# Rolls-Royce Alert Non-Modification Service Bulletin RB.211-72-AJ165: RB.211-72-AJ165

- Rights: © Rolls-Royce plc. Filed by the FAA in regulations.gov docket FAA-2016-6692; AD 2016-24-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Rolls-Royce Alert Non-Modification Service Bulletin RB.211-72-AJ165](https://openairdocs.org/service-documents/rolls-royce/rb211-72-aj165.md)
- Title as filed: RB.211-72-AJ165
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/d4/b4/d4b4d2eaadd70daf46f07938117428814403d2ac8e1686f365cbdb2a8058dd5b
- Page: https://openairdocs.org/service-documents/rolls-royce/rb211-72-aj165/file/d4b4d2eaadd7

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

P.O. Box 31, DERBY
DE24 8BJ, UK  Rolls-Royce
Telephone: 44 (0) 1332 242424
Fax: 44 (0) 1332 249936  ROYCE
PUBLICATION  TRANSMITTAL
The technical information contained in this document has been approved under the authority
of - See Planning Information, Approval.
Date Mar. 31/16
RB211 TRENT 800 SERIES PROPULSION SYSTEMS NON-MODIFICATION SERVICE BULLETIN
Printed in Great Britain  This document transmits the Initial Issue of Service Bulletin RB211-72-AJ165  ALERT
Bulletin Initial Issue
Remove  Incorporate  Reason for change
Pages 1 to 12 of the  Initial Issue
Service Bulletin
ALERT  RB.211-72-AJ165
Transmittal - Page 1 of 2
CHECK THAT ALL PREVIOUS TRANSMITTALS HAVE BEEN INCORPORATED
If any have not been received please advise Customer Data Services, Rolls-Royce pic, Derby, England
© Rolls-Royce p/c (date as above) Printed in Great Britain

### Page 2 (OCR)

The effective pages to this Service Bulletin are as follows:
Revision Number Revision Date
Bulletin
1  Mar. 31/16  Printed in Great Britain
Mar. 31/16
Mar. 31/16
Mar. 31/16
Mar. 31/16
6  Mar. 31/16
Mar. 31/16
Mar. 31/16
Mar.31/16
10  Mar. 31/16
Mar. 31/16
Mar.31/16
RB.211-72-AJ165
Transmittal - Page 2

### Page 3 (OCR)

RB211 PROPULSION  SYSTEM
SERVICE
BULLETIN
POWERPLANT  - UPPER BIFURCATION FAIRING SEAL FACE INSPECTION - NON-MODIFICATION
SERVICE BULLETIN - MOD.72-AJ165
1. Planning Information
Printed in Great Britain  A. Effectivity
Boeing 777
RB211 TRENT 875-17 Engines
RB211 TRENT 877-17 Engines
RB211 TRENT 884-17 Engines
RB211 TRENT 884B-17 Engines
RB211 TRENT 892-17 Engines
RB211 TRENT 892B-17 Engines
RB211 TRENT 895-17 Engines
B. Reason
(1) Problem
A number of upper bifurcation fairings (EIPC 72-03-14, 07-250) (AIPC
72-03-14, 01-110) were found with titanium cracks located on the lower
part of the upper bifurcation fairing right seal face. These cracks were
found both in service and in overhaul shops. In some cases the cracks had
extended further and led to material release.
It is understood that the cracks initially propagate under low cycle
fatigue until vibration stresses become high enough to propagate under
(2) The safety intent of this Non-Modification Service Bulletin (NMSB) is to
prevent material loss of the fairing seal face and avoid a breach of the
fire wall.
C. Description
This NMSB instructs the repeat inspection of a specific zone of the upper
bifurcation fairing assembly. The inspection requires the use of a Non
Destructive Testing (NDT) method known as Fluorescent Penetrant Inspection
(FPI) to identify potential cracks in the lower part of the upper bifurcation
fairing right seal face.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 1 of 12
© Rolls-Royce p/c

### Page 4 (OCR)

•B211 SYSTEN  PROPULSION
SERVICE
BULLETIN
The inspection is to be carried out both on-wing and in-shop. If the on-wing
inspection fails, on-wing repair FRSJ739 can in some cases, be carried out to
avoid an upper bifurcation fairing replacement. The in-shop inspection can be
performed in an assembled condition if the fairing is not removed from the
Any rejected upper bifurcation fairings in-shop can be repaired to a  Printed in Great Britain
serviceable condition in accordance with Engine Manual TASK, 72-03-14, Examine
the upper bifurcation fairing (72-03-14, 07-250) and related parts.
If a fairing is found to have released titanium material, inform the local
Rolls-Royce Service representative.
D. Compliance
(1) ALERT
Part 1 - Initial Inspection on-wing and in-shop
(a) Carry out NSB initial inspection when the earliest of these following
conditions occur.
(i)  Inspect on-wing in accordance with Accomplishment Instruction
3.A prior to achieving 7,500 engine flight hours since the
upper bifurcation fairing was last inspected on-wing or
in-shop. If the time since last inspection exceeds 7,500 flight
hours at the issue date of this NMSB, inspect within the next
150 cycles from the issue date of this NMSB.
NOTE:  The last inspection could have been carried out in-shop in
accordance with Engine Manual TASK 72-03-14, Examine the
upper bifurcation fairing (72-03-14, 07-250) and related
parts. This Engine Manual inspection task is part of the
generic Engine Management Plan (EMP) for all engines going
through engine level refurbishment and overhaul shop
visits. The last inspection could also have been carried
out On-wing in accordance with Maintenance Planning Data
(MPD) document, inspection item number 72-390-01 (for left
engine) or 72-390-02 (for right engine).
(ii)  Inspect on-wing in accordance with Accomplishment Instruction
3.A when the engine maintenance schedule requires AMM TASK
72-03-14, upper bifurcation fairing inspection to be carried
out.
(iii)  Inspect in-shop in accordance with Accomplishment Instruction
3.B at next engine level check and repair, refurbishment or
overhaul (level 2, 3 or 4) shop visit. For those engines
currently in the shop, carry out inspection where the affected
part is exposed and substantial rebuild has not yet started.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 2
© Rolls-Royce p/c

### Page 5 (OCR)

RB211 SYS PULSION  SYSTEM
SERVICE
BULLETIN
(2) ALERT
Part 2 - Repeat Inspections
(a) On-wing
Printed in Great Britain  (ї)  Repeat at intervals not exceeding 7,500 engine flight hours
since last on-wing or in-shop inspection.
(b) In-shop
(ї)  Inspect at each engine level check and repair, refurbishment
and overhaul (level 2,3 and 4) shop visits.
(3) This Non-Modification Service Bulletin is anticipated to be the subject of
an EASA Airworthiness Directive.
E. Approval
The technical content of this Non-Modification Service Bulletin was approved
under the authority of Design Organisation Approval EASA.21J.035 on 24th March
2016.
F. Manpower
(1) On-wing
(a) Time to gain access - 15 mins (1 person).
(b) Time to inspect - 3 hours (1 person) - Personnel with NDT level 2
training are required to carry out FPI inspection.
(c) Time to repair if required - 8 hours (2 persons)
(d) Time to replace fairing if required - 30 hours (2 persons)
(2) In-shop
(a) Time to gain access - Not Applicable.
(b) Time to inspect - 2 hours (1 person) - Personnel with NDT level 2
training are required to carry out FPI inspection.
(c) Time to repair if required - Various depending on Engine Manual repair
carried out.
NOTE: The parts affected by this Non-Modification Service Bulletin
are accessible On-wing and In-shop.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 3
© Rolls-Royce pic

### Page 6 (OCR)

RB211 PASTEM SION  SYSTEM
SERVICE
BULLETIN
G. Material Price and Availability
Material price and availability is on request via your assigned Rolls-Royce
airline support team or Rolls-Royce overhaul support team.
H. Tooling Price and Availability  None.  Printed in Great Britain
1. References
(1) Engine Manual
(a) TASK, 72-03-00, Remove the Upper Bifurcation Fairing.
(b) TASK, 72-03-00, Install the Upper Bifurcation Fairing.
(c) TASK, 72-03-14, Examine the Upper Bifurcation Fairing.
(d) TASK, 72-00-00, Overhaul Process 210 - Fluorescent Penetrant
Inspection.
(2) Aircraft Maintenance Manual
(a) TASK, 27-81-00, Retract the Leading Edge Slats.
(b) TASK, 27-81-00, Leading Edge Slat Deactivation.
(c) TASK, 27-81-00, Leading Edge Slat Reactivation.
(d) TASK, 78-31-00, Thrust Reverser Deactivation for Ground Maintenance.
(e) TASK, 78-31-00, Thrust Reverser Activation after Ground Maintenance.
(f) TASK, 71-11-04, Open the Fan Cowl Panel (Selection).
(g) TASK, 71-11-04, Close the Fan Cowl Panel (Selection).
(h) TASK, 78-31-00, Open the Thrust Reverser (Selection).
(i) TASK, 78-31-00, Close the Thrust reverser (Selection).
(j) TASK, 72-03-14, Upper Bifurcation Fairing Removal.
(k) TASK, 72-03-14, Upper Bifurcation Fairing Installation.
(L) TASK, 72-03-14, Upper Bifurcation Fairing Inspection.
(m) TASK, 70-20-02, Water - Washable Fluorescent Penetrant Inspection
(Maintenance Process 213).
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 4
© Rolls-Royce pic

### Page 7 (OCR)

RB211 PROPULSION  SYSTEM
SERVICE
OYCE  BULLETIN
2. Material Information
A. Consumable materials required for the On-wing FPI inspection
Printed in Great Britain  Reference  Description  Specification
B00668 (OMat 101)  Kerosene  OMat 101
G00034  Cotton Wiper - Process  BMS15-5, Class A
Cleaning Absorbent
Wiper (Cheesecloth,
Gauze)
G02383 (OMat 2/101)  Cloth - Absorbent, Lint  OMat 2/101
free
G02384 (OMat 606A)  Developer  - Powder -  OMat 606A
Ardrox  : 9D4A
G02385 (OMat 616)  Remover - Solvent  919 7ewo
Penetrant
G02386 (OMat 621A)  Remover - Fluorescent
Penetrant (Hydrophilic)
- Ardrox 9PR12
G02397 (OMat 617)  Developer - Non-Aqueous  219 7eWo
Aerosol
G02401 (OMat 653)  Penetrant -  ESO FeWO
Fluorescent, Medium
Sensitivity Water
Washable
G02400 (OMat 632)  Penetrant -  OMat 632
Fluorescsent, High
Sensitivity water
Washable
If the repair FRSJ739 is to be carried out, the part below is required.
Part Number  Description  Qty
KH67157  Bracket  1
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 5
© Rolls-Royce p/c

### Page 8 (OCR)

RB211 SYSTEM  PROPULSION
SERVICE
BULLETIN
3. Accomplishment Instructions
A. On-wing
For this procedure the upper bifurcation fairing will be referred to as the
fairing. You must open the thrust reversers to get access to the fairing.
WARNING: YOU MUST BE CAREFUL WHEN YOU WORK ON THE ENGINE AFTER THE ENGINE IS  Printed in Great Britain
SHUTDOWN. THE ENGINE CAN STAY HOT FOR ALMOST ONE HOUR.
WARNING:  YOU MUST NOT TOUCH HOT PARTS WITHOUT APPLICABLE GLOVES. HOT PARTS CAN
CAUSE INJURY.  IF YOU GET AN INJURY, PUT IT IN COLD WATER FOR 10
MINUTES. THEN GET MEDICAL AID.
CAUTION:  IN ORDER TO REDUCE THE POTENTIAL FOR MULTIPLE-ENGINE IN-FLIGHT SHUTDOWN,
POWER LOSS, OR OTHER ANOMALY DUE TO MAINTENANCE ERROR, ROLLS-ROYCE
RECOMMENDS  THAT OPERATORS AVOID PERFORMING MAINTENANCE ON MULTIPLE
ENGINES INSTALLED ON THE SAME AIRCRAFT AT THE SAME TIME. IF IT IS NOT
POSSIBLE TO AVOID MAINTENANCE ON MORE THAN ONE ENGINE AT THE SAME TIME,
ROLLS-ROYCE RECOMMENDS THAT ADDITIONAL CONTROLS ARE APPLIED IN ORDER TO
MAKE SURE THAT MAINTENANCE TASKS HAVE BEEN COMPLETED AS DEFINED.
MAINTENANCE GUIDELINES SHOULD BE REVISED, WHERE POSSIBLE, TO PROMOTE
THIS RECOMMENDATION
(1) Gain access.
(a) Do these tasks in sequence to safely open the left and right thrust
reversers on the applicable engine:
(i)  Do this AMM TASK: Retract the Leading Edge Slats, TASK
27-81-00.
(ii)  Do this AMM TASK: Leading Edge Slat Deactivation, TASK
27-81-00.
(iii) Do this AMM TASK: Thrust Reverser Deactivation for Ground
Maintenance, TASK 78-31-00.
(iv)  For the left and right fan cowl panels, do this AMM TASK: Open
the Fan Cowl Panel (Selection), 71-11-04.
Number Name/Location
413AL Left Fan Cowl Panel, Left Engine
414AR Right Fan Cowl Panel, Left Engine
423AL Left Fan Cowl Panel, Right Engine
424AR Right Fan Cowl Panel, Right Engine
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 6
© Rolls-Royce pic

### Page 9 (OCR)

RB211 PASPEL SION  SYSTEM
SERVICE
BULLETIN
(v)  For the left and right thrust reversers, do this AMM TASK: Open
the Thrust reverser (Selection), TASK 78-31-00.
Number Name/Location
Printed in Great Britain  416AR Right Thrust Reverser, Left Engine  415AL Left Thrust Reverser, Left Engine
425AL Left Thrust Reverser, Right Engine
426AR Right Thrust Reverser, Right Engine
(b) Install the protective mat, SPL-13999 into the LP compressor rear
case. Make sure that the red warning flag can be seen from the ground.
(2) Examine the fairing. Refer to Fig.1 and Fig.2.
(a) Visually examine the fairing for any titanium cracks or material loss
on the right hand side fairing seal face 22 and the right hand side
seal support 23. Pay particular attention towards the lower part of
the fairing and especially in Zone A.
(ї)  If the titanium seal face 22 is found to have released
material, replace the fairing in accordance with AMM TASK
72-03-14, Upper Bifurcation Fairing Removal/Installation.
(ii)  If more than one crack is found, replace the fairing within 15
engine flight cycles in accordance with AMM TASK 72-03-14,
Upper Bifurcation Fairing Removal/Installation.
(iii)  If material loss or one crack is found on the seal support 23,
replace the fairing within 15 flight cycles in accordance with
AMM TASK 72-03-14, Upper Bifurcation Fairing
Removal/Installation.
(iv)  If there is a single crack on the lower right hand side of the
fairing seal face 22, do the following:
(1) If the crack is shorter than 6mm, repair (refer to FRSJ739)
or replace the fairing (refer to AMM TASK 72-03-14, Upper
Bifurcation Fairing Removal/Installation) within 100 engine
flight cycles.
(2)  If the crack is longer than 6mm, repair (refer to FRSJ739) or
replace the fairing (refer to AMM TASK 72-03-14, Upper
Bifurcation Fairing Removal/Installation) within 15 engine
flight cycles.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 7
© Rolls-Royce p/c

### Page 10 (OCR)

RB211 SYSTEM  PROPULSION
SERVICE
BULLETIN
(b) If the visual inspection does not detect any crack, carry out a crack
test in zone A (refer to Fig.1). Refer to AMM TASK 70-20-02, Water
Washable Fluorescent Penetrant Inspection (Maintenance Process 213).
NOTE: NDT Level 3 personnel can approve a change to the
penetrant OMat 632.  classification of the penetrant to the high sensitivity  Printed in Great Britain
(і)  If a crack shorter than 6mm is detected during the crack test
inspection, repair (refer to FRSJ739) or replace the fairing
(refer to AMM TASK 72-03-14, Upper Bifurcation Fairing
Removal/Installation) within 100 engine flight cycles.
(ii) If a crack longer than 6mm is detected during the crack test
inspection, repair (refer to FRSJ739) or replace the fairing
(refer to AMM TASK 72-03-14, Upper Bifurcation Fairing
Removal/Installation) within 15 engine flight cycles.
(3) Close up
(a) Return the engine to a serviceable condition.
CAUTION: MAKE SURE THAT YOU REMOVE ALL TOOLS, LOOSE PARTS AND
UNWANTED MATERIAL FROM THE AREA WHEN YOU COMPLETE
MAINTENANCE. DAMAGE TO EQUIPMENT COULD OCCUR.
(і)  Remove the protective mat, SPL-13999 from the rear compressor
case.
WARNING: DO ALL OF THE SPECIFIED TASKS IN THE CORRECT SEQUENCE TO
CLOSE THE THRUST REVERSERS. IF YOU DO NOT OBEY THIS
INSTRUCTION, INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT
CAN OCCUR
(ії)  Do these tasks in sequence to safely close the left and right
thrust reversers on the applicable engine:
(1) Do this AMM TASK: Close the Thrust Reverser (Selection), TASK
78-31-00.
Number Name/Location
415AL Left Thrust Reverser, Left Engine
416AR Right Thrust Reverser, Left Engine
425AL Left Thrust Reverser, Right Engine
426AR Right Thrust Reverser, Right Engine
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 8
© Rolls-Royce pic

### Page 11 (OCR)

RB211 PRSTEMSION  SYSTEM
SERVICE
BULLETIN
Do this AMM TASK: Close the Fan Cowl Panel (Selection), TASK
71-11-04.
Number Name/Location
Printed in Great Britain  413AL Left Fan Cowl Panel, Left Engine  414AR Right Fan Cowl Panel, Left Engine
423AL Left Fan Cowl Panel, Right Engine
424AR Right Fan Cowl Panel, Right Engine
(3) Do this AMM task: Thrust Reverser Activation after Ground
Maintenance, TASK 78-31-00.
(4) Do this AMM task: Leading Edge Slat Reactivation, TASK
27-81-00.
(4)  Record of accomplishment of this Non-Modification Service Bulletin is
required in accordance with local Service Bulletin tracking system
procedures.
B. In-Shop
(1) Examine the fairing. Refer to Fig.1 and Fig.3.
NOTE: Inspection can be done in the assembled condition if the
fairing was not removed from the engine. If it is required to
remove the fairing from the engine for repair purposes, refer
to EM TASK 72-03-00, Remove the upper bifurcation fairing.
(a) Visually examine for any titanium cracks or material loss on the right
hand side fairing seal face 22 and the right hand side seal support
23. Pay particular attention towards the lower part of the fairing and
especially in zone A.
(і)  If the titanium seal face 22 or seal support 23 is found to
have released material, repair or replace the fairing.
(її)  If the titanium seal face 22 or seal support 23 is found with a
crack, repair or replace the fairing.
(b) If the visual inspection does not detect any crack, do a local
penetrant crack test in zone A, refer to EM 70-00-00, Overhaul Process
210 - Fluorescent Penetrant Inspection.
(ї)  If any crack is found, repair or replace the fairing.
Record of accomplishment of this Non-Modification Service Bulletin is
required in the engine log book.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 9
© Rolls-Royce pic

### Page 12 (OCR)

ROLLS  RB211 PYSPEMSION
R  SERVICE  SYSTEM
ROYCE  BULLETIN
22 UPPER  Printed in Great Britain
BIFURCATION
21 UPPER  - FAIRING
BIFURCATION  SEAL FACES
OUTER SKIN
23 SEAL
• SUPPORT
1.57 in
(40.0 mm)
0.79 in
(20.0 mm)
LEGEND:
ZONE A
def0017666
Upper Bifurcation Fairing - Inspection location
Fig.1.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 10
© Rolls-Royce plc

### Page 13 (OCR)

B211 SYSTEN  PROPULSIOI
SERVICE
BULLETIN
Printed in Great Britain  METHOD:
VISUAL
INSPECTION
SUPPORT  OF SEAL  MATERIAL  YES  REPLACE  INFORM  ROLLS-
AND  LOSS?  FAIRING  ROYCE
SEAL FACE
NO
METHOD:  VISIBLE  YES  MULTIPLE  YES  FLY-ON  FOR  REPLACE
VISUAL  CRACK?  CRACKS?  15 CYCLES  FAIRING
NO  NO
MATERIAL LOSS ON  CRACK OR  YES
SEAL SUPPORT?
NO
NDT
METHOD:  FPI  INSPECTION  ON SEAL  FACE  CRACK?  YES  SEAL FACE  CRACK ON  >6 mm?  YES  15 CYCLES  FLY-ON  FOR
NO  NO  REPAIR
OR
REPLACE
FAIRING
FLY-ON
CONTINUE  FOR
OPERATION  100 CYCLES
L  def0017667
Flow Chart of the On-wing Inspection
Fig.2.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 11
© Rolls-Royce p/c

### Page 14 (OCR)

RB211 PYSPEMSION  SYSTEM
SERVICE
ROYCE  BULLETIN
METHOD:  Printed in Great Britain
VISUAL
INSPECTION  REPAIR
SUPPORT  OF SEAL  AND  MATERIAL  LOSS?  YES  REPLACE  FAIRING  OR  INFORM  ROLLS-  ROYCE
SEAL FACE
NO
REPAIR
METHOD:  VISIBLE  YES  CRACK ON  YES  OR
VISUAL  CRACK?  SEAL  REPLACE
FACE?  FAIRING
NO  NO
REPAIR
CRACK ON  YES  OR
SEAL  REPLACE
SUPPORT?  FAIRING
NO
REPAIR
METHOD:  FPI  INSPECTION  IN ZONE A  NDT  CRACK?  YES  REPLACE  FAIRING  OR
NO
ACCEPT
L  def0017669
Flow Chart of the In-shop Inspection
Fig. 3.
Mar. 31/16  RB.211-72-AJ165
Mar. 31/16  Page 12
© Rolls-Royce plc

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
