# Saab Service Bulletin sb2-32-081-00: No revision named

- Rights: © Saab. Filed by the FAA in regulations.gov docket FAA-2021-0023, the docket of AD 2021-09-11. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Saab Service Bulletin sb2-32-081-00](https://openairdocs.org/service-documents/saab/sb2-32-081-00.md)
- Title as filed: sb2_32_081_00
- Pages: 20
- PDF: https://openairdocs.org/files/sha256/de/86/de86ffd0839872557d85d0ee9e3f5de8b2d0c240e7238b739fbfde4c0249976c
- Page: https://openairdocs.org/service-documents/saab/sb2-32-081-00/file/de86ffd08398

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 1 of 20
ATA CHAPTER: 32
LANDING GEAR ï EMERGENCY EXTENSION ï ENERGIZE LANDING GEAR
TRANSFER VALVE AT LANDING GEAR EMERGENCY RELEASE
Mod No. 6585, 6599
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Aircraft:
Aircraft Mfg. Serial No’s SAAB 2000 ï 004ï063.
(2) Spares: Not affected.
NOTE: This Service Bulletin supersedes and cancels Service Bulletin No. SAAB
2000ï32ï080.
B. REASON
Due to an event where it was not possible to fully retract or extend/locked down Main Landing
Gears, using normal or emergency procedures, causing left Main Landing Gear collapsed after
touchdown, the landing gear system is modified so that the transfer valve is energized to its down
position when emergency handle is used.
C. DESCRIPTION
This Service Bulletin gives instructions for:
ï installation of new relay
ï relocation of wires
ï installation of new wires.
ï functional test.
D. COMPLIANCE
Mandatory.
Saab recommends this Service Bulletin to be performed within 24 months or 3000 flight hours,
whichever comes first, from release of this Service Bulletin.
This Service Bulletin is under EASA consideration for an Airworthiness Directive.
The final compliance terms will be set by the EASA Airworthiness Directive (AD) when issued.
E. APPROVAL
The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21J.066.
F. MANPOWER
Estimated time to complete this Service Bulletin is:
1 person required.
Total manhours: 20
Elapsed time (hours): 20

### Page 2

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 2 of 20
G. MATERIAL ï COST AND AVAILABILITY
Price and availability for Mod Kit. No. SAAB 2000ï32ï081ï01 will be furnished on request.
H. TOOLING
Heat gun.
Crimp tool Positioner Insert tool Removal tool Used for
GMT232 ï ï ï S2016, S2420
M22520/1ï01 TH343 M81969/14ï02 M81969/14ï02 RSD20
M22520/2ï01 K818ï2 CTA 1160 CTA 1160 MS20S
M22520/1ï01 TH441ï1 BL J1276ï1 J1276ï1 TJB16
47386 ï ï ï T1831
(1) Faraday cage (For separation bolts).
(2) Multimeter, FLUKE 177, or equivalent.
I. WEIGHT AND BALANCE
Weight change + 0.19 kg / 0.41 lb
Center of gravity STA 186.9
Change moment 0.35 kgin / 0.76 lbin
100
J. ELECTRICAL LOAD DATA
RH BAT BUS + 0.8A (only when landing gear emergency release is used).
K. REFERENCES
Aircraft Maintenance Manual (AMM) TASK 07 ï10ï00ï582ï807
TASK 07ï10ï00ï582ï808
TASK 24ï00ï00ï860ï801
TASK 24ï00ï00ï860ï802
TASK 24ï00ï00ï860ï805
TASK 24ï00ï00ï860ï806
TASK 24ï31ï10ï710ï801
TASK 29ï10ï00ï860ï801
TASK 29ï10ï00ï860ï803
TASK 29ï20ï29ï200ï801
TASK 31ï15ï10ï400ï801
TASK 32ï00ï00ï000ï801
TASK 32ï00ï00ï400ï801
TASK 32ï30ï00ï720ï801
TASK 32ï32ï20ï760ï801
Wiring Manual 20 ï20ï00
20ï30ï15
20ï20ï30
L. OTHER PUBLICATIONS AFFECTED
Aircraft Maintenance Manual (AMM)
Illustrated Parts Catalog (IPC)

### Page 3

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 3 of 20
Wiring Diagram Manual (WDM)
Aircraft Operations Manual (AOM)
Maintenance Review Board Report (MRB)
2. ACCOMPLISHMENT INSTRUCTIONS
CAUTION: BE CAREFUL WHEN YOU DO THE MODIFICATION OF THE HARNESS.
MAKE SURE THAT YOU DO NOT DAMAGE THE EXISTING WIRES WHEN
NEW WIRES ARE INSTALLED. CLEAN AND INSPECT THE AFFECTED
HARNESS WHEN THE MODIFICATION IS COMPLETED. DAMAGES TO THE
WIRES CAN CAUSE SYSTEM MALFUNCTION.
NOTE: All wiring changes are to be performed in accordance with the procedures in the
WM 20ï00ï00.
NOTE: The color of the lacing cord on the A and the B wire bundles gives the harness class
and identification. The A harness is identified with white lacing cord and the B
harness is identified with red/black lacing cord.
A. JOB SET ïUP
(1) Before you start the SB, make sure:
ï The modification kit contains the parts listed in the Service Bulletin
ï The local supply items listed in the Service Bulletin are available
ï The documentation is available
ï The special tools are available.
(2) Remove the external AC power (Ref. AMM TASK 24 ï00ï00ï860ï802).
(3) Disconnect the LH, RH and CTR Battery (Ref. AMM TASK 24 ï00ï00ï860ï805).
(4) Remove the access panels.
ï 114AZ
ï 118AR
ï 466AZ
B. INSTALLATION
(1) in the RH electrical center 306VU.
REF. FIG. 5 view CïC, DïD and E.
(a) Install the relay socket (602).
(b) Install the marker decal 11GB ïJ1 adjacent to the relay socket (602).
C. MODIFICATION
(1) Loosen and disconnect the connector 94VP ïP4.
(2) Disassemble the connector 94VP ïP4 (Ref. WDM 20ï30ï15).
(3) Relocate the following wires in the RH electrical center 306VU.
REF. FIG. 1, 2, 3, 4 and 5
Wire No Class From Contact To Contact Remarks
GA247ï24 A 94VPïP4:B19 ï 2VSïBY S2420 Connect to-
gether with
GB3007ï20
and
GA3001ï24
GA260ï24 A 94VPïP4:B20 ï 2VSïBX S2420 Connect to-
gether with
GB3005ï20
and
GA3000ï24

### Page 4

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 4 of 20
Wire No RemarksContactToContactFromClass
GB14ï20BK A 94VPïP4:B16 ï 306VSïRG S2016 If necessary,
replace the
wire
GB70ï20
GB62ï20 A 10GBïJ1:B3 ï 306VSïRF S2016
(4) Install the following new wires in the RH electrical center 306VU. Route along the existing
class A harness routing.
REF. FIG. 1, 2, 3, 4 and 5
Wire No Class From Contact To Contact Remarks
GA3000ï24 A 94VPïP4:B20 MS20S 2VSïBX S2420 Connect to-
gether with
GA260ï24
and
GB3005ï20
GA3001ï24 A 94VPïP4:B19 MS20S 2VSïBY S2420 Connect to-
gether with
GA247ï24
and
GB3007ï20
GB3000ï20 A 11GBïJ1:X1 RSD20 306VSïRJ S2016 Connect to-
gether with
GB3016ï20
GB3005ï20 A 11GBïJ1:B2 RSD20 2VSïBX S2420 Connect to-
gether with
GA260ï24
and
GA3000ï24
GB3006ï20 A 11GBïJ1:C1 RSD20 306VNPïB:3 TJB16
GB3007ï20 A 11GB−J1:C2 RSD20 2VSïBY S2420 Connect to-
gether with
GA247ï24
and
GA3001ï24
GB3009ï20 A 11GBïJ1:X2 RSD20 306VSïRF S2016 Connect to-
gether with
GB3012ï20
GB3012ï20 A 10GBïJ1:B3 RSD20 306VSïRF S2016 Connect to-
gether with
GB3009ï20
GB3016ï20 A 11GBïJ1:B1 RSD20 306VSïRJ S2016 Connect to-
gether with
GB3000ï20
GB3017ï20 306VSïRG S2016 94VPïP4:B16 MS20S Connect to-
gether with
GB3018ï20
GB3018ï20 306VSïRG S2016 306VSïRJ S2016 Connect to-
gether with
GB3017ï20

### Page 5

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 5 of 20
NOTE: Make a new screen connection 94VP ïP4:803 to make space for the new splice
306VSïRG.
(5) In the RH electrical center 306VU, install the relay 11GB (601). (Ref. AMM TASK
31ï15ï10ï400ï801) (Ref. Fig. 5 view CïC and E.
(6) Install the marker decal 11GB adjacent to the relay (601).
(7) Assemble the connector 94VP ïP4 (Ref. WDM 20ï30ï15).
(8) Connect and attach the connector 94VP ïP4.
D. FUNCTIONAL TEST
(1) Prepare for the functional test.
(a) Connect the LH, RH and CTR Battery (Ref. AMM TASK 24 ï00ï00ï860ï806).
(b) Supply the external AC power (Ref. AMM TASK 24 ï00ï00ï860ï801).
(c) Inspect and Correct if necessary the Oil Level in System 2b and 2a Hydraulic Reservoir
(Ref. AMM TASK 12ï20ï29ï200ï801).
(d) Lift the Aircraft on the Three Main Jacks (Ref. AMM TASK 07 ï10ï00ï582ï807).
WARNING: YOU MUST INSTALL THE FARADAY CAGE TO THE SEPARATION BOLT.
INJURY TO PERSONS CAN OCCUR IF THE SEPARATION BOLT
ACCIDENTALLY DETONATES.
WARNING: YOU MUST WEAR SAFETY GLASSES AND EAR PROTECTORS WHEN
YOU REMOVE THE CONNECTOR ON THE SEPARATION BOLT. INJURY TO
PERSONS CAN OCCUR IF THE SEPARATION BOLT ACCIDENTALLY
DETONATES.
(e) On the LH circuit breaker panel 9VU, open the circuit breaker L LDG EMER RELEASE
(E12).
(f) On the RH circuit breaker panel 10VU, open the circuit breaker R LDG EMER RELEASE
(L11).
(g) In the LH Main Landing Gear bay, disconnect the connector 3GB ïP1 from the separation
bolt.
(h) Install blanking caps on the connector 3GB ïP1.
(i) Install a Faraday cage on the connector on the separation bolt.
(j) In the RH Main Landing Gear bay, disconnect the connector 4GB ïP1 from the separation
bolt.
(k) Install blanking caps on the connector 4GB ïP1.
(l) Install a Faraday cage on the connector on the separation bolt.
(m) On the LH circuit breaker panel 9VU, close the circuit breaker L LDG EMER RELEASE
(E12).
(n) On the RH circuit breaker panel 10VU, close the circuit breaker R LDG EMER RELEASE
(L11).
(o) Put a warning sign ” KEEP CLEAR OF THE LANDING GEAR ” adjacent to the aircraft.
(2) Do the functional test.
WARNING: BE CAREFUL WHEN YOU OPERATE THE LANDING GEAR. MAKE SURE
PERSONS ARE NOT NEAR THE LANDING GEAR. WHEN THE LANDING GEAR
MOVE IT CAN CAUSE INJURY TO PERSONS.
NOTE: During the test in step (2) (a) thru (2) (n) the position of the landing gear handle and
the landing gear position arrows may be out of sync and the caution GEAR CONFIG
and GEAR FAULT may occur. This can be ignored.

### Page 6

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 6 of 20
ACTION RESULT
(a) On the overhead panel
HYDRAULIC (27VU), set the
pushbutton L DC PUMP to OFF.
(b) Release pressure in hydraulic
accumulators for system 1 (Ref.
AMM TASK 29ï10ï00ï860ï803)
(c) Remove landing gear safety pins
(Ref. AMM TASK
32ï00ï00ï000ï801)
(d) Pressurize the hydraulic system
2 (Ref. AMM TASK
29ï10ï00ï860ï801).
(e) Move the landing gear handle to
the UP position.
The landing gears retract.
(f) On the LH circuit breaker panel
9VU, open the circuit breaker L
LDG CTL (F11).
(g) In front of the co ïpilots control
column, pull the emergency
release handle.
The main landing gear extend.
The nose landing gear stays in retracted
position.
On the EICAS display, the two green main
landing gear DN symbols are shown.
(h) Move the landing gear handle to
the down position.
(i) On the LH circuit breaker panel
9VU, close the circuit breaker L
LDG CTL (F11).
The nose landing gear extends.
(j) On the overhead panel
HYDRAULIC PANEL 27VU, set
the switch HYDRAULIC PUMP
C/R AC to the OFF position.
(k) Install the landing gear safety pin
on the nose landing gear (Ref.
AMM TASK
32ï00ï00ï400ï801).
(l) In the nose wheel well, manually
turn the crank on the
emergencyïuplock release valve
to the usual position (make sure
the emergency release switch is
not activated).
(m) In the flight compartment, make
sure the emergency release
handle is in the usual position.

### Page 7

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 7 of 20
ACTION RESULT
(n) Do step (c) thru (m) again four
times.
(o) Install snap wire on the
emergency release handle.
(3) Check voltage in separation bolts 3GB ïP1 and 4GBïP1
(a) Install the landing gear safety pin on the main landing gear (Ref. AMM TASK
32ï00ï00ï400ï801).
(b) Remove the blanking caps from the connectors 3GB ïP1 and 4GBïP1.
(c) In 3GB ïP1, use a multimeter and check the voltage on pin A, B, C and D against a
suitable ground. Make sure there are no  28VDC on any of the pins.
(d) In 4GB ïP1, use a multimeter and check the voltage on pin A, B, C and D against a
suitable ground. Make sure there are no  28VDC on any of the pins.
(4) Restore the separation bolts and continue the test.
(a) On the LH circuit breaker panel 9VU, open the circuit breaker L LDG EMER RELEASE
(E12).
(b) On the RH circuit breaker panel 10VU, open the circuit breaker R LDG EMER RELEASE
(L11).
(c) In the LH main landing gear bay,
1 Remove the Faraday cage from the connector on the separation bolt.
2 Connect the connector 3GBïP1 to the separation bolt.
(d) In the RH main landing gear bay.
1 Remove the Faraday cage from the connector on the separation bolt.
2 Connect the connector 4GBïP1 to the separation bolt.
(e) On the LH circuit breaker panel 9VU, close the circuit breaker L LDG EMER RELEASE
(E12).
(f) On the RH circuit breaker panel 10VU, close the circuit breaker R LDG EMER RELEASE
(L11).
(g) Do the electrical continuity test of the separation bolt (Ref. AMM TASK
32ï32ï20ï760ï801).
(h) Remove all landing gear safety pins from the nose landing gear and main landing gear.
(Ref. AMM TASK 32ï00ï00ï000ï801).
(i) Do the Functional Test of the Extension and Retraction of the Landing Gears (Ref. AMM
TASK 32ï30ï00ï720ï801).
(j) Install all landing gear safety pins (Ref. AMM TASK 32 ï00ï00ï400ï801).
(5) Do the following tests to verify functionality after disconnection/connection of 94VP ïP4.
(a) Do the operational test of the TRU (Ref. AMM TASK 24 ï31ï10ï710ï801).
(b) Operational test of the STBY ROLL trim signal.
ACTION RESULT
1 In the flight compartment,
on the panel 35VU:
ï Operate the STBY ROLL
trim switch to the left and
hold it in that position for
min. 30 seconds.
On the SED, The ROLL trim indicator
shows the RH trim in the fully up position.

### Page 8

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 8 of 20
ACTION RESULT
2 Operate the STBY ROLL
trim switch to the right and
hold until the actuator
stops.
On the SED, The ROLL trim indicator
shows the RH trim in the fully down
position.
(c) Do the continuity check of the fire handle/GCU signal.
ACTION RESULT
1 On the RH circuit breaker
panel 8VU, open tag and
safety the circuit breaker
FUEL R FIRE VLV (R20).
2 On the RH circuit breaker
panel 10VU, open tag and
safety the circuit breaker
HYDRAULIC R SHUT OFF
VLV (M12).
3 In the RH nacelle,
disconnect the connector
4XAïP2 from the generator
control unit.
4 Pull the R ENG fire handle.
5 Use the multimeter and
measure between
4XAïP2:H and A/C ground.
4XAïP2:H is open to ground (100k:min).
6 Push the R ENG fire
handle.
7 Use the multimeter and
measure between
4XAïP2:H and A/C ground.
4XAïP2:H is connected to ground (10 :
max).
8 Make sure the safety locks
engage the R ENG fire
handle.
9 Connect the connector
4XAïP2 to the generator
control unit.
10 On the RH circuit breaker
panel 8VU, remove the tag
and close the circuit breaker
FUEL R FIRE VLV (R20).
11 On the RH circuit breaker
panel 10VU, remove the tag
and close the circuit breaker
HYDRAULIC R SHUT OFF
VLV (M12).

### Page 9

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 9 of 20
E. JOB CLOSE ïUP
(1) Lower the Aircraft and Remove the Three Main Jacks (Ref. AMM TASK 07 ï10ï00ï582ï808).
(2) Remove all the tools and the equipment from the work area. Make sure the work area is clean.
(3) Install the access panels.
ï 114AZ
ï 118AR
ï 466AZ.
(4) Remove the external AC power (Ref. AMM TASK 24 ï00ï00ï860ï802).
(5) Remove all the tools and the equipment from the work area. Make sure the work area is clean.

### Page 10

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 10 of 20
3. MATERIAL INFORMATION
A. Modification Kit No SAAB 2000 ï32ï081ï01 contains:
Item Part Number Qty Nomenclature Designation Remarks
601 M83536/6 ï022L
O/T
M83536/6ï022M
O/T
16303ï804ïG3Nï2
YE3
O/T
16303ï804ïG3Nï2
EE0
1 Relay ï 11GB
602 RSE120060
O/T
S220ïA4A0
O/T
SE405ï01.04.01
1 Relay Socket ï 11GBïJ1
603 D ï101ï00 1 Solder Sleeve 94VP ïP4:803
ï 55T8015ï24ï9 500mm Wire GA3000 ï2401
ï 55T8015ï24ï9 500mm Wire GA3001 ï2401
ï 55A0811ï20ï9 300mm Wire GB70 ï2001 If necessary
ï 55A0811ï20ï9 300mm Wire GB3000 ï2001
ï 55A0811ï20ï9 2000mm Wire GB3005 ï2001
ï 55A0811ï20ï9 3000mm Wire GB3006 ï2001
ï 55A0811ï20ï9 2000mm Wire GB3007 ï2001
ï 55A0811ï20ï9 1000mm Wire GB3009 ï2001
ï 55A0811ï20ï9 500mm Wire GB3012 ï2001
ï 55A0811ï20ï9 300mm Wire GB3016 ï2001
ï 55A0811ï20ï9 300mm Wire GB3017 ï2001
ï 55A0811ï20ï9 2000mm Wire GB3018 ï2001
S2420 D ï436ï36 2 Butt splice ï 2VSïBX
2VSïBY
S2016 D ï436ï37 3 Butt splice ï 306VSïRF
306VSïRG
306VSïRJ
RSD20 M39029/101 ï553 7 Contact ï 10GBïJ1
11GBïJ1
MS20S CTA ï0165 3 Contact ï 94VPïP4
TJB16 YHMM16 ï5DB8 1 Terminal Junction ï 306VNP

### Page 11

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 11 of 20
Item RemarksDesignationNomenclatureQtyPart Number
ï 6127432−016
O/T
IT18R.NN
O/T
IT18RNN901
O/T
lT18RNN3P
1 Marker plate ï 94VPïP4
ïï 1 Marker decal 11GB ïJ1
ïï 1 Marker decal 11GB
ïï 1 Marker decal 94VP ïP4
ï RNF100 3/16 1 Marker sleeve 2VS ïBX
ï RNF100 3/16 1 Marker sleeve 2VS ïBY
ï RNF100 3/16 1 Marker sleeve 306VS ïRF
ï RNF100 3/16 1 Marker sleeve 306VS ïRG
ï RNF100 3/16 1 Marker sleeve 306VS ïRJ
B. Local supply
Item Part Number Qty Nomenclature Designation Remarks
ï NITTO 665 AR Silicone Tape ï Or equivalent
ïï AR Lacing cord ïï
ïï AR Cable ïtie ïï
ïï AR Snap wire, Brass,
0.02 in (0.5 mm) di-
ameter.
For emergency
release handle.

### Page 12

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 12 of 20
Wiring Diagram System GA ï PRE MOD
FIG. 1
B23835
J G
A2
R
B2A2A1 B1
A5
L
1
HP
2 134
XW V U
TKMS N
GA264ï24 GA262ï24
GA162ï24
GA116ï24
GA104ï24
GA105ï24
GA246ï24
GA246ï24
GA249ï24
GA249ï24
GA242ï24GA242ï24
GA245ï24GA245ï24
GA248ï24
GA247ï24
GA261ï24
GA260ï24
GA109ï24GA244ï24
GA243ï24 GA108ï24
GA111ï24
GA115ï24
GA114ï24
GA113ï24
GA112ï24
SHT 2
2VS V
B3A3
MH
X1 X2
2VS AC
2VS AB
DGLL
CB F E D
6VP
P1
J1
CONTROL VALVE
LANDING GEAR
15GA
J2
P2
CONTROL PANEL
B
4VNP
6MH
J1
1VU CENTER INSTR PANEL
1GA LANDING GEAR
95VP
P1
P1
B23835
PART OF DWG REF.  7332390ï801    SHEET 1 OF 5    REV.
PART OF DWG REF.  7332390ï504    SHEET 1 OF 5    REV. E
PART OF DWG REF.  7332390ï802    SHEET 1 OF 5    REV.
B19
B18
B20
B13
GA248ï24
GA247ï24
GA261ï24
GA260ï24
94VP
P4 J4

### Page 13

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 13 of 20
Wiring Diagram System GA ï POST MOD
FIG. 2
B23865
B23865
DWG REF.  7332390ï803    SHEET 1 OF 5    REV. A

### Page 14

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 14 of 20
THIS PAGE INTENTIONALLY LEFT BLANK

### Page 15

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 15/16 of 20
Wiring Diagram system GB ï PRE MOD
FIG. 3
B23834
8A 8A
B14
2
2
B1
B2
B1
B2
A7
9
922 922
922
922
922
922922 922
806801
801
801
801 801
982
982
803 803
B17
B16
805
FF
DD
1002
1002
804
GG
AA
1002
G
H
F
E
X2
X1
A2
A3
B2
B3
D
X2
C
X1
B
A1
A
B1
A3
B3
B2
A2
G
Y
H
L
N
P
R
S
T
11
12
10
8
9
7
5
6
4
3
2
1
804
803
1001
B
A
C
D
GG
AA
801
802 1001
C
D
B
A
1001
10011002
DD
FF
801
802
B3
B2
A6
L/1
5 B11
B106
L/1
WH
BK
WH
BK
GB1295ï24
GB2295ï24GB104ï24
GB104ï24
GB103ï24
GB15ï20
GB15ï20
GB51ï20
GB51ï20
GB14ï20
GB14ï20
GB98ï20
GB98ï20
GB100ï20
GB100ï20
GB43ï22
GB41ï22
GB42ï22
GB40ï22
GB38ï22
GB39ï22
GB37ï22
GB35ï22
GB36ï22
GB34ï22
GB33ï22
GB32ï22
GB101ï20GB101ï20
GB96ï20 GB96 ï20
GB78ï20
GB78ï20
BKBK
WH
BK
WH
WH
WHWH
BK
BK
WH
BK
BK
WH
BK
WH WH
BK
WH
BK
BK
WH
BK
WH WH
BK
WH
BK
GB584ï20
GB587ï20
GB690ï20
GB693ï20
GB102ï20
GB31ï20
GB19ï20
GB19ï20
GB10ï20
GB10ï20
GB6ï20
BK
GB72ï20
WH
BK
WH
BK
WH
BK
WH
BK
WHWH
BK
GB5ï20
GB5ï20
GB97ï20
GB8ï20
GB8ï20
GB9ï20
GB9ï20
GB59ï20
GB52ï20
GB52ï20
GB70ï20
GB73ï20
GB80ï20
GB80ï20
GB71ï20 GB75ï20
GB77ï20
GB83ï20
GB82ï20
GB81ï20
GB79ï20
GB76ï20GB74ï20
GB57ï24
GB16ï20
GB16ï20
GB61ï20
GB62ï20
GB60ï20
GB56ï20
GB56ï20
GB55ï20
GB55ï20
GB54ï20
GB54ï20
GB53ï20
GB53ï20
GB58ï24
GB12ï20
GB1 1ï20
BK
WH
GB20ï20
GB20ï20
GB18ï20
GB18ï20
GB30ï20
GB2ï16 GB4ï20
WH
BK
GB3ï20GB1ï16
1VS T
(LOCKED DOWN)
GA
X1
X2
B3
306VSAM
306VSAL
(LOCKED DOWN)
NOTE
HARNESS RH
CEILING
EMER RELEASE
EMER RELEASE
B3
1
1
1
GA
X2
X1
306VS T
306VS R
306VS M
+28VDC
+28VDC
NOTE
B3
B2
B1
A3
A2
A1
X2
X1
10A
10A
LH BAT BUS
L LDG
PP
RH BAT BUS
PP
R LDG
DWG REF.  7332391ï502    SHEET 1 OF 1    REV. C
J1C J1C203VU
P26 J26
AVIONICS RACK203VU
2TL1TL
204VNP
18GA
J1
J1
305VNP
A
21GA
J1
P1
95VP
J3P3
95VP
EXPLN BOLT
EXPLN BOLT
414VS E
412VS A
306VU
RH ELECTRICAL CENTER
200VNP
LH ELECTRICAL CENTER
305VU
TEST
EXPL BOLT
8GB
J1
J4P4
P1J1
3GB
L MLG DOOR
LEFT WING
RIGHT WING
FUSELAGE
4GB
R MLG DOOR
94VPP1 J1
P1J1
135VP
J1
5GB
6VP
J1
J1
10GB
6GB
9VU
H
9VT
LH CB PANEL
1GB J2P2
9VU
136VP
P1
P1
J2P2
10VU
C
10VT 2GB
10VU
RH CB PANEL
B23834

### Page 16

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000ïXXïXXX
Page 16

### Page 17

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 17/18 of 20
Wiring Diagram system GB ï POST MOD
FIG. 4
B23925
B23925
DWG REF.  7332391ï801    SHEET 1 OF 1    REV. D

### Page 18

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000ïXXïXXX
Page 18

### Page 19

Service Bulletin
11 August 2020
 
2000ï32ï081
Page 19/20 of 20
Harness Routing and Component Location
FIG. 5
B23907
B23907
DWG REF.  7392491ï666   SHEET 1 OF 1   REV. .J

### Page 20

Service Bulletin
Date Month Year
Revison X, Date Month Year
2000ïXXïXXX
Page 20

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
