# Saab Service Bulletin 2000-22-008: No revision named

- Rights: © Saab. Filed by the FAA in regulations.gov docket FAA-2018-1067; AD 2019-10-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Saab Service Bulletin 2000-22-008](https://openairdocs.org/service-documents/saab/sb-2000-22-008.md)
- Title as filed: sb2000_22_008_00
- Pages: 42
- PDF: https://openairdocs.org/files/sha256/7a/4c/7a4c6bd8770436f203e579059d20b7a47b099bcdb813c5eae9e5cdd9ac52a416
- Page: https://openairdocs.org/service-documents/saab/sb-2000-22-008/file/7a4c6bd87704

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin
15 June 2018
 
2000−22−008
Page 1 of 42
ATA CHAPTER: 22
AUTO FLIGHT − AUTO PILOT − MODIFICATION OF THE AUTO PILOT DISCONNECT
LOGIC
Mod No. 6566
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Aircraft:
Aircraft Mfg. Serial No’s SAAB 2000 − 004 thru − 063.
NOTE: FOR A/C 004 −009 Service Bulletin SAAB 2000−91−001 must be included before this
Service Bulletin.
(2) Spares: Not affected.
B. REASON
Due to an inflight event causing a serious situation, the auto pilot disengage logic is modified to
disengage the auto pilot when either of the two main pitch trim switches on each control wheel are
operated.
C. DESCRIPTION
This Service Bulletin gives instructions for:
− removal of relays
− installation of new wires
− Relocation of wires
− installation of relays
D. COMPLIANCE
Mandatory.
Saab recommends this Service Bulletin to be performed within 24 months or 3000 FH, whichever
comes first, from release of this Service Bulletin.
This Service Bulletin is under EASA consideration for an Airworthiness Directive.
The final compliance terms will be set by the EASA Airworthiness Directive (AD) when issued.
E. APPROVAL
The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21J.066.
F. MANPOWER
Estimated time to complete this Service Bulletin is:
1 person required.
Total manhours: 12
Elapsed time (hours): 12
Labour cost at operators expense.

### Page 2

Service Bulletin
15 June 2018
 
2000−22−008
Page 2 of 42
G. MATERIAL − COST AND AVAILABILITY
Price and availability for Mod Kit. No. SAAB 2000−22−008−01 will be furnished on request.
H. TOOLING
Air-data Test Set - Collins 970D-2A or equivalent
Crimp tool Positioner Insert tool Removal tool Used for
M22520/1−01 TH343 M81969/14−02 M81969/14−02 RSD20
GMT232 − − − S2420
I. WEIGHT AND BALANCE
None.
J. ELECTRICAL LOAD DATA
Not affected.
K. REFERENCES
Aircraft Maintenance Manual (AMM) TASK 24−00−00−860−801
TASK 24−00−00−860−802
TASK 27−32−00−710−801
TASK 31−15−10−000−801
TASK 31−15−10−400−801
L. OTHER PUBLICATIONS AFFECTED
Aircraft Maintenance Manual (AMM)
Wiring Diagram Manual (WDM)
System Schematics Manual (SSM)
Aircraft Operations Manual (AOM)
2. ACCOMPLISHMENT INSTRUCTIONS
A. JOB SET −UP
(1) Before you start the SB, make sure:
− The modification kit contains the parts listed in the Service Bulletin
− The local supply items listed in the Service Bulletin are available
− The documentation is available
− The special tools are available.
B. REMOVAL
(1) Remove the following access panels.
− 117AL
− 117AZ
− 118AR
− 220AZ
(2) Remove the relays (Ref AMM TASK 31−15−10−000−801).

### Page 3

Service Bulletin
15 June 2018
 
2000−22−008
Page 3 of 42
REF. FIG. 1
(a) In the LH electrical center 305VU, remove the relays:
− 35CC
− 37CC
FOR A/C 004−019
(b) In the RH electrical center 306VU, remove the relays:
− 34CC
− 36CC
− 16FD
FOR A/C 020−063
(c) In the RH electrical center 306VU, remove the relays:
− 34CC
− 36CC
FOR A/C 004−019
C. MODIFICATION
(1) Wiring modification.
REF. FIG. 1, 2, 3, 5, 6
(a) In the LH electrical center 305VU, install the following new wire:
Wire No Class From Contact To Contact Remarks
CC3000−24 A 35CC−J1:A2 RSD20 37CC−J1:B3 RSD20
(b) In the RH electrical center 306VU, relocate the following wire:
Wire No Class From Contact To Contact Remarks
FD38−24 A 16FD−J1:X1 − 306VS−AP S2420 Connect to-
gether with
wire CC3004
(c) In the RH electrical center 306VU, install the following new wires:
Wire No Class From Contact To Contact Remarks
CC3002−24 A 34CC−J1:C3 RSD20 36CC−J1:C2 RSD20
FD3000−24 A 16FD−J1:X1 RSD20 34CC−J1:C2 RSD20
(d) Install the following new wires between the LH electrical center 305VU and RH electrical
center 306VU:
Wire No Class From Contact To Contact Remarks
CC3001−24 A 37CC−J1:B2 RSD20 36CC−J1:C3 RSD20
CC3004−24 A 35CC−J1:A3 RSD20 306VS−AP Connect to-
gether with
wire FD38
FOR A/C 020−063
D. MODIFICATION
(1) Wiring modification.

### Page 4

Service Bulletin
15 June 2018
 
2000−22−008
Page 4 of 42
REF. FIG. 1, 4, 7
(a) In the LH electrical center 305VU, relocate the following wire:
Wire No Class From Contact To Contact Remarks
CC726−24 A 305VS−HW − 305VS−PB S2420 Connect to-
gether with
wire CC3000
(b) In the LH electrical center 305VU, install the following new wires:
Wire No Class From Contact To Contact Remarks
CC3000−24 A 35CC−J1:A3 RSD20 305VS−PB Connect to-
gether with
wire CC726
CC3001−24 A 35CC−J1:A2 RSD20 37CC−J1:B3 RSD20
(c) In the RH electrical center 306VU, install the following new wire:
Wire No Class From Contact To Contact Remarks
CC3004−24 A 34CC−J1:C3 RSD20 36CC−J1:C2 RSD20
(d) Install the following new wires between the LH electrical center 305VU and RH electrical
center 306VU:
Wire No Class From Contact To Contact Remarks
CC3002−24 A 36CC−J1:C3 RSD20 37CC−J1:B2 RSD20
CC3005−24 A 34CC−J1:C2 RSD20 305VS−HW S2420 Connect to-
gether with
wire
FD435,
FD436,
FD437
FOR A/C 004−063
E. INSTALLATION
(1) Install the relays (Ref AMM TASK 31−15−10−400−801):
REF. FIG. 1
(a) In the LH electrical center 305VU, install the relays:
− 35CC
− 37CC
FOR A/C 004−019
(b) In the RH electrical center 306VU, install the relays:
− 34CC
− 36CC
− 16FD
FOR A/C 020−063
(c) In the RH electrical center 306VU, install the relays:
− 34CC
− 36CC

### Page 5

Service Bulletin
15 June 2018
 
2000−22−008
Page 5 of 42
FOR A/C 004−063
F. FUNCTIONAL TEST
(1) Connect the Air-data Test Set to the LH and the RH Air Data Computers (ADCs).
(2) Supply the External AC Power (Ref. AMM TASK 24−00−00−860−801)
(a) Supply the External AC Power (Ref. AMM TASK 24−00−00−860−801)
(b) On the overhead panel ELEC DC PWR (24VU), push in these pushswitches:
− L AVION
− R AVION
− ESS AVION
(3) For AHRS equipped aircraft, make sure the AHRS aligns.
(4) For IRS equipped aircraft, align the IRS.
(a) On the overhead panel EFIS SOURCE (65VU), make sure the EFIS SOURCE/IRS switch
is set to NORM.
(b) On the overhead panel L WIPER/AVIONIC (47VU), set the IRS1/OFF/NAV/ATT switch to
NAV.
(c) On the overhead panel R WIPER/AVIONIC (14VU), set the IRS2/OFF/NAV/ATT switch to
NAV.
(5) On the ADS test set, increase the altitude until the LH and RH PFDs shows 5000ft.
(6) On the ADS test set, increase the Indicated Air Speed (IAS) until the LH and RH PFDs shows
120 knots.
(7) Do the functional test of the autopilot.
NOTE: You must not start this test until the AHRS/IRS aligns. Make sure the ATT/HDG
ALIGNING - DO NOT TAXI message goes off and the normal attitude indicator is
shown on both PFDs.
ACTION RESULT
(a) On the Flight Control Panel
(FCP), turn the altitude preselect
knob and set an altitude that is
different from the aircraft
altitude.
On the PFD, make sure the preselected
altitude is not set to the aircraft altitude.
(b) Push the /C0065 1 2 /C0034 pushbutton
and set it to the /C0065 (FD 1)
position
On the two PFD.s:
− The FD V bar is shown (On the DCP
operate the FD pushbutton and make
sure the FD V bar is not set to off)
− The white AP <- legend is shown.
(c) Push the VS and the HDG
pushbuttons.
On the FCP, the two indicators above the
VS and the HDG pushbuttons come on.
On the PFDs, the green VS, the white
ALTS and the green HDG legends are
shown.

### Page 6

Service Bulletin
15 June 2018
 
2000−22−008
Page 6 of 42
ACTION RESULT
(d) Push each of the mode-select
pushbuttons (but not the HALF
BANK and the VNAV
pushbuttons) in sequence and
make sure the result is
satisfactory before you continue.
The applicable legends are shown in the
same sequence on the PFDs.
The indicators above the mode-select
pushbuttons come on.
It is not possible to set more than one
lateral and one vertical mode at the same
time (although it is possible to do this with
the modes that have arm logic).
A second push of the mode-select
pushbutton does not cancel the mode (this
shows the select logic operates correctly)
(e) Push the HALF BANK
pushbutton two times.
The first push sets the half bank mode and
the indicators above the HALF BANK
pushbutton come on.
The second push cancels the half bank
mode.
(f) Push the VNAV pushbutton two
times
The first push sets the VNAV mode and
the indicators above the VNAV pushbutton
come on.
On the PFDs, the NO VNAV legend is
shown.
The second push cancels the VNAV
mode.
(g) Turn the HDG/PUSH SYNC
control to set the heading bug
(shown on the PFDs) to 45/C0095 to
the right.
On the PFDs, the FD V-bar shows the
right bank command.
(h) Push the HDG/PUSH SYNC
knob.
The heading shown with the heading bug
and the aircraft heading align. The FD
V-bar shows the wings level.
(i) Turn the HDG/PUSH SYNC
control to set the heading bug to
45/C0095 to the left.
The FD V-bar shows the left bank
command.
(j) Push the HDG/PUSH SYNC
knob.
The heading shown with the heading bug
and the aircraft heading align.
The FD V-bar shows the wings level
command.
(k) Push the IAS/M pushbutton. The IAS mode legend is shown on the
PFDs and the IAS and the aircraft speed
align.
(l) Turn the IAS/M knob to
decrease the IAS reference
speed 20 knots.
The IAS reference speed decreases 20
knots.
The FD V-bar shows the up command.

### Page 7

Service Bulletin
15 June 2018
 
2000−22−008
Page 7 of 42
ACTION RESULT
(m) On the pilots control wheel, push
the VERT SYNC pushbutton.
The IAS reference speed and the aircraft
speed align. The FD V-bar shows the
wings level.
(n) On the FCP, turn the IAS/M knob
to increase the IAS/M reference
speed 20 knots.
The IAS reference speed increases 20
knots.
The FD V-bar shows the down command.
(o) On the copilots control wheel,
push the VERT SYNC
pushbutton.
The IAS reference speed and the aircraft
speed align. The FD V-bar shows the
wings level.
(p) On the FCP, push the VS
pushbutton.
The VS mode legend comes on and the
VS reference is shown.
(q) Use the VS, /C0089 DN /C0066 UP, rocker
switch and change the VS
reference to show a 1000 feet
per minute climb.
The VS reference changes and the FD
V-bar show the up command.
(r) Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0034 (FD 2)
position.
There is no change to the VS mode
legend and the VS
The white AP -> legend is shown on the
PFDs
(s) Use the VS, /C0089 DN /C0066 UP,
rocker switch and change the VS
reference to show a 1000 feet
per minute descent.
The VS reference changes and the FD
V-bar show the down command.
(t) Turn the ALTS PUSH/CANCEL
control to set the preselected
altitude to 6000 ft.
The preselected altitude of 6000 ft. is
shown.
(u) Push the LVL CHG pushbutton. The CLIMB mode legend is shown on the
PFDs.
(v) Push the ALT pushbutton. The ALT legend is shown on the PFDs.
(w) Turn the ALTS PUSH/CANCEL
control to change the
preselected altitude to 4000 ft.
The preselected altitude of 4000 ft. is
shown on the PFDs.
(x) Push the LVL CHG pushbutton. The DESCENT mode legend is shown on
the PFDs.
(y) On the Autopilot Panel (APP),
turn the /C0089 DN /C0066 UP wheel to
give a pitch up command.
The VS mode legend is shown on the
PFDs.
The VS reference goes to a positive value
in proportion to the quantity you move the 
/C0089 DN /C0066 UP wheel.
(z) On the Autopilot Panel (APP),
turn the /C0089 DN /C0066 UP wheel
forwards to give a pitch down
command.
The VS reference goes to a negative value
in proportion to the quantity you turn the 
/C0089 DN /C0066 UP wheel.

### Page 8

Service Bulletin
15 June 2018
 
2000−22−008
Page 8 of 42
ACTION RESULT
(aa) On the ADS test set, decrease
the Indicated Air Speed (IAS)
until the LH and RH PFDs shows
below 40 knots.
(ab) Pressurize the Hydraulic System
with the Standby Pumps (Ref.
TASK 29-10-00-860-801)
(ac) On the overhead panel TEST 3,
set the L ELEVATOR and the R
ELEVATOR switch to the top
position to initialize the MBIT.
After 10 to 15 seconds, make sure that no
warnings are shown for the Elevator
Control System.
(ad) On the overhead panel TEST 2,
momentarily operate the
RUDDER switch to the top
position to initialize the Rudder
Control System PBIT test.
After 10 to 15 seconds, make sure that no
warnings are shown for the Rudder
Control System.
(ae) Lift the YD and the AP levers. The levers stay engaged and the green
AP -> legend is shown on the PFDs.
(af) On the Autopilot Panel (APP),
push the TURB pushbutton.
In the TURB pushbutton, the indicator light
comes on.
(ag) Push the TURB pushbutton a
second time.
In the TURB pushbutton, the indicator light
goes off.
(ah) On the pilots control wheel, push
the AP DISCONNECT
pushbutton
The autopilot disengages and the cavalry
charge audio warning is heard.
The red AP -> legend is shown on the
PFDs.
(ai) Push the AP DISCONNECT
pushbutton a second time.
The cavalry charge audio warning stops.
The red AP -> legend changes to white.
(aj) On the APP, lift the AP lever. The autopilot engages.
(ak) On the copilots control wheel,
push the AP DISCONNECT
pushbutton
The autopilot disengages and the cavalry
charge audio warning is heard.
The red AP -> legend is shown on the
PFDs.
(al) Push the AP DISCONNECT
pushbutton a second time.
The cavalry charge audio warning stops.
The red AP -> legend changes to white.
(am)On the APP, lift the AP lever. The autopilot engages.
(an) On the control quadrant, on the
aft of the LH POWER lever,
push the go-around palm switch.
The autopilot disengages and the cavalry
charge audio warning is heard.
On the PFDs, the GA mode legend is
shown and the Flight Director (FD) shows
the pitch up command.
(ao) Push the go-around palm switch
a second time.
The cavalry charge audio warning stops.

### Page 9

Service Bulletin
15 June 2018
 
2000−22−008
Page 9 of 42
ACTION RESULT
(ap) On the APP, lift the AP lever. The autopilot engages.
(aq) On the control quadrant, on the
aft of the RH POWER lever,
push the go-around palm switch.
The autopilot disengages and the cavalry
charge audio warning is heard.
On the PFDs, the GA mode legend is
shown and the Flight Director (FD) shows
the pitch up command.
(ar) Push the go-around palm switch
a second time.
The cavalry charge audio warning stops.
(as) On the APP, lift the AP lever. The autopilot engages.
(at) On the pilots control wheel, hold
the two main pitch trim switches
in the down position.
The autopilot disengages and the cavalry
charge audio warning is heard.
(au) On the pilots control wheel, push
the AP DISCONNECT
pushbutton.
The cavalry charge audio warning goes
off.
(av) On the APP, lift the AP lever. The autopilot engages.
(aw) On the pilots control wheel, hold
the two main pitch trim switches
in the up position.
The autopilot disengages and the cavalry
charge audio warning is heard.
(ax) On the pilots control wheel, push
the AP DISCONNECT
pushbutton.
The cavalry charge audio warning goes
off.
(ay) On the APP, lift the AP lever. The autopilot engages.
(az) On the copilots control wheel,
hold the two main pitch trim
switches in the down position.
The autopilot disengages and the cavalry
charge audio warning is heard
(ba) On the copilots control wheel,
push the AP DISCONNECT
pushbutton.
The cavalry charge audio warning goes
off.
(bb) On the APP, lift the AP lever. The autopilot engages.
(bc) On the copilots control wheel,
hold the two main pitch trim
switches in the up position.
The autopilot disengages and the cavalry
charge audio warning is heard
(bd) On the copilots control wheel,
push the AP DISCONNECT
pushbutton.
The cavalry charge audio warning goes
off.
(be) On the APP, lift the AP lever. The autopilot engages.
(bf) On the trim panel 45VU, operate
the standby pitch trim switch in
the two directions.
The autopilot disengages and the cavalry
charge audio warning is heard
(bg) On the APP, lift the AP lever. The autopilot engages.

### Page 10

Service Bulletin
15 June 2018
 
2000−22−008
Page 10 of 42
ACTION RESULT
(bh) On the FCP, push the HDG
pushbutton and try to move the
pilots control column.
The autopilot holds the control column in
position.
(bi) On the APP turn the /C0089 DN  /C0066
UP wheel in different quantities
forwards and then rearward.
The control column moves forwards and
then rearward in proportion to the quantity
you move the /C0089 DN /C0066 UP wheel.
(bj) Turn the L /C0065 /C0034 R knob to the
left and to the right in different
quantities.
The control wheel moves to the left and
then to the right in proportion to the
quantity you move the L /C0065 /C0034 R knob.
(bk) At the same time:
− Hold the control column in
position
− Turn the /C0089 DN /C0066 UP wheel
forwards until the FD V-bar on
the PFD shows a down
command.
On the PFDs the yellow P legend comes
on after approximately 5 seconds (this
shows an elevator mistrim condition). On
the Primary EICAS Display (PED), the
amber AP PITCH MISTRIM legend comes
on after approximately 10 seconds.
(bl) Release the control column.
(bm)At the same time:
− Hold the control column in
position
− Turn the /C0089 DN /C0066 UP wheel
rearwards until the FD V-bar
on the PFD shows the up
command.
On the PFDs the yellow P legend comes
on after approximately 5 seconds (this
shows an elevator mistrim condition). On
the Primary EICAS Display (PED), the
amber AP PITCH MISTRIM legend comes
on after approximately 10 seconds.
(bn) At the same time:
− Hold the control wheel in
position
− Turn the L /C0065 /C0034 R knob to
the left until the FD V-bar on
the PFD shows a left
command.
On the PFDs the yellow R legend comes
on after approximately 5 seconds (this
shows an aileron mistrim condition). On
the Primary EICAS Display (PED), the
amber ROLL MISTRIM legend comes on
after approximately 10 seconds.
(bo) At the same time:
− Hold the control wheel in
position
− Turn the L /C0065 /C0034 R knob to
the right until the FD V-bar on
the PFD shows a left
command.
On the PFDs the yellow R legend comes
on after approximately 5 seconds (this
shows an aileron mistrim condition. On the
Primary EICAS Display (PED), the amber
ROLL MISTRIM legend comes on after
approximately 10 seconds.
(bp) On the control wheel, push the
AP DISCONNECT pushbutton.
The autopilot disengages and the cavalry
charge audio warning is heard.
You can move the control wheel freely.
(bq) On the APP, lift the AP lever. The autopilot engages.

### Page 11

Service Bulletin
15 June 2018
 
2000−22−008
Page 11 of 42
ACTION RESULT
(br) Turn the /C0089 DN /C0066 UP wheel
until the FD V-bar on the PFDs
shows a pitch up command.
The control column moves rearward.
On the Primary EICAS Display (PED), on
the TRIM/ PITCH/UP/DN display, the
pointers show a pitch up indication.
(bs) Turn the  DN  UP wheel until
the FD V-bar on the PFDs show
a pitch down command.
The control column moves forward.
On the Primary EICAS Display (PED), on
the TRIM/ PITCH/UP/DN display, the
pointers show a pitch down indication.
(bt) On the control wheel, push the
AP DISCONNECT pushbutton.
The autopilot disengages and the cavalry
charge audio warning is heard.
(bu) On the control wheel, push the
AP DISCONNECT pushbutton a
second time.
The cavalry charge audio warning goes
off.
(bv) On the left main landing-gear,
set the weight-on-wheels switch
5GA/S3 to the flight position.
(bw) On the APP, lift the YD lever.
(bx) On the overhead panel TEST 2,
set the EFIS R switch to the top
position.
(by) On the RH DCP, momentarily
turn the FORMAT knob past the
SEL position.
On the RH Multi-Function Display (MFD)
the MAINTENANCE menu is shown.
(bz) On the RH DCP:
1 Use the VOR 2 or the ADF
2 pushbutton to move the
cursor to the FCC
DIAGNOSTIC line.
2 Push the RDR pushbutton
to set the FCC
DIAGNOSTIC page.
3 Rotate the format knob to
the right until STOP while
you push the RDR key in
the DCP.
On the RH MFD the FCC DIAGNOSTIC
PAGE is shown.
(ca) On the FCP:
− Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0065 (FD 1)
position
− Push and hold three
mode-select pushbuttons at
the same time for a minimum
of three seconds.
On the LH PFD the TEST legend is
shown.

### Page 12

Service Bulletin
15 June 2018
 
2000−22−008
Page 12 of 42
ACTION RESULT
(cb) Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0034 (FD 2)
position, and at the same time
push and hold three mode-select
pushbuttons for a minimum of
three seconds.
On the RH PFD the TEST legend is
shown.
(cc) Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0065 (FD 1)
position.
On the RH MFD the REPORT MODE
diagnostic page is shown.
(cd) Push two mode-select
pushbuttons at the same time
and continue until the OUTPUT
MODE diagnostic page is shown
on the RH MFD.
The OUTPUT MODE diagnostic page is
shown on the RH MFD.
(ce) Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0034 (FD 2)
position.
On the RH MFD the REPORT MODE
diagnostic page is shown.
(cf) Push two mode-select
pushbuttons at the same time
and continue until the OUTPUT
MODE diagnostic page is shown
on the RH MFD.
The OUTPUT MODE diagnostic page is
shown on the RH MFD.
(cg) Push one of the mode-select
pushbuttons on the FCP to move
the cursor below the first line of
the output mode data.
The > symbol is on the top line.
(ch) On the APP, move the pitch
knob to set RUDCMD on the top
line of the MFD displays.
The RUDCMD text is shown on the top
line and the RUDCMD value is 0.0.
The text below the MODIFY legend is
BOTH
(ci) On the EICAS Control Panel
(ECP), push the FCS
pushbutton.
On the Secondary EICAS Display (SED),
the FCS page is shown.
(cj) On the APP, use the L /C0065 /C0034 R
knob to change the RUDCMD
value to + 5.0.
On the SED, on the FCS page, the rudder
position is shown as - 5.0/C0095 plus or minus
1.0 /C0095.
(ck) Use the L /C0065 /C0034 R knob to
increase the RUDCMD value to
+10.0  /C0095.
The rudder position shown on the SED
does not increase to more than - 5.0 /C0095.
(cl) Use the L /C0065 /C0034 R knob to
change the RUDCMD to - 5.0 /C0095.
The rudder position moves to + 5.0 /C0095 plus
or minus 1.0 /C0095.
(cm) Use the L /C0065 /C0034 R knob to
change the RUDCMD value to
-10 /C0095.
The rudder position shown on the SED
does not increase to more than + 5.0 /C0095.
(cn) Use the L /C0065 /C0034 R knob to set
the RUDCMD value to 0.0

### Page 13

Service Bulletin
15 June 2018
 
2000−22−008
Page 13 of 42
ACTION RESULT
(co) Use the /C0089 DN /C0066 UP wheel to
set the RUDTRM parameter on
the first line of the OUTPUT
MODE display.
The RUDTRM text is shown on the top
line and the RUDTRM value is 0.0.
The text below the MODIFY legend is
BOTH.
(cp) Use the L /C0065 /C0034 R knob to
change the RUDTRM value to +
50.0.
The rudder trim and the rudder position
move in a positive direction.
(cq) Use the L /C0065 /C0034 R knob to
change the RUDTRM value to -
50.0 /C0095.
The rudder trim and the rudder position
move in a negative direction.
(cr) Use the L /C0065 /C0034 R knob to set
the RUDTRM value to 0.0.
(cs) On the FCP, push and hold three
mode-select pushbuttons at the
same time for a minimum of five
seconds.
The TEST legend on the RH PFD goes
off.
(ct) Use the /C0065 1 2 /C0034 pushbutton
and set it to the /C0065 (FD1)
position.
(cu) Push and hold three mode-select
pushbuttons at the same time for
a minimum of five seconds.
On the LH PFD, the TEST legend goes
off.
(cv) On the overhead panel TEST 2,
set the EFIS R switch to the
lower position
(cw) On the RH DCP, set the
FORMAT knob to the ROSE
position.
(cx) On the APP, lift the AP lever. The autopilot engages and the green AP
<- legend is shown on the LH and RH
PFD.
(cy) Open the circuit breaker:
− L AP (9VU: G-14).
On the Autopilot Panel (APP),
− The autopilot and the yawdamper
disengages and the cavalry charge
audio warning is heard
− On the LH and RH PFD, the red AP <-
legend is shown.
(cz) On the control wheel, push the
AP DISCONNECT pushbutton.
The AP <- legend changes from red to
white and the cavalry charge audio
warning goes off.
(da) Close the circuit breaker:
− L AP (9VU: G-14).
(db) On the APP, lift the AP lever. The autopilot engages and the green AP
<- legend is shown on the LH and RH
PFD.

### Page 14

Service Bulletin
15 June 2018
 
2000−22−008
Page 14 of 42
ACTION RESULT
(dc) Open the circuit breaker:
− R AP (10VU: N-14).
On the Autopilot Panel (APP),
− The autopilot and the yawdamper
disengages and the cavalry charge
audio warning is heard
− On the LH and RH PFD, the red AP <-
legend is shown.
(dd) On the control wheel, push the
AP DISCONNECT pushbutton.
The AP <- legend changes from red to
white and the cavalry charge audio
warning goes off.
(de) Close the circuit breaker:
− R AP (10VU: N-14).
(df) On the APP, lift the AP lever. The autopilot engages and the green AP
<- legend is shown on the LH and RH
PFD.
(dg) On the control wheel, push the
AP DISCONNECT pushbutton.
The autopilot disengages and the cavalry
charge audio warning is heard.
(dh) On the control wheel, push the
AP DISCONNECT pushbutton a
second time.
The cavalry charge audio warning goes
off.
G. OPERATIONAL TEST
(1) Do the operational test of the Individual Main and Standby Pitch Trim-Switches (Ref. AMM
TASK 27−32−00−710−801
H. JOB CLOSE −UP
(1) Remove the External AC Power (Ref. AMM TASK 24−00−00−860−802)
(2) Remove all the tools and the equipment from the work area. Make sure the work area is clean.
(3) Install the following access panels:
− 117AL
− 117AZ
− 118AR
− 220AZ.

### Page 15

Service Bulletin
15 June 2018
 
2000−22−008
Page 15 of 42
3. MATERIAL INFORMATION
FOR A/C 004−019
A. Modification Kit No SAAB 2000 −22−008−01 contains:
Item Part Number Qty Nomenclature Designation Remarks
S2420 D −436−36 1 Splice 306VS −AP
RSD20 M39029/101 −553 9 Contact 34CC
35CC
36CC
37CC
16FD
− RNF−100 3/16 1 Marker sleeve 306VS −AP
− 55T8015−24−9 500mm Wire CC3000 −2401
− 55T8015−24−9 3000mm Wire CC3001 −2401
− 55T8015−24−9 500mm Wire CC3002 −2401
− 55T8015−24−9 3000mm Wire CC3004 −2401
− 55T8015−24−9 1000mm Wire FD3000 −2401
FOR A/C 020−063
B. Modification Kit No SAAB 2000 −22−008−02 contains:
Item Part Number Qty Nomenclature Designation Remarks
S2420 D −436−36 2 Butt splice 305VS −PB
305VS−HW
RSD20 M39029/101 −553 8 Contact 34CC
35CC
36CC
37CC
− RNF−100 3/16 1 Marker sleeve 305VS −PB
− RNF−100 3/16 1 Marker sleeve 305VS −HW
− 55T8015−24−9 500mm Wire CC3000 −2401
− 55T8015−24−9 500mm Wire CC3001 −2401
− 55T8015−24−9 3000mm Wire CC3002 −2401
− 55T8015−24−9 500mm Wire CC3004 −2401
− 55T8015−24−9 3000mm Wire CC3005 −2401
FOR A/C ALL
C. Local supply
Item Part Number Qty Nomenclature Designation Remarks
− Nitto 665 AR Silicone tape −−
−− AR Lacing cord −−
−− AR Cable −ties −−

### Page 16

Service Bulletin
15 June 2018
 
2000−22−008
Page 16 of 42
THIS PAGE INTENTIONALLY LEFT BLANK

### Page 17

Service Bulletin
15 June 2018
 
2000−22−008
Page 17/18 of 42
Wire Routing
FIG. 1
B23726
B23726

### Page 18

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 18

### Page 19

Service Bulletin
15 June 2018
 
2000−22−008
Page 19/20 of 42
Wiring Diagram System CC − Pre Mod A/C 004−019
FIG. 2 (Sheet 1 of 2)
B23710
2
2
2
2
2
CD
CC
922
801
A4 801
924
802
A12
804
924
924
11
801804
801
801
924801
X2
X1
A2
924801
X2
X1
A2
A1
A1
B1
B1
B2
B2
A14
A15
B3
C3
A3
A2
D3
B2
C2
C3
B3
D2
D3
C3
C2
B3
B2
16
X2
X2
X1
X1
A1
A1
A6
A7
S
K
H
C
A12
A13
924 801 801
A2B1
A2
A14
D2
B2
A3
A3
810A11
A9
P
801
802B
J
5
A
R
C2
A3
A2
A1
B10A14
B9A13
A6A12
A5A11
7NC
6C
7C
8C
8NC
6NC
A15 A7
A16 A8
928
801
802
928
928
928
801
802 802
801
928
928
A17
A18
CC157−24
CC324−24
WH
BK
BK
WH
CC236−24
CC236−24
CC231−24
CC231−24
CC453−24
CC453−24
CC452−24
CC451−24
CC451−24
CC243−24
WH
BK
CC238−24 CC238 −24
CC395−24
CC437−24
BK
WH CC416−24
CC436−24
CC417−24
CC417−24
CC418−24
CC418−24
CC419−24
CC419−24
CC392−24 CC392−24
CC410−24
CC410−24
CC415−24
CC415−24
CC407−24
CC407−24
CC408−24
CC408−24
CC409−24
CC409−24
CC414−24
CC413−24
CC412−24
CC411−24
CC406−24
CC405−24
CC404−24
CC403−24
CC402−24
CC401−24
CC400−24
CC399−24
CC398−24
CC396−24
CC393−24
WH
BK
BK
WH
BK
WH
BK
WH
CC235−24
CC313−24
CC237−24
CC230−24
CC312−24
BK
WH
CC232−24
BK
WH CC146−24CC146−24
BK
WH
CC151−24
CC151−24
CC352−24
CC233−24
CC233−24
CC239−24
CC239−24
CC315−24
WH
BK
CC354−24
CC355−24
CC355−24
CC353−24
CC137−24
CC137−24
CC121−24
CC156−24 CC301−24
CC477−24
CC480−24
BK
WH
CC478−24
CC479−24
CC472−24
CC471−24
CC473−24
CC474−24
BK
WH
CC481−24
CC481−24
WH
BK
BK
WH
CC485−24
CC482−24
CC476−24
CC476−24
CC486−24
CC483−24
CC470−24
CC475−24
WH
BK
BK
WH
CC487−24
CC484−24
CC488−24
CC490−24 CC491−24
CC489−24
SHT 5
CB
CA
SHT 1
306VSGL
SHT 5
SHT 2
306VSEA
306VSEB
306VSEC
306VSDC
306VSDG
306VSDF
306VSDY
X1
X2
A1
B1
C1
D3
D1 WH
306VSCU
D2
FD
306VSGH
306VSGJ
306VSGK
SHT 4
3
DWG REF .  7327090−505    SHEET 3 OF 6    REV. C
306VT
M
P4J4
J1
J1
J1J1
J1J1
J1 J1
P6J6
94VP
C
306VNP
C
306VNP
RELAY
RELAY
36CC
34CC
16FD
RELAY
RELAY
RELAY
P2J2
35VU
54CC
52CC
J5 P5
95VP
J1P1
90VP
306VU  ELECTRICAL CENTER
306VNP
B
95VP
11CS
SWITCH
54VU
J2P2
92VP
J2 P2
B23710

### Page 20

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 20

### Page 21

Service Bulletin
15 June 2018
 
2000−22−008
Page 21/22 of 42
Wiring Diagram System CC − Pre Mod A/C 004−019
FIG. 2 (Sheet 2 of 2)
B23711
D3
A
R
P 9
J
B
802
801
D3
810
S
K
H
C
C1
D2
D2
B1
C2
C2
801 924
B2
X1
X2
C3
A3
C3
B3
C1
924
801
A1
A2
X1
X2
2
2
A9
A11
A13
A12
A15
A14
2C
2NO B3 A7
B4 A9
10
CC161−24CC161−24
CC191−24CC191−24
CC183−24CC183−24 CC302−24
CC173−24
CC162−24
CC278−24
CC278−24
CC351−24
CC277−24
CC277−24
CC242−24
CC242−24
WH
BK CC306−24CC306−24
CC334−24
CC300−24
CC279−24BK
WH
CC350−24
CC240−24
WH
BK
WH
BK
CC274−24
CC31 1−24
CC325−24
CC325−24 BK
WH
CC275−24
CC276−24
WH
BK
CC272−24
CC273−24
CC273−24
CC241−24
CC241−24
CC307−24
CC307−24
CC195−24
CC195−24
CC303−24
CC303−24CC460−24
CC464−24
CC461−24
CC465−24 CC466−24
CC466−24
CC339−24
SHT 2
305VSDV
305VSDU
305VSDB
305VSDC
305VSDX
305VS A
SHT 2
305VSCS
SHT 3
3
SHT 1 CS
SHT 1
DWG REF.  7327090−505    SHEET 4 OF 6    REV. C
J1
J1
37CC
RELAY
35CC
RELAY
305VU  ELECTRICAL CENTER
J5 P5
95VP
305VNP
B
J1P1
89VP
11CS
SWITCH
54VU
J1 P1
91VP
P3 J3
B
305VNP
B23711

### Page 22

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 22

### Page 23

Service Bulletin
15 June 2018
 
2000−22−008
Page 23/24 of 42
Wiring Diagram System FD − Pre Mod A/C 004−019
FIG. 3
B23715
B18
B15
C2
C2
C1
C1
DB
DA
DC
BC
BB
BA
A9
A8
A7
15
AC
AB
AA
8
15
B3
B4
B3
B4
CA
47
48
66
B16
62
63
65
B20
B19
A2
A1
A4
B14
B13
B19
B20
A1
A1 X2
A2
X1
B1
A1
X2
X1
A2
C1
D3
X1
D2
A8
B8
63
62
65
66
47
48
BA
BB
BC
802
809
801
802
924
802
922
BA
BB
BC
808
807
806
AC
AB
AA
924
CD
B7
B15 B15 32
X1
X2
CB
924
924
A7
BA
BC
BB
A5 A20 32
15
801
801
802
803
A15
B3
A19
B3
922
929
929
802
803
42A18
42A20
B9
B10
B9
B9
A10
A10
B10
B9
D3
D2
13X2
802
BA
BB
3
1
7
2
BA
BB
B8
B7
929929
929
929
929
929
929
929
929
929
929
929
929
929
929
929
2
3
805
FD417−24
FD417−24
FD304−24FD304−24
FD338−24
FD260−24
FD260−24
FD260−24
FD322−24
FD322−24
FD252−24
FD252−24
FD252−24
FD274−24
FD274−24
FD389−24I
FD388−24I
FD352−24I
FD412−24I FD412 −24I
OR
BL
VT
OR
BL
VT
FD413−24I
FD420−24
FD420−24
FD416−24
FD416−24
FD415−24
FD415−24
FD419−24
FD419−24
OR
BL
VT
OR
BL
VT
FD259−24
FD259−24
FD314−24FD314−24
FD253−24FD253−24
FD38−24
FD38−24
FD131−24
FD131−24
FD292−24
FD394−24
FD394−24
FD393−24
FD393−24
BL
VT
BL
FD295−24
FD295−24
FD278−24
FD278−24
FD318−24FD318−24
FD286−24FD286−24
FD288−24
FD288−24
FD291−24I
FD291−24I
FD294−24I
FD294−24I
FD303−24
FD319−24
FD280−24
FD279−24
FD344−24
FD296−24
FD287−24
FD290−24
FD317−24
FD264−24I FD264−24I
FD267−24
FD267−24
FD273−24FD273−24
FD265−24
FD265−24
FD289−24
FD284−24
FD271−24I
FD271−24I
FD272−24
FD272−24
VT VT
FD390−24
BL
FD395−24
FD396−24I
FD392−24
FD392−24
FD391−24
FD391−24
FD385−24
FD384−24
FD293−24
FD64−24FD64−24
VT
BL
VT
BL
VT
BL
VT
BL
FD397−24I
FD398−24I VTBL
FD37−24
FD269−24
FD430−24
TRIM PWR IN A
TRIM DN ARM B
TRIM UP CMD(+) B
TRIM PWR IN B
SHT 1203VS X
AP ENGAGE A
AP ENGAGE B
TRIM UP ARM A
TRIM DN CMD(+) A
TRIM RATE A UP (H)
TRIM RATE A DN (L)
TRIM RATE B UP (H)
TRIM RATE B DN (L)
TRIM PWR OUT B
D1
C2
B2
A2
CC
FC
FF
A3
A2
B3
B2
TRIM FAIL ANN A
TRIM FAIL ANN B
TL
TL
MAN TRIM DISENGAGE A
MAN TRIM DISENGAGE B
D1 WH
WH
305VSCP
AP ENGAGED B
A3
B3
C3
CC
TRIM PWR OUT A
AP ENGAGED A
S4
S1
DWG REF.  7334291−505    SHEET 4 OF 4    REV. A
206VU
J1J1
9FD
J1
A
305VNP
203VU AVIONICS RACK
M
306VT
RH ELECTRICAL CENTRE
1FS PROCESSING UNIT
INTEGRATED AVIONICS
306VNP
C
C
306VNP
16FD
PEDESTAL
J1
J1
203VNP
306VT
F
A
306VU
SIG INTEGRATING PANEL 2
SIG INTEGRATING PANEL 1
205VU
J1
P1
J1
203VNP
J10
J10 P10
10FD
AUTOPILOT PNL
8FD
3VT
RP2
LP2
P2 J2 P10
P16J16
P1 J1
P16J16
P3J3
LH ELECTRICAL CENTRE
15FD
305VU
DD
DB
D
3VNP
B
C
4VT
B
B
4VNP
ELEV TRIM
ELEV TRIM UP RLY
AP ENGAGED RLY 2
AP ENGAGED RLY 1
306VT
G
TRIM PANEL
35VU
18CC
STANDBY
PITCH CTL P2J2
P17J17
P17J17
DOWN RELAY
B23715

### Page 24

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 24

### Page 25

Service Bulletin
15 June 2018
 
2000−22−008
Page 25/26 of 42
Wiring Diagran System CC − Pre Mod A/C 020−063
FIG. 4 (Sheet 1 of 3)
B23712
C1
A1
B1 X1
X2
924924
922
C2
A2
B2
802 801
B3
A3
C3
2
A12
11
701 702
1
2
B7
C
B
A
R
E
F
J
1001
1001
1001
J
X
E
D
C
B
A
P14
S2
1001
1 −4
2
+41
3
2
−41
1
3
+4
922
922922
A17
A16
A18
A15 801801
B11
922
801801
B9
B6
B1
804
A6
A8
A7
A10
922
922
922
802
803 803
A2
A5
A1
A3
A4 16
B5
A7
A8
A9
+1 4
4−1
4−1
+1 4
4−1
3
4+1
3
+1 4
2
−14
A10
911
CC32−24
CC32−24
CC41−24
WH
BK
RD
CC37−24
CC38−24
BK
WH
RD
CC44−24
CC30−24
CC30−24
CC10−24
CC701−24
CC390−24
CC101−24
CC438−24
BK
WH
RD
CC601−24
BK
WH
RD
BK
WH
RD
CC501−24
BK
WH
RD
CC149−24
CC159−24
CC48−24
CC48−24
CC23−24 CC23 −24
CC45−24
CC45−24
CC20−24
CC20−24
CC60−24
CC60−24
CC165−24
CC39−24 CC39−24
CC218−24
CC50−24CC52−24
CC49−24CC51−24
RD
WH
BK
RD
WH
BK
CC46−24CC43−24
CC40−24
RD
WH
BK
RD
WH
BK
CC387−24 CC387 −24
CC215−24
CC216−24
CC219−24
CC74−24
RD
BK
WH CC47−24 CC47−24
RD
WH
BK
CC35−24
RD
WH
BK
CC326−24
CC71−24
WH
BK
RD
CC174−24
CC31−24
CC28−24CC28−24
CC33−24 CC33−24
CC170−24
CC36−24
CC176−24
CC27−24
CC27−24
CC9−24
CC189−24
CC189−24
CC25−24
CC186−24
CC190−24
CC188−24
CC188−24
CC24−24CC24−24
CC187−24
CC21−24
CC21−24
CC185−24
CC22−24
CC15−24 CC15−24
CC504−24
CC604−24
CC604−24
CC76−24
CC175−24
CC175−24
CC61−24
CC61−24
CC171−24
CC68−24 CC69−24
CC69−24
CC12−24
CC11−24
CC725−24
CC725−24
CC726−24
CC726−24
35VS U
DE
DE
305VS A
3
23
2
23
32
23
2
3
2
ROUTE ALONG CABIN
ROUTE ALONG CABIN
S1
S2
S3
S4
S1
S2
S3
S4
+
−
+
−
+
−
+
−
35VS F
35VS E
35VS J
35VS D
35VS R
35VS Q
35VS P
3
2
3
2
S4
S3
S2
S1
FD
K
G
F
K
G
F
FLOOR LH SIDE
CEILING RH SIDE
SHT 2
35VS A
SHT 3
SHT 5
SHT 2
SHT 4
X1
X2
A1
A2
A3
B1
B2
B3
B3
B2
B1
A3
A2
A1
X2
X1
C1
D1
C2
C3
D2
D3
3
1C
2C
3C
4C
5C
6C
7C
8C
1NC
1NO
2NO
2NC
3NO
3NC
4NO
4NC
5NC
5NO
6NO
6NC
7NO
7NC
8NO
8NC
SHT 5
FD FD
35VS V
FD
35VS W
305VSHW FD
THE WIRES CC−376 AND CC−377 WITH LENGTH 1400 MM ARE ADDED
WITH 700 MM TO 2100 MM ONLY FOR A/C FLIGHT INSPECTION
4
911
911
911
911
S1 3
S2 2
S3 3
S4 2
DWG REF.  7327090−506    SHEET 1 OF 6    REV. J
J2 P2
R
L
L
R
CENTER PEDESTAL
94VP
TRIM PANEL35VU
P1J1
P1J1
DN
UP
16CC ROLL
5CC
STBY ROLL
STBY PITCH
18CC
136VP
P1J1
P1J1
135VP
P1J1
7CC
7CC
RIGHT WING
P1J1
4CC
4CC
TRIM ACTUATORTRIM ACTUATOR
136VNP
A
135VNP
A
B
36VNP
P5 J5
93VP
P4 J4
LEFT WING
 LH AILERON RH AILERON
94VP
P4 J4
70CC
B
36VNP
93VP
J1P1
25FD
J1
AP ENG RLY
J1
305VU LH ELECTRICAL CENTER
B23712

### Page 26

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 26

### Page 27

Service Bulletin
15 June 2018
 
2000−22−008
Page 27/28 of 42
Wiring Diagram System CC − Pre Mod A/C 020−063
FIG. 4 (Sheet 2 of 3)
B23713
B23713
2
2
2
2
2
CD
CC
922
801
A4 801
924
802
A12
804
924
924
11
801804
801
801
924801
X2
X1
A2
924801
X2
X1
A2
A1
A1
B1
B1
B2
B2
A14
A15
B3
C3
A3
A2
D3
B2
C2
C3
B3
D2
D3
C3
C2
B3
B2
16
X2
X2
X1
X1
A1
A1
A6
A7
S
K
H
C
A12
A13
924 801 801
A2B1
A2
A14
D2
B2
A3
A3
810A11
A9
P
801
802B
J
5
A
R
C2
A3
A2
A1
B10A14
B9A13
A6A12
A5A11
7NC
6C
7C
8C
8NC
6NC
A15 A7
A16 A8
922
801
802
922
922
922
801
802 802
801
922
922
A17
A18
CC157−24
CC324−24
WH
BK
BK
WH
CC236−24
CC236−24
CC231−24
CC231−24
CC453−24
CC453−24
CC452−24
CC451−24
CC451−24
CC243−24
WH
BK
CC238−24 CC238 −24
CC395−24
CC437−24
BK
WH CC416−24
CC436−24
CC417−24
CC417−24
CC418−24
CC418−24
CC419−24
CC419−24
CC392−24 CC392−24
CC410−24
CC410−24
CC415−24
CC415−24
CC407−24
CC407−24
CC408−24
CC408−24
CC409−24
CC409−24
CC414−24
CC413−24
CC412−24
CC411−24
CC406−24
CC405−24
CC404−24
CC403−24
CC402−24
CC401−24
CC400−24
CC399−24
CC398−24
CC396−24
CC393−24
WH
BK
BK
WH
BK
WH
BK
WH
CC235−24
CC313−24
CC237−24
CC230−24
CC312−24
BK
WH
CC232−24
BK
WH CC146−24CC146−24
BK
WH
CC151−24
CC151−24
CC352−24
CC233−24
CC233−24
CC239−24
CC239−24
CC315−24
WH
BK
CC354−24
CC355−24
CC355−24
CC353−24
CC137−24
CC137−24
CC121−24
CC156−24 CC301−24
CC477−24
CC480−24
BK
WH
CC478−24
CC479−24
CC472−24
CC471−24
CC473−24
CC474−24
BK
WH
CC481−24
CC481−24
WH
BK
BK
WH
CC485−24
CC482−24
CC476−24
CC476−24
CC486−24
CC483−24
CC470−24
CC475−24
WH
BK
BK
WH
CC487−24
CC484−24
CC488−24
CC490−24 CC491−24
CC489−24
SHT 5
CB
CA
SHT 1
306VSGL
SHT 5
SHT 2
306VSEA
306VSEB
306VSEC
306VSDC
306VSDG
306VSDF
306VSDY
X1
X2
A1
B1
C1
D3
D1 WH
306VSCU
D2
FD
306VSGH
306VSGJ
306VSGK
SHT 4
3
DWG REF.  7327090−506    SHEET 3 OF 6    REV. J
306VT
M
P4J4
J1
J1
J1J1
J1J1
J1 J1
P6J6
94VP
C
306VNP
C
306VNP
RELAY
RELAY
36CC
34CC
16FD
RELAY
RELAY
RELAY
P2J2
35VU
54CC
52CC
J5 P5
95VP
J1P1
90VP
306VU  ELECTRICAL CENTER
306VNP
B
95VP
11CS
SWITCH
54VU
J2P2
92VP
J2 P2

### Page 28

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 28

### Page 29

Service Bulletin
15 June 2018
 
2000−22−008
Page 29/30 of 42
Wiring Diagram System CC − Pre Mod A/C 020−063
FIG. 4 (Sheet 3 of 3)
B23714
B23714
D3
A
R
P 9
J
B
802
801
D3
810
S
K
H
C
C1
D2
D2
B1
C2
C2
801 924
B2
X1
X2
C3
A3
C3
B3
C1
924
801
A1
A2
X1
X2
2
2
A9
A11
A13
A12
A15
A14
2C
2NO B3 A7
B4 A9
10
CC161−24CC161−24
CC191−24CC191−24
CC183−24CC183−24 CC302−24
CC173−24
CC162−24
CC278−24
CC278−24
CC351−24
CC277−24
CC277−24
CC242−24
CC242−24
WH
BK
CC306−24CC306−24
CC334−24
CC300−24
CC279−24BK
WH
CC350−24
CC240−24
WH
BK
WH
BK
CC274−24
CC311−24
CC325−24
CC325−24
BK
WH
CC275−24
CC276−24
WH
BK
CC272−24
CC273−24
CC273−24
CC241−24
CC241−24
CC307−24
CC307−24
CC195−24
CC195−24
CC303−24
CC303−24CC460−24
CC464−24
CC461−24
CC465−24 CC466−24
CC466−24
CC339−24
SHT 2
305VSDV
305VSDU
305VSDB
305VSDC
305VSDX
305VS A
SHT 2
305VSCS
SHT 3
3
SHT 1 CS
SHT 1
DWG REF.  7327090−506    SHEET 4 OF 6    REV. J
J1
J1
37CC
RELAY
35CC
RELAY
305VU  ELECTRICAL CENTER
J5 P5
95VP
305VNP
B
J1P1
89VP
11CS
SWITCH
54VU
J1 P1
91VP
P3 J3
B
305VNP

### Page 30

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 30

### Page 31

Service Bulletin
15 June 2018
 
2000−22−008
Page 31/32 of 42
Wiring Diagram System CC − Post Mod A/C 004−019
FIG. 5 (Sheet 1 of 2)
B23717
B23717
DWG REF.  7327090−801   SHEET  3 OF 6   REV

### Page 32

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 32

### Page 33

Service Bulletin
15 June 2018
 
2000−22−008
Page 33/34 of 42
Wiring Diagram System CC − Post Mod A/C 004−019
FIG. 5 (Sheet 2 of 2)
B23718
B23718
RH ELECTRICAL CENTER
306VU
306VSAP
36CC
RELAY
J1
FD
305VNP
B
SHT 1
J3P3
CSSHT 1
3
91VP
P1J1
54VU
SWITCH
11CS
SHT 3
305VSCS
SHT 2
305VS A
89VP
P1J1
B
305VNP
305VSDX
95VP
P5J5
305VU  ELECTRICAL CENTER
305VSDC
305VSDB
RELAY
35CC
RELAY
37CC
305VSDU
305VSDV
J1
J1
SHT 2
APPSKD
2
2
C3
A3
B2
10
A9B4
A7B32NO
2C
A14
A15
A12
A13
A11
A9
X2
X1
A2
A1
801
924
C1
B3
C3
A2
C3
X2
X1
B2
924801
C2
C2
B1
D2
D2
C1
C
H
K
S
810
D3
801
802
B
J
9P
R
A
D3
CC3004−24
CC3004−24
CC3001−24
CC3001−24
CC3001−24
CC3000−24
CC3000−24
CC339−24
CC466−24
CC466−24CC465−24
CC461−24
CC464−24
CC460−24 CC303−24
CC303−24
CC195−24
CC195−24
CC307−24
CC307−24
CC241−24
CC241−24
CC306
CC195
CC325
CC273−24
CC273−24
CC272−24
BK
WH
CC276−24
CC275−24
WH
BKCC325−24
CC325−24
CC311−24
CC274−24
BK
WH
BK
WH
CC240−24
CC350−24
WH
CC300−24
CC334−24
CC306−24 CC306−24BKWH
CC242−24
CC242−24
CC277−24
CC277−24
CC351−24
CC278−24
CC278−24
CC162−24
CC173−24
CC302−24CC183−24 CC183−24
CC191−24 CC191−24
CC161−24 CC161 −24
DWG REF.  7327090−801   SHEET 4 OF 6   REV.
CC279−24BK

### Page 34

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 34

### Page 35

Service Bulletin
15 June 2018
 
2000−22−008
Page 35/36 of 42
Wiring Diagram System FD − Post Mod  A/C 004−019
FIG. 6
B23727
B23727
DWG REF.  7334291−804   SHEET 4 OF 4   REV.

### Page 36

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 36

### Page 37

Service Bulletin
15 June 2018
 
2000−22−008
Page 37/38 of 42
Wiring Diagram System CC − Post Mod A/C 020−063
FIG. 7 (Sheet 1 of 3)
B23719 DWG REF.  7327090−802   SHEET 1 OF 6   REV.
B23719

### Page 38

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 38

### Page 39

Service Bulletin
15 June 2018
 
2000−22−008
Page 39/40 of 42
Wiring Diagram System CC − Post Mod A/C 020−063
FIG. 7 (Sheet 2 of 3)
B23720 DWG REF.  7327090−802   SHEET 3 OF 6   REV.
B23720

### Page 40

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 40

### Page 41

Service Bulletin
15 June 2018
 
2000−22−008
Page 41/42 of 42
Wiring Diagram System CC − Post Mod A/C 020−063
FIG. 7 (Sheet 3 of 3)
B23721 DWG REF.  7327090−802   SHEET 4 OF 6   REV.
B23721

### Page 42

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000−XX−XXX
Page 42

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
