# Sikorsky Alert Service Bulletin 76-66-50

Copy: No revision named ("Sikorsky ASB 76-66-50"), 18 pages: PDF https://openairdocs.org/files/sha256/8f/1d/8f1d7716e6a2a9c6aeb9edfa900a64d6357e80e23e0b24703d728dddb651d804; text https://openairdocs.org/service-documents/sikorsky/sb-76-66-50/file/8f1d7716e6a2.md. Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2014-0335, the docket of AD 2015-26-10. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Sikorsky](https://openairdocs.org/service-documents/sikorsky.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 76-66-50
- Page: https://openairdocs.org/service-documents/sikorsky/sb-76-66-50

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/sikorsky/sb-76-66-50/proposed.md).

## Text (18 pages)

Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2014-0335, the docket of AD 2015-26-10. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Sikorsky  Sikorsky Aircraft Corporation
A United Technologies Company  6900 Main Street P.O. Box 9729
Stratford, Connecticut 06615-9129
(203) 386-4000
S-76® HELICOPTER
ALERT SERVICE
BULLETIN
NOTICE TO ALL PERSONS RECEIVING THIS DOCUMENT:
WARNING: THIS DOCUMENT, OR AN EMBODIMENT OF IT IN ANY MEDIA, DISCLOSES INFORMATION WHICH IS PROPRIETARY, IS THE PROPERTY OF SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES, IS
AN UNPUBLISHED WORK PROTECTED UNDER APPLICABLE COPYRIGHT LAWS, AND IS DELIVERED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED, DISCLOSED, REPRODUCED, IN WHOLE OR IN PART
(INCLUDING REPRODUCTION AS A DERIVATIVE WORK), OR USED FOR MANUFACTURE FOR ANYONE OTHER THAN SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES WITHOUT ITS WRITTEN CONSENT,
AND THAT NO RIGHT IS GRANTED TO DISCLOSE OR SO USE ANY INFORMATION CONTAINED HEREIN. ALL RIGHTS RESERVED. ANY ACT IN VIOLATION OF APPLICABLE LAW MAY RESULT IN CIVIL AND CRIMNAL
PENALTIES.
EXPORT WARNING: THESE COMMODITIES, TECHNICAL DATA OR SOFTWARE ARE SUBJECT TO THE EXPORT CONTROL OF EITHER THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (ITAR) OR THE EXPORT
ADMINISTRATION REGULATIONS (EAR) AND CANNOT BE EXPORTED WITHOUT THE PRIOR AUTHORIZATION OF EITHER THE DEPARTMENT OF STATE OR THE DEPARTMENT OF COMMERCE. THE TERM "EXPORT
INCLUDES ANY DISCLOSURE AND/OR PROVISION OF ACCESS TO COMMODITIES, TECHNICAL DATA OR SOFTWARE TO OR BY FOREIGN NATIONALS (WHETHER LOCATED IN THE UNITED STATES OR ABROAD). THIS
REQUIREMENT ALSO APPLIES TO FOREIGN NATIONAL EMPLOYEES OF U.S. COMPANIES AND THEIR FOREIGN SUBSIDIARIES.
S-76 IS A REGISTERED TRADEMARK OF SIKORSKY AIRCRAFT CORPORATION.
ASB 76-66-50
Basic Issue • January 14/13
SUBJECT: POWERTRAIN - Main Gear Box- One Time Inspection of Main Gear Box (MGB) Lower
Housing
Section 1. PLANNING INFORMATION
A.  Effectivity  All S-76A, B, and C model helicopters with the following MGB.
Component: MGB Series: 76351-09000 series, 76351-09500 series, and 76351-
09600 series, modified by Overhaul Repair Instruction (ORI)
numbers; 76350-065, TS-065-II, TS-065-IIA, TS-065-2, or TS-065-
2A.
B. Purpose  To determine if MGB lower housing has been modified by Overhaul Repair
Instruction (ORI) number(s) listed above. If any of these ORI number(s) are
present, perform Alert Service Bulletin (ASB). If none of these ORI number are
present, no further action is required.
Background:
Investigations for loss of MGB oil pressure during flight revealed that the ORI
repair procedure for the MGB lower housing jet bore(s) was not properly
implemented.
ONE-TIME  ATA
INSPECTION  66-10-00  Page 1 of 18

### Page 2 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 1.  PLANNING INFORMATION (Continued)
C. Description  The MGB lower housing is accessed and a visual inspection is performed using a
flashlight and mirror to determine if ORI numbers listed in Effectivity section of this
ASB was performed on the MGB lower housing. If the lower housing is found to
have been repaired by ORI numbers listed in Effectivity section an inspection is
required on all ten (10) lower housing jet bores for leaks, paint or caulk blistering,
and liner protrusion. If any of these conditions are found, no further flight is allowed
until the repair(s) is completed.
D. Compliance  Compliance is essential. The one-time inspection outlined herein shall be
accomplished by March 31, 2013.
E. Approval  Inspection Item.
F. Manpower (Estimated)
Task  No. of Men  No. of Hours  Man-Hours*
Inspect Jet Bore for Oil Leakage  1  0.2  0.2
Inspect Jet Bore for Bubbling/Blistering of  1  0.2  0.2
Caulk and Paint
Inspect Liner for Protrusion/Movement  1  0.2  0.2
Leak Check  1  0.5  0.5
Total Man-Hours  1.1  1.1
*Estimate does not include time required to prepare helicopter or return it to flight status.
G. Material
None.
H. Tooling
Qty  Nomenclature  Part No.  Source
1  Plastic Scraper  Commercially Available or equivalent  (1)
Inspection mirror  Commercially Available or equivalent  (1)
1  Flash Light  Commercially Available or equivalent  (1)
(1) Procure from local supply
Weight and Balance
Not affected.
J.  Electrical Load Data
Not affected.
ATA  ONE-TIME
Page 2  66-10-00  INSPECTION

### Page 3 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 1. PLANNING INFORMATION (Continued)
K. Software Load Data
None.
L.  References
None.
M. Publications Affected
(1) S-76A Model Helicopters:
(a) Temporary Revision No. 5-189 against Airworthiness Limitations and Inspection
Requirements Manual, SA 4047-76-2-1, Chapter/Section 5-20-00, Before First Flight
of the Day Inspection Checklist, is issued concurrently with this ASB.
Temporary Revision No. 66-49 against Maintenance Manual, SA 4047-76-2,
Chapter/Section 66-10-00, Main Gear Box - Inspection/Check, Before First Flight of
the Day Inspection of the MGB Lower Housing Jet Bores, is issued concurrently with
this ASB.
(2) S-76B Model Helicopters:
(a)  Temporary Revision No. 5-166 against Airworthiness Limitations and Inspection
Requirements Manual, SA 4047-76B-2-1, Chapter/Section 5-20-00, Before First
Flight of the Day Inspection Checklist, is issued concurrently with this ASB.
(b)  Temporary Revision No. 66-23 against Maintenance Manual, SA 4047-76B-2,
Chapter/Section 66-10-00, Main Gear Box - Inspection/Check, Before First Flight of
the Day Inspection of the MGB Lower Housing Jet Bores, is issued concurrently with
this ASB.
(3) S-76C Model Helicopters:
(a) Temporary Revision No. 5-169 against Airworthiness Limitations and Inspection
Requirements Manual, SA 4047-76C-2-1, Chapter/Section 5-20-00, Before First
Flight of the Day Inspection Checklist, is issued concurrently with this ASB.
(b)  Temporary Revision No. 66-26 against Maintenance Manual, SA 4047C-76-2,
Chapter/Section 66-10-00, Main Gear Box - Inspection/Check, Before First Flight of
the Day Inspection of the MGB Lower Housing Jet Bores, is issued concurrently with
this ASB.
N. Attachment
None.
ONE-TIME  ATA
INSPECTION  66-10-00  Page 3

### Page 4 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 2. MATERIAL INFORMATION
A. Basis for Material Data
Per helicopter.
B. Bill of Material
None.
C. Consumable Material
OBSERVE ALL CAUTIONS AND WARNINGS ON CONTAINERS
WARNING  WHEN USING CONSUMABLES. WHEN APPLICABLE, WEAR
NECESSARY PROTECTIVE GEAR DURING HANDLING AND USE. IF
A CONSUMABLE IS FLAMMABLE OR EXPLOSIVE, MAKE CERTAIN
CONSUMABLE AND ITS VAPORS ARE KEPT AWAY FROM HEAT,
SPARK AND FLAME. MAKE CERTAIN FIREFIGHTING EQUIPMENT
IS READILY AVAILABLE PRIOR TO USE. FOR ADDITIONAL
INFORMATION ON TOXICITY, FLASHPOINT AND FLAMMABILITY
OF CHEMICALS, CONSULT YOUR MEDICAL PEOPLE OR THE
MANUFACTURER OF THE CONSUMABLE.
Qty  Nomenclature  Part No.  Source
As Req'd  Acetone  ASTM D329  (1)
Ethyl Alcohol  (Alternate) A-A-53880  (1)
Dry-Cleaning Solvent  (Alternate) MIL-PRF-680, Type II or  (2)
equivalent
As Req'd  Caulk  AMS 3265, Class B  (1)
As Req'd  Clear Epoxy  MIL-PRF-22750  (1)
Clear Polyurethane  (Alternate) MIL-PRF-85285 or  (1)
equivalent
As Req'd  Cotton Cheesecloth  CCC-C-440  (1)
Crocus Cloth  (Alternate) A-A-1206  (1)
Low-Lint cleaning Cloth  (Alternate) A-A-59323, Type or  (1)
equivalent
As Req'd  Dow 19  MIL-M-3171 Type VI or equivalent  (3)
As Req'd  Epoxy Primer  MIL-P-23377  (1)
Epoxy Primer  (Alternate) MIL-PRF-85582 or  (1)
equivalent
As Req'd  Gear box Oil  DOD-PRF-85734  (1)
Gear box Oil  (Alternate) MIL-L-23699 or equivalent  (1)
Gear box Oil  (Alternate) MIL-L-21260 Type I or  (1)
equivalent
Gear box Oil  (Alternate) Grade 30 or equivalent  (1)
ATA  ONE-TIME
Page 4  66-10-00  INSPECTION

### Page 5 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Qty  Nomenclature  Part No.  Source
Gear box Oil  (Alternate) Dexron III, ATF  (1)
As Req'd  Matching Paint (epoxy coating)  MIL-PRF-22750  (1)
As Req'd  Paint Stripper  TT-R-248 or equivalent  (1)
Paint Stripper  (Alternate) MIL-R-81294 or equivalent  (1)
As Req'd  Polyurethane Paint  MIL-PRF-85285, Color 17178  (1)
(1)  Procure through local supply.
(2)  Manufactured by Safety-Kleen Systems, Inc. 5400 Legacy Drive Cluster II, Building 3
Plano, Texas 75024 USA 1-800-669-5740 website: www.Safety-Kleen.com
Manufactured by DGR Industrial Products, Inc. 4435 North First Street, Suite #184
Livermore, California 94551, Phone: (408) 221-7122, website: www.chemical-
supermarket.com
Section 3. ACCOMPLISHMENT INSTRUCTIONS
A.  Prepare helicopter for inspection:
(1) Turn off all helicopter electrical and hydraulic power.
(2) Engage rotor brake.
B.  Perform one-time inspection to determine if the MGB lower housing was repaired per ORI
numbers listed in Effectivity section of this ASB, and record data (after inspection is completed)
via MGB Lower Housing Jet Bore Data Sheet: (Refer to Section H).
NOTE: The ORI number is marked with prefix 'TS-065'.
NOTE: If MGB lower housing has been repaired per any ORI numbers listed in Effectivity
section of this ASB, a recurring before first flight of the day inspection will be
implemented. Refer to Temporary Revisions listed in the Publications Affected
Section of this ASB, to perform Before First Flight of the Day Inspection of MGB
Lower Housing Jet Bores.
(1) Using a flashlight and mirror, inspect nameplate area for part markings on the lower
housing, center top, next to Accessory Drive pad. Refer to Figures 1 and 2.
(a) If the ORI numbers cannot be read, remove paint on part marking boss
only, See Figure 2.
(b) Thoroughly clean area with Acetone per ASTM D329, Ethyl Alcohol per A-
A-53880 or dry-cleaning solvent per MIL-PRF-680 Type Il and Crocus
Cloth per A-A-1206, Cotton Cheesecloth per CCC-C-440 or Low-Lint
Cleaning Cloth per A-A-59323, Type II.
(2) If part markings match any of the ORI numbers listed in Effectivity section of this ASB,
proceed to step (3). If part markings do not match any of the ORI numbers listed in
Effectivity section of this ASB, no further action is required. Proceed to Section E.
ONE-TIME  ATA
INSPECTION  66-10-00
Page 5

### Page 6 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
(3) Visually inspect all ten MGB lower housing jet bores and record data via MGB Lower
Housing Jet Bore Data Sheet. Refer to Figures 3 and 4 for jet bore locations for the
following inspections:
(a) Perform a visual inspection of each jet bore for any sign of the liner protrusion
and/or movement. Refer to Figures 5 and 6. If a jet bore liner appears to be
backed out by any amount, remove gear box. No further flight allowed until a
replacement gear box is installed.
(b) Perform a visual inspection for signs of oil leakage from the jet bore. If a leak is
present perform Section C. No further flight allowed until Section C. is performed.
(c) Perform a visual inspection for any sign of bubbling or blistering of paint and/or
caulking around jet bores. (Refer to Figure 8). If the paint and/or caulk is bubbling,
blistering or cracked, perform Section C. No further flight allowed until Section C. is
performed.
(d) If the anomalies above are not found and paint was removed from the part marking
area of the lower housing, proceed to Section F. If no paint was removed, proceed
to Section G.
C. Inspect jet bore for evidence of ORI 76350-065 liner repair as follows:
(1) Remove paint and caulking on and around jet bore with plastic scraper.
(2) Inspect for liner protrusion beyond end face of lower housing surface.
(a) If there is any indication of liner protrusion, replace gear box. (Refer to Figure 6).
(b)  If the liner is not protruding, continue with inspection. (Refer to Figure 5).
(3) Inspect liner parting line on end face. (Refer to Figure 5).
(a)  If oil is leaking between the ORI repaired liner and the housing, replace gear
box.
(b)  If oil is not leaking between the ORI repaired liner and the housing, continue with
inspection.
TAKE PRECAUTIONARY MEASURES NOT TO
CAUTION  INTRODUCE ANY FOREIGN OBJECTS INTO THE MGB
ASSEMBLY.
(4) Remove snap ring and jet from housing. Discard packing.
(5) Utilizing a film of gear box oil, install new packing on jet and install jet into housing. Refer
to Figure 7 for proper packing size and location.
(6) Perform a minimum of a 30 minute leakage check as follows:
ATA  ONE-TIME
66-10-00  INSPECTION
Page 6

### Page 7 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
(a) Perform a Ground Run as follows:
1. Operate the main rotor at 107% Nr flat pitch until indications are stable
for models S-76B and later. Operate the main rotor at 100% Nr flat pitch
until indications are stable for S-76A models.
2. Ground run the MGB until all fluids have reached normal operating
temperatures and then run for a minimum of 30 minutes.
3. Shutdown and perform a leak check per step (6)(b) prior to return to
service.
(b)  Visually inspect jet bores for visible moisture or droplets.
1. If leakage occurs, recheck packing installation, repeat steps (4) and (5).
If packing was not damaged during installation, remove and replace
gear box. If the new packing was damaged during installation, remove
and replace with new packing and repeat steps (4) through (6). If any
moisture or droplets of MGB oil are visible, MGB has failed leak check.
No further flight is allowed until MGB is replaced.
2. If no moisture or droplets of gear box oil is visible, MGB has passed leak
check.
(/)f the gear box passes the leak check, touch up inspected areas as follows:
(a)  Clean surface completely with Acetone per ASTM D329, or Ethyl Alcohol per A-
A-53880, or equivalent.
(b)  Apply a bead of caulk (AMS 3265 Class B) to all exposed interfaces.
(c)  Apply two (2) coats of epoxy primer (MIL-P-23377 or alternate MIL-PRF-85582
or equivalent).
(d) Apply two (2) coats of touch up paint (MIL-PRF 85285 Color No. 17178 or
equivalent).
Apply two (2) coats of clear epoxy (MIL-PRF-22750 or alternate MIL-PRF-85285
or equivalent).
Any MGB lower housings that are sent for overhaul or repair that are marked with ORI part
numbers listed in Effectivity section of this ASB, are to be repaired to ORI 76350-065 revision B
or later, regardless of the condition of repair. Re-identify lower housing per the new ORI revision
that was completed and obliterate old ORI 76350-065 part markings.
E. If no paint was removed from the part marking area of the lower housing, proceed to Section G.
If paint was removed from the part marking area of the lower housing, perform the following:
ONE-TIME  ATA
INSPECTION  66-10-00
Page 7

### Page 8 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
Thoroughly clean area with Paint Stripper TT-R-248 or MIL-R-81294, Acetone per ASTM
D329, Ethyl Alcohol per A-A-53880 or dry-cleaning solvent per MIL-PRF-680 Type Il and
Crocus Cloth per A-A-1206, Cotton Cheesecloth per CCC-C-440 or Low-Lint Cleaning
Cloth per A-A-59323, Type II.
NOTE: DOW 19 is to be applied per MIL-M-3171 Type VI. Refer to Material
Information section of this ASB.
Apply DOW 19 coating (or equivalent) with brush to any bare magnesium surfaces to
produce a brassy finish.
(3)  Apply two (2) coats of epoxy primer (MIL-P-23377 or alternate MIL-PRF-85582 or
equivalent).
(4) Apply two (2) coats of touch up paint (MIL-PRF-85285 Color No. 17178 or equivalent).
(5) Apply two (2) coats of clear epoxy (MIL-PRF-22750 or alternate MIL-PRF-85285 or
equivalent).
(6) Proceed to Section G.
G. Helicopter is returned to service.
ATA  ONE-TIME
66-10-00  INSPECTION
Page 8

### Page 9 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
H. MGB Lower Housing Jet Bore Data Sheet.
(1) Send this MGB Lower Housing Jet Bore Data Sheet, completed, via email to:
GPSIKSASProductSafet@utc.com or facsimile to: (860) 998-7565.
(2) Record the following information for each helicopter:
Customer/Operator Name:
Helicopter Serial Number:
Helicopter Total Time Since New:
Time Since Last Overhaul:
MGB Part Number:
MGB Serial Number:
Lower Housing Part Number:
Lower Housing ORI Part Number (TS-065-XX):
Lower Housing Serial Number: -
Any Sign of Liner Protrusion and/or Movement? YES  NO
Signs of Oil Leakage from any Jet Bore? YES  NO
Signs of Bubbling or Blistering Paint and/or Caulking around any Jet Bores? YES  _NO.
Date Inspection is Performed:
ONE-TIME  ATA
INSPECTION  66-10-00
Page 9

### Page 10 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
PART MARKING
(SEE FIGURE 2)
JET LOCATION
R.H. SHOWN
L.H. OPPOSITE
PART MARKING  (REF)  ACCESSORY DRIVE PAD
VIEW A-A
TD2975
PART MARKING BOSS LOCATION
FIGURE 1
ATA  ONE-TIME
66-10-00  INSPECTION
Page 10

### Page 11 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
REMOVE PAINT IN THIS
AREA TO FIND PART MARKING
800
E-SECRE
TREV O
TD2976
PART MARKING AREA ON LOWER HOUSING
FIGURE 2
ONE-TIME  ATA
INSPECTION  66-10-00
Page 11

### Page 12 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
GENERATOR  SPUR GEAR
GEAR JET BORE  JET BORE
FREE WHEEL
UNIT JET BORE -
BEVEL GEAR
JET BORE
FREE WHEEL UNIT (FWD)
ROLLER BRG JET BORE
TD2977
JET BORE LOCATIONS, RIGHT SIDE (LH SIDE IS OPPOSITE OF WHAT IS SHOWN)
FIGURE 3
ATA  ONE-TIME
66-10-00  INSPECTION
Page 12

### Page 13 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
- GENERATOR  GEAR JET  GENERATOR
GEAR JET
SPUR
SPUR  GEAR JET
GEAR JET
BEVEL
BEVEL  GEAR JET
GEAR JET
FREE WHEEL
-REE WHEE  JNIT JET  UNITJET
FREE WHEEL
FREE WHEEL  ROLLER  UNIT (FWD)
UNIT (FWD)  BRG JET
ROLLER
BRG JET
LEFT  RIGHT
TD2978
LOCATIONS OF JET BORES, BOTH SIDES
FIGURE 4
ONE-TIME  ATA
INSPECTION  66-10-00
Page 13

### Page 14 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
OIL JET
THE PARTING LINE IS THE INTERFACE
BETWEEN THE LINER AND THE HOUSING
LOWER
HOUSING
JET BORE LINER INSTALLED CORRECTLY
FLUSH TO 0.010 IN. BELOW HOUSING
OIL JET CROSS SECTIONAL VIEW
TD2979
JET BORE LINER
FIGURE 5
ATA  ONE-TIME
66-10-00  INSPECTION
Page 14

### Page 15 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
OIL JET
LOWER
HOUSING
JET BORE LINER
PROTRUSION
OIL JET CROSS SECTIONAL VIEW
TD2980
EXAMPLE OF A JET BORE LINER BACKED OUT
FIGURE 6
ONE-TIME  ATA
INSPECTION  66-10-00
Page 15

### Page 16 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3.  ACCOMPLISHMENT INSTRUCTIONS (Continued)
OUTBOARD PACKING
(LARGER DIAMETER)
NBOARD PACKING
SMALLER DIAMETER
(SEE FIGURE 4)  LOCATION  (SMALLER DIAMETER)  INBOARD PACKING  OUTBOARD PACKING  (LARGER DIAMETER)
GENERATOR GEAR  M83248 / 1-013  M83248 / 1-016
SPUR GEAR  M83248 / 1-133  M83248 / 1-226
BEVEL GEAR  M83248 / 1-137  M83248 / 1-232
FREE WHEEL UNIT (FWU) JET  M83248 / 1-011  M83248 / 1-016
FREE WHEEL UNIT (FWU)  ROLLER BRG JET  M83248 / 1-014  M83248 / 1-016  TD2888
PACKING LOCATIONS ON TYPICAL JET BORE
FIGURE 7
ATA  ONE-TIME
66-10-00  INSPECTION
Page 16

### Page 17 (OCR)

ASB 76-66-50  S-76 ALERT
Basic Issue • January 14/13  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
INSPECTION AREA FOR
BUBBLING OR BLISTERING
OF PAINT / CAULKING
OIL JET CROSS SECTION VIEW  TD2989
INSPECTION AREA
FIGURE 8
ONE-TIME  ATA
INSPECTION  66-10-00
Page 17

### Page 18 (OCR)

S-76 ALERT  ASB 76-66-50
SERVICE BULLETIN  Basic Issue • January 14/13
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
Record of compliance:
(1) Make helicopter logbook entries to show compliance with this ASB as follows:
(a) Make helicopter level logbook entry on form SA7343-15.
(b) When ASB modifies a component that can be removed from this helicopter:
1. Make component log card entries on forms SA7343-22 & SA7343-21 as
applicable.
2.  If a component modified by this ASB does not have a log card and the ASB
does not create one, then annotate compliance on the next higher assembly
that the component belongs to which does have a log card.
NOTE NEAR CONTEN COMPLACE  NOTE: If access to www.Sikorsky360.com is unavailable, complete attached ALERT
SERVICE BULLETIN COMPLIANCE RECORD CARD and return it to Sikorsky
Make an appropriate electronic compliance entry in the E-Notification section at
www.Sikorsky360.com. Refer to User Guide located on the www.Sikorsky360.com/E-
Notification Search page.
ATA  ONE-TIME
66-10-00  INSPECTION
Page 18

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
