# Schempp-Hirth Technical Note 868-4/890-5

Copy: No revision named ("Schempp-Hirth Technical Note 868-4_890-5 with Appendix"), 9 pages: PDF https://openairdocs.org/files/sha256/41/26/41264b677326abb008080a8949b5e15bf18a57a81b95ca7489616b67010e6e56; text https://openairdocs.org/service-documents/schempp-hirth/tn-868-4-890-5/file/41264b677326.md. Rights: © Schempp-Hirth. Filed by the FAA in regulations.gov docket FAA-2024-2135; AD 2025-04-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Schempp-Hirth](https://openairdocs.org/service-documents/schempp-hirth.md)
- Type: Other document (Technical Note)
- Number: 868-4/890-5
- Page: https://openairdocs.org/service-documents/schempp-hirth/tn-868-4-890-5

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2025-04-14](https://openairdocs.org/ad/2025-04-14.md), effective Apr 8, 2025: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/schempp-hirth/tn-868-4-890-5/proposed.md).

## Text (9 pages)

Rights: © Schempp-Hirth. Filed by the FAA in regulations.gov docket FAA-2024-2135; AD 2025-04-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

SCHEMPP-HIRTH  Technical Note  Page No.  01
Flugzeugbau GmbH.  No. 868 - 4
Kirchheim/Teck  No. 890 - 5  No. of pages 02
SUBJECT:  Canopy locking mechanism
AFFECTED:  Powered Sailplane Nimbus-4DT (TC-No. 868)
S/N 1 through 12
Powered Sailplane Nimbus-4DM (TC-No. 868)
S/N 1 through 58
Powered Sailplane Duo Discus T (TC-No. 890)
S/N 1 through 96
URGENCY  Recommended before/at next annual inspection
REASON:  - A sailplane type has experienced fuselage deformation resulting
from acceleration which perhaps lowered the friction in the
canopy locking mechanism. It may then be possible for the canopy
locking mechanism to move into the open position.
In an other case the canopy opened shortly after take-off on aero-
tow. But it cannot ruled out that the canopy with locked mechanism
was placed on the fuselage pins instead being connected with the
pins and fuselage.
For this case a red mark on the canopy frame should placed which
is not visible when the canopy is correct closed on the fuselage frame.
ACTIONS:  1. Nimbus-4DT, Nimbus-4DM
A compression spring will installed in the canopy locking mechanism
will ensure that the locking mechanism is always moved in the closed
position.
The retrofit of the spring is done in accordance with the working
instruction in the appendix (if not yet done).
2. Nimbus-4DT, Nimbus-4DM
To increase the friction in the canopy locking mechanism spring
washers are fitted to both levers, see working instruction in
the appendix (if not yet done).
12

### Page 2 (OCR)

SCHEMPP-HIRTH  Technical Note  Page No.  02
Flugzeugbau GmbH.  No. 868 - 4
Kirchheim/Teck  No. 890 - 5  No. of pages 02
ACTIONS (ctd.):  3. Nimbus-4DT, Nimbus-4DM, Duo Discus T
A magnet is mounted on the front lever. In the locked position the
magnet is flush on the operating rod and produce an additional retention
The installation of the modified front lever and the adjustment of
the magnet is done in accordance with the working instruction in the
appendix.
4. Nimbus-4DT, Nimbus-4DM, Duo Discus T
The canopy frame will painted on two areas on the inner side, see
drawing in the appendix.
This marks are masked by the fuselage frame when the canopy is correct
closed.
MATERIAL:  Item 1:  1 Compression spring  1,25 × 10 x 64 × 12,5 mm
1 Bushing  Drawing No. S14 RB 800
1 Hose clamp  S9/9ZY VPE 100 (Norma)
1 guide (if required)  Part 13 in Drawing No. S14RB805
1 screw (if required)  M4x30 DIN 84
1 locking nut (if required)  M4
Item 2:  2 Spring washers (waved) DIN 137-B8-Fst
2 Lock nuts (flat) M6
2 Lock nuts (flat) M5
2 washers DIN 988, 6 × 12 × 0,5 mm
Item 3:  1 Magnet 37513 Magma-C or
1 front lever with magnet (Drawing No. S14 RB 802)
Item 4:  2-component coating RAL 2004 (orange)
WEIGHT:  No change
C/G POSITION:  No change
Note:  1. This issue supersedes the Technical Note No. 868-4,
dated July 4", 2001.
2. Actions may be accomplished by an experienced person
and entered in the log book at the occasion of the next
annual inspection.
Kirchheim/Teck, 15.02.2005  LBA-approved:  EASA approved on:
The German original has been  23.02. 2005
and is signed of by Mr.  date of.....  under Approval No.:  2005 - 1925
Issued:  vul  done by best knowledge and  The translation into English has been
( Treiber)  judgement.

### Page 3 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  01
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
Mounting of a compression spring in the canopy locking mechanism
Remark:
At earlier S/Nos the guide for the locking mechanism is perhaps missing.
a) Mount the guide.
b) Drill a 4mm hole from underneath 15mm from the inner end of the guide.
c) Mount a 4 mm screw with a locking nut.
1. a) Shorten the spring ½ turn and file the wire end.
b) Turn spring (with the filed wire end) on the mechanism in front of the canopy
cross bar.
Apply spring diagonally and turn on by hand the last winding with the aid of a
needle-nose pliers.
2. Mount slotted bushing (with the flange aft) on the locking mechanism forward
of the compression spring.
3. Slide the open hose clamp (fixed nut outside) on the locking mechanism and mount
it on the bushing.
4. a) Open locking mechanism fully.
b) Compress the spring fully.
c) Tighten the hose clamp so that the bushing will not move, see photo
15 mm

### Page 4 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  02
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
Mounting of the spring washers at the canopy actuating levers
Forward actuating lever:
1. Remove stop-nut at the lever.
2. Dismount connection between the actuating mechanism.
3. Dismount the actuating mechanism.
4. Remove lever from the hinge point without brass bushing.
5. Insert waved spring washer on brass bushing.
6. Install lever on brass bushing with waved spring washer below.
7. Mount washer (0,5 mm) and new stop-nut at lever hinge point.
8. Connect actuating mechanism and mount it on the lever again.
Aft actuating lever
9. Remove stop-nut at the lever.
10. Remove lever from the hinge point without brass bushing.
11. Insert waved spring washer on brass bushing.
12. Install lever on brass bushing with waved spring washer below.
13. Mount washer (0,5 mm) and new stop-nut at lever hinge point.

### Page 5 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  03
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
Front actuating lever with magnet
1. Remove front lever refer to item 1 through 5 on page 02.
2. a) Modified lever according drawing on page 04. Paint it and mount magnet
or
b) order a modified lever with magnet from the manufacturer or the manu-
facturer modify the lever.
c) Mount lever with magnet.
3. Adjustment of the magnet and hints
The magnet must be adjusted that no spring-back is in the actuating mechanism
and the magnet is flush to the operating rod, see photo "front canopy locking
mechanism 4".
To reach this adjustment it should be required:
a) to grind the corners at the lugs of the actuating rods at the front and aft levers,
see photo "aft canopy locking mechanism 1".
b) if the lugs running not parallel to the rods:
The lugs should be bent parallel to the actuating direction of the levers, see
photo "front canopy locking mechanism 3".
c) If the magnet with locked actuating mechanism is not flush to the rod, the rod
must be bent parallel to the magnet surface, see photo ifront canopy locking
mechanism 2".
4. With the magnet and the actuating mechanism correct adjusted a small retention
force is noticeable.
The connection of the magnet is secured with Loctite i.e. No. 243 (blue).
Remark:
The magnet force is only effective if the gap is less than 1 mm.
Therefore the magnet must be flush with the rod for the highest retention force.
An example for insufficient adjustment of the magnet and the rod is shown on
photo "front canopy locking mechanism 2".

### Page 6 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  04
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
magnet
4.6 mm  0.181 in.
61 mm
2.40 in.
M5
49 mm
modification  1.93 in.

### Page 7 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  05
Flugzeugbau Gmbh.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
corner jams with
locked lever
aft canopy locking mechanism 1
magnet not flush to the rod;
no retention force at the lever
front canopy locking mechanism 2

### Page 8 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  06
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
lug skewed;
not parallel bent
front canopy locking mechanism 3
magnet must be flush
and without tension
on the rod
front canopy locking mechanism 4

### Page 9 (OCR)

SCHEMPP-HIRTH  Appendix to  Blatt:  07
Flugzeugbau GmbH.  Technical Note
Kirchheim/Teck  No. 868 - 4 / 890 - 5  Blattz.:  07
front instrument
panel
100 mm
3.94 in.
150 mm
5.91 in.
red mark
front and aft
inside left canopy frame

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
