULSION SYSTEMS SERVICE BULLETIN
TRENT 1000 72−K570
Transmittal - Page 1 of 3
Date

### Page 2

LIST OF EFFECTIVE PAGES
The effective pages to this Service Bulletin are as follows:
Page Revision Number Revision Date
Bulletin
1 Jun.15/21
2 Jun.15/21
3 Jun.15/21
4 Jun.15/21
5 Jun.15/21
6 Jun.15/21
7 Jun.15/21
8 Jun.15/21
9 Jun.15/21
10 Jun.15/21
11 Jun.15/21
12 Jun.15/21
13 Jun.15/21
14 Jun.15/21
15 Jun.15/21
16 Jun.15/21
17 Jun.15/21
18 Jun.15/21
19 Jun.15/21
20 Jun.15/21
21 Jun.15/21
22 Jun.15/21
23 Jun.15/21
24 Jun.15/21
25 Jun.15/21
26 Jun.15/21
27 Jun.15/21
28 Jun.15/21
29 Jun.15/21
30 Jun.15/21
31 Jun.15/21
32 Jun.15/21
33 Jun.15/21
34 Jun.15/21
35 Jun.15/21
36 Jun.15/21
37 Jun.15/21
38 Jun.15/21
39 Jun.15/21
40 Jun.15/21
41 Jun.15/21
42 Jun.15/21
43 Jun.15/21
44 Jun.15/21
45 Jun.15/21
Printed in Great Britain
TRENT 1000 72−K570
Transmittal - Page 2

### Page 3

46 Jun.15/21
47 Jun.15/21
48 Jun.15/21
49 Jun.15/21
50 Jun.15/21
51 Jun.15/21
52 Jun.15/21
53 Jun.15/21
54 Jun.15/21
Supplement
1 Jun.15/21
Printed in Great Britain
TRENT 1000 72−K570
Transmittal - Page 3

### Page 4

1. Planning Information
A. Effectivity
Airbus A330
Trent 1000 Series Engines
TRENT7000-72 Engines prior to Serial No.75203 excluding 75199 to 75201.
TRENT7000-72C Engines prior to Serial No.75203 excluding 75199 to 75201.
TRENT7000, M32100963, M32101262, M32 Modules.
B. Concurrent Requirements
None.
C. Reason
(1) Problem
The current standard of Intermediate Pressure (IP) compressor stages 1 to
8 rotor shaft assembly is susceptible to high cycle fatigue cracking
travelling axially rearwards from the front edge of the front seal. This
cracking may result in reduced stage 1 disc integrity.
The problem is attributed to:
(a) Frequency alignment with the acoustic resonance of the cavity
downstream of the IP compressor front seal.
(b) Seal instability as a result of an acoustic bite from the interaction
with the acoustic resonance of the cavity downstream of the IP
compressor front seal.
(c) A feedback mechanism between the IP compressor front seal and buffer
seal involving the buffer seal exciting an inner cavity acoustic mode,
which successively excites the front seal.
(2) Evidence
The problem has been identified on a flight test development programme
engine with a maximum crack length of 8,34 mm (0.33 in.).
ENGINE - IP COMPRESSOR SHAFT - INTRODUCTION OF AN IP COMPRESSOR STAGES 1 TO 8 ROTOR
SHAFT ASSEMBLY FEATURING REVISED FRONT SEAL GEOMETRY - MOD.72-K570
Printed in Great Britain
TRENT 1000 72−K570
Page 1 of 54
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 5

In addition, the problem has been observed in-service and in the
development programme of other Rolls-Royce Trent series engines with a
similar design of IP compressor stages 1 to 8 rotor shaft assembly, with
maximum crack lengths ranging between 5,4 mm (0.21 in.) and 6,3 mm (0.25
in.).
(3) Substantiation
The changes introduced by this Service Bulletin have been the subject of
satisfactory engineering evaluation, including stress, vibration and
thermals analysis.
(4) Objective
Incorporation of this Service Bulletin (Modification) is designed to
maintain reliability.
(5) Effect of Bulletin on:
(a) Operation
Not affected.
(b) Maintenance
Not affected.
(c) Overhaul
Affected (see 1.L. Other Publications Affected).
(d) Repair Schemes
Affected (affected Repair Schemes will be revised to include the
part(s) introduced by this Service Bulletin).
(e) Interchangeability
Affected (see 1.M. Interchangeability of Parts).
D. Description
(1) The changes are:
(a) A revised IP compressor stages 1 to 8 rotor shaft assembly is
introduced similar to the existing item except for:
(i) The number of seal fins on the front seal is reduced from 4 to
3 resulting in the axial length of the seal arm to be reduced
by 9,05 mm (0.36 in.).
Printed in Great Britain
TRENT 1000 72−K570
Page 2
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 6

(ii) A chamfer is introduced on upper and lower front edges of the
front seal.
(2) Existing IP compressor stages 1 to 8 rotor shaft assemblies may be
reworked. The rework standard features identical changes as the new
production standard except for a radius feature on the upper front edge
that is a result of machining the part, and a machining tolerance of
plus/minus 0.3 mm (0.01 in.) is applied. Additionally, the upper and lower
front edges of the machined part are deburred.
(3) This Service Bulletin is in two parts as follows:
(a) Part 1
New production and in-service applications.
(b) Part 2
Application of a reworked standard of IP compressor stages 1 to 8
rotor shaft assembly.
(4) For effect on declared life see Time Limits Manual 05-10-01.
E. Compliance
(1) ON-WING
Not applicable.
(2) IN-SHOP
RECOMMENDED
It is recommended that this Service Bulletin be accomplished on
engines/powerplants at Module 32 Level 2 (Check and Repair and Hospital
Shop Visits) provided that the module is disassembled sufficiently to
expose the front face of the IP Compressor rotor assembly or Level 3
(Engine Refurbishment) or Level 4 (Engine Overhaul).
F. Approval
The technical content of Modification 72-K570 was approved by a representative
of the European Union Aviation Safety Agency (EASA) on May.20/21, EASA
certificate No. EASA.C.10076524.
The aircraft Type Certificate holder has been informed of this change.
Printed in Great Britain
TRENT 1000 72−K570
Page 3
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 7

G. Manpower
(1) On-wing
Not applicable.
(2) In-shop
12 man-hours - (Estimated)
NOTE: The parts affected by this Service Bulletin are accessible In-shop.
H. Material Price and Availability
Modification kit not required; parts supplied as single line items.
For prices and availability of future spares see supplement to this bulletin.
I. Tooling, Price and Availability
Special tools are required.
J. Weight and Balance
(1) Weight Change
Minus 0,36 kg (0.8 lb).
(2) Moment Arm
150 mm (5.9 in.) forwards.
(3) Datum
Power Plant Station (PPS) 3000 mm (118.11 in.).
K. References
Engine Manual, 72-32-30, Disassembly and Assembly
L. Other Publications Affected
(1) For effect on Illustrated Parts Catalogue (IPC) see 2. Material
Information.
(2) Cleaning/Inspection and Repair Manual, 72-32-31, Inspection/Check.
(3) Time Limits Manual, 05-10-01 and 05-20-01.
Printed in Great Britain
TRENT 1000 72−K570
Page 4
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 8

M. Interchangeability of Parts
Affected (see 2.D.(1) Instruction disposition codes).
Printed in Great Britain
TRENT 1000 72−K570
Page 5
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 9

2. Material Information
A. The kit required consists of the following parts:
None.
B. Parts to be reworked:
All Engines and Modules
P a r t2o fS B
72-32-31
FIG
ITEM
NO.
NEW
PART
NO. QTY PART TITLE
OLD
PART
NO.
INSTR
DISP
01 450 LV18447 1 SHAFT, ASSY-ROTOR, STAGES 1
T O8-I P COMP
KH18436 (1)
C. New production parts:
The following parts will be made available as future spares in addition to
those listed under B:
All Engines and Modules
P a r t1o fS B
72-32-31
FIG
ITEM
NO.
NEW
PART
NO. QTY PART TITLE
OLD
PART
NO.
INSTR
DISP
01 450 LV19601 1 SHAFT, ASSY-ROTOR, STAGES 1
T O8-I P COMP
KH18436 (1)
D. Instruction disposition codes:
(1) One-Way Interchangeable. The old part may be replaced by the old or new
part in isolation, but the new part must not be replaced by the old part
in isolation.
Printed in Great Britain
TRENT 1000 72−K570
Page 6
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 10

3. Accomplishment Instructions
A. The revised IP compressor stage 1 to 8 rotor shaft assembly introduced by this
Service Bulletin is one-way interchangeable (see 1.M. Interchangeability of
Parts). Remove the existing and install the new or reworked IP compressor stage
1 to 8 rotor shaft assembly in accordance with current overhaul procedures
(Engine Manual, 72-32-30, Disassembly and Assembly).
B. Rework the existing Intermediate Pressure (IP) Compressor Rotor Shaft Assembly
(KH18436) (IPC ATA 72-32-31, Fig/Item 01-450).
GENERAL DATA
CAUTION: THE IP COMPRESSOR ROTOR SHAFT MUST STAY CLEAN AND MUST HAVE NO
CONTAMINATION AT ALL TIMES. PUT ON CLEAN COTTON GLOVES BEFORE YOU TOUCH
THE SHAFT. WHEN THE PROCEDURE IS STOPPED OR COMPLETED, A COVER MUST BE
PUT ON THE SHAFT.
WARNING: MAKE SURE NECESSARY MASKING IS APPLIED, ELSE INJURY CAN OCCUR.
This TASK gives the procedure to modify the Intermediate Pressure (IP) Compressor
Rotor Shaft Assembly by machining the front seal arm.
Source demonstration is necessary for this rework. Only those companies who hold
letters of approval for this rework from Rolls-Royce plc are authorised to do
this rework. Vendors who hold this approval are listed in TSD 7019 (Authorised
Repair Vendor Directory). This source controlled rework and associated repair
vendor shop documentation are classified as fixed process documents and must be
controlled as specified in RRES90000.
Protect the part during Rework in between operations and after Rework in
accordance with OP TASK 70-00-00-300-340.
Overhaul Processes (OP) referenced in the text by TASK/SUBTASK number are
detailed in the Engine Overhaul Processes Manual (TSD594-J).
TASKS identified by SPM TASK are in the Standard Practices Manual.
This rework can be done by one of the below three parts:
Part 1: Rework with the Stages 1 and 2 blades removed, Stages 3 to 8 blades, IP
Compressor Front Stubshaft (KH54401) and Curvic (KH54407) installed.
Part 2: Rework in the piece part level.
Part 3: Rework with the Stages 1 to 8 blades, IP Compressor Front Stubshaft
(KH54401) and Curvic (KH54407) installed.
Equivalent locally manufactured tooling can be used. Agreement with Rolls-Royce
is necessary for the use of locally manufactured tooling.
Printed in Great Britain
TRENT 1000 72−K570
Page 7
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 11

Part 1 and Part 3 of this instruction require that no coolant is permitted to
ingress into the masked areas of the assembly. The vendor is to use an applicable
method to confirm that there is no ingress of coolant. The recommended method is
to apply litmus paper to the inside of the masked areas of the assembly.
With the agreement of Rolls-Royce, it is acceptable to change the build order of
the masking to apply shrink wrap before the polymer moulding tools and to apply
additional OMat 2/247 polyethylene tape or equivalent to get an improved seal, if
necessary.
Material of Component
Description RR Symbol Material
Intermediate Pressure (IP)
Compressor Rotor Shaft
Assembly
TJK Titanium Alloy
These rework instructions are controlled by RPR61137.
C. EQUIPMENT AND MATERIAL
(1) Standard Equipment
degreasing equipment
hand tools
heat gun
inspection equipment
locally made tooling
machining equipment
penetrant crack test equipment
swab etch equipment
suction equipment
vibration peen equipment
x3 to x7 magnification equipment
(2) Consumable Materials
OMat 2/101 lint free cloth
OMat 2/247 polyethylene tape
OMat 5/28 waterproof silicon carbide
OMat 652 fluorescent penetrant ultra-high sensitivity,
post-emulsified
OMat 1099 coolant, heavy duty concentrate
OMat 1284 polyethylene shrink wrap
NOTE: 1. To identify consumable materials, refer to the Overhaul
Materials Manual (OMat).
2. Additional consumable materials are included in the Overhaul
Processes referenced within this rework.
Printed in Great Britain
TRENT 1000 72−K570
Page 8
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 12

(3) Expendable Parts
FIG/ITEM PART NO PART IDENT QTY
None.
(4) Rework Parts
FIG/ITEM PART NO PART IDENT QTY
None.
(5) Special Tools
TOOL NUMBER TOOL DESCRIPTION QTY
RRT026842 dummy shaft
RRT081238 polymer stage 2-3 seal fin protector
RRT081239 polymer stage 1-2 seal fin protector
RRT081240 polymer stage 3-4 seal fin protector
RRT081241 polymer stage 4-5 seal fin protector
RRT081243 polymer stage 6-7 seal fin protector
RRT091632 polymer stage 5-6 seal fin protector
RRT091633 polymer stage 7-8 seal fin protector
RRT119750 lifter
RRT119751 lifting eye tool
RRT119752 top hat clamp
RRT119753 polymer top hat cover
RRT119755 polymer trough
RRT119756 dampening ring assembly
RRT119757 polymer front seal arm seal fin protector
RRT119758 polymer stage 1 dovetail protector
RRT119759 polymer stage 1 blade protector
RRT119760 polymer stage 2 dovetail protector
RRT119761 polymer stage 2 blade protector
RRT119762 polymer stage 3 blade protector
RRT119763 polymer stage 4 blade protector
RRT119764 polymer stage 5 blade protector
RRT119765 polymer stage 6 blade protector
RRT119766 polymer stage 7 blade protector
RRT119767 polymer stage 8 blade protector
RRT119768 polymer stage 8 seal fins protector
RRT086197 adapter
RRT119745 base plate
RRT119746 base plate nylon ring
RRT119748 shaft centraliser
Printed in Great Britain
TRENT 1000 72−K570
Page 9
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 13

D. Rework Instructions
(1) Part 1 - Disassemble the IP
Compressor Rotor Assembly.
Refer to Figure 1.
Refer to EM TASK 72-32-30-040-801.
Disassemble the IP Compressor Rotor
Assembly sufficiently to remove the
IP Compressor Stage 1 and 2 blades
only.
Do not remove the IP Compressor Front
Stubshaft and Curvic Ring. Do not
remove the Stages 3 through 8
Compressor Blades.
(2) Part 1 - Crack test the part. Do a fluorescent penetrant inspection
of the front seal arm.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
If a crack is found in the IP
Compressor Rotor Shaft then
quarantine the part and refer to
Rolls-Royce plc.
(3) Part 1 - Examine the part. Refer to Figure 1 and Figure 13.
Do a dimensional inspection of the
Dimension X. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
(4) Part 1 - Install the lifter to the
stubshaft.
Refer to Figure 14.
Refer to EM TASK 72-32-30-440-801.
Install the RRT119750 lifter to the
stubshaft. Engage the RRT086197
adapter to RRT119750 lifter and
attach the RRT086197 adapter to an
applicable hoist. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 10
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 14

(5) Part 1 - Install the part on the
base plate.
Refer to Figure 4, Figure 14 and
Figure 15.
Lift the assembly and place it on the
RRT119745 base plate. Make sure that
the location surfaces are clean
before placing it on the base plate.
Install the part on the RRT119745
base plate using RRT119746 base plate
nylon ring and the RRT119748 shaft
centraliser. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Remove the RRT086197 adapter and
RRT119750 lifter from the stubshaft.
Install the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser.
(6) Part 1 - Install the seal fin
protectors.
Refer to Figure 1, Figure 2 and
Figure 12.
Install the seal fin protectors. Use
RRT119768 polymer stage 8 seal fins
protector to protect the Stage 8 seal
fins. If necessary, use RRT081238
polymer stage 2-3 seal fin protector
and RRT081239 polymer stage 1-2 seal
fin protector to protect the Stage
2-3 and Stage 1-2 seal fins
respectively.
Connect the ends of protector with
the Velcro strap. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
(7) Part 1 - Protect the Stages 3 to 8
blades.
Refer to Figure 1, Figure 2 and
Figure 12.
Use RRT119762 polymer stage 3 blade
protector, RRT119763 polymer stage 4
blade protector, RRT119764 polymer
stage 5 blade protector, RRT119765
polymer stage 6 blade protector,
RRT119766 polymer stage 7 blade
protector and RRT119767 polymer stage
8 blade protector to protect the
Stages 3 to 8 blades. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 11
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 15

(8) Part 1 - Protect the Stages 1 to 2
dovetails.
Refer to Figure 1, Figure 2 and
Figure 12.
Use RRT119758 polymer stage 1
dovetail protector and RRT119760
polymer stage 2 dovetail protector to
protect the Stages 1 to 2 dovetails.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
(9) Part 1 - Protect the front seal
arm.
Refer to Figure 1, Figure 2 and
Figure 12.
Use RRT119757 polymer front seal arm
seal fin protector to protect the
three seal fins on the front seal
arm. Alternatively, equivalent
locally made tooling can be used with
the agreement of Rolls-Royce.
(10) Part 1 - Protect the Stubshaft. Refer to Figure 2 and Figure 3.
Install the RRT119755 polymer trough
adjacent to the Stage 1 disc and the
stubshaft. Alternatively, equivalent
locally made tooling can be used with
the agreement of Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 12
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 16

(11) Part 1 - Shrink wrap to cover the
rotor shaft.
CAUTION: YOU MUST NOT APPLY TOO MUCH
HEAT OR LET THE HEAT SOURCE
TO STAY AT THE SAME
LOCATION FOR TOO LONG. TO
CONTROL THE HEAT, KEEP THE
HEAT SOURCE AT A CORRECT
DISTANCE FROM THE SHRINK
WRAP. IF YOU DO NOT OBEY
THIS INSTRUCTION, DAMAGE TO
THE PROTECTORS OR COMPONENT
CAN OCCUR.
Refer to Figure 3 and Figure 4.
Wind OMat 1284 polyethylene shrink
wrap to cover the part as below:
Shrink wrap from the Stage 3 blade to
Stage 8 seal fin protector 3 times.
Shrink wrap from the Stage 1 seal fin
protector to Stage 2 dovetail 3
times. Shrink wrap from the Stage 1
seal fin protector to Stage 8 seal
fin protector once.
Make sure to get a final wrap
thickness of 1,20 mm (0.047 in.)
minimum (before shrink). If not,
apply additional shrink wrap.
Ensure that shrink wrap is
sufficiently overlapped from Stages 1
to 8. Consider heat shrinkage of
shrink wrap during the overlap
process. Use OMat 2/247 polyethylene
tape to hold the OMat 1284
polyethylene shrink wrap in position.
Use a heat gun to heat and shrink
OMat 1284 polyethylene shrink wrap.
Set the heat gun to the minimum
temperature necessary to shrink the
polyethylene shrink wrap. Refer to
manufacturer's instructions for the
maximum temperature.
Equivalent consumables to OMat 2/247
and OMat 1284 can be used with
agreement of Rolls-Royce.
Visually inspect the polyethylene
shrink wrap for the signs of
overheating, heat damage and holes.
If overheated, damage or holes are
evident, then remove and replace the
shrink wrap. Alternatively,
equivalent locally made tooling and
masking methods can be used with the
agreement of Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 13
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 17

(12) Part 1 - Install the part on the
machining equipment.
Refer to Figure 4 and Figure 15.
Install the RRT119751 lifting eye
tool on the RRT119748 shaft
centraliser of the base plate. Attach
an applicable hoist to the RRT119751
lifting eye tool and place it on the
machining equipment. Use the clocking
ring on the tooling base plate to set
the tooling and component assembly to
run true.
Remove the RRT119751 lifting eye tool
from the RRT119748 shaft centraliser.
(13) Part 1 - Install the top hat clamp
and polymer top hat cover.
Refer to Figure 4 and Figure 15.
Install the RRT119752 top hat clamp
on the RRT119748 shaft centraliser.
Install the RRT119753 polymer top hat
cover onto the RRT119752 top hat
clamp using washer and nut.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce. Make sure
the clamping force does not distort
the top hat cover.
Printed in Great Britain
TRENT 1000 72−K570
Page 14
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 18

(14) Part 1 - Machine the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
CAUTION: DO NOT USE THE ROUGH
MACHINING PARAMETERS FOR
MATERIAL REMOVAL AT A
DIMENSION OF NOT LESS THAN
1,00 MM (0.039 IN.) FROM
THE FINAL FINISHED SURFACE
AS IT WILL MAKE THIS PART
UNSERVICEABLE.
Refer to Figure 1 and Figure 13.
Machine the front seal arm from the
front edge of the seal arm. Burrs and
sharp edges can be removed by
machining, if necessary.
Refer to approved vendor techniques.
The machining parameters used must
not be changed without revalidation
and agreement of Rolls Royce Plc.
MACHINING DATA
NOTE: New insert must be used for roughing, semi-finishing and
finishing operations each time the rework is done.
A. Roughing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,25 to 1,00 mm (0.010 to 0.039
in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Printed in Great Britain
TRENT 1000 72−K570
Page 15
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 19

Coolant OMat 1099 coolant, heavy duty
concentrate
B. Semi-finishing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
C. Finishing
Surface speed 18,90 to 23,10 m/min (744 to 909
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
(15) Part 1 - Remove all coolant from
the part.
Dry the rework area. Use OMat 2/101
lint free cloth. Use suction
equipment.
Printed in Great Britain
TRENT 1000 72−K570
Page 16
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 20

(16) Part 1 - Dress the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
Dress the part to remove burrs and
sharp edges.
Use OMat 5/28 waterproof silicon
carbide or equivalent.
(17) Part 1 - Remove the part. Remove the RRT119753 polymer top hat
cover and RRT119752 top hat clamp.
Attach the RRT119751 lifting eye tool
to the RRT119748 shaft centraliser.
Use an applicable hoist to lift the
part.
Lift the part from the machining
equipment with the base plate.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
Remove the RRT119751 lifting eye tool
from the RRT119748 shaft centraliser
(18) Part 1 - Clean the rework area. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102. Swab
degrease the rework area.
Use degreasing equipment.
Printed in Great Britain
TRENT 1000 72−K570
Page 17
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 21

(19) Part 1 - Examine the part. Refer to Figure 1 and Figure 13.
Do a visual and dimensional
inspection of the reworked area.
Make sure that all the burrs and
sharp edges have been removed. Reject
if not satisfactory.
Do a visual inspection for damage
like scratches, scores and nicks:
Accept damage if up to 0,013 mm
(0.0005 in.) in depth and not more
than 25,40 mm (1.000 in.) in length.
Reject damage if more than 0,013 mm
(0.0005 in.) in depth or more than
25,40 mm (1.000 in.) in length.
(20) Part 1 - Etch the part. Do a swab etch on the rework area.
Refer to OP TASK 70-00-00-100-148,
SUBTASK 70-00-00-110-148-001.
Use swab etch equipment.
(21) DELETED.
(22) Part 1 - Crack test the part. Do a fluorescent penetrant inspection
of the rework area.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
Reject if cracked.
(23) Part 1 - Clean the part. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102. Swab
degrease the rework area.
Use degreasing equipment.
(24) Part 1 - Remove the masking. CAUTION: MAKE SURE THAT THE ROTOR
ASSEMBLY, SEAL FINS AND
DOVETAILS ARE NOT DAMAGED
DURING REMOVAL OF THE
MASKING AND PROTECTORS.
Remove all the shrink wrap, covers
and protectors from the IP Compressor
Rotor Shaft Assembly installed from
Step 6 to Step 11.
Use hand tools.
Printed in Great Britain
TRENT 1000 72−K570
Page 18
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 22

(25) Part 1 - Install the lifter to the
stubshaft.
Refer to Figure 14.
Refer to EM TASK 72-32-30-440-801.
Remove the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser. Install the RRT119750
lifter to the stubshaft. Engage the
RRT086197 adapter to the RRT119750
lifter and attach the RRT086197
adapter to an applicable hoist.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
(26) Part 1 - Remove the Rotor Assembly
from the base plate.
Lift the Rotor Assembly from the
RRT119745 base plate using RRT119750
lifter and an applicable hoist. Place
the Rotor Assembly on a pallet.
Remove the RRT086197 adapter and the
RRT119750 lifter from the stubshaft.
(27) Part 1 - Examine the part. Refer to Figure 1 and Figure 13.
Do a visual inspection of the part.
Make sure there is no handling
damage. Reject if damaged.
Use an applicable inspection method
to make sure there is no coolant
ingress. Reject if any evidence of
coolant ingress is found.
Do a dimensional inspection of the
part. Make sure the maximum machining
length is not more than the rework
limit.
Do a dimensional inspection of the
Dimension Y. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
Reject, if not in the limits.
(28) Part 1 - Identify the part. Refer to Figure 16.
Refer to OP TASK 70-00-00-300-363.
Strike through the existing part
number KH18436. Vibration peen
LV18447 in the area identified.
Use vibration peen equipment.
Remove burrs and raised material
produced by vibration peening. Use
OMat 5/28 waterproof silicon carbide
or equivalent.
Printed in Great Britain
TRENT 1000 72−K570
Page 19
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 23

(29) Part 1 - Assemble the parts. Re-assemble the parts as per EM TASK
72-32-30-440-801.
Make sure that part is balanced as
per EM TASK 72-32-30-440-801.
(1) Part 2 - Disassemble the IP
Compressor Rotor Assembly (if
necessary).
Refer to Figure 5.
Refer to EM TASK 72-32-30-040-801.
Disassemble the IP Compressor Rotor
Assembly. Remove the IP Compressor
Stages 1 to 8 blades, Curvic Ring and
the Front Stubshaft.
(2) Part 2 - Crack test the part. Do a fluorescent penetrant inspection
of the front seal arm.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
If a crack is found in the IP
Compressor Rotor Shaft then
quarantine the part and refer to
Rolls-Royce plc.
(3) Part 2 - Examine the part. Refer to Figure 5 and Figure 13.
Do a dimensional inspection of the
Dimension X. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
(4) Part 2 - Install the dummy
stubshaft.
Refer to Figure 7.
Install RRT026842 dummy shaft to the
IP Compressor Rotor Shaft.
Refer to EM TASK 72-32-30-440-801.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
(5) Part 2 - Install the lifter to the
dummy stubshaft.
Refer to Figure 14.
Refer to EM TASK 72-32-30-440-801.
Install the RRT119750 lifter to the
dummy stubshaft. Engage the RRT086197
adapter to RRT119750 lifter and
attach the RRT086197 adapter to an
applicable hoist. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 20
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 24

(6) Part 2 - Install the part on the
base plate.
Refer to Figure 7, Figure 14 and
Figure 15.
Lift the assembly and place it on the
RRT119745 base plate. Make sure that
the location surfaces are clean
before placing it on the base plate.
Install the part on the RRT119745
base plate using RRT119746 base plate
nylon ring and the RRT119748 shaft
centraliser. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Remove the RRT086197 adapter and
RRT119750 lifter from the stubshaft.
Install the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser.
(7) Part 2 - Install the seal fin
protectors.
Refer to Figure 5, Figure 6 and
Figure 12.
Install the seal fin protectors. Use
RRT119768 polymer stage 8 seal fins
protector to protect the Stage 8 seal
fins. Use RRT091633 polymer stage 7-8
seal fin protector, RRT081243 polymer
stage 6-7 seal fin protector,
RRT091632 polymer stage 5-6 seal fin
protector, RRT081241 polymer stage
4-5 seal fin protector, RRT081240
polymer stage 3-4 seal fin protector,
RRT081238 polymer stage 2-3 seal fin
protector and RRT081239 polymer stage
1-2 seal fin protector to protect the
Stage 7-8, Stage 6-7, Stage 5-6,
Stage 4-5, Stage 3-4, Stage 2-3 and
Stage 1-2 seal fins respectively.
Connect the ends of protector with
the Velcro strap. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 21
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 25

(8) Part 2 - Protect the Stages 1 to 2
dovetails.
Refer to Figure 5, Figure 6 and
Figure 12.
Use RRT119758 polymer stage 1
dovetail protector and RRT119760
polymer stage 2 dovetail protector to
protect the Stages 1 to 2 dovetails.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
(9) Part 2 - Protect the front seal
arm.
Refer to Figure 5, Figure 6 and
Figure 12.
Use RRT119757 polymer front seal arm
seal fin protector to protect the
three seal fins on the front seal
arm. Alternatively, equivalent
locally made tooling can be used with
the agreement of Rolls-Royce.
(10) Part 2 - Install the part on the
machining equipment.
Refer to Figure 7 and Figure 15.
Install the RRT119751 lifting eye
tool on the RRT119748 shaft
centraliser of the base plate. Attach
an applicable hoist to the RRT119751
lifting eye tool and place it on the
machining equipment. Use the clocking
ring on the tooling base plate to set
the tooling and component assembly to
run true.
Remove the RRT119751 lifting eye tool
from the RRT119748 shaft centraliser.
Printed in Great Britain
TRENT 1000 72−K570
Page 22
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 26

(11) Part 2 - Machine the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
CAUTION: DO NOT USE THE ROUGH
MACHINING PARAMETERS FOR
MATERIAL REMOVAL AT A
DIMENSION OF NOT LESS THAN
1,00 MM (0.039 IN.) FROM
THE FINAL FINISHED SURFACE
AS IT WILL MAKE THIS PART
UNSERVICEABLE.
Refer to Figure 5 and Figure 13.
Machine the front seal arm from the
front edge of the seal arm. Burrs and
sharp edges can be removed by
machining, if necessary.
Refer to approved vendor techniques.
The machining parameters used must
not be changed without revalidation
and agreement of Rolls Royce Plc.
MACHINING DATA
NOTE: New insert must be used for roughing, semi-finishing and
finishing operations each time the rework is done.
A. Roughing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,25 to 1,00 mm (0.010 to 0.039
in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Printed in Great Britain
TRENT 1000 72−K570
Page 23
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 27

Coolant OMat 1099 coolant, heavy duty
concentrate
B. Semi-finishing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
C. Finishing
Surface speed 18,90 to 23,10 m/min (744 to 909
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
(12) Part 2 - Remove all coolant from
the part.
Dry the rework area. Use OMat 2/101
lint free cloth. Use suction
equipment.
Printed in Great Britain
TRENT 1000 72−K570
Page 24
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 28

(13) Part 2 - Dress the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
Dress the part to remove burrs and
sharp edges.
Use OMat 5/28 waterproof silicon
carbide or equivalent.
(14) Part 2 - Remove the part. Attach the RRT119751 lifting eye tool
to the RRT119748 shaft centraliser.
Use an applicable hoist to lift the
part.
Lift the part from the machining
equipment with the base plate.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
Remove the RRT119751 lifting eye tool
from the RRT119748 shaft centraliser
(15) Part 2 - Remove the part from the
base plate.
Refer to Figure 7.
Refer to EM TASK 72-32-30-440-801.
Remove the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser. Install the RRT119750
lifter to dummy stubshaft. Engage the
RRT086197 adapter to RRT119750 lifter
and attach RRT086197 adapter to an
applicable hoist. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Use an applicable hoist to lift the
part from the base plate.
Printed in Great Britain
TRENT 1000 72−K570
Page 25
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 29

(16) Part 2 - Remove the dummy
stubshaft.
Remove the dummy stubshaft RRT026842
installed in the Step 3. Refer to EM
TASK 72-32-30-040-801.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
(17) Part 2 - Remove the masking. CAUTION: MAKE SURE THAT THE ROTOR
ASSEMBLY, SEAL FINS AND
DOVETAILS ARE NOT DAMAGED
DURING REMOVAL OF THE
MASKING AND PROTECTORS.
Remove all the seal fin protectors
and dovetail protectors from the IP
Compressor Rotor Shaft Assembly
installed from Step 7 to Step 9.
Use hand tools.
(18) Part 2 - Clean the part. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102.
Refer to the approved vendor method.
Use degreasing equipment.
(19) Part 2 - Examine the part. Refer to Figure 5 and Figure 13.
Do a visual and dimensional
inspection of the reworked area.
Make sure that all the burrs and
sharp edges have been removed. Reject
if not satisfactory.
Do a visual inspection for damage
like scratches, scores and nicks:
Accept damage if up to 0,013 mm
(0.0005 in.) in depth and not more
than 25,40 mm (1.000 in.) in length.
Reject damage if more than 0,013 mm
(0.0005 in.) in depth or more than
25,40 mm (1.000 in.) in length.
(20) Part 2 - Etch the part. Do a swab etch on the rework area.
Refer to OP TASK 70-00-00-100-148,
SUBTASK 70-00-00-110-148-001.
Use swab etch equipment.
(21) DELETED.
Printed in Great Britain
TRENT 1000 72−K570
Page 26
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 30

(22) Part 2 - Crack test the part. Do a fluorescent penetrant inspection
of the rework area.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
Reject if cracked.
(23) Part 2 - Clean the rework area. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102. Swab
degrease the rework area.
Use degreasing equipment.
(24) Part 2 - Examine the part. Refer to Figure 5 and Figure 13.
Do a visual inspection of the part.
Make sure there is no handling
damage. Reject if damaged.
Do a dimensional inspection of the
part. Make sure the maximum machining
length is not more than the rework
limit.
Do a dimensional inspection of the
Dimension Y. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
Reject, if not in the limits.
(25) Part 2 - Identify the part. Refer to Figure 16.
Refer to OP TASK 70-00-00-300-363.
Strike through the existing part
number KH18436. Vibration peen
LV18447 in the area identified.
Use vibration peen equipment.
Remove burrs and raised material
produced by vibration peening. Use
OMat 5/28 waterproof silicon carbide
or equivalent.
(26) Part 2 - Assemble the parts (if
necessary).
Re-install the Stages 1 to 8 Blades,
Curvic Ring and the Stubshaft on the
IPC Rotor as per EM TASK
72-32-30-440-801.
Make sure that part is balanced as
per EM TASK 72-32-30-440-801.
Printed in Great Britain
TRENT 1000 72−K570
Page 27
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 31

(1) Part 3 - Disassemble the IP
Compressor Rotor Assembly.
Refer to Figure 8.
Refer to EM TASK 72-32-30-040-801.
Disassemble the IP Compressor Rotor
Assembly.
Do not remove the IP Compressor Front
Stubshaft and Curvic Ring. Do not
remove the Stages 1 through 8
Compressor Blades.
(2) Part 3 - Crack test the part. Do a fluorescent penetrant inspection
of the front seal arm.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
If a crack is found in the IP
Compressor Rotor Shaft then
quarantine the part and refer to
Rolls-Royce plc.
(3) Part 3 - Examine the part. Refer to Figure 8 and Figure 13.
Do a dimensional inspection of the
Dimension X. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
(4) Part 3 - Install the lifter to the
stubshaft.
Refer to Figure 14.
Refer to EM TASK 72-32-30-440-801.
Install the RRT119750 lifter to the
stubshaft. Engage the RRT086197
adapter to RRT119750 lifter and
attach the RRT086197 adapter to an
applicable hoist. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 28
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 32

(5) Part 3 - Install the part on the
base plate.
Refer to Figure 11, Figure 14 and
Figure 15.
Lift the assembly and place it on the
RRT119745 base plate. Make sure that
the location surfaces are clean
before placing it on the base plate.
Install the part on the RRT119745
base plate using RRT119746 base plate
nylon ring and the RRT119748 shaft
centraliser. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
Remove the RRT086197 adapter and
RRT119750 lifter from the stubshaft.
Install the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser.
(6) Part 3 - Install the seal fin
protectors.
Refer to Figure 8, Figure 9 and
Figure 12.
Install the seal fin protectors. Use
RRT119768 polymer stage 8 seal fins
protector to protect the Stage 8 seal
fins.
Connect the ends of protector with
the Velcro strap. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
(7) Part 3 - Protect the Stages 1 to 8
blades.
Refer to Figure 8, Figure 9 and
Figure 12.
Use RRT119759 polymer stage 1 blade
protector, RRT119761 polymer stage 2
blade protector, RRT119762 polymer
stage 3 blade protector, RRT119763
polymer stage 4 blade protector,
RRT119764 polymer stage 5 blade
protector, RRT119765 polymer stage 6
blade protector, RRT119766 polymer
stage 7 blade protector and RRT119767
polymer stage 8 blade protector to
protect the Stages 1 to 8 blades.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 29
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 33

(8) Part 3 - Protect the front seal
arm.
Refer to Figure 8, Figure 9 and
Figure 12.
Use RRT119757 polymer front seal arm
seal fin protector to protect the
three seal fins on the front seal
arm. Alternatively, equivalent
locally made tooling can be used with
the agreement of Rolls-Royce.
(9) Part 3 - Protect the Stubshaft. Refer to Figure 9 and Figure 10.
Install the RRT119755 polymer trough
adjacent to the Stage 1 disc and the
stubshaft. Alternatively, equivalent
locally made tooling can be used with
the agreement of Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 30
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 34

(10) Part 3 - Shrink wrap to cover the
rotor shaft.
CAUTION: YOU MUST NOT APPLY TOO MUCH
HEAT OR LET THE HEAT SOURCE
TO STAY AT THE SAME
LOCATION FOR TOO LONG. TO
CONTROL THE HEAT, KEEP THE
HEAT SOURCE AT A CORRECT
DISTANCE FROM THE SHRINK
WRAP. IF YOU DO NOT OBEY
THIS INSTRUCTION, DAMAGE TO
THE PROTECTORS OR COMPONENT
CAN OCCUR.
Refer to Figure 10 and Figure 11.
Wind OMat 1284 polyethylene shrink
wrap to cover from the Stage 1 seal
fin protector to Stage 8 seal fin
protector 4 times. Make sure to get a
final wrap thickness of 1,20 mm
(0.047 in.) minimum (before shrink).
If not, apply additional shrink wrap.
Consider heat shrinkage of shrink
wrap during the overlap process. Use
OMat 2/247 polyethylene tape to hold
the OMat 1284 polyethylene shrink
wrap in position.
Use a heat gun to heat and shrink
OMat 1284 polyethylene shrink wrap.
Set the heat gun to the minimum
temperature necessary to shrink the
polyethylene shrink wrap. Refer to
manufacturer's instructions for the
maximum temperature.
Equivalent consumables to OMat 2/247
and OMat 1284 can be used with the
agreement of Rolls-Royce.
Visually inspect the polyethylene
shrink wrap for the signs of
overheating, heat damage and holes.
If overheated, damage or holes are
evident, then remove and replace the
shrink wrap. Alternatively,
equivalent locally made tooling and
masking methods can be used with the
agreement of Rolls-Royce.
Printed in Great Britain
TRENT 1000 72−K570
Page 31
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 35

(11) Part 3 - Install the part on the
machining equipment.
Refer to Figure 11 and Figure 15.
Install the RRT119751 lifting eye
tool on the RRT119748 shaft
centraliser of the base plate. Attach
an applicable hoist to the RRT119751
lifting eye tool and place it on the
machining equipment. Use the clocking
ring on the tooling base plate to set
the tooling and component assembly to
run true.
Remove the RRT119751 lifting eye tool
from the RRT119748 shaft centraliser.
(12) Part 3 - Install the top hat clamp
and top hat cover.
Refer to Figure 11 and Figure 15.
Install the RRT119752 top hat clamp
on the RRT119748 shaft centraliser.
Install the RRT119753 polymer top hat
cover onto the RRT119752 top hat
clamp using washer and nut.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce. Make sure
the clamping force does not distort
the top hat cover.
Printed in Great Britain
TRENT 1000 72−K570
Page 32
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 36

(13) Part 3 - Machine the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
CAUTION: DO NOT USE THE ROUGH
MACHINING PARAMETERS FOR
MATERIAL REMOVAL AT A
DIMENSION OF NOT LESS THAN
1,00 MM (0.039 IN.) FROM
THE FINAL FINISHED SURFACE
AS IT WILL MAKE THIS PART
UNSERVICEABLE.
Refer to Figure 8 and Figure 13.
Machine the front seal arm from the
front edge of the seal arm. Burrs and
sharp edges can be removed by
machining, if necessary.
Refer to approved vendor techniques.
The machining parameters used must
not be changed without revalidation
and agreement of Rolls Royce Plc.
MACHINING DATA
NOTE: New insert must be used for roughing, semi-finishing and
finishing operations each time the rework is done.
A. Roughing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,25 to 1,00 mm (0.010 to 0.039
in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Printed in Great Britain
TRENT 1000 72−K570
Page 33
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 37

Coolant OMat 1099 coolant, heavy duty
concentrate
B. Semi-finishing
Surface speed 31,50 to 38,50 m/min (1240 to 1515
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
C. Finishing
Surface speed 18,90 to 23,10 m/min (744 to 909
in./min)
Feed Rate 0,09 to 0,11 mm/rev (0.003 to
0.004 in./rev)
Depth of Cut 0,225 to 0,275 mm (0.0089 to
0.0108 in.)
Tool Grade H13A Insert, tip radius 0,80
mm (0.032 in.)
Coolant OMat 1099 coolant, heavy duty
concentrate
(14) Part 3 - Remove all coolant from
the part.
Dry the rework area. Use OMat 2/101
lint free cloth. Use suction
equipment.
Printed in Great Britain
TRENT 1000 72−K570
Page 34
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 38

(15) Part 3 - Dress the part. CAUTION: TITANIUM COMPONENTS:
WHEELS, STONES, ABRASIVE
PAPERS USED FOR DRESSING,
BLENDING OR POLISHING MUST
BE OF THE SILICON CARBIDE
TYPE. ALUMINIUM OXIDE TYPES
MUST NOT BE USED. IF
MECHANICAL CUTTERS ARE
USED, ONLY LIGHT CUTS MUST
BE MADE TO AVOID
OVERHEATING THE MATERIAL.
IF, DURING DRESSING,
BLENDING OR POLISHING, THE
MATERIAL IS DISCOLOURED DUE
TO HEATING, DARKER THAN A
LIGHT STRAW COLOUR, THE
COMPONENT MUST BE REJECTED.
Dress the part to remove burrs and
sharp edges.
Use OMat 5/28 waterproof silicon
carbide or equivalent.
(16) Part 3 - Remove the part. Remove the RRT119753 polymer top hat
cover and RRT119752 top hat clamp.
Attach the RRT119751 lifting eye
tool to the RRT119748 shaft
centraliser. Use an applicable hoist
to lift the part.
Lift the part from the machining
equipment with the base plate.
Alternatively, equivalent locally
made tooling can be used with the
agreement of Rolls-Royce.
Remove the RRT119751 lifting eye
tool from the RRT119748 shaft
centraliser.
(17) Part 3 - Clean the rework area. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102. Swab
degrease the rework area.
Use degreasing equipment.
Printed in Great Britain
TRENT 1000 72−K570
Page 35
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 39

(18) Part 3 - Examine the part. Refer to Figure 8 and Figure 13.
Do a visual and dimensional
inspection of the reworked area.
Make sure that all the burrs and
sharp edges have been removed. Reject
if not satisfactory.
Do a visual inspection for damage
like scratches, scores and nicks:
Accept damage if up to 0,013 mm
(0.0005 in.) in depth and not more
than 25,40 mm (1.000 in.) in length.
Reject damage if more than 0,013 mm
(0.0005 in.) in depth or more than
25,40 mm (1.000 in.) in length.
(19) Part 3 - Etch the part. Do a swab etch on the rework area.
Refer to OP TASK 70-00-00-100-148,
SUBTASK 70-00-00-110-148-001.
Use swab etch equipment.
(20) DELETED.
(21) Part 3 - Crack test the part. Do a fluorescent penetrant inspection
of the rework area.
Refer to OP TASK 70-00-00-200-210.
Use OMat 652 fluorescent penetrant
ultra-high sensitivity,
post-emulsified and penetrant crack
test equipment.
Reject if cracked.
(22) Part 3 - Clean the part. Refer to OP TASK 70-00-00-100-101 or
OP TASK 70-00-00-100-102. Swab
degrease the rework area.
Use degreasing equipment.
(23) Part 3 - Remove the masking. CAUTION: MAKE SURE THAT THE ROTOR
ASSEMBLY, SEAL FINS AND
DOVETAILS ARE NOT DAMAGED
DURING REMOVAL OF THE
MASKING AND PROTECTORS.
Remove all the shrink wrap, covers
and protectors from the IP Compressor
Rotor Shaft Assembly installed from
Step 6 to Step 10.
Use hand tools.
Printed in Great Britain
TRENT 1000 72−K570
Page 36
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 40

(24) Part 3 - Install the lifter to the
stubshaft.
Refer to Figure 14.
Refer to EM TASK 72-32-30-440-801.
Remove the RRT119756 dampening ring
assembly on the RRT119748 shaft
centraliser. Install the RRT119750
lifter to the stubshaft. Engage the
RRT086197 adapter to RRT119750 lifter
and attach the RRT086197 adapter to
an applicable hoist. Alternatively,
equivalent locally made tooling can
be used with the agreement of
Rolls-Royce.
(25) Part 3 - Remove the Rotor Assembly
from the base plate.
Lift the Rotor Assembly from the
RRT119745 base plate using RRT119750
lifter and an applicable hoist. Place
the Rotor Assembly on a pallet.
Remove the RRT086197 adapter and the
RRT119750 lifter from the stubshaft.
(26) Part 3 - Examine the part. Refer to Figure 8 and Figure 13.
Do a visual inspection of the part.
Make sure there is no handling
damage. Reject if damaged.
Use an applicable inspection method
to make sure there is no coolant
ingress. Reject if any evidence of
coolant ingress is found.
Do a dimensional inspection of the
part. Make sure the maximum machining
length is not more than the rework
limit.
Do a dimensional inspection of the
Dimension Y. Record the dimension in
the Engine log book against the
serial number of the part. Record the
measurement to 2 decimal places in
metric and 3 decimal places in
imperial.
Reject, if not in the limits.
Printed in Great Britain
TRENT 1000 72−K570
Page 37
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 41

(27) Part 3 - Identify the part. Refer to Figure 16.
Refer to OP TASK 70-00-00-300-363.
Strike through the existing part
number KH18436. Vibration peen
LV18447 in the area identified.
Use vibration peen equipment.
Remove burrs and raised material
produced by vibration peening. Use
OMat 5/28 waterproof silicon carbide
or equivalent.
If necessary, it is acceptable to
record the service bulletin
accomplishment and new LV18447 part
number in the engine log book. The
new LV18447 part number must be
permanently marked on the part and
the existing KH18436 part number
struck through at the next engine
overhaul of the IPC module.
(28) Part 3 - Assemble the parts. Re-assemble the parts as per EM TASK
72-32-30-440-801.
Make sure that part is balanced as
per EM TASK 72-32-30-440-801.
E. A record of accomplishment is required.
The Service Bulletin number and relevant Service Bulletin part(s) shall be
recorded in the relevant log book when the modification part is fitted in its
entirety.
Printed in Great Britain
TRENT 1000 72−K570
Page 38
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 42

dem0002676
FRONT SEAL ARM
STAGE 8 BLADE
STAGE 7 BLADE
STAGE 6 BLADE
STAGE 5 BLADE
STAGE 4 BLADE
STAGE 3 BLADE
B
(ø480,46 (18,916))
IP COMPRESSOR
FRONT STUB SHAFT ASSEMBLY
72−32−31
01−350
A
STAGE 8 DISC
IP COMPRESSOR
ROTOR SHAFT 
72−32−31
01−450 STAGE 7 DISC
STAGE 6 DISC
STAGE 5 DISC
STAGE 4 DISC
STAGE 3 DISC
STAGE 2 DISC
STAGE 1 DISC
IP COMPRESSOR
CURVIC RING
72−32−31
01−125
AA
DIMENSIONS ARE IN MILLIMETERS (INCHES)
THE SURFACE TEXTURE VALUES ARE IN MICROMETERS (MICROINCHES)
THE SURFACE TEXTURE TO BE 1,6 (63) UNLESS SPECIFIED DIFFERENTLY
GEOMETRIC SYMBOLS ARE GIVEN IN THE ISO MANUAL R1101
REMOVE THE SHARP EDGES 0,10 TO 0,50 (0.004 TO 0.020)
MACHINE WHERE SHOWN 
SECTION THROUGH THE IP COMPRESSOR 
STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY 
C
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
General section view (Part 1)
Figure 1
Printed in Great Britain
TRENT 1000 72−K570
Page 39
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 43

dem0002679
STAGE 2−3
SEAL FINS
RRT119768
PROTECTOR
STAGE 3−4
SEAL FINS
STAGE 4−5
SEAL FINS
STAGE 5−6
SEAL FINS
STAGE 7−8
SEAL FINS
STAGE 8
SEAL FINS
STAGE 6−7
SEAL FINS
STAGE 1−2
SEAL FINS
PROTECTOR
TO COVER THE
3 SEAL FINS AB
SECTION THROUGH THE IP COMPRESSOR
 STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
TO SHOW THE SEAL FINS PROTECTOR DETAILS
RRT119757
RRT081239
PROTECTOR
(OPTIONAL)
RRT081238
PROTECTOR
(OPTIONAL)
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
PROTECTOR
RRT119758
PROTECTOR
RRT119760
PROTECTOR
RRT119762
PROTECTOR
RRT119763 PROTECTOR
RRT119764
PROTECTOR
RRT119765
PROTECTOR
RRT119766
PROTECTOR
RRT119767
Protector details (Part 1)
Figure 2
Printed in Great Britain
TRENT 1000 72−K570
Page 40
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 44

dem0002682
POLYETHYLENE 
SHRINK WRAP
RRT119755
POLYMER TROUGH
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
Shrink wrap details (Part 1)
Figure 3
Printed in Great Britain
TRENT 1000 72−K570
Page 41
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 45

POLYETHYLENE
SHRINK WRAP
dem0002687 REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
RRT119753
POLYMER TOP HAT COVER RRT119748SHAFT CENTRALISER
RRT119745
BASE PLATE
POLYMER
PROTECTORS
Part arrangement on base plate (Part 1)
Figure 4
Printed in Great Britain
TRENT 1000 72−K570
Page 42
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 46

dem0002677
FRONT SEAL ARM
B
(ø480,46 (18,916))
A
STAGE 8 DISC
IP COMPRESSOR
ROTOR SHAFT 
72−32−31
01−450 STAGE 7 DISC
STAGE 6 DISC
STAGE 5 DISC
STAGE 4 DISC
STAGE 3 DISC
STAGE 2 DISC
STAGE 1 DISC
AA
DIMENSIONS ARE IN MILLIMETERS (INCHES)
THE SURFACE TEXTURE VALUES ARE IN MICROMETERS (MICROINCHES)
THE SURFACE TEXTURE TO BE 1,6 (63) UNLESS SPECIFIED DIFFERENTLY
GEOMETRIC SYMBOLS ARE GIVEN IN THE ISO MANUAL R1101
REMOVE THE SHARP EDGES 0,10 TO 0,50 (0.004 TO 0.020)
MACHINE WHERE SHOWN 
SECTION THROUGH THE IP COMPRESSOR 
STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY 
C
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
General section view (Part 2)
Figure 5
Printed in Great Britain
TRENT 1000 72−K570
Page 43
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 47

dem0002680
RRT081239
PROTECTOR
STAGE 2−3
SEAL FINS
RRT081238
PROTECTOR
RRT081240
PROTECTOR
RRT081241
PROTECTOR
RRT091632
PROTECTOR
RRT081243
PROTECTOR
RRT091633
PROTECTOR
RRT119768
PROTECTOR
STAGE 3−4
SEAL FINS
STAGE 4−5
SEAL FINS
STAGE 5−6
SEAL FINS
STAGE 7−8
SEAL FINS
STAGE 8
SEAL FINS
STAGE 6−7
SEAL FINS
STAGE 1−2
SEAL FINS
PROTECTOR
TO COVER THE
3 SEAL FINS AB
SECTION THROUGH THE IP COMPRESSOR
 STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
TO SHOW THE SEAL FINS PROTECTOR DETAILS
RRT119757
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
RRT119758
PROTECTOR
RRT119760
PROTECTOR
Protector details (Part 2)
Figure 6
Printed in Great Britain
TRENT 1000 72−K570
Page 44
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 48

THE STUB SHAFT IS SHOWN ONLY FOR DEPICTION PURPOSES
dem0002688 REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
RRT119745
BASE PLATE
RRT119748
SHAFT CENTRALISER
DUMMY STUBSHAFT
RRT026842
Part arrangement on base plate (Part 2)
Figure 7
Printed in Great Britain
TRENT 1000 72−K570
Page 45
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 49

dem0002678
FRONT SEAL ARM
STAGE 8 BLADE
STAGE 7 BLADE
STAGE 6 BLADE
STAGE 5 BLADE
STAGE 3 BLADE
B
(ø480,46 (18,916))
A
STAGE 8 DISC
IP COMPRESSOR
ROTOR SHAFT 
72−32−31
01−450 STAGE 7 DISC
STAGE 6 DISC
STAGE 5 DISC
STAGE 4 DISC
STAGE 3 DISC
STAGE 2 DISC
STAGE 1 DISC
IP COMPRESSOR
CURVIC RING
72−32−31
01−125
AA
DIMENSIONS ARE IN MILLIMETERS (INCHES)
THE SURFACE TEXTURE VALUES ARE IN MICROMETERS (MICROINCHES)
THE SURFACE TEXTURE TO BE 1,6 (63) UNLESS SPECIFIED DIFFERENTLY
GEOMETRIC SYMBOLS ARE GIVEN IN THE ISO MANUAL R1101
REMOVE THE SHARP EDGES 0,10 TO 0,50 (0.004 TO 0.020)
MACHINE WHERE SHOWN 
SECTION THROUGH THE IP COMPRESSOR 
STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY 
STAGE 2 BLADE
STAGE 1 BLADE
STAGE 4 BLADE
C
IP COMPRESSOR
FRONT STUB SHAFT ASSEMBLY
72−32−31
01−350
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
General section view (Part 3)
Figure 8
Printed in Great Britain
TRENT 1000 72−K570
Page 46
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 50

dem0002681
STAGE 2−3
SEAL FINS
STAGE 3−4
SEAL FINS
STAGE 4−5
SEAL FINS
STAGE 5−6
SEAL FINS
STAGE 7−8
SEAL FINS
STAGE 8
SEAL FINS
STAGE 6−7
SEAL FINS
STAGE 1−2
SEAL FINS
PROTECTOR
TO COVER THE
3 SEAL FINS
AB
SECTION THROUGH THE IP COMPRESSOR
 STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
TO SHOW THE SEAL FINS PROTECTOR DETAILS
RRT119757
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
PROTECTOR
RRT119759
PROTECTOR
RRT119761
PROTECTOR
RRT119762
PROTECTOR
RRT119763
PROTECTOR
RRT119764
PROTECTOR
RRT119765
PROTECTOR
RRT119766
PROTECTOR
RRT119767
RRT119768
PROTECTOR
Protector details (Part 3)
Figure 9
Printed in Great Britain
TRENT 1000 72−K570
Page 47
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 51

dem0002684
POLYETHYLENE 
SHRINK WRAP
RRT119755
POLYMER TROUGH
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
Shrink wrap details (Part 3)
Figure 10
Printed in Great Britain
TRENT 1000 72−K570
Page 48
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 52

dem0002689 REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
RRT119745
BASE PLATE
RRT119748
SHAFT CENTRALISER
RRT119753
POLYMER TOP HAT COVER
POLYETHYLENE
SHRINK WRAP
POLYMER
PROTECTORS
Part arrangement on base plate (Part 3)
Figure 11
Printed in Great Britain
TRENT 1000 72−K570
Page 49
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 53

dem0002683
TO SHOW THE LOCK DETAILS
OF THE PROTECTORS 
VELCRO STRAP
SPLIT LINE
TYPICAL AT ALL STAGES
TO SHOW THE UNLOCK DETAILS
OF THE PROTECTORS 
TYPICAL AT ALL STAGES
VIEW AC
AC
VIEW AB
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
Protector lock/unlock details (All parts)
Figure 12
Printed in Great Britain
TRENT 1000 72−K570
Page 50
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 54

VIEW AT AA
TO SHOW THE MACHINING DETAILS
C
9,35  0.368
8,75  0.344
dem0002685
DIMENSION Y
DIMENSION X
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
Machining details (All parts)
Figure 13
Printed in Great Britain
TRENT 1000 72−K570
Page 51
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 55

HOIST
ADAPTER
NCU11636−3
ADAPTER
THUMB SCREW
(2 off)
LIFTER
PEG
LOCKING
LOCKING
SLEEVE
IP COMPRESSOR
STUB SHAFT
72−32−31
01−350
PLATE
(2 off)
(2 off)
dem0002686
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY 
RRT119750
(DAMPENING RING ASSEMBLY REMOVED)
NOT TO SCALE
Lifting/Clamping details (All parts)
Figure 14
Printed in Great Britain
TRENT 1000 72−K570
Page 52
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 56

dem0002692
RRT119751
LIFTING EYE TOOL
RRT119748
SHAFT CENTRALISER
RRT119745
BASE PLATE
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
THE DAMPENING
RING PIN
RRT119756
DAMPENING RING ASSSEMBLY
Tooling details (All parts)
Figure 15
Printed in Great Britain
TRENT 1000 72−K570
Page 53
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 57

dem0002690
VIEW AE
AE
IDENTITY MARKS ARE TO BE CONTAINED ON THE OUTER DIAMETER IN THE AREA IDENTIFIED 
TO THE INSTRUCTIONS
AD
IT IS PERMITTED TO USE MORE THAN ONE POSITION FOR THE IDENTITY MARKS
AD
AD
STAGE 1 DISC
REWORK OF THE IP COMPRESSOR STAGES 1 TO 8 ROTOR SHAFT ASSEMBLY
Identity marking details (All parts)
Figure 16
Printed in Great Britain
TRENT 1000 72−K570
Page 54
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

### Page 58

SUPPLEMENT - PRICES AND AVAILABILITY
This is a technical document not a quotation; any prices and delivery given are in
good faith without engagement.
Alternative parts may be supplied instead of parts listed. See Material Information
disposition instructions.
1. Modification Kit
Not applicable. Parts supplied as single line items.
2. Rework Parts:
Part No. Qty
Unit Price
US Dollars
LV18447 1 Price to be supplied on request
3. New Production Parts:
Part No. Qty
Unit Price
US Dollars
LV19601 1 Price to be supplied on request
NOTE: It is recommended that any consumable item(s) required to support the
Accomplishment of this Service Bulletin, be ordered at the same time as
the parts above.
4. Tools
None.
ENGINE - IP COMPRESSOR SHAFT - INTRODUCTION OF AN IP COMPRESSOR STAGES 1 TO 8 ROTOR
SHAFT ASSEMBLY FEATURING REVISED FRONT SEAL GEOMETRY - MOD.72-K570
Printed in Great Britain
TRENT 1000 72−K570
Supplement Page 1 of 1
Jun.15/21
Jun.15/21
TRENT 1000 SERIES
SERVICE BULLETIN

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
