# Rolls-Royce Non-Modification Service Bulletin RB.211-71-AG419: Revision 3

- Rights: © Rolls-Royce plc. Filed by the FAA in regulations.gov docket FAA-2019-0439, the docket of AD 2019-21-13. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Rolls-Royce Non-Modification Service Bulletin RB.211-71-AG419](https://openairdocs.org/service-documents/rolls-royce/rb211-71-ag419.md)
- Title as filed: SB RB.211-71-AG419 R03
- Pages: 45
- PDF: https://openairdocs.org/files/sha256/b6/97/b697daa84fb7971b91dbbfe7c60ff125c8bf0d4ce1fba52e4c9ccd930cf1f0db
- Page: https://openairdocs.org/service-documents/rolls-royce/rb211-71-ag419/file/b697daa84fb7

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

This document transmits Revision 3 to Service Bulletin RB211-71-AG419
Document History
Service Bulletin Revision Status Supplement Revision Status
Initial Issue Mar.10/11
Revision 1 May 10/11
Revision 2 Jun.26/14
Bulletin Revision 3
Remove Incorporate Reason for change
All pages of the
Service Bulletin
Pages 1 to 6 of the
Service Bulletin
To include the affected
nose cowl serial numbers in
Effectivity (1.A.), to
amend Compliance (1.D.(3))
to include reference of
anticipation of SB being
the subject of EASA AD, and
to include a new
requirement of initial and
follow on, inspection
intervals of 12 months.
Printed in Great Britain
Dec. 7/18
RB211 TRENT 700 SERIES PROPULSION SYSTEMS NON-MODIFICATION SERVICE BULLETIN
RB.211−71−AG419
Transmittal - Page 1 of 3
Date
ALERT
ALERT
CHECK THAT ALL PREVIOUS TRANSMITTALS HAVE BEEN INCORPORATED 
If any have not been received please advise Customer Data Services, Rolls-Royce plc, Derby, England 
©Rolls-Royce plc (date as above) Printed in Great Britain

### Page 2

All pages of
Appendix 1
Page 1 of Appendix 1 To include the affected
nose cowl serial numbers in
Effectivity (1.A.), to
amend Compliance (1.D.(3))
to include reference of
anticipation of SB being
the subject of EASA AD, and
to include a new
requirement of initial and
follow on, inspection
intervals of 12 months.
Printed in Great Britain
RB.211−71−AG419
Transmittal - Page 2

### Page 3

LIST OF EFFECTIVE PAGES
The effective pages to this Service Bulletin following incorporation of Revision
3 are as follows:
Page Revision Number Revision Date
Bulletin
R     1 3 Dec.7/18
R     2 3 Dec.7/18
R     3 3 Dec.7/18
R     4 3 Dec.7/18
R     5 3 Dec.7/18
R     6 3 Dec.7/18
Appendix 1
R     1 3 Dec.7/18
Printed in Great Britain
RB.211−71−AG419
Transmittal - Page 3

### Page 4

1. Planning Information
A. Effectivity
Airbus A330
All RB211 Trent 700 , SJ30020 and SJ30361 Air Intake Cowls fitted to the
following propulsion systems:
R
R
RB211 TRENT 768-60, TRENT 768-60/15, TRENT 768-60/16 Propulsion Systems not
incorporating SB 71-H205.
R
R
RB211 TRENT 772-60, TRENT 772-60/15, TRENT 772-60/16 Propulsion Systems not
incorporating SB 71-H205.
RB211 TRENT 772B-60, TRENT 772B-60/15, TRENT 772B-60/16 Propulsion Systems not
incorporating SB 71-H205.
RB211 TRENT 772C-60, TRENT 772C-60/15, TRENT 772C-60/16 Propulsion Systems not
incorporating SB 71-H205.
B. Reason
There have been fourR reported events in-service (including two in 2017) where
partial loss of a single acoustic panel has occurred on a Trent 700 air intake
cowl. It is understood the most likely cause is disbonding of the acoustic
panel facing sheet from the honeycomb core. To reduce the risk of service
disruption it has become necessary to introduce an inspection of the air intake
cowl acoustic panels to determine their condition.
Permitted damage limits and repairable damage limits have been provided to
assist operators with managing their fleet. Any acoustic panel found to have
damage outside of these limits must be rejected.
Revision 1 of this Non-Modification Service Bulletin (NMSB) was issued to
clarify when the inspection of the air intake cowls with a life less than 2000
hours or 5000 cycles since new is required (refer to Para 1.D.(3) Compliance).
Revision 2 of this NMSB was issued to clarify that Propulsion Systems
incorporating SB71-H205 do not require inspection as per this NMSB. The
accompanying Bombardier NMSB (RB211-NAC-71-018) was also amended to clarify the
Allowable Damage Limits by referring to disbond damage rather than general
damage, simplify the repair damage limits by removing the acoustic panel
zoning, and to refine the repair criteria.
R
R
R
R
R
R
NACELLE - POWERPLANT - AIR INTAKE COWL - INSPECTION OF INTAKE ACOUSTIC PANELS
(BOMBARDIER AEROSPACE-SHORTS NON-MODIFICATION SERVICE BULLETIN RB211-71-018) -
NON-MODIFICATION SERVICE BULLETIN - NON - MOD.71-AG419
Printed in Great Britain
RB.211−71−AG419
Page 1 of 6
Mar 10/11
Dec. 7/18R

### Page 5

Revision 3 of this NMSB is issued to declare the new inspection interval,
threshold and schedule. This revision also defines the revised Acceptable
Damage Limits (ADL's) and the revised Repairable Damage Limits (RDL's). This
revision also clarifies the applicability of repairs of the Acoustic Panel Wire
Mesh disbond. The accompanying Bombardier NMSB (RB211-NAC-71-018) has also been
revised to clarify the Allowable Damage Limits and clarify where expected tonal
changes will occur when carrying out the tap test inspection. This is achieved
by the inclusion of additional Figures highlighting the location of fixed
bracketry around the intake structure.
R
R
R
R
R
R
R
R
R
C. Description
This NMSB instructs a tap test inspection of the air intake cowl acoustic
panels to determine their condition.
Advise Bombardier Aerospace-Shorts and your assigned Rolls-Royce Airline
Support Team (AST)
R
R of NMSB accomplishment and inspection results. Refer to
Appendix 1.
D. Compliance
ALERT
This NMSB and the asscoiated Airbus SB A330-71-3024 are anticipatedR to the
subjectR of an EASA Airworthiness Directive (AD).
Rolls-Royce recommends that the actions detailed in Bombardier Aerospace-Shorts
NMSB RB211-NAC-71-018 and Para. 3. Accomplishment Instructions, are done at the
following opportunities given the age of the air intakes since new or life
since replacement of the air intake acoustic barrel assembly (all three
acoustic panels).
(1) The Bombardier Aerospace Shorts MNSB RB211-NAC-71-018 should be completed
at the following:
R
R
(a) Initial Inspection Threshold = 12 monthsR
(b) Follow-on Inspection to be completed at an interval = 12 monthsR
(c) Grace period = 6 months from NMSB issuance without exceeding 24 months
since last tap test
R
R
(2) If it can be shown that previous repair of the air intake introduced a new
pre Service Bulletin 71-H205 complete inner barrel assembly (ie the
replacement of all three acoustic panels completed at a Bombardier
Maintenance Repair Overhaul Facility, then the initial inspection must be
completed within 12 months post installation of the new barrel.
R
R
R
R
R
(3) If no damage is found during the initial inspection do a repeat inspection
of the air intake acoustic panels in accordance with this NMSB every 12
months.
R
R
R
Printed in Great Britain
RB.211−71−AG419
Page 2
Mar 10/11
Dec. 7/18R

### Page 6

(4) If damage is found, refer toR Accomplishment Instructions (Section 3, Table
1 of RB211-NAC-71-018) for follow on actions.
R
R
E. Approval
The technical content of this Non-Modification Service Bulletin was approved
under the authority of Design Organisation Approval EASA.21J.035 on Mar.9/11,
Apr.18/11, Jun.19/14R and was re-approved on Dec. 4/18.
The technical content under the JAR 25 regulation of this document is approved
under the authority of DOA No.R EASA.21J.031.
F. Manpower
Refer to Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018 Revision 3.R
G. Tooling Price and Availability
Refer to Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018 Revision 3.R
H. References
(1) Engine Manual, 71-61-00, Removal and Installation.
(2) This Service Bulletin is covered by aircraft Service Bulletin No.
A330-71-3024.
R
R
Under no circumstances should the inspected equipment, resulting from the
application of this SB, be installed on the aircraft type unless the
aircraft SB is approved.
R
R
R
(3) Structural Repair Manual, 54-01-06, Composite Structure Tap Test,
54-01-07, Acoustic Treatment Areas - Repair Limits, 54-10-01, Air Intake
Cowl - Identification, Repair 8 (FRSZ008), Repair 12 (FRSZ020) and Repair
13 (FRSZ025), Repair 14 (FRSZ014) and Repair 15 (FRSZ030,
RB211-NAC-71-018, Appendix C Air Intake Cowl Acoustic Liner Disbond
Repair).
R
R
R
R
R
R
(4) Engine Overhaul Processes Manual, TSD594-J.
(5) Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018 Revision 3.R
(6) EASA AD No.:2011-0173.
(7) Rolls-Royce RB211 Service Bulletin:
71-H205
Powerplant - Air intake cowl - Introduction of an air intake nose cowl
assembly with revised acoustic panels featuring increased density and
reduced cell size honeycomb core.
Printed in Great Britain
RB.211−71−AG419
Page 3
Mar 10/11
Dec. 7/18R

### Page 7

(8) Bombardier CMM, 71-60-00, Trent 700 Nose Cowl.R
Printed in Great Britain
RB.211−71−AG419
Page 4
Mar 10/11
Dec. 7/18R

### Page 8

2. Material Information
None.
Printed in Great Britain
RB.211−71−AG419
Page 5
Mar 10/11
Dec. 7/18R

### Page 9

3. Accomplishment Instructions
A. Refer toR Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018, Revision 3, para 3.
Accomplishment Instructions.R
B. Post requisite instructions.
(1) Remove all tools, equipment and unwanted materials from the work area.R
(2) Accomplishment of this NMSB should be recorded in the engine logbook or in
accordance with the local SB tracking system procedures. Metal stamp,
vibro etch or electro etch on the air intake cowl modification plate that
NMSB 71-AG419/x has been done.
R
R
R
R
NOTE: The forward slash and number indicate how many times this NMSB has
been done (for example, NMSB 71-AG419/1, denotes that one
inspection has been done).
R
R
R
Printed in Great Britain
RB.211−71−AG419
Page 6
Mar 10/11
Dec. 7/18R

### Page 10

Non-Modification Service Bulletin 71-AG419
1. If no instances of disbond have been found on all tested acoustic panels, or if
all instances of disbond on the panels have been repaired then record the
accomplishment of this NMSB in accordance with local Service Bulletin tracking
system procedures. Metal stamp, vibro etch or electro etch on the air intake
cowl modification plate that NMSB 71-AG419/x has been done.
NOTE: The forward slash and number indicate how many times this NMSB has been
done (for example, NMSB 71-AG419/1, denotes that one inspection has been done).
2. If fly-on is used, please notify Bombardier Aerospace-Shorts and your assigned
Rolls-Royce ASTR of the results of the initial inspection and all repeat
inspections, to make sure that an accurate record of all air intake cowl
inspections can be maintained.
3. Advise Bombardier Aerospace-Shorts and your assigned Rolls-Royce ASTR of NMSB
accomplishment and inspection results regardless of findings. An inspection
record sheet can be found in Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018,
Appendix B.
APPENDIX 1
Printed in Great Britain
RB.211−71−AG419
Appendix 1 - Page 1 of 1
Mar 10/11
Dec. 7/18R

### Page 11

Short Brothers plc
Customer Services
Airport Road
Belfast
BT3 9DZ
N. Ireland
Initial issue, 07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 1 of 35
SERVICE BULLETIN
NACELLE - POWERPLANT – AIR INTAKE COWL - INSPECTION OF INTAKE ACOUSTIC PANELS
          (NON-MODIFICATION SERVICE BULLETIN).
1. Planning Information
A. Effectivity
Airbus A330.
All RB211 Trent 700, SJ30020 and SJ30361 Air Intake Cowls fitted to the following propulsion
systems.
RB211 TRENT 768-60, TRENT 768-60/15, TRENT 768-60/16 propulsion systems not
incorporating SB 71-H205.
RB211 TRENT 772-60, TRENT 772-60/15, TRENT 772-60/16 propulsion systems not
incorporating SB 71-H205.
RB211 TRENT 772B-60, TRENT 772B-60/15, TRENT 772B-60/16 propulsion systems not
incorporating SB 71-H205.
RB211 TRENT 772C-60, TRENT 772C-60/15, TRENT 772C-60/16 propulsion systems not
incorporating SB 71-H205.
B. Reason
There have been several reported events in-service where partial loss of a single acoustic panel has
occurred on a Trent 700 air intake cowl. It is understood the most likely cause is disbonding or
separation of the acoustic panel facing sheet from the honeycomb core. To mitigate the risk of service
disruption it has become necessary to introduce an inspection of the air intake cowl acoustic panels to
determine their condition.
This Non –Modification Service Bulletin (NMSB) instructs a repeat inspection to report on and repair
disbond on the air intake cowl acoustic panels. Damage limits and repair damage limits have been
provided to assist operators with managing this task.
Return Appendix B (or similar form) to Bombardier Aerospace-Shorts and your assigned Rolls-Royce
Field Service representative.

### Page 12

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 2 of 35
C. Compliance
Refer to the Rolls-Royce Non Modification Service Bulletin 71-AG419 Revision 3.
NOTE: This Service Bulletin is not applicable to Air Intake Cowl part numbers SJ30810 and
SJ30820. These Air Intake Cowl part numbers feature honeycomb core with increased
density and reduced cell size.
D. Approval
Refer to the Rolls-Royce Non Modification Service Bulletin 71-AG419 Revision 3.
The technical content of this Service Bulletin has been approved under the authority of EASA Design
Organisation Approval No.EASA.21J.031.
E. Manpower
Estimated man-hours:
In-service
(1) Time to gain access: 0.5 Man hours (per air intake cowl).
(2) Time to inspect: 6.0 Man hours (per air intake cowl).
(3) Time to restore to serviceable condition: 2.0 Man hours (per air intake cowl).
In-shop
(4) Time to gain access: 0.5 Man hours (per air intake cowl).
(5) Time to inspect: 6.0 Man hours (per air intake cowl).
(6) Time to restore to serviceable condition: 2.0 Man hours (per air intake cowl).
NOTE: The parts affected by this Service Bulletin are accessible at overhaul, both on and off-wing.
F. Material - Price and Availability
Consumable materials.
OMat 150 Acetone (CH3) 2CO
(commercial grade O-A-51)
Commercially available
OMat 262 Temporary marker felt/fibre tip
(marker specification: -
RR Corp.spec. EM56752)
Commercially available
OMat 2/101 Absorbent cloth - lint free
(Allwipe Aerotex RS)
Commercially available
OMat 2/114 Gloves - lint free Commercially available

### Page 13

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 3 of 35
OMat 261 Temporary marker pencil/crayon Commercially available
OMat 237
or
OMat 237A
or
OMat 237B
or
OMat 237C
or
OMat 237D
or
OMat 237E
or
OMat 237F
Masking tape, adhesive.
Scotch 202 premium grade (A-
A-883 Ty l)
Scotch 213
Scotch 214
Scotch 232
Scotch 233
Scotch 236
Scotch 2311
Commercially available
NOTE: To identify consumable materials, refer to Overhaul Materials Manual, OMat.
G. Tooling - Price and Availability
(1) Tap testing tool.
Tap hammer may be purchased from industry sources or alternatively it can be locally manufactured
as per MIL-HDBK-337 from mild steel or brass only. Refer to Figure 7.
Note: Do not use tap hammers manufactured from Aluminium.
H. Weight and Balance
Not affected.

### Page 14

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 4 of 35
I. Electrical Load Data
Not affected.
J. References
(1) Engine Manual, 71-61-00, Removal/Installation.
(2) Airbus A330, Aircraft Maintenance Manual,
i. Chapter 70-20-01, Stripping and Cleaning.
ii. Chapter 71-00-00, 71-61-41 Maintenance Practices.
(3) RB211 Trent Structural Repair Manual,
i. Chapter, 54-01-06, Composite Structure Tap Test.
ii. Chapter, 54-01-07, Acoustic Treatment Areas – Repair Limits.
iii. Chapter, 54-10-01, Air Intake Cowl - Identification.
iv. Chapter, 54-10-01, Air Intake Cowl – Repair FRSZ008.
v. Chapter, 54-10-01, Air Intake Cowl – Repair FRSZ014.
(4) RB211 Trent Overhaul Materials Manual,
i. Section 1, Processing and Cleaning Materials.
ii. Section 2, Processing Sundries.
(5) Trent 700 Cowl Acoustic Panel Tap Test video (available on the Rolls-Royce Care website -
Services - Customer Training - Engine Technical Training).
K. Other Publications Affected
None.
L. Interchangeability of Parts
Not applicable.

### Page 15

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 5 of 35
2. Material Information
NOTE: Any acoustic panels found with disbonds between the honeycomb and the facing sheet, outside the
repair limits contained in this NMSB cannot be repaired as there are currently no approved repairs
available.
To replace acoustic panels it is recommended to return the inlet cowl to Bombardier Aerospace as the
inlet cowl will be required to be returned to the original manufacturing jigs. Operators should only use
original OEM acoustic panels when repairing inlet cowls.
Disbonds on the acoustic panel liner facing sheet may be repaired as instructed in Appendix C.
This NMSB is not applicable to disbonds between the wire mesh and the carbon ply of the facing
sheet.

### Page 16

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 6 of 35
3.  Accomplishment Instructions
CAUTION: IN ORDER TO REDUCE THE POTENTIAL FOR MULTIPLE ENGINE IN-FLIGHT
SHUTDOWN, POWER LOSS, OR OTHER ANOMALY DUE TO MAINTENANCE
ERROR, ROLLS-ROYCE RECOMMENDS THAT OPERATORS AVOID
PERFORMING MAINTENANCE ON MULTIPLE ENGINES INSTALLED ON THE
SAME AIRCRAFT AT THE SAME TIME. IF IT IS NOT POSSIBLE TO AVOID
MAINTENANCE ON MORE THAN ONE ENGINE AT THE SAME TIME, ROLLS-
ROYCE RECOMMENDS THAT ADDITIONAL CONTROLS ARE APPLIED IN
ORDER TO ENSURE THATMAINTENANCE TASKS HAVE BEEN COMPLETED AS
DEFINED. MAINTENANCE GUIDELINES SHOULD BE REVISED, WHERE
POSSIBLE, TO PROMOTE THIS RECOMMENDATION.
A. Pre-requisite Instructions
The actions contained in Bombardier Aerospace-Shorts NMSB RB211-NAC-71-018, ‘3.Accomplishment
Instructions’ have been developed to allow inspections to be completed with the air intake cowl installed on-
wing. It is also permitted for the inspection to be accomplished with the air intake-cowl removed.
NOTE: To enable an effective tap test inspection to be done, the aircraft or air intake-cowl needs to
be positioned in an environment that is not unduly affected by background noise as this may
result in a false indication.
B. Inspect the air intake cowl acoustic panels (Ref. Figure 1).
WARNING: WHEN YOU DO THIS REPAIR YOU MUST WEAR PROTECTIVE CLOTHING,
GLOVES, DUST MASK AND SAFETY GOGGLES TO PROTECT YOU AGAINST
DUST AND LOOSE PARTICLES WHICH CAN BE DANGEROUS TO YOUR HEALTH.
WHEN YOU ABRADE, CUT OR MACHINE THE CARBON FIBRE COMPOSITE
MATERIAL, THE DUST PARTICLES PRODUCED ARE TOXIC AND CAN DAMAGE
YOUR HEALTH. USE EXTRACTION EQUIPMENT IF IN AN ENCLOSED PLACE.
AVOID BREATHING THE DUST AND AVOID PROLONGED CONTACT OF THE
DUST WITH YOUR SKIN. GET MEDICAL AID IF YOU GET DUST PARTICLES IN
YOUR MOUTH OR EYES OR IF THEY HAVE AN EFFECT ON YOUR SKIN. REFER
TO LOCAL HEALTH AND SAFETY REGULATIONS.
WARNING: WHEN YOU USE CLEANING MATERIALS, COATINGS, ADHESIVES AND
SEALANT, REFER TO THE MANUFACTURER’S CONTROL AND APPLICATION
INSTRUCTIONS AND SAFETY NOTICES.
WARNING: BEFORE YOU USE CHEMICALS, READ, UNDERSTAND AND OBEY ALL SAFETY
INSTRUCTIONS FOR THE CHEMICALS. THESE INSTRUCTIONS INCLUDE
INSTRUCTIONS FROM THE MANUFACTURER, THE MATERIAL SAFETY DATA
SHEET (MSDS), AND GOVERNMENT REGULATIONS. CHEMICALS MAY CAUSE
INJURY TO YOU OR MAKE YOU SICK WHEN SAFETY INSTRUCTIONS ARE NOT
OBEYED. AN MSDS GIVES INSTRUCTIONS ON HOW YOU MUST SAFELY USE,
KEEP AND DISCARD CHEMICALS. GET INSTRUCTIONS FROM YOUR
EMPLOYER ON HOW YOU MUST SAFELY USE, KEEP AND DISCARD
CHEMICALS.

### Page 17

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 7 of 35
CAUTION: IT IS RECOMMENDED THAT YOU USE PROTECTIVE MATS (P/N HU55142) WHEN
YOU DO THE INSPECTION OF THE AIR INTAKE ACOUSTIC PANELS. THIS
PREVENTS DAMAGE TO THE ACOUSTIC PANELS.
(1) Preparation of the Air Intake Acoustic Panels.
Clean the surface of the air intake cowl acoustic panels with an OMat 2/101 lint-free cloth moistened with
OMat 150 Acetone solvent. Make sure you use OMat 2/114 lint-free gloves when you clean components.
NOTE: Make sure you wipe the surface of the parts before the solvent evaporates.
(2) Inspection of the Air Intake Acoustic Panels.
a. Do a visual inspection of all 3 air intake cowl acoustic panels before you do the NDT inspection.
Make a mark on the panel of any defects or areas of interest.
NOTE: Inspect Panel 1 and Panel 3 before you inspect Panel 2.
NOTE: The effectiveness of the tap test method in finding the nature of disbond can be affected
by external factors, eg background noise, hearing sensitivity and tapping force. To get
best inspection results, do the tap test with a uniform tapping force and a uniform tap
repetition speed in a quiet location.
NOTE: For tap test best practice, refer to the video ‘Trent 700 Cowl Acoustic Panel Tap Test’
which is available on the Rolls-Royce Care website - Services - Customer Training -
Engine Technical Training.
NOTE: It is easier to check for areas of disbond if you divide each panel into two sections
(section 1 (edge band – including the area of foaming adhesive) and section 2
(honeycomb area requiring disbond inspection)) as shown. Refer to Figure 1 sheet 1 and
sheet 2.
Section 1. Apply masking tape (OMat 237) or use a temporary marker pencil/crayon (OMat 261 or
suitable alternative) to make a 25mm (1inch) border on the front face of each acoustic
panel taken from the edges of the acoustic area (refer to Figure 1 sheet 2). Do step (b)
and inspect the marked area thoroughly.
Section 2. Apply masking tape (OMat 237) or use a temporary marker pencil/crayon (OMat 261 or
suitable alternative) to make a grid pattern of 150mm (6 inch) squares on the front face
of each acoustic panel and around the EEC Duct and P20T20 Probe (refer to Figure 1
sheet 2). Do step (b) and inspect the marked area thoroughly.
b. Inspect the complete surface of all 3 air intake cowl acoustic panels for disbond between the acoustic
panel lining and Nomex Honeycomb core using the tap test procedure that follows: -
1. Use a temporary marker pencil/crayon (OMat 261 or suitable alternative) to mark the
approximate location of the three P2T2 harness brackets and the bulkhead attachment
angles. Refer to Figure 1 sheet 3 and sheet 4.
2. On each grid, press down on the surface of the panel. Any movement of the surface may
indicate a disbond. Make a mark on the panel of any areas where movement has
occurred. Refer to Figure 1 sheet 1.

### Page 18

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 8 of 35
CAUTION: USE THE ROUND HEAD OF THE TAP HAMMER FOR THE TAP
TEST. IF YOU USE THE POINTED HEAD OF THE TAP HAMMER
DAMAGE TO THE PANEL CAN OCCUR.
3. Tap test at intervals of up to 20 mm (approximately 0.75in) across the full surface of
each air intake cowl acoustic panel with the ball end of the tap-testing tool. On each grid,
tap test in a wave pattern in the forward/aft direction and then in the inboard/outboard
direction. Refer to Figure 1 sheet 5.
NOTE: During the tap test, a tight tone will indicate a good bond, a dull tone may indicate
a disbond.
4. Take note of any change of pitch in the sound given out from the air intake cowl acoustic
panels. A change of pitch may indicate a disbond at that location.
NOTE: The sound during the tap test can be different at the locations where the 3 P2T2
harness brackets and the bulkhead attachment angles are installed. A change of
pitch at these locations may not indicate a disbond. Refer to Figure 1 sheet 3 and
sheet 4.
NOTE: Expanded foam adhesive is used to bond the materials around the edges of the
panels and this can cause a different sound during the tap test.
5. If a disbond is detected, tap test at intervals of no greater than 12mm (approximately 0.5
inch) across the full surface of the area of interest to determine the dimensions of the
delamination or disbond.
6. If a disbond is detected, it may not be necessary to do a full repair (as per Appendix C)
on the disbonded area. To do the minimum amount of rework to the panel do the steps
that follow:
NOTE: The Tap Test may identify disbond between the wire mesh and the carbon ply and
also between the carbon ply and the honeycomb core. Method A and Method B
below will allow the operator to determine the nature of the disbond and the
appropriate repair.
Method A – Push Test / Tape Test
(a) On the damaged area, push your hand along the acoustic panel surface in a
movement parallel to the wire mesh.
(a1) Make a note of any rippling of the wire mesh on the panel surface.
NOTE: If rippling can be seen then there is a disbond between the wire mesh and
the carbon ply.
Or
(b) Apply tape (OMat 237 or suitable alternative) on the damaged area of the acoustic
panel and slowly pull the tape away.
(b1) Make a note if a bubble-like shape can be seen between the wire mesh and
the carbon ply.
NOTE: If a bubble-like shape can be seen then there is a disbond between the
wire mesh and the carbon ply.

### Page 19

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 9 of 35
(c) If it is determined from Method A (Push Test / Tape Test) that there is a disbond
between the wire mesh and the carbon ply, then carefully remove the affected wire
mesh.
(d) Do Method B.
Method B – Press Test
(e) On the damaged area from where the wire mesh has been removed, press your
thumb down perpendicular to the acoustic panel surface.
(e1) Make a note of any movement of the panel surface.
NOTE: If any movement has occurred then there is a disbond between the carbon
ply and the honeycomb core.
NOTE: When you press down on the acoustic panel, a faint audible clicking
noise will indicate that there is a disbond between the carbon ply and the
honeycomb core.
(e2) If there is no movement of the carbon ply, do a tap test of the carbon ply
area to check for a disbond.
NOTE: The effectiveness of the tap test method in finding the nature of disbond
can be affected by external factors, eg background noise, hearing
sensitivity and tapping force. To get best inspection results, do the tap
test with a uniform tapping force and a uniform tap repetition speed in a
quiet location.
NOTE: For tap test best practice, refer to the video ‘Trent 700 Cowl Acoustic
Panel Tap Test’ which is available on the Rolls-Royce Care website -
Services - Customer Training - Engine Technical Training.
(f) If it is determined that that there is no disbond between the carbon ply and the
honeycomb core then, if wire mesh has been removed - repair the acoustic panel as
per SRM/CMM repair FRSZ008 or request a Technical Variance (TV).
(g) If it is determined that that there is a disbond between the carbon ply and the
honeycomb core then do step (7).
7. Use OMat 262 marking pen to make a mark on the air intake cowl around any areas of
disbond between the acoustic panel lining and the Nomex honeycomb core.
8. Record any areas of disbond, along with their closest repaired disbonds in Appendix B,
“Non- destructive Inspection Report for Bombardier Aerospace–Shorts”.
9. Any operator who has found no evidence of disbond should also record this in
Appendix B.

### Page 20

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 10 of 35
C. Allowable Damage Limits.
Depending on the extent of the air intake cowl acoustic panel disbond found the following allowable
damage limits may be applied.
NOTE: It is permissible to fly-on with multiple occurrences of Level 1 to Level 3 disbond on
each individual air intake cowl acoustic panel, provided that there is a minimum distance
(Y) between disbonded areas equal to or greater than 5 times the length (A) of the largest
area of damage. Refer to Figure 1 sheet 6 view A.
NOTE: If two or more disbond damages are within a distance (Y) that is less than 5 times the
length (A) of the largest damage, consider the two or more damages as a single one.
Refer to Figure 1 sheet 6 view B.
NOTE: It is permissible to fly-on with multiple occurrences of Level 1 to Level 3 disbond if there
are existing repaired areas up to a 1 inch diameter, repaired as per Structural Repair
Manual (SRM)/Component Maintenance Manual (CMM) repairs FRSZ008, FRSZ020
and FRSZ025. The minimum distance between damage areas should be 5 times the length
of the largest damaged/repaired area. Refer to Figure 1 sheet 6 view C.
NOTE: If an aircraft is returned to service under fly on conditions, the tap test inspection will have
to be repeated on the disbonded region of the air intake acoustic panel at the prescribed
inspection interval to establish if it has become larger. If the damage has become larger,
then the relevant acceptance limits and inspection intervals will apply.
(1) The following limits show the levels of disbond, for each acoustic panel, where fly-on is permissible.
Multiple occurrences of Level 1 to Level 3 disbonds are allowed, provided that the stated damage
separation limits are not exceeded.
Table 1
Levels of disbond Permissible disbond Action required
Level 1 Up to 152,4 mm (6 in.) by 152,6 mm (6 in.) -
provided that the maximum length of any side of
the area is 254 mm (10 in.)1 or the disbond area
can fit inside 101,6 mm (4 in.) by 101,6 mm (4 in.)
template
Repeat the inspection every 50 flight
cycles local to the disbond area or
repair the affected unit before the 50
flight cycles has expired.
Level 2 152,4 mm (6 in.) by 152,6 mm (6 in.) up to
203,2 mm (8 in.) by 203,2 mm (8 in.) - provided
that the maximum length of any side of the area is
254 mm (10 in.) 1 or the disbond area can fit inside
203,2 mm (8 in.) by 203,2 mm (8 in.) template
Repair the affected unit before the
10 flight cycles has expired.
Level 3 203,2 mm (8 in.) by 203,2 mm (8 in.) up to
254 mm (10 in.) by 254 mm (10 in.) - provided
that the disbond area fits within a 254 mm (10 in.)
by 254 mm (10 in.) 1 square template.
Replace the affected unit on-wing
within 10 flight cycles.

### Page 21

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 11 of 35
Notes:
1 Damage limits are only permissible when the minimum distance between the disbonded areas (including the
nearest disbond repair) does not exceed 5 times the length of the largest area of disbond damage.
If the level of disbond found is greater than the permitted damage limits provided, then no fly-on is permissible.
Replace the affected air intake cowl before the next flight.
If the cumulative area of disbond, due to one or more damaged areas found across the panel, is greater than
64500 mm2 (100 in2) then no fly-on is permissible. Replace the affected air intake cowl before the next flight.
(2) If the level of disbond found is greater than the permitted damage limits provided, then no fly-on is
permissible. Replace the affected air intake cowl before the next flight.
(3) It is acceptable to repair the damaged area as instructed in the Structural Repair Manual (SRM) /
Component Maintenance Manual (CMM) if the level of disbond is within the limits of the
SRM/CMM repairs and if the the total size of accumulated repairs do not exceed a maximum area of
64500 mm2 (100 in2) for each acoustic panel.
(4) If it is determined from Method A (Push Test / Tape Test) that there is a disbond between the wire
mesh and the carbon ply only, then this service bulletin is not applicable. Repair the acoustic panel as
per SRM/CMM repair FRSZ008 or request a Technical Variance (TV).
D. Post-requisite Instructions
Remove all tools, equipment and unwanted materials from the work area.
(1) Refer to the Rolls Royce Non Modification Service Bulletin: 71-AG419 Revision 3.
(2) Where previously removed, re-install the air intake cowl onto the engine in accordance with Engine
Manual 71-61-00, Removal/Installation or Aircraft Maintenance Manual 71-61-41, Maintenance
Practices.
E. A record of accomplishment is required.
If no instances of disbond have been found on any acoustic panel, or if all instances of disbond on each panel
have been fully repaired, then record in the Engine Log book and metal stamp, vibro etch or electro etch on the
air intake cowl modification plate that NMSB 71-AG419 Revision 3 has been completed.
An operator who has completed this NMSB and has chosen to continue operating under fly on conditions,
should record in the Engine Log that NMSB 71-AG419 Revision 3 has been completed.

### Page 22 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
PANEL 1  PROBE P2T2  RAD 345  O DEGREES  RADIAL  (SJ30201 or  SJ30737)  PANEL 3
(SJ30203)
EEC INLET
- RAD 63
EEC OUTLET
RAD 80.5
RADIAL
RADIAL  135 DEGREES
ACOUSTIC LINER  225 DEGREES
SEGMENTS  PANEL 2
(3 OFF)  (SJ30295)
PANEL 1  PANEL 2  PANEL 3
RAD 255
RAD O  RAD 135
•WD
RAD 225  SJ30203 RAD 135  SJ30295  RAD O  SJ30201 or  SJ30737
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 1 of 6
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 12 of 35

### Page 23 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
RAD 225°  RAD 0°
RADIAL JOINT  PANEL 1  RADIAL JOINT
FASTENERS
EDGE OF
ACOUSTIC
AREA
P2T2
PROBE
-- AFT EDGE OF PANEL
RAD 135°  RAD 225°
RADIAL JOINT  PANEL 2  RADIAL JOINT
• FASTENERS
EDGE OF
• ACOUSTIC
AREA
AFT EDGE OF PANEL
RAD 0°  RAD 135°
RADIAL JOINT  PANEL 3  RADIAL JOINT
EDGE OF
ACOUSTIC
AREA
EEC
EEC  OUTLET
INLET
FASTENERS  rb211-nac-71-0018-01
AFT EDGE OF PANEL
NOTES
Section 1 Temporary mark border 1.00 in. (25,4 mm) from edge of acoustic area.
Section 2 Temporary mark grid pattern of 6.0 in. (152 mm) squares on remaining acoustic area.
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 2 of 6
Initial issue, 07 March 2011  RB211-NAC-71-018
Revision 3, 05 December 2018
Page 13 of 35

### Page 24 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
RAD 225°  PANEL 1  P2T2  RAD 0°
RADIAL JOINT  RADIAL JOINT
PROBE
FASTENERS
P2T2 HARNESS /1
BRACKETS
BULKHEAD  (3 OFF)
ATTACHMENT
ANGLE
- AFT EDGE OF PANEL
RAD 135°  RAD 225°
RADIAL JOINT  PANEL 2  RADIAL JOINT
FASTENERS
BULKHEAD
ATTACHMENT
ANGLE
• AFT EDGE OF PANEL
RAD 0°  RAD 135°
RADIAL JOINT  PANEL 3  RADIAL JOINT
EEC
INLET
BULKHEAD  ATTACHMENT  • 0~  OUTLET  EEC  rb211-nac-71-0018-06
ANGLE  = = =  FASTENERS
1  .......  _._ AFT EDGE OF PANEL
NOTE
1 Refer to figure 1 sheet 3 for approximate dimensions.
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 3 of 6
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 14 of 35

### Page 25 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
P2T2 PROBE  RAD 0°
(PANEL 1 ONLY)  RADIAL JOINT  EDGE OF PANEL
7 in.
(178 mm)
29 in.
5 in.  (737 mm)
- (127 mm)
22 in.
(559 mm)
8.5 in.
(216 mm)
13 in.
(330 mm)
7 in.
(177 mm)
6 in.
(152 mm)
BULKHEAD ATTACHMENT ANGLE
AFT EDGE OF PANEL  (TYPICAL 3 PANELS)
1.5 in.  3.5 in.
(38 mm)  (89 mm)
3 in.  3 in.
(76 mm)  (76 mm)  rb211-nac-71-0018-10
P2T2 HARNESS  P2T2 HARNESS
BRACKET  BRACKET
(PANEL 1 ONLY)  (PANEL 1 ONLY)
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 4 of 6
Initial issue, 07 March 2011  RB211-NAC-71-018
Revision 3, 05 December 2018
Page 15 of 35

### Page 26 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
TYPICAL PANEL
A
INSPECTION PATH 1  INSPECTION PATH 2  rb211-nac-71-0018-07
(Typical forward/aft grid inspection path  (Typical inboard/outboard grid inspection path
with a 0.75in. (20mm) pitch)  with a 0.75in. (20mm) pitch)
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 5 of 6
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 16 of 35

### Page 27 (OCR)

SERVICE BULLETIN RB211-NAC-71-018
RADIAL JOINT  RADIAL JOINT
Typical Panel
• FASTENERS
EXISTING
REPAIRS
BULKHEAD
ATTACHMENT  DAMAGED AREA
ANGLE
AFT EDGE OF PANEL
A = Length of largest area of damage
Y = Distance between disbonded areas / existing repairs must be equal to or greater than 5 x A
RADIAL JOINT  RADIAL JOINT
Typical Panel
- FASTENERS
BULKHEAD
ATTACHMENT  Y
ANGLE  = DAMAGED AREA =
- AFT EDGE OF PANEL
A = Length of largest area of damage  B
Y = Distance between disbonded areas
- Area to be treated as one disbond if Y is less than 5 x A
RADIAL JOINT  RADIAL JOINT
Typical Panel
DAMAGED AREA
• FASTENERS
BULKHEAD  EXISTING
ATTACHMENT  REPAIR
ANGLE  = = =
- AFT EDGE OF PANEL
B = Length of largest area of damage / repair
Z = Distance between disbonded area and existing repair must be equal to or greater than 5 x B
Inspection of the Intake Cowl Acoustic Panels
Figure 1 sheet 6 of 6
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 17 of 35

### Page 28

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 18 of 35
Appendix A
Non-Modification Service Bulletin 71-018
1. If fly on is used, please notify Bombardier Aerospace–Shorts and your assigned Rolls-Royce FSO of the
results of the initial inspection and all repeat inspections, to ensure that an accurate record of all air intake
cowl inspections can be maintained.
2. If no instances of disbond have been found on all tested acoustic panel, or if all instances of disbond on the
panels have been repaired, then record accomplishment of this NMSB in accordance with local Service
Bulletin tracking system procedures. Metal Stamp, vibro-etch or electro-etch on the air intake cowl
modification plate that NMSB 71-AG419 Revision 3/x has been done.
NOTE: Put a forward slash and a number to indicate how many times this NMSB has been done (e.g. NMSB 71-
AG419 Revision 3/1 would be one inspection done).
3. Advise Bombardier Aerospace-Shorts and your assigned Rolls-Royce FSO of NMSB accomplishment and
inspection results regardless of findings. An inspection record sheet can be found in Appendix B.
4. Report All findings
Return the Non Destructive Inspection Report for Bombardier Aerospace – Shorts to the address that
follows: -
Customer Services
Short Brothers PLC
PO Box 241
Belfast BT3 9DZ
Northern Ireland
FAO:  In-Service Engineering.
Email: shorts.support@aero.bombardier.com

### Page 29

SERVICE BULLETIN RB211-NAC-71-018
Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 19 of 35
Appendix B
Inspection Report
Non Destructive Inspection Report for Bombardier Aerospace - Shorts
See over

### Page 30

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 20 of 35
Appendix B: Inspection Report
1 TITLE 2 PAGE 3 REPAIR
SURVEY NO.
4 REV
Non Destructive Inspection Report for Bombardier Aerospace -
Shorts 1 OF 3
_ _ _ _ _ _ _ _ _
1
5. A/C TAIL
NUMBER
_ _ _ INTAKE POSITION _ _ _
6. DATE 7. CONTRACT  8. COMPONENT
DESCRIPTION
9. PART
NUMBER
10. SERIAL
NUMBER
_ _ / _ _ / _ _ _ _
(DD/MM/YYYY)
TRENT AIR INTAKE COWL SJ30361
SB/RR/T700/_ _ _ _
(Insert 4 digit serial
number)
11. HOURS _ _ _ _ _ CYCLES _ _ _ _ _
12. REASON FOR NDI
100% TAP TEST OF ALL AIR INTAKE COWL PANELS, BETWEEN THE ACOUSTIC LINING AND NOMEX
HONEYCOMB CORE, TO INSPECT FOR AREAS OF DISBOND.
13. SUMMARY OF FINDINGS
Tap test Insp:-
Panel 1: - _ _ _ off areas of disbond found or tick here _ _ _ if no disbonds found.
Panel 2: - _ _ _ off areas of disbond found or tick here _ _ _ if no disbonds found.
Panel 3: - _ _ _ off areas of disbond found or tick here _ _ _ if no disbonds found.
(RECORD LOCATION & SIZE OF DISBONDS ON DIAGRAM 1)
14. INSPECTION
JOB TITLE NAME MODIFIED
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ / _ _ / _ _ _ _
(DD/MM/YYYY)
15. TAP TEST
TECHNIQUE USED TAP TEST STAMP
EQUIPMENT USED TAP TEST TOOL
SIGNATURE NAME DATE

### Page 31 (OCR)

1 TITLE  2 PAGE  3 REPAIR SURVEY No.  4 REV
- Shorts  Non Destructive Inspection Report for Bombardier Aerospace  2 OF 3  -___=  1
Figure 2 (TAP TEST INSPECTION - RESULTS)
Detail tap tested areas of disbond as: - • Detail existing repair areas as: - o
(Dimensions of disbond/repair area and applicable dimensions from panel edges to be included).
PANEL 1  PROBE P2T2  RAD 345  O DEGREES  RADIAL  (SJ30201 or  PANEL 3  SJ30737)
(SJ30203)
EEC INLET
RAD 63
EEC OUTLET
RAD 80.5
RADIAL
RADIAL  135 DEGREES
ACOUSTIC LINER  225 DEGREES
SEGMENTS  PANEL 2
(3 OFF)  (SJ30295)
PANEL 1  PANEL 2  PANEL 3
RAD 255
RAD 0  RAD 135
FWD
RAD 225  SJ30203 RAD 135  SJ30295  RAD O  SJ30201 or  SJ30737
Non-Destructive Inspection Report
Figure 2 sheet 1 of 2.
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 21 of 35

### Page 32 (OCR)

1 TITLE  2 PAGE  3 REPAIR SURVEY No  4 REV
- Shorts  Non Destructive Inspection Report for Bombardier Aerospace  3 OF 3  1
RADIAL JOINT  RAD 225°  PANEL 1  PROBE  P2T2  RADIAL JOINT  RAD 0°
FASTENERS
P2T2 HARNESS /1
BRACKETS
BULKHEAD  (3 OFF)
ATTACHMENT_
ANGLE
-- AFT EDGE OF PANEL
RAD 135°  RAD 225°
RADIAL JOINT  PANEL 2  RADIAL JOINT
FASTENERS
BULKHEAD
ATTACHMENT
ANGLE
AFT EDGE OF PANEL
RAD 0°  RAD 135°
RADIAL JOINT  PANEL 3  RADIAL JOINT
EEC
INLET
BULKHEAD  ATTACHMENT  OUTLET  EEC  rb211-nac-71-0018-06
ANGLE  ======  - FASTENERS
•. _AFT EDGE OF PANEL
NOTE
1 Refer to figure 1 sheet 3 for approximate dimensions.
Non-Destructive Inspection Report
Figure 2 sheet 2 of 2.
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 22 of 35

### Page 33

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 23 of 35
Appendix C
Air Intake Cowl Acoustic Liner Disbond Repair (Repair No. FRSZ030)
1. General
(A) This repair may be used to repair an intake cowl acoustic liner facing sheet disbond in conjunction
with NMSB 71-AG419 Revision 3 only.
(B) Repair must be carried out under controlled conditions with the humidity at 50 percent or less.
(C) This repair removes the disbonded facing sheet, places a layer of adhesive on the honeycomb cells by
laying the adhesive onto a rubber mat, partially curing the adhesive and then pressing the adhesive
into the honeycomb core. The adhesive is cured and a carbon repair ply is bonded on top.
(D) The repair damage limits are -:
(1) A maximum damage size for a single damage of 203,20mm (8.00in.) by 203,20mm (8.00in.) -
provided that the maximum length of any side of the area does not exceed 254mm (10in) – in the
acoustic area of the panel.
(2) It is permissible to repair multiple damages to the panel, providing there is a minimum distance
between other disbond damage areas of five times the length of the largest damage. Refer to
Figure 1 sheet 5.
(3) There must be a minimum distance between the damage areas and any existing repaired area,
equal to five times the length of the largest damage. Refer to Figure 1 sheet 5.
(4) The total loss of acoustic area must not exceed the limits given in Structural Repair Manual
(SRM) 54-01-07 Acoustic Treatment Areas – Repair limits for repair of the acoustically treated
areas.
(E)  Damage that is not within the limits of this repair must be referred to Bombardier Aerospace-Shorts.
(F) This repair can be carried out on-wing and at any position on the acoustic panels. Support is applied
to the repair ply or rubber mat by vacuum bagging the area. In order to pull a satisfactory vacuum,
the open acoustic cells around the repair area need to be closed using OMat 2/30 Teflon tape.
(G) Tasks identified by OP TASK are in the Engine Overhaul Process Manual, TSD594-J. Tasks
identified by SRM TASK are in the Standard Practices Manual.
2. References
(A) Structural Repair Manual, 54-01-06 Tap test, 54-01-07, Acoustic Treatment Areas – Repair Limits,
54-10-01, Identification.
(B) Aircraft Maintenance Manual, 70-20-01, Cleaning, 71-61-41, Air Intake Cowl –
Removal/Installation.

### Page 34

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 24 of 35
3. Equipment and Material
(1) Standard equipment:
Heat lamp, 70 to 100 deg. C. (158 to 212 deg. F.)
Suction cleaner
Standard workshop tools
Vacuum pump
Vacuum bag fitting
4. Consumable Materials
OMat 150 Acetone Comercially available
OMat 2/30 Teflon tape Comercially available
OMat 2/101 Lint-free cloth Comercially available
OMat 2/114 Lint-free gloves Comercially available
OMat 8/52 EA934NA adhesive Comercially available
OMat 212 Brush Comercially available
OMat 262 Marker pen Comercially available
OMat 8/160 EA9390 adhesive Comercially available
OMat 8/206A Carbon fibre (8HS) satin fabric Comercially available
OMat 2/31 Vacuum bag Comercially available
OMat 2/110 Tape, adhesive vacuum bag seal Comercially available
OMat 2/111 Breather cloth Comercially available
OMat 2/112 Porous parting film Comercially available
OMat 2/113 Non- porous parting film Comercially available
OMat 5/31 Abrasive paper Comercially available
OMat 237 Masking tape, adhesive. Scotch 202
premium grade (A-A-883 Ty l)
Comercially available
5.  Component Material
PART IDENT MATERIAL
Air intake cowl Composite structure

### Page 35

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 25 of 35
6. Repair the Air Intake Cowl Acoustic Liner Disbond.
WARNING:  WHEN YOU DO THIS REPAIR YOU MUST WEAR PROTECTIVE CLOTHING, GLOVES,
DUST MASK AND SAFETY GOGGLES TO PROTECT YOU AGAINST DUST AND
LOOSE PARTICLES WHICH CAN BE DANGEROUS TO YOUR HEALTH. WHEN YOU
ABRADE, CUT OR MACHINE THE CARBON FIBRE COMPOSITE MATERIAL, THE
DUST PARTICLES PRODUCED ARE TOXIC AND CAN DAMAGE YOUR HEALTH. USE
EXTRACTION EQUIPMENT IF IN AN ENCLOSED PLACE. AVOID BREATHING THE
DUST OR PROLONGED CONTACT OF THE DUST WITH YOUR SKIN. GET MEDICAL
AID IF YOU GET DUST PARTICLES IN YOUR MOUTH, EYES OR IF THEY HAVE AN
EFFECT ON YOUR SKIN. REFER TO LOCAL HEALTH AND SAFETY REGULATIONS.
WARNING: WHEN YOU USE CLEANING MATERIALS, COATINGS, ADHESIVES AND SEALANT,
REFER TO THE MANUFACTURER'S CONTROL AND APPLICATION INSTRUCTIONS
AND SAFETY NOTICES.
A.  Prepare the damaged area for repair. Refer to Fig. 3 (A and B).
(1) Clean the damaged area with OMat 2/101 Lint free cloth, moistened with solvent OMat 150 Acetone and
wipe the area dry before the solvent evaporates. Wear OMat 2/114 Lint free gloves.
(2) Make a visual inspection of the damage and do a tap test in accordance with Structural Repair Manual, 54-
01-06, Tap Test, to identify the size of the damaged area. Measure the extent of the damage. Make sure that
the damage is within the limits listed in this repair scheme and the limits listed in Structural Repair Manual
54-10-01, Identification.
(3) Use an OMat 262 marker pen to mark out the damaged area on the acoustic liner that is to be removed. The
cut out area should be a regular shape with rounded corners of 12,7 mm. (0.5in.) minimum radius.
WARNING:  WEAR PROTECTIVE CLOTHING, GLOVES, DUST MASK AND SAFETY GOGGLES.
WHEN COMPOSITE MATERIALS ARE CUT OR SANDED, DUST AND LOOSE
PARTICLES ARE PRODUCED WHICH ARE POTENTIAL HEALTH HAZARDS. DO
NOT BREATHE THE DUST.
(4) Use a suitable high-speed rotar cutting tool to carefully remove the facing sheet (Refer to Fig. 4(A)) by
cutting along the area marked with the marker. Make sure the cutting blade cuts the facing sheet only and
does not damage the honeycomb core. Remove the facing sheet from the disbond area.
B.  Clean the repair area.
(1) Remove all unwanted material from the repair area with a suction cleaner.
WARNING: BEFORE YOU USE CHEMICALS, READ, UNDERSTAND, AND OBEY ALL SAFETY
INSTRUCTIONS FOR THE CHEMICALS. THESE INSTRUCTIONS INCLUDE
INSTRUCTIONS FROM THE MANUFACTURER, THE MATERIAL SAFETY DATA
SHEET (MSDS) AND GOVERNMENT REGULATIONS. CHEMICALS MAY CAUSE
INJURY TO YOU OR MAKE YOU SICK WHEN SAFETY INSTRUCTIONS ARE NOT
OBEYED. AN MSDS GIVES INSTRUCTIONS ON HOW YOU MUST SAFELY USE,
KEEP, AND DISCARD CHEMICALS. GET INSTRUCTIONS FROM YOUR
EMPLOYER ON HOW YOU MUST SAFELY USE, KEEP AND DISCARD
CHEMICALS.
(2) Clean the damaged area with OMat 2/101 Lint free cloth moistened with solvent OMat 150 Acetone. Wipe
the area dry before the solvent evaporates. Wear OMat 2/114 Lint free gloves.
(3) Dry the repair area for 6 hours at 80 deg C (176 deg. F.) using heat lamps.
NOTE: The repair materials must be applied at the end of the 6 hours.

### Page 36

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 26 of 35
NOTE: Dependant on the shape of the disbond area it is acceptable if required, to carry out the repair by dividing
the area into several smaller sections. Each section can be laid next to each other and cured at the same
time.
(4) Apply OMat 2/30 Teflon tape over the surface area of the wire mesh facing sheet to the area that will be
pulled under vacuum. This will protect the facing sheet from overspill of adhesive and allow vacuum to be
pulled on the area where the honeycomb cells are slotted for drainage.
(5) Manufacture a support plate from a 4,00 mm (0.16 in.) rubber mat. The support plate should be at least
50,8 mm (2.0 in.) larger than the repair area. The support plate will be used to support the adhesive
compound.
C  Apply the epoxy paste to the repair area. Refer to Fig. 4 (B).
WARNING: BEFORE YOU USE CHEMICALS, READ, UNDERSTAND, AND OBEY ALL SAFETY
INSTRUCTIONS FOR THE CHEMICALS. THESE INSTRUCTIONS INCLUDE
INSTRUCTIONS FROM THE MANUFACTURER, THE MATERIAL SAFETY DATA
SHEET (MSDS), AND GOVERNMENT REGULATIONS. CHEMICALS MAY CAUSE
INJURY TO YOU OR MAKE YOU SICK WHEN SAFETY INSTRUCTIONS ARE NOT
OBEYED. AN MSDS GIVES INSTRUCTIONS ON HOW YOU MUST SAFELY USE,
KEEP, AND DISCARD CHEMICALS. GET INSTRUCTIONS FROM YOUR EMPLOYER
ON HOW YOU MUST SAFELY USE, KEEP AND DISCARD CHEMICALS.
(1) Use OMat 262 marker pen to mark the contour of the repair area on the rubber mat.
(2) Place a 6,35 mm (0.25 in.) high support around the edge of the marked area on the rubber mat. The support
can be made from a double row of OMat 2/110 Vacuum bag sealant tape. Stick the sealant tape to the
rubber mat and wrap OMat 2/30 Teflon tape around the sealant tape to avoid OMat 8/52 EA934NA Epoxy
paste adhesive sticking to the Vacuum bag sealant tape. Refer to Fig.4 (B).
(3) Mix the OMat 8/52 epoxy paste adhesive EA934NA for the honeycomb core in accordance with the
manufacturer’s instructions.
(4) Apply the OMat 8/52 epoxy paste adhesive EA934NA to the rubber mat with a clean metal spatula within
the support. Apply sufficient paste to get a maximum uniform thickness of 6,35 mm (0.25 in.).
(5) Allow the OMat 8/52 epoxy paste adhesive to cure for period of 2 hours 15 minutes at a room temperature
of 20 to 25 deg. C (68 to 77 deg. F.) until the adhesive becomes tacky. The time allowed for the adhesive to
become tacky will vary with temperature. Refer to the graph shown in Fig. 5.
(6) Monitor the adhesive regularly at high temperatures as the adhesive will begin to harden very quickly once it
has become tacky. As a guide use a pointed object to dip into the adhesive and lift upwards. If the adhesive
forms into a spike and the spike remains upright, the adhesive will be ready to invert.
(7) When the adhesive is tacky, remove the support from the boundary of the adhesive. Invert the rubber mat
with adhesive over the area to be closed, with the prepared compound surface towards the honeycomb cells.
Push the compound into the cells by lightly rolling on the back of the rubber mat using a roller.
(8) Make sure the surface of the rubber mat is flush with surface of the remaining facing sheet on the acoustic
liner.
NOTE:  It is important that the adhesive remains compact at the top of the honeycomb cells and does not run
towards the backing sheet.

### Page 37

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 27 of 35
D. Vacuum bagging procedure.
(1) Cut two sheets of OMat 2/111 Breather cloth, at least 25,4 mm. (1.0 in.) larger all around than the rubber
mat.
(2) Put the two sheets of breather cloth onto the rubber mat.
(3) Cut a sheet of OMat 2/31 Vacuum bag material, make sure that the vacuum bag has an overlap of
approximately 50,8 mm. (2.0 in.) around the breather cloth.
(4) Install the vacuum fitting to the vacuum bag in a position where it sits directly onto the top sheet of the
breather cloth.
(5) Attach and seal the vacuum bag to the panel with OMat 2/110 Tape, adhesive vacuum bag seal on the edge
of the OMat 2/30 Teflon tape.
(6) Use the vacuum pump to decrease the pressure in the repair area, making sure it gives an indication of at
least 635,0 mm. (25.0 in.) of mercury while the adhesive cures.
E. Cure the Adhesive
(1) Leave the adhesive to cure at room temperature 20 to 25 deg. C. (68 to 77 deg. F.) for 6 hours. This time can
vary with different room temperatures.
(2) After 6 hours remove the vacuum bagging materials and rubber mat. Final cure the adhesive using heat
lamps to cure the epoxy paste adhesive for 1 hour between 88 and 99 deg. C. (190 and 210 deg. F.).
(3) The rate of temperature increase and subsequent decrease must not be greater than 3 deg. C. (5.5 deg. F) per
minute.
(4) When the adhesive has fully cured allow the repair area to return to room temperature.
(5) Remove all traces of OMat 2/30 Teflon tape and excessive adhesive from the edges of the repair.
WARNING: WEAR PROTECTIVE CLOTHING, GLOVES, DUST MASK AND SAFETY GOGGLES.
WHEN ADHESIVE MATERIALS ARE CUT OR SANDED, DUST AND LOOSE
PARTICLES ARE PRODUCED WHICH ARE POTENTIAL HEALTH HAZARDS. DO
NOT BREATHE DUST
(6) Make the adhesive flush with the undamaged wire mesh adjacent to the repair area using OMat 5/31
abrasive paper. Refer to Fig. 6 (B).
WARNING: BEFORE YOU USE CHEMICALS, READ, UNDERSTAND, AND OBEY ALL SAFETY
INSTRUCTIONS FOR THE CHEMICALS. THESE INSTRUCTIONS INCLUDE
INSTRUCTIONS FROM THE MANUFACTURER, THE MATERIAL SAFETY DATA
SHEET (MSDS), AND GOVERNMENT REGULATIONS. CHEMICALS MAY CAUSE
INJURY TO YOU OR MAKE YOU SICK WHEN SAFETY INSTRUCTIONS ARE NOT
OBEYED. AN MSDS GIVES INSTRUCTIONS ON HOW YOU MUST SAFELY USE,
KEEP, AND DISCARD CHEMICALS. GET INSTRUCTIONS FROM YOUR EMPLOYER
ON HOW YOU MUST SAFELY USE, KEEP AND DISCARD CHEMICALS.
(7) Clean the damaged area with OMat 2/101 Lint free cloth moistened with solvent OMat 150 Acetone. Wipe
the area dry before the solvent evaporates. Wear OMat 2/114 Lint free gloves.

### Page 38

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 28 of 35
(8) Measure 25,4 mm (1.0 in.) around the edge of the damage for the carbon ply repair patch. Refer to Figure 6
sheet 1 view A.
(9) Apply OMat 2/30 Teflon tape from the edge of the area marked for the carbon ply over the surface area of the
wire mesh facing sheet that will be pulled under vacuum. This will allow vacuum to be pulled on the area
where the honeycomb cells are slotted for drainage. Refer to Fig.6 (A).
F. Cut the oversize ply
WARNING:  WEAR PROTECTIVE CLOTHING, GLOVES, DUST MASK AND SAFETY GOGGLES.
WHEN ADHESIVE MATERIALS ARE CUT OR SANDED, DUST AND LOOSE
PARTICLES ARE PRODUCED WHICH ARE POTENTIAL HEALTH HAZARDS. DO NOT
BREATHE DUST.
(1) Wear OMat 2/114 Lint free gloves and cut one piece of OMat 8/206A Carbon fibre fabric so that it has a
37,47 mm (1.5in) overlap all round the damage.
NOTE: To prevent fraying, cut the ply to the finished dimensions after it is soaked with adhesive.
G Prepare the repair materials
WARNING:  EA9390 ADHESIVE IS CLASSIFIED AS A HAZARDOUS MATERIAL, WHICH MAY
CAUSE INJURY OR ILLNESS IF NOT PROPERLY USED. THIS PRODUCT SHOULD BE
USED ONLY IN ACCORDANCE WITH THE MANUFACTURER’S SPECIFIC SAFETY
AND HEALTH RECOMMENDATIONS. PRIOR TO USE OF THIS PRODUCT,
CAREFULLY READ THE APPLICABLE “MATERIAL SAFETY DATA SHEET” AND
FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS.
(1) Mix the OMat 8/160 EA9390 Adhesive in accordance with the manufacturer’s instructions. The weight of
adhesive required will be approximately the same as the weight of the OMat 8/206A Carbon fibre fabric.
NOTE: After the ply has soaked, the remaining adhesive, if kept cool, can be used in the installation
procedure.
(2) Put the ply on a sheet of OMat 2/113 Non-porous parting film. Apply the adhesive to the two sides of the
ply with the OMat 212 Brush and cover the ply with another sheet of non-porous parting film.
(3) Use a roller to force the adhesive into the ply thoroughly.
(4) Let the two pieces of OMat 2/113 non-porous parting film stay on the ply until ready to use on the
installation procedure.
(5) Cut the ply so that it is larger by 25,4 mm (1.0 in.) all around the damage area. Make sure that the corners
have a minimum radius of 12,7 mm (0.5 in.).
(6) Keep the outer ply and the adhesive mixture cool until the installation procedure.
H Install the repair ply. Refer to Fig 6.
WARNING: EA9390 ADHESIVE IS CLASSIFIED AS A HAZARDOUS MATERIAL, WHICH MAY
CAUSE INJURY OR ILLNESS IF NOT PROPERLY USED. THIS PRODUCT SHOULD
BE USED ONLY IN ACCORDANCE WITH THE MANUFACTURER’S SPECIFIC
SAFETY AND HEALTH RECOMMENDATIONS. PRIOR TO USE OF THIS PRODUCT,
CAREFULLY READ THE APPLICABLE “MATERIAL SAFETY DATA SHEET” AND
FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS.
(1) Use an OMat 212 Brush to apply a layer of OMat 8/160 EA9390 Adhesive over the repair area.

### Page 39

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 29 of 35
(2) Remove one sheet of OMat 2/113 non-porous parting film from the repair ply. Put the repair ply with the
adhesive side on to the repair area. The repair ply must have an equal overlap all round the repair cut-out
and touch the OMat 2/30 Teflon tape.
(3) Use the roller to remove any air that is caught in the adhesive and to make the repair ply smooth.
(4) Remove any unwanted adhesive from the Teflon tape with a clean metal spatula.
(5) Remove the remaining OMat 2/113 non-porous film from the repair ply.
I. Install the vacuum bag and temperature probes.
(1) Put the temperature probes in position adjacent to the adhesive.
(2) Vacuum bagging procedure.
(a) Cut two sheets of OMat 2/111 Breather cloth, at least 25,4 mm. (1.0 in) larger all around than the
rubber mat.
(b) Put the two sheets of breather cloth onto the rubber mat.
(c) Cut a sheet of OMat 2/31 Vacuum bag material, make sure that the vacuum bag has an overlap of
approximately 50,8 mm. (2.0 in.) around the OMat 2/111 breather cloth.
(d) Install the vacuum fitting to the vacuum bag in a position where it sits directly onto the top sheet of
the OMat 2/111 breather cloth.
(e) Attach and seal the vacuum bag to the panel with OMat 2/110 Tape, Adhesive Vacuum bag seal on
the edge of the OMat 2/30 Teflon tape.
(f) Use the vacuum pump to decrease the pressure in the repair area, making sure it gives an indication
of at least 635,0 mm. (25.0 in) of mercury while the adhesive cures.
J.  Cure the adhesive
(1) Use a suitable heat lamp to keep the temperature of the repair area between 90 and 93 deg. C. (194 and
199 deg. F.) for 3 hours and 30 minutes until the adhesive is cured.
(2) The rate of temperature increase and subsequent decrease must not be faster than 3 deg. C. (5.5 deg. F.) in
each minute.
(3) When the adhesive has fully cured, remove the lamp, vacuum bagging materials, temperature probes and
the Teflon tape.
K. Make the edges of the Outer repair ply smooth
WARNING:  WEAR PROTECTIVE CLOTHING, GLOVES, DUST MASKS AND SAFETY GOGGLES.
WHEN ADHESIVE MATERIALS ARE CUT OR SANDED, DUST AND LOOSE
PARTICLES ARE PRODUCED WHICH ARE POTENTIAL HEALTH HAZARDS. DO
NOT BREATHE THE DUST.
CAUTION:  DO NOT CAUSE DAMAGE TO THE CARBON PLIES OF THE REPAIR AREA OR THE
OUTER SURFACE OF THE ACOUSTIC STRUCTURE. BE CAREFUL AND ONLY
REMOVE MATERIAL FROM THE EDGE OF THE REPAIR PLY. DO NOT USE A
LIQUID WITH THE ABRASIVE PAPER.
(1) Make the repair area smooth with OMat 5/31 Waterproof abrasive paper. Do not use any fluid with the
waterproof abrasive paper. There must not be a sharp edge between the repair ply and the acoustic panel
wire mesh.

### Page 40

Initial issue,07 March 2011
Revision 3, 05 December 2018 RB211-NAC-71-018
Page 30 of 35
L. Clean the repair area
(1) Remove all unwanted material from the repair area with a suction cleaner.
WARNING: BEFORE YOU USE CHEMICALS, READ, UNDERSTAND, AND OBEY ALL SAFETY
INSTRUCTIONS FOR THE CHEMICALS. THESE INSTRUCTIONS INCLUDE
INSTRUCTIONS FROM THE MANUFACTURER, THE MATERIAL SAFETY DATA SHEET
(MSDS), AND GOVERNMENT REGULATIONS. CHEMICALS MAY CAUSE INJURY TO
YOU OR MAKE YOU SICK WHEN SAFETY INSTRUCTIONS ARE NOT OBEYED. AN
MSDS GIVES INSTRUCTIONS ON HOW YOU MUST SAFELY USE, KEEP, AND DISCARD
CHEMICALS. GET INSTRUCTIONS FROM YOUR EMPLOYER ON HOW YOU MUST
SAFELY USE, KEEP AND DISCARD CHEMICALS.
(2) Clean the repair area with OMat 2/101 Lint free cloth moistened with solvent OMat 150 Acetone. Wipe the
repair area dry before the solvent evaporates. Wear OMat 2/114 Lint free gloves.
M. Make an inspection of the repair
(1) Do a visual inspection to make sure that the repair has been done in accordance with these procedures.
Carry out a tap test of the repair area in accordance with Structural Repair Manual 54-01-06, Tap Test.
Make sure the repair ply has a good bond. Make sure there are no air bubbles in the repair ply.
N. Identify the repair
(1) Vibro-etch the repair scheme number FRSZ030 to still allow onto the air intake cowl modification record
plate.

### Page 41 (OCR)

WIRE MESH AND CARBON FIBRE DISBOND (FACING SHEET)
FROM HONEYCOMB CORE
SECTION THROUGH ACOUSTIC PANEL
SHOWING TYPICAL DISBOND
ACOUSTIC PANEL
DAMAGED AREA  -TEFLON TAPE
MINIMUM RADIUS
12,7mm (0.5in)
LIPSKIN
TYPICAL VIEW OF REPAIR AREA
Idef0013294  B
Repair of Air Intake Cowl Acoustic Liner
Fig.3
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 31 of 35

### Page 42 (OCR)

DISBONDED FACING SHEET TRIMMED
DO NOT DAMAGE HONEYCOMB CORE
SECTION THROUGH DAMAGED
AREA SHOWING PLIES TO BE
REMOVED
TYPICAL LAY-UP BEFORE
ADDING ADHESIVE
Idef0013295  SECTION  A-A
Repair of Air Intake Cowl Acoustic Liner
Fig.4
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 32 of 35

### Page 43 (OCR)

195
180
TIME (minutes)  120
105
90
75
60
45
30
10  20  25  30  35  40
TEMP. deg. C
GRAPH SHOWING TIME TO GEL
AGAINST TEMPERATURE
Idef0013296
Graph for Curing Epoxy Paste
Fig.5
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 33 of 35

### Page 44 (OCR)

MARK 25,4 mm (1.0 in.)
CLEARANCE AROUND DAMAGE
DAMAGED AREA  ACOUSTIC PANEL
B
- TEFLON TAPE
MINIMUM RADIUS
LIPSKIN  12,7 mm (0.5 in.)
VIEW SHOWING AREA TO BE MASKED
EA934NA TO FILL  HONEYCOMB CORE BY  CARBON
6,35mm (0.25 in.)  REPAIR PLY  WIRE MESH
CARBON PLY
HONEY COMB  BACKING SKIN  rb211-nac-71-0018-01
CORE  SECTION
B-B
Repair of Air Intake Cowl Acoustic Liner- disbond between carbon ply and honeycomb core
Fig. 6
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 34 of 35

### Page 45 (OCR)

4.00  - 0,0700*0,000 Hole
-0.002
0.50  Handle
Adhesive®-
- 4.00 -
• Stem
0.062 in. dia piano wire
Use round head of tap hammer
only when you do the NDT  Pointed head of hammer not
required for self manufacture
- Head b
0.25
0.500
0.06R -
0.0700 +0.000  -0.002 Hole -  → 0.50 -  +0.25  0,09 R  0.25R
- 1.20 -
Note:  All dimensions in inches
Manufacture tap hammer
from mild steel or brass only
Tap hammer specifications.
Fig. 7
Initial issue, 07 March 2011  Revision 3, 05 December 2018  RB211-NAC-71-018
Page 35 of 35

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
