# Sikorsky Alert Service Bulletin 76-66-52

Copy: No revision named ("Sikorsky ASB 76-66-52 Basic Issue"), 20 pages: PDF https://openairdocs.org/files/sha256/4b/9c/4b9ca3c36af74e98484469b47b21f323853193ca9172a24d08d1495c59e64d70; text https://openairdocs.org/service-documents/sikorsky/sb-76-66-52/file/4b9ca3c36af7.md. Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2015-0397; AD 2015-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Sikorsky](https://openairdocs.org/service-documents/sikorsky.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 76-66-52
- Page: https://openairdocs.org/service-documents/sikorsky/sb-76-66-52

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-04-05](https://openairdocs.org/ad/2015-04-05.md), effective Mar 12, 2015: No revision named

## Text (20 pages)

Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2015-0397; AD 2015-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

S-76® HELICOPTER 
ALERT SERVICE  
BULLETIN 
NOTICE TO ALL PERSONS RECEIVING THIS DOCUMENT: 
WARNING: THIS DOCUMENT, OR AN EMBODIMENT OF IT IN ANY MEDIA, DISCLOSES INFORMATION WHICH IS PROPRIETARY, IS THE PROPERTY OF SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES, IS 
AN UNPUBLISHED WORK PROTECTED UNDER APPLICABLE COPYRIGHT LAWS, AND IS DELIVERED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED, DISCLOSED, REPRODUCED, IN WHOLE OR IN PART 
(INCLUDING REPRODUCTION AS A DERIVATIVE WORK), OR USED FOR MANUFACTURE FOR ANYONE OTHER THAN SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES WITHOUT ITS WRITTEN CONSENT, 
AND THAT NO RIGHT IS GRANTED TO DISCLOSE OR SO USE ANY INFORMATION CONTAINED HEREIN. ALL RIGHTS RESERVED. ANY ACT IN VIOLATION OF APPLICABLE LAW MAY RESULT IN CIVIL AND CRIMINAL 
PENALTIES.   
EXPORT WARNING: THESE COMMODITIES, TECHNICAL DATA OR SOFTWARE ARE SUBJECT TO THE EXPORT CONTROL OF EITHER THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (ITAR) OR THE EXPORT 
ADMINISTRATION REGULATIONS (EAR) AND CANNOT BE EXPORTED WITHOUT THE PRIOR AUTHORIZATION OF EITHER THE DEPARTMENT OF STATE OR THE DEPARTMENT OF COMMERCE.  THE TERM “EXPORT” 
INCLUDES ANY DISCLOSURE AND/OR PROVISION OF ACCESS TO COMMODITIES, TECHNICAL DATA OR SOFTWARE TO OR BY FOREIGN NATIONALS (WHETHER LOCATED IN THE UNITED STATES OR ABROAD).  THIS 
REQUIREMENT ALSO APPLIES TO FOREIGN NATIONAL EMPLOYEES OF U.S. COMPANIES AND THEIR FOREIGN SUBSIDIARIES. 
S-76® IS A REGISTERED TRADEMARK OF SIKORSKY AIRCRAFT CORPORATION. 
ASB 76-66-52 
Basic Issue ▪ April 1/14 
SUBJECT: POWERTRAIN – Tail Drive Shaft – One-Time Inspection and Torque Verification of Tail 
Drive Shaft (TDS) Flange Bolt 
Section 3. PLANNING INFORMATION 
A. Effectivity All S-76A through D model helicopters up to and including serial number 761051  
  including spares. 
Component: All S-76 TDS, with Part Numbers (P/N) 76361-04004 (all dash 
numbers) with serial numbers prior to A127-01093, and 76361-04604 (all dash 
numbers) with serial number prefixes A240 (all serial numbers), B240 (all serial 
numbers), and C240 all serial numbers up to and including 00880. 
B. Purpose To perform a one-time inspection of TDS flange-to-shaft attachment hardware for 
proper installation and torque.  
There were instances where TDS flange-to-shaft attachment hardware has been 
found loose or fractured. 
C. Description Helicopter is prepared for maintenance. TDS is removed. TDS flange-to-shaft 
attachment hardware is inspected for movement, torque stripe misalignment, and 
correct assembly. If movement, misalignment of torque stripe, or misassembled 
hardware is found, TDS flange-to-shaft attachment hardware is removed, returned 
to Sikorsky along with attached Return for Sikorsky Engineering Evaluation form  
and Torque Verification of TDS Flange Bolt Data Sheet, and replaced with  
Sikorsky Aircraft Corporation 
6900 Main Street P.O. Box 9729 
Stratford, Connecticut 06615-9129 
(203) 386-4000 
 
Page 1 of 17 
 
ONE-TIME 
INSPECTION

### Page 2

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 1.    PLANNING lNFORMATION (Continued) 
serviceable TDS flange-to-shaft attachment hardware. Helicopter is returned to 
service. 
D. Compliance Compliance is essential. The instructions outlined herein shall be accomplished no 
later than November 30, 2014. 
E. Approval Inspection item. 
F. Manpower (Estimated) 
Task No. of Men No. of Hours Man-Hours* 
Remove Driveshaft 1 0.75 0.75 
Inspect TDS Flange Attachment 
Hardware. 
1 0.50 0.50 
Install Driveshaft 
(*Existing assembly or new if unit is found 
to be unserviceable). 
1 1.00 1.00 
Total Man-Hours   2.25 
*Estimate does not include time required to prepare helicopter or return it to flight status.  
 
 
G. Tooling 
Qty Nomenclature Part No. Source 
1 Locally Fabricated Special Tool Modified McMaster Carr P/N 
5543A35 or equivalent 
(1) 
1 Torque Wrench (30 - 150 inch-
pounds) 
Commercially Available or equivalent (2) 
1 Caliper Commercially Available or equivalent (2) 
    
 
(1) Available from McMaster Carr. Website: www.mcmaster.com  
(2) Procure through local supply. 
H. Weight and Balance 
Not affected. 
 
Page 2 
ONE-TIME 
INSPECTION

### Page 3

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 1.    PLANNING lNFORMATION (Continued) 
I. Electrical Load Data 
Not affected. 
J. Software Load Data 
Not changed. 
K. References 
(1) Maintenance Manual SA 4047-76-2, Chapter/Section 20-04-00. 
(2) Maintenance Manual SA 4047-76B-2, Chapter/Section 20-04-00. 
(3) Maintenance Manual SA 4047-76C-2, Chapter/Section 20-04-00. 
(4) Maintenance Manual SA S76D-AMM-000, Chapter/Section 20-04-00. 
(5) Maintenance Manual SA S76D-AMM-000, Chapter/Section 65-11-01. 
(6) Maintenance Manual SA S76D-AMM-000, Chapter/Section 65-11-02. 
(7) Maintenance Manual SA S76D-AMM-000, Chapter/Section 65-11-04. 
(8) Maintenance Manual SA S76D-AMM-000, Chapter/Section 65-13-02. 
(9) Maintenance Manual SA 4047-76-2, Chapter/Section 66-40-00. 
(10) Maintenance Manual SA 4047-76B-2, Chapter/Section 66-40-00. 
(11) Maintenance Manual SA 4047-76C-2, Chapter/Section 66-40-00. 
L. Publications Affected 
(1) Temporary Revision No. 66-28 against Maintenance Manual, SA 4047-76B-2, 
Chapter/Section 66-40-00 is issued concurrently with this ASB. 
(2) Temporary Revision No. 66-29 against Maintenance Manual, SA 4047-76C-2, 
Chapter/Section 66-40-00 is issued concurrently with this ASB. 
(3) Temporary Revision No. 66-52 against Maintenance Manual, SA 4047-76-2, 
Chapter/Section 66-40-00 is issued concurrently with this ASB. 
(4) Temporary Revision No. 65-02 against Maintenance Manual, SA S76D-AMM-000, 
Chapter/Section 65-13-02 is issued concurrently with this ASB. 
 
Page 3 
ONE-TIME 
INSPECTION

### Page 4

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 2. MATERIAL INFORMATION 
A. Attachment 
Return for Sikorsky Engineering Evaluation form. 
B. Basis for Material Data 
Per helicopter. 
C. Bill of Material 
None. 
C. Consumable Material 
 
Qty Nomenclature Part No. Source 
A/R Corrosion Preventive Compound MIL-C-81309 Type 2, 3 or equivalent (1) 
A/R Epoxy Polyamide Primer MIL-PRF-23377 or equivalent (1) 
 Epoxy Primer (Alternate) MIL-PRF-85582 or 
equivalent 
(1) 
    
 
(1) Procure through local supply. 
Section 3. ACCOMPLISHMENT INSTRUCTIONS 
A. Prepare helicopter for maintenance: 
(1) Turn off all helicopter electrical and hydraulic power. 
(2) Engage rotor brake. 
(3) Remove driveshaft from helicopter. (Refer to applicable Maintenance Manual). 
 
OBSERVE ALL CAUTIONS AND WARNINGS ON CONTAINERS 
WHEN USING CONSUMABLES. WHEN APPLICABLE, WEAR 
NECESSARY PROTECTIVE GEAR DURING HANDLING AND USE. IF 
A CONSUMABLE IS FLAMMABLE OR EXPLOSIVE, MAKE CERTAIN 
CONSUMABLE AND ITS VAPORS ARE KEPT AWAY FROM HEAT, 
SPARK AND FLAME. MAKE CERTAIN FIREFIGHTING EQUIPMENT 
IS READILY AVAILABLE PRIOR TO USE. FOR ADDITIONAL 
INFORMATION ON TOXICITY, FLASHPOINT AND FLAMMABILITY 
OF CHEMICALS, CONSULT YOUR MEDICAL PEOPLE OR THE 
MANUFACTURER OF THE CONSUMABLE. 
Page 4 
ONE-TIME 
INSPECTION

### Page 5

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3.  ACCOMPLISHMENT INSTRUCTIONS (Continued) 
B. Inspect TDS as follows: 
NOTE: This inspection must be performed for all TDS’s listed in effectivity section. 
(1) Inspect TDS flange attachment hardware at all four locations (four locations for each drive 
shaft) (Figures 1 and 2) for evidence of movement or torque stripe misalignment. If 
evidence of movement or torque stripe misalignment, proceed to Step D. 
(2) Attempt to rotate each nut (SS5086-04) using finger pressure. If hardware can be rotated 
by hand, proceed to Step D. 
(3) Check that hardware is assembled correctly as follows: 
(a) Verify that only one radius washer is present under the head of the bolt and oriented 
correctly, with the radius side adjacent to the inner diameter. (Refer to Figure 3). 
(b) Verify that one thick washer and one thin washer are present under the nut. (Refer 
to Figure 3). 
(c) If hardware is not assembled correctly, proceed to Step D. 
NOTE: If locally fabricated special tool (modified McMaster Carr, P/N 5543A35 or 
equivalent) is not available, proceed to Step B. (5). 
(4) Using locally fabricated special tool (modified McMaster Carr, P/N 5543A35 or equivalent) 
(Figure 4), check torque on each nut (SS5086-04) on TDS flange-to-shaft attachment. If 
torque on any nut is less than 105 inch-pounds, proceed to Step D. 
(5) If locally fabricated special tool (modified McMaster Carr, P/N 5543A35 or equivalent) is 
not available, perform torque verification check as follows: 
(a) Remove snap ring (S1635-61210), closest to flange, from bearing support assembly. 
(b) Slide bearing support assembly away from flange to allow clearance for common 
tools. (Figure 5). 
(c) Using torque wrench, check torque on each nut (SS5086-04) on tail rotor drive shaft 
flange-to-shaft attachment. If torque on any nut is less than 105 inch-pounds, 
proceed to Step D. 
 
 
 
Page 5 
ONE-TIME 
INSPECTION

### Page 6

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 3.  ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
(d) Reinstall snap ring (S1635-61210) to bearing support assembly. 
C. If during the inspection, no evidence of movement was found, torque stripe was not misaligned, 
hardware could not be rotated by hand, hardware was assembled correctly, or torque of any nut 
was not less than 105 inch-pounds, perform the following: 
(1) Re-apply torque stripe as required. (Refer to applicable Maintenance Manual, 
Chapter/Section 20-04-00).  Inspection is complete, proceed to Section 3, Step E. 
D. If during the inspection, evidence of movement was found, torque stripe was misaligned, 
hardware rotated by hand, hardware was not assembled correctly, or torque of any nut was less 
than 105 inch-pounds, perform the following: 
NOTE: • Index mark is applied to flange and shaft to make sure flange is reinstalled in the 
same position and to maintain shaft balance. 
• If applicable, record information in Torque Verification of TDS Flange Bolt Data 
Sheet. 
(1) Apply index mark to flange and shaft. 
NOTE: • With the exception of radius washers, all shaft to flange attaching hardware is 
one time use. After removal, return bolts, washers, and nuts to Sikorsky (address 
below) with attached Return for Sikorsky Engineering Evaluation form. 
• Radius washers (SS4411-08S025NP or ALT SS4411-08S025) may be reused if 
inspected and no visible signs of wear or fretting is found. If radius washers are 
damaged return to Sikorsky (address below) with attached Return for Sikorsky 
Engineering Evaluation form. 
(2) Unbolt and remove flange from shaft. 
(3) Visually inspect radius washers (SS4411-08S025NP or ALT SS4411-08S025) for wear or 
fretting. 
NOTE: • Include time since new (TSN) and time since overhaul (TSO) for returned 
hardware. 
• Radius washers (SS4411-08S025NP or ALT SS4411-08S025) are only to be 
returned if found damaged. 
 
 
Make sure snap ring is reseated in groove and locked. 
Failure to reseat snap ring in groove can cause unintended 
failure of drive shaft bearing. 
Page 6 
ONE-TIME 
INSPECTION

### Page 7

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(4) Return flange to shaft hardware (four sets: nuts, bolts, washers, and radius washers if 
necessary) to Sikorsky with attached Return for Sikorsky Engineering Evaluation form  and 
Torque Verification of TDS Flange Bolt Data Sheet at the address below: 
HELICOPTER SUPPORT INC. (H.S.I.) 
URGENT: Engineering Evaluation 
Attn: CSS Commercial Aircraft Product Support 
300 Monotowese Avenue Extension 
North Haven, CT 06473 
(5) Replace TDS with a serviceable unit, or inspect flange and stub as follows: 
(a) Inspect driveshaft and flange for cracks and fractures using fluorescent penetrant. 
No cracks or fractures allowed. (Refer to Figure 6, Reference Letters A and B). 
(b) Inspect wear of mounting hole on driveshaft and flange. Hole diameter shall be no 
greater that 0.252 inch maximum. Holes may be up to 0.0015 inch out-of-round if 
diameter is met. (Refer to Figure 6, Reference Letter C). 
(c) Using caliper (commercially available or equivalent), measure stub shaft outer 
diameter. Diameter shall be no less than 1.7565 inches minimum. (Refer to Figure 6, 
Reference Letter D). 
(d) Using caliper (commercially available or equivalent), measure flange inner diameter. 
Diameter shall be no more than 1.7585 inches. (Refer to Figure 6, Reference Letter 
E). 
(e) Using caliper (commercially available or equivalent), measure flange face width . 
(Refer to Figure 6, Reference Letter F): 
1. For driveshafts with P/N 76361-04004 (all dash numbers), width shall be no 
less than 0.210 inches minimum. 
2. For driveshafts with P/N 76361-04604 (all dash numbers), width shall be no 
less than 0.275 inches minimum. 
(f) If any parts fail any of the criteria listed here, the part is to be scrapped and replaced 
with a serviceable unit. 
(6) If necessary, replace bearing support as follows: 
(a) Remove bearing support from shaft. 
(b) If necessary, remove snap rings (S1635-61210) and press out bearing from support. 
(c) Coat Outer Diameter (OD) of new bearing and Inner Diameter (ID) of bearing liner 
with corrosion preventive compound (MIL-C-81309, Type 2, 3 or equivalent), and 
press bearing into support. Remove excess squeeze out. Install snap rings (S1635-
61210). 
Page 7 
ONE-TIME 
INSPECTION

### Page 8

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(d) Install bearing support assembly on shaft so that bearing inner race is over liner of 
shaft. 
(7) Align index marks and install flange on shaft. 
NOTE: • When installing flange on shaft for shaft assemblies 76361-04004 or 76361-
04604, use new bolts, washers, and nuts. 
• Radius washers (SS4411-08S025NP or ALT SS4411-08S025) may be reused if 
inspected and no damage is found. 
(8) Coat grip length of bolts, and contact surfaces on radius washers and washers with epoxy 
polyamide primer (MIL-PRF-23377 or equivalent). Do not prime threads of bolts. 
NOTE: Ensure that radius washer (SS4411-08S025NP or ALT SS4411-08S025) is 
properly seated against the inside diameter of the shaft. 
(9) If using locally fabricated special torque tool (modified McMaster Carr, P/N 5543A35 or 
equivalent) to install flange to shaft, perform the following (Refer to Figure 4): 
(a) Hand tighten attaching hardware in all locations. 
(b) Measure prevailing torque of nuts (SS5086-04) at every location and record value. 
Prevailing torque values should be between 3.5 - 30 inch-pounds. If prevailing 
torque value is above or below 3.5 - 30 inch-pounds, replace nut. 
 
(c) Torque nuts (SS5086-04) to 50 inch-pounds in the sequence shown in Figure 3. 
(d) Repeat torque sequence on nuts at 75 inch-pounds. 
(e) Repeat torque sequence on nuts at 110 inch-pounds plus measured prevailing 
torque for each location and until torque has stabilized for each location. 
(10) If locally fabricated special torque tool (modified McMaster Carr, P/N 5543A35 or 
equivalent) is unavailable, perform the following: 
(a) Remove snap ring (S1635-61210), closest to flange, from bearing support assembly. 
(b) Slide bearing support assembly away from flange to allow clearance for common 
tools. (Figure 5). 
(c) Hand tighten attaching hardware in all locations. 
 
THE NUT (SS5086-04) IS TO BE TORQUED WHILE THE BOLT IS 
HELD STATIONARY. 
Page 8 
ONE-TIME 
INSPECTION

### Page 9

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(d) Measure prevailing torque of nuts (SS5086-04) at every location and record value. 
Prevailing torque values should be between 3.5 - 30 inch-pounds. If prevailing 
torque value is above or below 3.5 - 30 inch-pounds, replace nut. 
 
(e) Torque nuts (SS5086-04) to 50 inch-pounds in the sequence shown in Figure 3. 
(f) Repeat torque sequence on nuts at 75 inch-pounds. 
(g) Repeat torque sequence on nuts at 110 inch-pounds plus measured prevailing 
torque for each location and until torque has stabilized for each location. 
(h) Reinstall snap ring (S1635-61210) to bearing support assembly. 
(11) Apply torque stripe, to nuts, washers, and bolt ends. (Refer to applicable Maintenance 
Manual, Chapter/Section 20-04-00).  
(12) Service TDS assembly. (Refer to applicable Maintenance Manual). 
(13) Reinstall TDS assembly. (Refer to applicable Maintenance Manual). 
E. Perform inspection on all TDS assemblies listed in Effectivity section.  
F. Return helicopter to service. 
 
THE NUT (SS5086-04) IS TO BE TORQUED WHILE THE BOLT IS 
HELD STATIONARY. 
Page 9 
ONE-TIME 
INSPECTION

### Page 10

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
G. Torque Verification of TDS Flange Bolt Data Sheet. 
(1) Report the following data back to Sikorsky Aircraft Design Engineering Point of Contact. 
(Refer to Section 3, Step D. (4)). 
(2) Record the following information for each helicopter: 
 
Customer/Operator Name:    
 
Helicopter Serial Number:    
 
Helicopter Total Time Since New:    
 
Time Since Last Overhaul:    
 
Flange Location Between Driveshaft Sections I and II:   
 
Driveshaft Serial Number:   
 
Last Hardware Replacement Date (if known):    
 
Number of Flange Bolts that Passed/Failed Torque Check: Passed Failed    
 
Flange Location Between Driveshaft Sections II and III:   
 
Driveshaft Serial Number:   
 
Last Hardware Replacement Date (if known):    
 
Number of Flange Bolts that Passed/Failed Torque Check: Passed Failed    
 
Flange Location Between Driveshaft Sections III and IV:   
 
Driveshaft Serial Number:   
 
Last Hardware Replacement Date (if known):    
 
Number of Flange Bolts that Passed/Failed Torque Check: Passed Failed    
 
Date Inspection is Performed:   
 
 
 
 
 
 
 
 
 
Page 10 
ONE-TIME 
INSPECTION

### Page 11

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
TDS FLANGE-TO-SHAFT HARDWARE INSTALLATION 
FIGURE 1 
Page 11 
ONE-TIME 
INSPECTION

### Page 12

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
TORQUE STRIPE VERIFICATION 
FIGURE 2 
 
 
 
 
 
 
 
 
 
 
 
Page 12 
ONE-TIME 
INSPECTION

### Page 13

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
HARDWARE STACK-UP AND TORQUE PATTERN 
FIGURE 3 
 
 
 
 
 
 
 
 
 
Page 13 
ONE-TIME 
INSPECTION

### Page 14 (OCR)

S-76 ALERT  ASB 76-66-52
SERVICE BULLETIN  Basic Issue • April 1/14
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
/4 (0.250) INCH DRIVE x 7/16 (0.437  0.425
NCHES 12 POINT SOCKET (MCMASTEF
P / N 5543A35 OR EQUIVALENT)
0.300 MIN -→
1.130
0.120 × 4:
SECTION A-A
TD3179
LOCALLY FABRICATED SPECIAL TOOL (MCMASTER P/N 5543A35)
FIGURE 4
ONE-TIME
Page 14  INSPECTION

### Page 15

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
 
BEARING SUPPORT ASSEMBLY 
FIGURE 5 
 
 
 
 
 
 
 
 
 
 
Page 15 
ONE-TIME 
INSPECTION

### Page 16

S-76 ALERT ASB 76-66-52 
SERVICE BULLETIN Basic Issue ▪ April 1/14 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
DRIVESHAFT INSPECTION 
FIGURE 6     
 
 
 
 
 
 
 
 
 
 
Page 16 
ONE-TIME 
INSPECTION

### Page 17

ASB 76-66-52 S-76 ALERT 
Basic Issue ▪ April 1/14 SERVICE BULLETIN 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
            H. Record of Compliance: 
(1) Make helicopter logbook entries to show compliance with this ASB as follows: 
(a) Make helicopter level logbook entry on form SA7343-15. 
(b) When ASB modifies a component that can be removed from this helicopter: 
1. Make component log card entries on forms SA7343-22 & SA7343-21 as 
applicable. 
2. If a component modified by this ASB does not have a log card and the ASB 
does not create one, then annotate compliance on the next higher assembly 
that the component belongs to which does have a log card. 
NOTE: If access to www.Sikorsky360.com is unavailable, complete attached ALERT 
SERVICE BULLETIN COMPLIANCE RECORD CARD and return it to Sikorsky 
Aircraft Corporation. 
(2) Make an appropriate electronic compliance entry in the E-Notification section at 
www.Sikorsky360.com. Refer to User Guide located on the www.Sikorsky360.com/E-
Notification Search page. 
 
 
 
Page 17 
ONE-TIME 
INSPECTION

### Page 18

(Fold over and tape closed) 
SIKORSKY AIRCRAFT CORPORATION 
FACSIMILE NUMBER (860) 998-7565 
EMAIL ADDRESS: GPSIKSASProductSafet@utc.com 
ATTENTION: SAS PRODUCT SAFETY MANAGER 
SIKORSKY AEROSPACE SERVICES 
 
(Fold Up to Arrows) 
IMPORTANT NOTICE 
Upon COMPLIANCE with the attached ASB, Sikorsky requests your cooperation 
in completing and returning this ENTIRE PAGE by MAIL, FAX, or scan & 
EMAIL. 
Please fill in the requested information at the bottom of the page, so we may maintain 
proper records documenting the configuration of your aircraft. This information is useful 
when determining configuration and effectivity of issues affecting fielded aircraft. 
This request is in keeping with our policy to assure that our customers receive the latest 
information applicable for the maintenance of your aircraft. Thank you. 
ALERT SERVICE BULLETIN:  ________________  Compliance Record Card 
TITLE:  ___________________________________________________________________  
  ___________________________________________________________________  
  ___________________________________________________________________  
OWNER/OPERATOR:  _____________________________________________________  
SUBMITTED BY:  ___________________________  DATE:  ____________________  
FOLLOWING SERIAL NUMBERS ARE NOT AFFECTED BY THIS ASB 
ASB HAS BEEN COMPLIED WITH ON HELICOPTER SERIAL NUMBERS: 
 ___________   ___________   ___________   ___________   ___________   ___________  
 ___________   ___________   ___________   ___________   ___________   ___________  
                  
ASB No. 76-66-52 
POWERTRAIN – Tail Drive Shaft – One-Time Inspection and Torque Verification 
of Tail Drive Shaft (TDS) Flange Bolt

### Page 19

No Postage 
Necessary 
BUSINESS REPLY MAIL 
FIRST-CLASS MAIL PERMIT NO. 432 BRIDGEPORT CT 
POSTAGE WILL BE PAID BY ADDRESSEE 
SIKORSKY AIRCRAFT CORPORATION 
P.O. BOX 9729 
6900 MAIN STREET 
STRATFORD, CONNECTICUT 06615-9129 U.S.A. 
MAILSTOP: S328A 
ATTENTION: SAS PRODUCT SAFETY MANAGER 
 SIKORSKY AEROSPACE SERVICES 
Please complete the form on the reverse side and FAX to 
FACSIMILE NUMBER (860) 998-7565 
Or scan and email to: 
EMAIL ADDRESS: GPSIKSASProductSafet@utc.com 
or fold and return ENTIRE form to Sikorsky Aircraft Corporation

### Page 20

Return for Sikorsky Engineering Evaluation  
RETURN INSTRUCTIONS: 
  
Return parts indicated below to Sikorsky Aircraft Corporation by the fastest traceable means with the 
following information:  
  
Send to:  
     Helicopter Support, Inc. (H.S.I.)     
     URGENT: Engineering Evaluation 
  Attn: CSS Commercial Aircraft Product Support 
300 Montowese Avenue Extension 
North Haven, CT 06473   
 
 
Mark for:   S-61   S-70   S-76      S-92 
 
 
 Product Safety/Engineering Evaluation     
 
    Engineering   
      
 HUMS Anomaly or Exceedance         
      
 PART INFORMATION:  
 
Part Number                  _________                    Serial Number: ____________ 
Nomenclature           ____________________________________________________________  
Reason for Removal Failed torque inspection per ASB 76-66-55 
 
Helicopter Serial Number __________          A/C Hours at Removal:   ________     
Date Removed:  ________                Component Hours at Removal:   ________  
TSR:  ________                             TSO:   ________  
Customer/Operator Name _______________________________________________________  
Sikorsky FTR # _______________ 
Sikorsky RFA # _______________ 
Requested by customer or Sikorsky? Sikorsky per ASB 76-66-52 TRD Hardware Check 
 (if Sikorsky, please list requestor name) 
  
 Remarks: Notify Tim Tomasko upon part arrival and send to the materials lab 
 
 ADDITIONAL INSTRUCTIONS:  
  
1. Fax or email a copy of this form with shipping information (AWB#, Flight#, Shipper Tracking#)  
as applicable to +1 860-353-6557 or sascommercialproduct@utc.com   
Include a copy of this form in the box with the part.  
 
2. If a Sikorsky FSR is on-site, obtain the FTR # from him and record in the spaces above, if not already 
annotated.  
 
3. Any questions regarding the return of this part should be directed to the Requestor listed above.  
SA 1600 5/4/11 
  Verify current revision of form

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
