# Sikorsky Alert Service Bulletin 92-62-010

Copy: No revision named ("Sikorsky ASB 92-62-010"), 17 pages: PDF https://openairdocs.org/files/sha256/eb/38/eb380495ac0f65bd26eb4c313720c673794480ad437f4436621bf2b8d08216f3; text https://openairdocs.org/service-documents/sikorsky/sb-92-62-010/file/eb380495ac0f.md. Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2023-0018, the docket of AD 2023-09-07. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Sikorsky](https://openairdocs.org/service-documents/sikorsky.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 92-62-010
- Page: https://openairdocs.org/service-documents/sikorsky/sb-92-62-010

## Text (17 pages)

Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2023-0018, the docket of AD 2023-09-07. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 of 15 
ATA
62-31-01
ONE-TIME 
INSPECTION 
S-92® HELICOPTER 
ALERT SERVICE  
BULLETIN 
NOTICE TO ALL PERSONS RECEIVING THIS DOCUMENT: 
WARNING: THIS DOCUMENT, OR AN EMBODIMENT OF IT IN ANY MEDIA, DISCLOSES INFORMATION WHICH IS PROPRIETARY, IS THE PROPERTY OF LOCKHEED MARTIN CORPORATION AND/OR ITS SUBSIDIARIES, IS 
AN UNPUBLISHED WORK PROTECTED UNDER APPLICABLE COPYRIGHT LAWS, AND IS DELIVERED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED, DISCLOSED, REPRODUCED, IN WHOLE OR IN PART 
(INCLUDING REPRODUCTION AS A DERIVATIVE WORK), OR USED FOR MANUFACTURE FOR ANYONE OTHER THAN LOCKHEED MARTIN CORPORATION AND/OR ITS SUBSIDIARIES WITHOUT ITS WRITTEN CONSENT,
AND THAT NO RIGHT IS GRANTED TO DISCLOSE OR SO USE ANY INFORMATION CONTAINED HEREIN. ALL RIGHTS RESERVED. ANY ACT IN VIOLATION OF APPLICABLE LAW MAY RESULT IN CIVIL AND CRIMINAL 
PENALTIES. 
S-92® IS A REGISTERED TRADEMARK OF SIKORSKY AIRCRAFT CORPORATION. 
ASB 92-62-010 
Basic Issue ▪ January 26/22 
SUBJECT: ROTORS – Main Rotor (MR) Swashplate Assembly – One-Time Inspection of MR Stationary 
Swashplate Assembly to Initiate a 50-Hour Recurring Inspection 
Section 1. PLANNING INFORMATION 
A. Effectivity All S-92A helicopters with Serial Numbers (S/Ns) 920006 through subsequent 
equipped with MR stationary swashplate assemblies (92104-15011-042/-043) 
including spares, delivered as of the issue date of this Alert Service Bulletin (ASB). 
B. Purpose To provide instructions for a one-time inspection of MR stationary swashplate 
assembly (92104-15011-042/-043) for cracks. Also, to initiate a 50-hour recurring 
inspection. 
C. Background An occurrence of an in-service crack was reported on MR stationary swashplate 
assembly inner ring during a recurring inspection. A detailed inspection has been 
developed to determine if cracks are present. 
D. Description Helicopter is prepared for inspection. Visual inspection of MR stationary 
swashplate assembly is performed. Dependent on accrued flight time or suspicion 
of cracks, a Fluorescent Penetrant Inspection (FPI) or Eddy Current (EC) 
inspection is performed. If cracks are confirmed, swashplate assembly is removed, 
replaced, and Sikorsky Customer Service Engineering is contacted. Helicopter is 
returned to service. 
Sikorsky Aircraft Corporation
6900 Main Street P.O. Box 9729 
Stratford, Connecticut 06615-9129 
(203) 386-4000
WARNING – This document/file contains export controlled information subject to the EAR. ECCN EAR99

### Page 2

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 2 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 1. PLANNING lNFORMATION (Continued) 
E. Compliance Compliance is essential. The inspection outlined herein shall be accomplished 
within 100 flight hours or 30 days from the issue date of this ASB, whichever 
occurs first. 
F. Approval Inspection Item. 
G. Manpower (Estimated) 
Task No. of Men No. of Hours Man-Hours* 
Visual Inspection of MR Stationary 
Swashplate Assembly 
1 1.0 1.0 
Performance of Fluorescent Penetrant 
Inspection (FPI) or Eddy Current (EC) 
1 8.0 8.0 
Total Man-Hours 9.0 
*Estimate does not include time required to prepare helicopter or return it to flight status. 
H. Tooling 
Qty Nomenclature Part No. Source 
1 Nonmetallic Scraper Commercially available or equivalent (1) 
A/R Inspection Mirror Commercially available or equivalent (1) 
A/R Magnaflux EV6000 Commercially available or equivalent (1) 
A/R Olympus NORTEC 600 Commercially available or equivalent (1) 
A/R Probe, straight, shielded surface, 
100 kHz-500 kHz 
Commercially available or equivalent (1) 
A/R Manual bolt hole inspection 
probe, shielded 
(1) 
A/R Manual bolt hole inspection 
probe, shielded, 50 kHz-500 kHz  
Commercially available or equivalent (1) 
A/R Cable assembly Commercially available or equivalent (1) 
A/R Reference block, three-notched 
aluminum (0.008, 0.020, 0.040 
EDM notches) or hole standard 
for use with bolt hole probes 
Commercially available or equivalent (1) 
This document/file contains export controlled information. See WARNING on first page.

### Page 3

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 3 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 1. PLANNING lNFORMATION (Continued) 
(1) Available through normal supply channels. 
I. Weight and Balance 
Not affected. 
J. Electrical Load Data 
Not affected. 
K. Software Load Data 
Not changed. 
L. References 
(1) Maintenance Manual SA S92A-AMM-000, Task 20-06-00-910-005. 
(2) Maintenance Manual SA S92A-AMM-000, Task 20-06-00-910-007. 
(3) Maintenance Manual SA S92A-AMM-000, Tasks 62-31-01-900-001/-002. 
(4) Maintenance Manual SA S92A-AMM-000, Tasks 62-20-00-219-001. 
(5) Structural Repair Manual, SA S92A-SRM-000, Task 20-10-00-390-007. 
(6) Structural Repair Manual, SA S92A-SRM-000, Task 62-20-01-300-005 
M. Publications Affected 
(1) Temporary Revision 62-43 against Maintenance Manual, SA S92A-AMM-000, Task 62-31-
00-215-001 will be released concurrently with this ASB. 
(2) Temporary Revision 62-44 against Maintenance Manual, SA S92A-AMM-000, Task 62-31-
01-210-001 will be released concurrently with this ASB. 
(3) Temporary Revision 62-45 against Maintenance Manual, SA S92A-AMM-000, Task 62-20-
00-219-001 will be released concurrently with this ASB. 
(4) Temporary Revision 62-46 against Maintenance Manual, SA S92A-AMM-000, Task 62-31-
01-900-001 will be released concurrently with this ASB. 
(5) Temporary Revision 62-47 against Maintenance Manual, SA S92A-AMM-000, Task 62-31-
02-900-001 will be released concurrently with this ASB. 
(6) Temporary Revision 62-48 against Maintenance Manual, SA S92A-AMM-000, Task 62-31-
03-900-001 will be released concurrently with this ASB. 
(7) Temporary Revision 67-26 against Maintenance Manual, SA S92A-AMM-000, Task 67-31-
01-900-001will be released concurrently with this ASB. 
This document/file contains export controlled information. See WARNING on first page.

### Page 4

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 4 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 1. PLANNING lNFORMATION (Continued) 
N. Attachment 
None. 
Section 2. MATERIAL INFORMATION 
A. Procurement Requirements: 
None. 
B. Basis for Material Data 
Per helicopter. 
C. Bill of Material 
None. 
D. Consumable Material 
Qty Nomenclature Part No. Source 
A/R Low-lint Cloth A-A-59323 or equivalent (1) 
A/R Brulin Cleaner SD 1291 or equivalent (1) 
A/R Paint Stripper MIL-R-81294 or equivalent (1) 
A/R Teflon tape Commercially available or equivalent (1) 
A/R Aircraft marking pencil Commercially available or equivalent (1) 
A/R Level 3 Solvent Removable 
Fluorescent Penetrant 
ZL-67A or equivalent (1) 
A/R Non-Aqueous, Developer ZP-9F or equivalent (1) 
(1) Available through normal supply channels. 
OBSERVE ALL CAUTIONS AND WARNINGS ON CONTAINERS 
WHEN USING CONSUMABLES. WHEN APPLICABLE, WEAR 
NECESSARY PROTECTIVE GEAR DURING HANDLING AND USE. IF 
A CONSUMABLE IS FLAMMABLE OR EXPLOSIVE, MAKE CERTAIN 
CONSUMABLE AND ITS VAPORS ARE KEPT AWAY FROM HEAT, 
SPARK AND FLAME. MAKE CERTAIN FIREFIGHTING EQUIPMENT 
IS READILY AVAILABLE PRIOR TO USE. FOR ADDITIONAL 
INFORMATION ON TOXICITY, FLASHPOINT AND FLAMMABILITY 
OF CHEMICALS, CONSULT YOUR MEDICAL DEPARTMENT OR 
THE MANUFACTURER OF THE CONSUMABLE. 
This document/file contains export controlled information. See WARNING on first page.

### Page 5

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 5 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS 
A. Prepare helicopter for inspection: 
(1) Turn off all helicopter electrical and hydraulic power. 
(2) Engage rotor brake. 
(3) Helicopters operating at a gross weight of 26,500 lbs. equipped with swashplate assembly 
with less than 8,600 flight hours, or helicopters operating at a gross weight of 27,700 lbs., 
equipped with swashplate assembly with less than 3,300 flight hours, shall perform the 
visual inspection per step B. 
(4) Helicopters operating at a gross weight of 26,500 lbs. equipped with swashplate assembly 
with 8,600 flight hours or above, or helicopters operating at a gross weight of 27,700 lbs., 
equipped with swashplate assembly with 3,300 flight hours or above, shall perform the 
visual inspection per step B. as well as the eddy current inspection per step C. or 
Fluorescent Penetrant Inspection (FPI) per step D. 
NOTE: Removal of components are not required for visual inspection of the swashplate 
assembly (92104-15011-042/-043). 
B. Inspect swashplate assembly (92104-15011-042/-043) as follows: 
(1) Using clean, low-lint cloth and Brulin cleaner (SB 1291), remove all traces of oil and dirt 
from the following locations: 
 Stationary swashplate: Uniball lower bore lip. (Refer to Figure 1). 
 Stationary swashplate: Uniball upper bore. (Refer to Figure 2). 
 Stationary swashplate: Trunnion mount bolt holes. (Refer to Figure 3). 
NOTE: The presence of sealing compound around holes should be minimal. 
(2) If sealing compound at trunnion attachment bolts is obstructing view of the trunnion mount 
area, remove sealing compound from nuts using non-metallic scraper. Clean area with low-
lint cloth moistened with Brulin cleaner (SD 1291). 
NOTE: The area under caulking, wire harnesses, wire harness mounts, brackets, washers, 
and bolts shall be omitted from inspection zones. 
(3) Using strong white light, and inspection mirror, visually inspect the following defined zones 
for cracks or other anomalies: No cracks allowed. 
NOTE: Crack may start at the bearing race interface lip and propagate outward 
breaking through bottom surface. 
TO PREVENT ELECTRICAL SHOCK OF PERSONNEL OR 
POSSIBLE DAMAGE TO HELICOPTER COMPONENTS, MAKE 
SURE TO TURN OFF ALL ELECTRICAL POWER. 
This document/file contains export controlled information. See WARNING on first page.

### Page 6

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 6 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(a) Uniball lower bore lip – Search for cracks emanating from underside of inner ring. 
See Figure 1, Detail B. 
NOTE: Crack may start at upper end of inner bore and propagate outward. 
(b) Uniball upper bore – Breakthrough occurs on vertical wall near bearing retainer. See 
Figure 2, Details A and B.  
NOTE: Cracks in the swashplate may start at the trunnion attachment under the hole 
bushing flange and propagate radially outward. 
(c) Trunnion mount bolt holes – Inspection zone begins outside of the minimal caulking 
region. See Figure 3, Detail A. 
(4) During visual inspection, discontinuities in the surface may be observed that require 
confirmation as either (1) a detectable crack (none allowed) that would have a detectable 
depth or length, or (2) only a surface break defect (suspected crack) in the paint/primer that 
could include observable metallic base material. The process steps to confirm a detectable 
crack is to perform either the FPI (step D) or eddy current inspection (step C). 
(5) If a crack is suspected at underside of swashplate assembly trunnion mount bolt holes, 
remove trunnion to perform FPI/ eddy current inspection. (Refer to Maintenance Manual 
SA S92A-AMM-000, Task 62-31-03-900-001). 
(6) If presence of crack is confirmed, contact Sikorsky Customer Service Engineering at 1-
800-WINGED-S or Email; wcs_cust_service_eng.gr-sik@lmco.com. Remove main rotor 
swashplate assembly (92104-15011-042/-043) and trunnions and return to Sikorsky 
Aircraft. (Refer to Maintenance Manual SA S92A-AMM-000, Task 62-31-01-900-001). 
(7) If no cracks are found, proceed to step E. 
NOTE:  •    FPI or Eddy Current inspection is to be performed only if crack in swashplate 
(92104-15011-042/-043) is suspected. 
 The following eddy current inspection procedure may be used where no specific 
inspection procedure exists for surface or manual hole inspection of aluminum 
alloys. 
 This procedure establishes the minimum requirements and procedure Eddy Current 
method of structures called out by Engineering Drawing and/or Specification for 
eddy current surface inspection for crack detection. 
 This process specification provides the minimum controls and requirements for 
accomplishing eddy current inspection of components and also establishes the 
general requirements for personnel, equipment, and application procedures so that 
the inspection practices employed are conducted in a safe, nondestructive, and 
reliable manner. 
This document/file contains export controlled information. See WARNING on first page.

### Page 7

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 7 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 A partial inspection for cause (visual indications, sites of mechanical damage, 
corrosion, etc.) may be performed on all exposed surfaces of the swashplate 
assembly using this procedure. 
C. If performing Eddy Current Inspection, do the following: 
(1) Visually confirm start and stop locations of suspected crack. 
(2) Make the following initial settings on the Eddy Current Inspection Unit: 
Table 1
MAIN MENU FILTER MENU DISPLAY MENIU
FREQ 200 KHz LP Filter 100 H Pos 80 Percent 
ANG 56 degrees HP Filter Off V Pos 20 Percent 
H Gain 57 db 
V Gain 69 db 
Probe Drive Mid 
NOTE:  •    Probe adapters may be used to aid in ensuring reliable and repeatable 
inspections. 
 Bolt hole probes shall match as closely as possible (without exceeding) bolt 
hole diameter. Split core probes may be expanded based on the limits of the 
manufacturer’s recommendations. This size of the probe shall ensure light 
continuous contact with the holes interior surface. 
(3) Place probe on block in area without a notch and null the instrument: 
(a) Hold probe coil on block parallel to surface or reference block.  
(b) Lift probe away from surface. Repeat as necessary. Note direction of lift off. (Refer 
to Figure 4). 
(4) Adjust Angle controls to rotate lift-off signal until displayed horizontally to the left on screen. 
NOTE:  •    Separation can be optimized by adjusting the H Gain, V Gain, and Angle 
controls. 
 Low Pass Filter (LPF) may be adjusted +100/-50 Hz to minimize noise while 
maintaining maximum signal amplitude. Noise shall not exceed 1/3 of the EDM 
notch response. 
(5) Move probe over all three notches in the test block. Adjust gain to obtain a five-block 
vertical signal when probe is passed over the 0.040-inch notch in the test block (See the 
standard instrument display in figure 4). Separation shall be distinguishable between all 
notches. 
(a) During each calibration check, verify that the instrument signal amplitude is within 
±10 percent of the initial reference notch signal amplitude. 
This document/file contains export controlled information. See WARNING on first page.

### Page 8

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 8 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(b) If these conditions are not met, recalibrate and reexamine all hardware inspected 
since the last successful system calibration verification. 
(c) Depth of defect can be estimated based on the phase separation of the known 
reference standard notch sizes.  
NOTE:   •    When the direction of principal loading is specified, scanning shall be 
parallel to the direction of loading. 
 When the direction of suspected cracking is known, scanning shall be 
perpendicular to the cracking direction. 
 When neither the principal loading direction nor cracking direction is 
known, scanning shall be in three directions, zero degrees, 45 degrees, 
and 90 degrees. For hole inspections using manual bolt hole probes, 
use overlapping scans in the circumferential direction. 
(d) Using the same system setting, operating parameters, and scanning speed 
established during calibration, inspect area(s) specified in work order/drawing to 
ensure complete coverage of areas designated for inspection and scans should 
overlap scanning passes. Record results on applicable documents/forms.  
1. All relevant crack or cracklike indications with amplitudes equal to or greater 
than 50% of reference level signal (0.040-inch notch unless otherwise 
specified) shall be rejected and documented. 
NOTE: Area under caulking, wire harnesses, wire harness mounts, brackets, washers, and 
bolts shall be omitted from inspection zones. 
(6) Perform Eddy Current Inspection per Maintenance Manual, SA S92A-AMM-000, Task 20-
06-00-910-007, with primary focus on the following locations: No cracks allowed. 
NOTE: Cracks may start at the bearing race interface lip and propagate outward 
breaking through bottom surface. 
(a) Uniball lower bore lip – Search for cracks emanating from underside of inner ring. 
See Figure 1, Detail B. 
NOTE: Cracks may start at upper end of inner bore and propagate outward. 
(b) Uniball upper bore – Breakthrough occurs on vertical wall near bearing retainer. See 
Figure 2, Details A and B.  
NOTE: •  Cracks in the swashplate may start at the trunnion attachment under the 
hole bushing flange and propagate radially outward. 
 For eddy current inspection, offset tool can be used if probe is non-
shielded. For shielded probes, no offset tool is required. 
This document/file contains export controlled information. See WARNING on first page.

### Page 9

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 9 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(c) Trunnion mount bolt holes – Inspection zone begins outside of the minimal caulking 
region. See Figure 3, Detail A. 
1. If presence of crack is confirmed, contact Sikorsky Customer Service 
Engineering at 1-800-WINGED-S or Email; wcs_cust_service_eng.gr-
sik@lmco.com. Remove and return main rotor swashplate assembly (92104-
15011-042/-043), uniball assembly, trunnions, and all associated attachment 
hardware and shims to Sikorsky Aircraft. (Refer to Maintenance Manual SA 
S92A-AMM-000, Task 62-31-01-900-001). 
2. If no cracks are found, restore primer and topcoat as necessary per Structural 
Repair Manual, SA S92A-SRM-000, Task 62-20-01-300-005, and proceed to 
step E. 
(7) Record results on applicable documents/forms. 
D. If performing FPI, do the following: 
(1) Visually confirm start and stop locations of suspected crack. 
(2) Remove paint and remaining sealant material from suspected swashplate (92104-15011-
042/-043) inspection areas using paint stripper (MIL-R-81294) and non-metallic scraper. 
(Refer to Structural Repair Manual, SA S92A-SRM-000, Task 20-10-00-390-007). 
NOTE:   •  Inspection areas include swashplate uniball lower bore lip, swashplate upper 
bore, and swashplate trunnion mount bolts holes. 
 Area under caulking, wire harnesses, wire harness mounts, brackets, 
washers, and bolts shall be omitted from inspection zones. 
 Allow penetrant dwell time 20 minutes to 2 hours. 
 Penetrant (ZL-67A), from factory sealed pressurized can, shall be sprayed 
onto cotton tipped applicator to apply penetrant to part. 
 Allow developer dwell time 10 minutes to 1 hour. 
 Minimum intensity of blacklight (Magnaflux EV6000) shall be 1500 µw/cm 2 at 
part surface. 
(3) Using level 3 solvent removable fluorescent penetrant (ZL-67A) at sensitivity level 3, 
Perform FPI on the following defined zones. (Refer to Maintenance Manual SA S92A-
AMM-000, Task 20-06-00-910-005): 
NOTE:  Cracks may start at the bearing race interface lip and propagate outward 
breaking through bottom surface. 
(a) Uniball lower bore lip – Search for cracks emanating from underside of inner ring. 
See Figure 1, Detail B. 
This document/file contains export controlled information. See WARNING on first page.

### Page 10

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 10 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
NOTE: Cracks may start at upper end of inner bore and propagate outward. 
(b) Uniball upper bore – Breakthrough occurs on vertical wall near bearing retainer. See 
Figure 2, Details A and B. 
NOTE: Cracks in the swashplate may start at the trunnion attachment under the hole 
bushing flange and propagate radially outward. 
(c) Trunnion mount bolt holes – Inspection zone begins outside of the minimal caulking 
region. See Figure 3, Detail A. 
1. If there is excessive background fluorescence, remove anodized coating per 
Maintenance Manual SA S92A-AMM-000, Task 20-06-00-910-005. 
2. Minimum detectable flaw size shall be 0.125 inches. 
NOTE:  •     All linear crack indications shall be rejected. 
 Thru-wall linear crack indications, regardless of size, shall be rejected. Back-
to-back discontinuities may be through wall indications that shall require further 
investigation. 
(4) If presence of crack is confirmed, contact Sikorsky Customer Service Engineering at 1-
800-WINGED-S or Email; wcs_cust_service_eng.gr-sik@lmco.com. Remove main rotor 
swashplate assembly (92104-15011-042/-043) and trunnions (92104-15050-042) and 
return to Sikorsky Aircraft. (Refer to Maintenance Manual SA S92A-AMM-000, Task 62-31-
01-900-001). 
(5) If no cracks are found, restore primer and topcoat as necessary per Structural Repair 
Manual, SA S92A-SRM-000, Task 62-20-01-300-005, and proceed to next step. 
E. Inspect for any remaining FOD. Clean as required to remove any remaining FOD. 
F. Maintain 50-hour Inspection of the Stationary and Rotary Swashplate in accordance with 
Temporary Revision No. 62-43 against SA S92A-AMM-000, Task 62-31-00-215-001, listed in the 
Publications Affected section of this ASB. 
G. Return helicopter to service. 
MAKE SURE ALL FOREIGN OBJECT DEBRIS (FOD) IS REMOVED 
BEFORE RETURNING HELICOPTER TO SERVICE.
This document/file contains export controlled information. See WARNING on first page.

### Page 11

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 11 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
STATIONARY SWASHPLATE ASSEMBLY INSPECTION ZONES – UNIBALL LOWER BORE LIP 
FIGURE 1 
TD5088
SA
SECTION THROUGH RH TRUNNION ATTCH
SEE NOTE
    DENOTES CRACK INITIATION. YELLOW ARROW
DENOTES WHERE CRACK IS FIRST VISIBLE.  BLUE
ARROWS SHOW CRACK RADIATING FROM POINT
OF INITIATION.
X
X
NOTE
DETAIL ADETAIL A
DETAIL B
INSPECTION ZONE
EXAMPLE OF UNIBALL LOWER BORE LIP CRACK
This document/file contains export controlled information. See WARNING on first page.

### Page 12

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 12 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
STATIONARY SWASHPLATE ASSEMBLY INSPECTION ZONES – UNIBALL UPPER BORE  
FIGURE 2 
TD5089
SA
INSPECTION ZONE
    DENOTES CRACK INITIATION.  ARROWS SHOW CRACK
RADIATION FROM POINT OF INITIATION.
YELLOW ARROW DENOTES WHERE CRACK FIRST VISIBLE
UNDER RETAINER.  BLUE ARROWS DENOTES TYPICAL CRACK PATH.
X
NOTES
DETAIL B
1.
2.
EXAMPLE OF UPPER BORE CRACK
X
SECTION THROUGH RH TRUNNION ATTCH
SEE NOTE 1
DETAIL A
SEE NOTE 2
ZONE OUT TO TANGENCY OF RIB RADIUS
ZONE 0.6 IN. DOWN
FROM RETAINER
This document/file contains export controlled information. See WARNING on first page.

### Page 13

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 13 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
STATIONARY SWASHPLATE ASSEMBLY INSPECTION ZONE – TRUNNION MOUNT BOLT 
HOLES  
FIGURE 3 
TD5090
SA
Example ofTrunnion Mount Bolt HoleCrack
INSPECTION ZONE
EXAMPLE OF TRUNNION MOUNT BOLT HOLE CRACK
ZONE = 1.5 INCHES RADIALLY. AT
BOLT HEAD AND NUT SIDE OF
SWASHPLATE.
INSPECTION ZONE
EXAMPLE OF TRUNNION MOUNT BOLT HOLE CRACK
ZONE = 1.5 INCHES RADIALLY. AT
BOLT HEAD AND NUT SIDE OF
SWASHPLATE.
INSPECTION ZONE
EXAMPLE OF TRUNNION MOUNT BOLT HOLE CRACK
ZONE = 1.5 INCHES RADIALLY. AT
BOLT HEAD AND NUT SIDE OF
SWASHPLATE.
INSPECTION ZONE
EXAMPLE OF TRUNNION MOUNT BOLT HOLE CRACK
ZONE = 1.5 INCHES RADIALLY. AT
BOLT HEAD AND NUT SIDE OF
SWASHPLATE.
YELLOW ARROWS DENOTES CRACK
EMANATING FROM CENTER OF MOUNT
HOLES.  CRACK TYPICALLY INITIATES
UNDER BUSHING FLANGE.
NOTE
DETAIL B
VIEW FROM BELOW (NUT SIDE)
DETAIL A
View From Above
SEE NOTE
This document/file contains export controlled information. See WARNING on first page.

### Page 14

S-92 ALERT ASB 92-62-010 
SERVICE BULLETIN Basic Issue ▪ January 26/22 
Page 14 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
EDM NOTCHES  
FIGURE 4 
EDM NOTCHES
TD5094
SA
0.008 INCH
0.020 INCH
LIFT OFF
0.040 INCH
This document/file contains export controlled information. See WARNING on first page.

### Page 15

ASB 92-62-010 S-92 ALERT
Basic Issue ▪ January 26/22 SERVICE BULLETIN
Page 15 
ATA
62-31-01
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
H. Record of compliance: 
(1) Make helicopter logbook entries to show compliance with this ASB as follows: 
(a) Make helicopter level logbook entry on form SA7343-15 (Aircraft ASB Release 
Signoff). 
(b) When ASB modifies a component that can be removed from this helicopter: 
1. Make component log card entries on forms SA7343-22 (Aircraft Component 
Log Cards) and SA7343-21 (Component Log Cards), as applicable. 
2. If a component modified by this ASB does not have a log card and the ASB 
does not create one, then annotate compliance on the next higher assembly 
that the component belongs to which does have a log card. 
 If access to www.Sikorsky360.com is unavailable, complete attached ALERT 
SERVICE BULLETIN COMPLIANCE RECORD CARD and return it to Sikorsky 
Aircraft Corporation. 
(2) Make an appropriate electronic compliance entry in the E-Notification section at 
www.Sikorsky360.com. Refer to User Guide located on the www.Sikorsky360.com/E-
Notification Search page. 
This document/file contains export controlled information. See WARNING on first page.

### Page 16

(Fold over and tape closed) 
SIKORSKY AIRCRAFT CORPORATION 
FACSIMILE NUMBER (817) 762-6715 
EMAIL ADDRESS: product_safety.gr-sik@lmco.com 
ATTENTION: Gr-SIK, Product_Safety 
SIKORSKY AIRCRAFT CORPORATION 
(Fold Up to Arrows)
IMPORTANT NOTICE 
Upon COMPLIANCE with the attached ASB, Sikorsky requests your cooperation 
in completing and returning this ENTIRE PAGE by MAIL, FAX, or scan & 
EMAIL. 
Please fill in the requested information at the bottom of the page, so we may maintain 
proper records documenting the configuration of your aircraft. This information is useful 
when determining configuration and effectivity of issues affecting fielded aircraft. 
This request is in keeping with our policy to assure that our customers receive the latest 
information applicable for the maintenance of your aircraft. Thank you. 
ALERT SERVICE BULLETIN:  ________________  Compliance Record Card 
TITLE:  ___________________________________________________________________  
 ___________________________________________________________________  
 ___________________________________________________________________  
OWNER/OPERATOR:  _____________________________________________________  
SUBMITTED BY:  ___________________________  DATE:  ____________________  
FOLLOWING SERIAL NUMBERS ARE NOT AFFECTED BY THIS ASB 
ASB HAS BEEN COMPLIED WITH ON HELICOPTER SERIAL NUMBERS: 
 ___________   ___________   ___________   ___________   ___________   ___________  
 ___________   ___________   ___________   ___________   ___________   ___________  
ASB 92-62-010
ROTORS – Main Rotor (MR) Swashplate Assembly – One-Time Inspection of MR 
Stationary Swashplate Assembly to Initiate a 50-Hour Recurring Inspection

### Page 17

No Postage 
Necessary 
BUSINESS REPLY MAIL 
FIRST-CLASS MAIL PERMIT NO. 432 BRIDGEPORT CT 
POSTAGE WILL BE PAID BY ADDRESSEE 
SIKORSKY AIRCRAFT CORPORATION 
Global Commercial & Military Systems 
Mailstop K100
124 QUARRY ROAD 
TRUMBULL, CT 06611 U.S.A. 
ATTENTION:   
Gr-SIK, Product_Safety 
Please complete the form on the reverse side and FAX to 
FACSIMILE NUMBER (817) 762-6715 
Or scan and email to: 
EMAIL ADDRESS: product_safety.gr-sik@lmco.com 
or fold and return ENTIRE form to Sikorsky Aircraft Corporation

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
