# Saab Service Bulletin 33-058: Revision 1

- Rights: © Saab. Filed by the FAA in regulations.gov docket FAA-2017-0479, the docket of AD 2017-17-14. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Saab Service Bulletin 33-058](https://openairdocs.org/service-documents/saab/sb-33-058.md)
- Title as filed: SB-33-058 R01
- Pages: 5
- PDF: https://openairdocs.org/files/sha256/6f/b0/6fb052e88da172603c63669f2b39870e6c5c5c6debf61317a01c77948ffc96b3
- Page: https://openairdocs.org/service-documents/saab/sb-33-058/file/6fb052e88da1

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin
30 May 2016
Revision 01, 21 October 2016
340−33−058
Page 1 of 5
ATA CHAPTER: 33
LIGHTS − PASSENGER READING LIGHT − CHANGE OF CIRCUIT BREAKER FOR
PASSENGER READING LIGHT.
Mod No. 3501
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Aircraft:
Aircraft Mfg. Serial No’s SAAB SF340A − 004 thru − 138.
NOTE: This Service bulletin is not applicable for aircraft with Service Bulletin SAAB 340−33−053
(Modification/Removal for Cargo/Freighter Configuration) implemented.
B. REASON
Circuit breakers of an unsuitable strength, 10A instead of 7.5A, have been found installed for 2LJ and
4LJ.
In case of a small overcurrent in the system, the circuit breakers will not open.
10A is above the safe continuous current for the installed wire dimension. If overcurrent in the system
occur, there is a risk for overheated wires, smell and possibly, smoke or fire.
Implementation of this Service Bulletin will make sure that correct circuit breakers are installed and thus
remove the possibility for overcurrent in the wires.
C. DESCRIPTION
Replacement of oversized circuit breakers 2LJ and 4LJ in the reading system.
D. COMPLIANCE
Mandatory
Saab recommends this Service Bulletin to be performed within 6 months from release of this Service
Bulletin.
This Service Bulletin is under EASA consideration for an Airworthiness Directive.
The final compliance terms will be set by the EASA Airworthiness Directive (AD) when issued.
E. APPROVAL
The technical content of this Service Bulletin is approved under the authority of DOA nr. EASA.21J.066.
F. MANPOWER
Estimated time to complete this Service Bulletin is:
1 persons required.
Total manhours: 2
Elapsed time (hours):
Labour cost at operators expense.

### Page 2

Service Bulletin
30 May 2016
Revision 01, 21 October 2016
340−33−058
Page 2 of 5
G. MATERIAL − COST AND AVAILABILITY
Price and availability for parts required to do this service bulletin will be furnished on request.
H. WEIGHT AND BALANCE
Not affected.
I. ELECTRICAL LOAD DATA
Not affected.
J. REFERENCES
Aircraft Maintenance Manual (AMM) 24 −00−00 Maintenance practices
33−23−05−05  Adjustment / Test
39−10−42−02 Maintenance Prac-
tices
Wiring Manual (WM) 20 −00−00  Standard practices
K. OTHER PUBLICATIONS AFFECTED
Illustrated Parts Catalog (IPC)
Wiring Manual (WM)
2. ACCOMPLISHMENT INSTRUCTIONS
CAUTION: BE CAREFUL WHEN YOU DO THE MODIFICATION OF THE HARNESS.
MAKE SURE THAT YOU DO NOT DAMAGE THE EXISTING WIRES WHEN
NEW WIRES ARE INSTALLED. CLEAN AND INSPECT THE AFFECTED
HARNESS WHEN THE MODIFICATION IS COMPLETED. DAMAGES TO THE
WIRES CAN CAUSE SYSTEM MALFUNCTION.
NOTE: All wiring changes are to be performed in accordance with the procedures in the
WM 20−00−00.
A. JOB SET −UP
(1) Before you start the SB, make sure:
− The modification kit contains the parts listed in the Service Bulletin
− The documentation is available
(2) Make sure the aircraft is safe for maintenance before you start the modification.
(a) Isolate the electrical power (Ref. AMM 24 −00−00, maintenance practices).
(3) Open for access.
REF. FIG 1
CAUTION: BEFORE YOU LOOSEN THE CIRCUIT BREAKER PANEL, MAKE SURE
THAT THE LEFT AND RIGHT BATTERY ARE REMOVED. THAT WILL HELP
TO PREVENT DAMAGE TO THE EQUIPMENT AND STRUCTURE.
(a) Release the fasteners that attach the circuit breaker panel 10VU to the structure and lower
the panel.
B. MODIFICATION
REF. FIG. 1, 2

### Page 3

Service Bulletin
30 May 2016
Revision 01, 21 October 2016
340−33−058
Page 3 of 5
(1) Remove these circuit breakers (101) (Ref. AMM 39 −10−42−02, Maintenance Practices).
− 2 LJ INTERNAL LIGHTS CABIN READ L (L25)
− 4 LJ INTERNAL LIGHTS CABIN READ R (L26).
(2) Install these circuit breakers (1) (Ref. AMM 39 −10−42−02, Maintenance Practices).
− 2 LJ INTERNAL LIGHTS CABIN READ L (L25)
− 4 LJ INTERNAL LIGHTS CABIN READ R (L26).
(3) Install the circuit breaker panel 10VU.
C. JOB CLOSE −UP
(1) Restore the electrical power (Ref. AMM 24 −00−00, maintenance practices).
(2) Do the operational test of the reading lights in the passenger compartment (Ref. AMM
33−23−05−05).
(3) Remove all the tools and the equipment from the work area. Make sure the work area is clean.
3. MATERIAL INFORMATION
A. Parts required for modification:
Item Part Number Qty Nomenclature Designation Remarks
1 MS3320 −7−5 2 Circuit Breaker 7.5A
B. Removal
Item Part Number Qty Nomenclature Designation Remarks
101 MS3320 −10 2 Circuit Breaker 10A Discard

### Page 4

Service Bulletin
30 May 2016
Revision 01, 21 October 2016
340−33−058
Page 4 of 5
A31420
CIRCUIT BREAKER PANEL 10VU
(RH SIDE)
Circuit Breaker − Component Location
FIG. 1

### Page 5

Service Bulletin
30 May 2016
Revision 01, 21 October 2016
340−33−058
Page 5 of 5
Wire Diagram − LJ System A/C 004−138
FIG. 2
A34379
A34379
L/1
L/1
L/1
LJ6-22
LJ4-22
LJ8-20
LJ16-20
INTERNAL LIGHTS
CABIN READ R
INTERNAL LIGHTS
CABIN READ L
7.5A
7.5A
10A
INTERNAL LIGHTS
CABIN READ C
2LJ
4LJ
6LJ
RH CB PNL
10VU 
POST MOD
PART OF DWG 7233292-805    SHEET 1 OF 4   REV.
PART OF DWG 7233292-603    SHEET 1 OF 4   REV.
PART OF DWG 7233292-601    SHEET 1 OF 4   REV.
PART OF DWG 7233292-502    SHEET 1 OF 4   REV.
L/1
L/1
L/1
LJ6-22
LJ4-22
LJ8-20
LJ16-20
INTERNAL LIGHTS
CABIN READ R
INTERNAL LIGHTS
CABIN READ L
10A
10A
10A
INTERNAL LIGHTS
CABIN READ C
2LJ
4LJ
6LJ
RH CB PNL
10VU 
PRE MOD
PART OF DWG 7233292-815    SHEET 1 OF 4   REV.
PART OF DWG 7233292-813    SHEET 1 OF 4   REV.
PART OF DWG 7233292-812    SHEET 1 OF 4   REV.
PART OF DWG 7233292-811    SHEET 1 OF 4   REV.
PART OF DWG 7233292-814    SHEET 1 OF 4   REV. PART OF DWG 7233292-404    SHEET 1 OF 4   REV.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
