# Saab Service Bulletin 2000-32-084: Revision 1

- Rights: © Saab. Filed by the FAA in regulations.gov docket FAA-2023-1896, the docket of AD 2023-25-06. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Saab Service Bulletin 2000-32-084](https://openairdocs.org/service-documents/saab/sb-2000-32-084.md)
- Title as filed: SAAB SB 2000-32-084_Rev 01
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/a1/68/a168cd85004d28ad0bd1803cd6192346f4b7d48bc8b18df5aacbe08898d72e1b
- Page: https://openairdocs.org/service-documents/saab/sb-2000-32-084/file/a168cd85004d

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

SAAB 2000
Service Bulletin
ATA CHAPTER: 32
LANDING GEAR - ANTI-SKID - COLOR MARKING OF THE ANTI-SKID/WHEEL SPEED
TRANSDUCER HARNESSES AND THE WHEEL AXLES
Mod No. 6661
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Aircratt:
Aircraft Mfg. Serial No's SAAB 2000 - 004 thru - 063.
(2) Spares:
MLG Shock Strut Assemblies P/N: AIR83078, AIR83084 and AIR83132.
Anti-Skid Harness Sub-Assemblies P/N: AIR134484 and AIR134485.
NOTE: For modification of spares, refer to Para. 2.D.
B. REASON
It has been found possible to connect inboard anti-skid/wheel speed transducer harness (the
harness) to the outboard anti-skid system channel and vice versa in the wheel axle on the main
landing gear. In case the harnesses are cross-connected, there will be a significant reduction in
braking capabilities if the anti-skid function is activated as the system will receive incorrect inputs.
This Service Bulletin introduces color marking of the harnesses and the wheel axles.
Implementation of this Service Bulletin will reduce the possibility to cross-connect the harnesses
and thus eliminate the risk for reduction in braking capabilities.
For additional information, refer to Safety recommendation A-21-55 in NTSB investigation report
AAR-21-05.
C. DESCRIPTION
This Service Bulletin gives instructions for:
- Removal of the main wheels
- Removal of the wheel speed transducers
- Modification of the LH and RH main landing gear:
- Color marking of the harnesses
- Color marking the wheel axles
- Installation of the wheel speed transducers
- Installation of the main wheels
- Functional test to make sure that the harnesses are correctly installed
- If applicable, modification of spares.
D.  COMPLIANCE
Mandatory.
Saab recommends this Service Bulletin to be performed within 12 months or 1500 flight hours,
whichever comes first, from release of this Service Bulletin.
This Service Bulletin is under EASA consideration for an Airworthiness Directive.
The final compliance terms will be set by the EASA Airworthiness Directive (AD) when issued.
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 1 ot 8

### Page 2 (OCR)

SAAB 2000
Service Bulletin
E. APPROVAL
The technical content of this Service Bulletin is approved under the authority of the DOA ref.
EASA.21J.066.
F. MANPOWER
Estimated time to complete this Service Bulletin is:
2 persons required.
Total manhours: 10
Elapsed time (hours): 5
Labour cost at operators expense.
G. MATERIAL - COST AND AVAILABILITY
Refer to Attachment 1, 2 or 3 (HD SB AIR83078-32-12, AIR83084-32-13 or AIR83132-32-03).
H. TOOLING
Refer to Attachment 1, 2 or 3 (HD SB AIR83078-32-12, AIR83084-32-13 or AIR83132-32-03).
I. WEIGHT AND BALANCE
None.
J. ELECTRICAL LOAD DATA
Not affected.
K. REFERENCES
Aircraft Maintenance Manual (AMM)  07-10-00-582-807
07-10-00-582-808
32-12-00-010-801
32-12-00-410-801
32-41-10-000-801
32-41-10-400-801
32-43-17-400-801
32-43-20-000-801
32-43-20-400-801
32-43-25-000-801
32-43-25-400-801
Wiring Diagram Manual (WDM)  20-20-05
HD Service Bulletin  AIR83078-32-12 (Attachment 1)
AIR83084-32-13 (Attachment 2)
AIR83132-32-03 (Attachment 3).
L.  OTHER PUBLICATIONS AFFECTED
Aircraft Maintenance Manual (AMM)
Illustrated Parts Catalog (IPC)
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 2 of 8

### Page 3 (OCR)

SAAB 2000
Service Bulletin
2. ACCOMPLISHMENT INSTRUCTIONS
A. JOB SET-UP
(1) Before you start the SB, make sure:
- The modification kit contains the parts listed in the Service Bulletin
- The material listed in the HD Service Bulletins (Attachment 1, 2 and 3) are available
- The documentation is available.
(2) Open the forward doors of the main landing gear (Ref. AMM TASK 32-12-00-010-801).
(3) Do a functional test and make sure that the anti-skid harnesses are correctly installed on the
LH and RH landing gear Ref. AMM TASK 32-43-17-400-801, Subtask 32-43-17-720-001.
(4) Open the circuit breakers.
(a) On the LH circuit breaker panel 9VU, open and tag the circuit breakers:
LABEL  POS C/B
HYDRAULIC A-SKID INBD  F-10  1GG
HYDRAULIC L LDG CTL  F-11  13GA
(b) On the RH circuit breaker panel 10VU, open and tag the circuit breaker:
LABEL  POS  C/B
HYDRAULIC A-SKID OUTBD  M-8  2GG
HYDRAULIC R LDG CTL  M-9  16GA
(5) Lift the aircraft on the three main jacks (Ref. AMM TASK 07-10-00-582-807).
(6) Remove the main wheel hubcaps (Ref. AMM TASK 32-43-25-000-801).
(7) Remove the main wheel nuts (Ref. AMM TASK 32-41-10-000-801).
(8) Remove the wheel speed transducers (Ref. AMM TASK 32-43-20-000-801). Ensure to retain
the wheel speed transducer harnesses to stop them from recoiling into the main wheel axles.
(9) Clean the upper part of the anti-skid harnesses and the connectors.
(a) Cover the lower part of the LH and RH MLG with a protective cover.
Use a mild detergent and clean the upper part of the anti-skid harnesses and the
connectors 5GA/6GA-P4/P5.
B. MODIFICATION
(1) Modify the LH landing gear
REF. FIG. 1 and Attachment 1, 2 or 3)
(a) Modify the outboard side of the LH landing gear.
Modify the upper part of the harness.
Disconnect connector 5GA-P5, of LH side harness (AIR134485) from the LH
nacelle.
Do a connection checkout of the LH side harness (upper and lower connector)
(Ref. WDM 20-20-05). This is to make sure that correct harness is modified.
Position heat shrink RN-3000-24/8-4 (YELLOW) to LH harness (AIR134485),
as illustrated in Attachment 1, 2 or 3, Figure 2 (END "B"). Using heat gun apply
heat to the heat shrink to retain in position.
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 3 of 8

### Page 4 (OCR)

SAAB 2000
Service Bulletin
d Connect the connector 5GA-P5, of LH harness (AIR134485) to the LH nacelle.
2  Modify the lower part of the harness and the axle.
a  Position the heat shrink RNF-3000-24/8-4 (YELLOW) to the LH harness
(AIR134485), as illustrated in Attachment 1, 2 or 3, Figure 2 (END "A"). Use a
heat gun and apply the heat to the heat shrink to retain in position.
Use the 400 grade abrasive paper or fine grade Scotch-brite. Lightly abrade the
LH outboard diameter of the axle to smooth any rough edges to a feather finish.
Care must be taken not to damage the corrosion protection layer.
Thoroughly clean the LH outboard diameter of the axle, use a suitable cleaning
solvent with a clean lint free cloth made moist with solvent. Allow area to dry
Paint the LH plain section of the outboard diameter of the axle up to the thread,
where indicated in Attachment 1, 2 or 3, Figure 4, using Humbrol enamel gloss
paint color code No. 69 - Yellow (Alt. Revell enamel gloss color code No. 12 -
Let the paint air-dry for 24 hours.
(b) Modify the inboard side of the LA landing gear.
Modify the upper part of the harness.
Disconnect connector 5GA-P4, of RH side harness (AIR134484) from the LH
nacelle.
Position heat shrink RN-3000-24/8-5 (GREEN) to RH harness (AIR134484), as
illustrated in Attachment 1, 2 or 3, Figure 2 (END "B"). Using heat gun apply
heat to the heat shrink to retain in position.
Connect the connector 5GA-P4, of RH harness (AIR134484) to the LH nacelle.
2  Modity the lower part of the harness and the axle.
Position heat shrink RNF-3000-24/8-5 (GREEN) to RH harness (AIR134484),
as illustrated in Attachment 1, 2 or 3, Figure 2 (END "A"). Using heat gun apply
heat to the heat shrink to retain in position.
Using 400 grade abrasive paper or fine grade Scotch-brite. Lightly abrade the
LH outboard diameter of axle to smooth any rough edges to a feather finish.
Care must be taken not to damage the corrosion protection layer.
Thoroughly clean RH outboard diameter of axle, using a suitable cleaning
solvent with clean lint free cloth made moist with solvent. Allow area to dry fully.
Paint the RH plain section of the outboard diameter of the axle up to the thread,
where indicated in Attachment 1, 2 or 3, Figure 4, using Humbrol enamel gloss
paint color code No. 38 - Lime Green (Alt. Revell enamel gloss color code No.
61 - emerald Green).
e  Let the paint air-dry for 24 hours.
(2) Modify the RH landing gear.
REF. FIG. 1 and Attachment 1, 2 or 3)
(a) Modify the inboard side of the RH landing gear.
Modify the upper part of the harness.
Disconnect the connector 6GA-P5, of LH side harness (AIR134485) from the
RH nacelle.
Do a connection checkout of the LH side harness (upper and lower connector)
(Ref. WDM 20-20-05). This is to make sure that correct harness is modified
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 4 of 8

### Page 5 (OCR)

SAAB 2000
Service Bulletin
Position heat shrink RN-3000-24/8-4 (YELLOW) to LH harness (AIR134485),
as illustrated in Attachment 1, 2 or 3, Figure 2 (END "B"). Using heat gun apply
heat to the heat shrink to retain in position.
d  Connect the connector 6GA-P5, of LH harness (AIR134485) to the RH nacelle.
2  Modify the lower part of the harness and the axle.
Position heat shrink RNF-3000-24/8-4 (YELLOW) to LH harness (AIR134485),
as illustrated in Attachment 1, 2 or 3, Figure 2 (END "A"). Using heat gun apply
heat to the heat shrink to retain in position.
Using 400 grade abrasive paper or fine grade Scotch-brite. Lightly abrade the
LH outboard diameter of axle to smooth any rough edges to a feather finish.
Care must be taken not to damage the corrosion protection layer.
Thoroughly clean LH outboard diameter of axle, using a suitable cleaning
solvent with clean lint free cloth made moist with solvent. Allow area to dry fully.
Paint the LH plain section of the outboard diameter of the axle up to the thread,
where indicated in Attachment 1, 2 or 3, Figure 4, using Humbrol enamel gloss
paint color code No. 69 - Yellow (Alt. Revell enamel gloss color code No. 12 -
Let the paint air-dry for 24 hours.
(b) Modify the outboard side of the RH landing gear.
1  Modity the upper part of the harness.
Disconnect the connector 6GA-P4, of RH side harness (AIR134484) from the
RH nacelle.
Position heat shrink RN-3000-24/8-5 (GREEN) to RH harness (AIR134484), as
illustrated in Attachment 1, 2 or 3, Figure 2 (END "B"). Using heat gun apply
heat to the heat shrink to retain in position.
Connect the connector 6GA-P4, of RH harness (AIR134484) to the RH nacelle.
Modify the lower part of the harness and the axle.
Position heat shrink RNF-3000-24/8-5 (GREEN) to RH harness (AIR134484),
as illustrated in Attachment 1, 2 or 3, Figure 2 (END "A"). Using heat gun apply
heat to the heat shrink to retain in position.
Using 400 grade abrasive paper or fine grade Scotch-brite. Lightly abrade the
LH outboard diameter of axle to smooth any rough edges to a feather finish.
Care must be taken not to damage the corrosion protection layer.
Thoroughly clean RH outboard diameter of axle, using a suitable cleaning
solvent with clean lint free cloth made moist with solvent. Allow area to dry fully.
Paint the RH plain section of the outboard diameter of the axle up to the thread,
where indicated in Attachment 1, 2 or 3, Figure 4, using Humbrol enamel gloss
paint color code No. 38 - Lime Green (Alt. Revell enamel gloss color code No.
61 - emerald Green).
e  Let the paint air-dry for 24 hours.
C. JOB CLOSE-UP
(1) Install the LH and RH side wheel speed transducers (Ref. AMM TASK 32-43-20-400-801).
(2) Install the LH and RH side main wheel nuts (Ref. AMM TASK 32-41-10-400-801).
(3) Install the main wheel hubcaps (Ref. AMM TASK 32-43-25-400-801).
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 5 of 8

### Page 6 (OCR)

SAAB 2000
Service Bulletin
(4) Lower the aircraft and remove the three main jacks (Ref. AMM TASK 07-10-00-582-808).
(5) Close the circuit breakers.
(a) On the LH circuit breaker panel 9VU, remove the tag and close the circuit breakers:
LABEL  POS  C/B
HYDRAULIC A-SKID INBD  F-10  1GG
HYDRAULIC L LDG CTL  F-11  13GA
(b) On the RH circuit breaker panel 10VU, remove the tag and close the circuit breaker:
LABEL  POS  C/B
HYDRAULIC A-SKID OUTBD  M-8  2GG
HYDRAULIC R LDG CTL  M-9  16GA
(6) Do a functional test and make sure that the anti-skid harnesses are correctly installed on the
LH and RH landing gear Ref. AMM TASK 32-43-17-400-801, Subtask 32-43-17-720-001.
(7) Close the forward doors of the main landing gear (Ref. AMM TASK 32-12-00-410-801).
(8) Remove all the tools and the equipment from the work area. Make sure the work area is clean.
D. MODIFICATION - SPARES
(1) For MLG shock strut assemblies and anti-skid harnesses held as spares, do the color coding
modification (Ref. Attachment 1, 2 or 3 (HD SB AIR83078-32-12, AIR83084-32-13 or
AIR83132-32-03).
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 6 of 8

### Page 7 (OCR)

SAAB 2000
Service Bulletin
3. MATERIAL INFORMATION
A. Material
Refer to Attachment 1, 2 or 3 (HD SB AIR83078-32-12, AIR83084-32-13 or AIR83132-32-03).
B. Local Supply:
Item  Part Number  Qty  Nomenclature  Designation  Remarks
A/R  Protective Cover  LH/RH MLG  Polyethylene film
or equivalent.
A/R  Mild detergent
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 7 of 8

### Page 8 (OCR)

SAAB 2000
Service Bulletin
(REF GA-P5)
YELLOW
AIR134485  (REF GA-P4)
GREEN
AIR134484
6GA-P4
GREEN
6GA-P5
YELLOW
5GA-P4
GREEN
5GA-P5
YELLOW
RH NACELLE
LH NACELLE
(REF GA-P5)
YELLOW
AIR134485
AIR134484-
(REF GA-P4)
GREEN
B-00574
Color Marking of the Anti-Skid Harnesses and the Wheel Axles
FIG. 1
04 May 2023  2000-32-084
Revision 01, 15 May 2023  Page 8 of 8

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
