# Sikorsky Alert Service Bulletin 92-67-006

Copy: Revision A ("Sikorsky Alert Service Bulletin ASB 92-67-006 Rev A"), 19 pages: PDF https://openairdocs.org/files/sha256/a4/05/a40590dc7ae55ba550968cbe2c8210502618a320adee4431d2745b458aeed687; text https://openairdocs.org/service-documents/sikorsky/sb-92-67-006/file/a40590dc7ae5.md. Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2016-4280, the docket of AD 2016-05-11. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Sikorsky](https://openairdocs.org/service-documents/sikorsky.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 92-67-006
- Latest revision known: 92-67-006, Revision A (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/sikorsky/sb-92-67-006

## Text (19 pages)

Rights: © Sikorsky. Filed by the FAA in regulations.gov docket FAA-2016-4280, the docket of AD 2016-05-11. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 of 17 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
S-92®HELICOPTER 
ALERT SERVICE  
BULLETIN 
NOTICE TO ALL PERSONS RECEIVING THIS DOCUMENT: 
WARNING: THIS DOCUMENT, OR AN EMBODIMENT OF IT IN ANY MEDIA, DISCLOSES INFORMATION WHICH IS PROPRIETARY, IS THE PROPERTY OF SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES, IS 
AN UNPUBLISHED WORK PROTECTED UNDER APPLICABLE COPYRIGHT LAWS, AND IS DELIVERED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED, DISCLOSED, REPRODUCED, IN WHOLE OR IN PART 
(INCLUDING REPRODUCTION AS A DERIVATIVE WORK), OR USED FOR MANUFACTURE FOR ANYONE OTHER THAN SIKORSKY AIRCRAFT CORPORATION AND/OR ITS SUBSIDIARIES WITHOUT ITS WRITTEN CONSENT, 
AND THAT NO RIGHT IS GRANTED TO DISCLOSE OR SO USE ANY INFORMATION CONTAINED HEREIN. ALL RIGHTS RESERVED. ANY ACT IN VIOLATION OF APPLICABLE LAW MAY RESULT IN CIVIL AND CRIMINAL 
PENALTIES. 
S-92®IS A REGISTERED TRADEMARK OF SIKORSKY AIRCRAFT CORPORATION. 
ASB 92-67-006 
February 16/16 
Revision A ▪ February 19/16 
SUBJECT: FLIGHT CONTROLS – Pushrods – One-Time Inspection of Main Rotor and Tail Rotor Servo 
Pushrods 
Section 1. PLANNING INFORMATION 
A. Effectivity S- 92A model helicopters with serial numbers 920006 through 920291. 
B. Purpose To provide instructions to inspect for proper pushrod assembly. 
C. Background Main rotor servo input pushrods and tail rotor servo pushrods were found with 
incorrect safety cable routing, incorrect jam nut torque, and/or incorrect locking 
device serrations and keys engagement. 
D. Description Helicopter is prepared for inspection. Flight control rods are inspected for safety 
cable routing, engagement of serrations of locking device, engagement of keys on 
locking device, thread engagement, and torque of jamnuts. Non-compliant 
inspection results are documented on Pushrod Data Sheet. If any discrepancies 
are found, applicable pushrod is removed, reworked, reinstalled, or replaced. Rig 
check is performed, as required. Helicopter is returned to service. 
E. Compliance Compliance is essential. The inspection outlined herein must be accomplished no 
later than May 16, 2016. 
 
Sikorsky Aircraft Corporation 
6900 Main StreetP.O. Box 9729 
Stratford, Connecticut 06615-9129 
(203) 386-4000 
 S-92
WARNING ‒ This information contains technical data subject to the EAR. Diversion contrary to US Law is prohibited. ECCN: 9E991

### Page 2

S-92 ALERT ASB 92-67-006 
SERVICE BULLETIN Revision A ▪ February 19/16 
 
Page 2 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 1. PLANNING lNFORMATION (Continued) 
F. Approval Inspection item. 
G. Manpower (Estimated) 
Task No. of Men No. of Hours Man-Hours* 
Inspection of Flight Control Pushrods 1 2.0 2.0 
Rework of Flight Control Pushrods 1 2.0 2.0 
Performance of Rig Check 2 1.0 2.0** 
Total Man-Hours   6.0 
*Estimate does not include time required to prepare helicopter or return it to flight status. 
**Estimated time is for passing a rig check on the first attempt. 
 
H. Tooling 
Qty Nomenclature Part No. Source 
1 Lighted Borescope Commercially available or equivalent (1) 
1 Inspection Mirror Commercially available or equivalent (1) 
1 Torque Wrench (30 - 150 in. lbs.) Commercially available or equivalent (1) 
1 Torque Wrench (150 - 750 in. 
lbs.) 
Commercially available or equivalent (1) 
(1) Available through normal supply channels. 
I. Weight and Balance 
Not a
ffected. 
J. Electrical Load Data 
Not affected. 
K. Software Load Data 
Not changed. 
L. References 
(1) Maintenance Manual, SA S92A-AMM-000, Task 21- 23-02-900-003/-004. 
(2) Maintenance Manual, SA S92A-AMM-000, Task 53-70-00-900-001. 
(3) Maintenance Manual, SA S92A-AMM-000, Task 54- 72-03-900-003/-004. 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 3

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 3 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 1.    PLANNING INFORMATION (Continued) 
(4) Maintenance Manual, SA S92A-AMM-000, Chapter/Section 67- 00-07. 
(5) Maintenance Manual, SA S92A-AMM-000, Task 67- 11-04-960-009. 
(6) Maintenance Manual, SA S92A-AMM-000, Task 67- 12-03-960-005. 
(7) Maintenance Manual, SA S92A-AMM-000, Task 67- 14-04-960-002. 
(8) Maintenance Manual, SA S92A-AMM-000, Task 67- 14-05-900-001/-002. 
(9) Maintenance Manual, SA S92A-AMM-000, Task 67-14-06-960-001. 
(10) Maintenance Manual, SA S92A-AMM-000, Task 67- 21-04-960-007. 
(11) Maintenance Manual, SA S92A-AMM- 000, Task 67-23-01-960-007. 
M. Publications Affected 
(1) Temporary Revision No. 5- 173 against Maintenance Manual, SA S92-AWL-000, Task 5-
20-00-200-007, is issued concurrently with this ASB. 
(2) Temporary Revision No. 67- 09 against Maintenance Manual, SA S92-AMM-000, Task 67-
11-04-960-009, will be issued at a later date. 
(3) Temporary Revision No. 67- 10 against Maintenance Manual, SA S92-AMM-000, Task 67-
12-03-960-005 and 67-12-03-300-002, will be issued at a later date. 
(4) Temporary Revision No. 67- 11 against Maintenance Manual, SA S92-AMM-000, Task 67-
14-04-960-002, will be issued at a later date. 
(5) Temporary Revision No. 67- 12 against Maintenance Manual, SA S92-AMM-000, Task 67-
14-06-960-001, will be issued at a later date. 
(6) Temporary Revision No. 67- 13 against Maintenance Manual, SA S92-AMM-000, Task 67-
21-04-960-007, will be issued at a later date. 
(7) Temporary Revision No. 67- 14 against Maintenance Manual, SA S92-AMM-000, Task 67-
23-01-960-007, will be issued at a later date. 
(8) Temporary Revision No. 67- 15 against Maintenance Manual, SA S92-AMM-000, Task 
Chapter/Section 67-00-00, is issued concurrently with this ASB. 
N. Attachment 
None. 
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 4

S-92 ALERT ASB 92-67-006 
SERVICE BULLETIN Revision A ▪ February 19/16 
 
Page 4 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 2. MATERIAL INFORMATION 
A. Basis for Material Data 
Per helicopter. 
B. Bill of Material 
None. 
C. Consumable Material 
 
Qty Nomenclature Part No. Source 
A/R 0.02 Inch Diameter Safety Cable Commercially available or equivalent (1) 
A/R 0.02 Inch Diameter Safety Wire Commercially available or equivalent (1) 
(1) Procure locally. 
Section 3. ACCOMPLISHMENT INSTRUCTIONS 
 
A. Prepare helicopter for modification: 
 
(1) Turn off all helicopter electrical and hydraulic power. 
(2) Engage rotor brake. 
 
 
TO PREVENT ELECTRICAL SHOCK OF PERSONNEL OR POSSIBLE 
DAMAGE TO HELICOPTER COMPONENTS, MAKE SURE TO TURN 
OFF ALL ELECTRICAL POWER. 
WHEN ANY COMPONENT OF ANY FLIGHT CONTROL SYSTEM IS 
DISCONNECTED, REMOVED, AND REINSTALLED OR REPLACED, 
A RIGGING CHECK OF THE AFFECTED SECTION MUST BE MADE 
TO BE SURE THAT CONTROL RANGES ARE WITHIN SPECIFIED 
LIMITS. 
OBSERVE ALL CAUTIONS AND WARNINGS ON CONTAINERS 
WHEN USING CONSUMABLES. WHEN APPLICABLE, WEAR 
NECESSARY PROTECTIVE GEAR DURING HANDLING AND USE. IF 
A CONSUMABLE IS FLAMMABLE OR EXPLOSIVE, MAKE CERTAIN 
CONSUMABLE AND ITS VAPORS ARE KEPT AWAY FROM HEAT, 
SPARK AND FLAME. MAKE CERTAIN FIREFIGHTING EQUIPMENT 
IS READILY AVAILABLE PRIOR TO USE. FOR ADDITIONAL 
INFORMATION ON TOXICITY, FLASHPOINT AND FLAMMABILITY 
OF CHEMICALS, CONSULT YOUR MEDICAL PEOPLE OR THE 
MANUFACTURER OF THE CONSUMABLE. 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 5

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 5 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(3) Open main rotor pylon sliding fairing. (Refer to Maintenance Manual, SA S92A-AMM-000, 
Task 53-70-00-900-001). 
(4) Remove tail rotor servo fairing assembly. (Refer to Maintenance Manual, SA S92A-AMM-
000, Task 54-72-03-900-003). 
(5) Remove mixer top plate. (Refer to Maintenance Manual, SA S92A-AMM-000, Task 67- 14-
05-900-001). 
(6) If necessary, remove air conditioning crossover duct (92309-04818-101/-104). (Refer to 
Maintenance Manual, SA S92A-AMM-000, Task 21-23-02-900-003). 
(7) If necessary, remove applicable interior panels. (Refer to Maintenance Manual, SA S92A-
AMM-000, Chapter 25). 
NOTE: Perform all of the following inspections before correcting any non-conformities. 
B. Inspect flight control pushrods listed in Table 1 as follows (Figure 1): 
(1) Visually inspect adjustable ends of pushrods for proper safety cable routing. Right hand 
threads shall have safety cable routed as shown in Figure 2. Left hand threads shall have 
safety cable routed as shown in Figure 3. If safety cable is installed incorrectly, record 
results on Pushrod Data Sheet. (Refer to Pushrod Data Sheet, step K.). 
NOTE: Use of a lighted borescope (commercially available or equivalent) may aid 
during inspection. 
(a) For upper deck quadrant pushrod (92400-04802-105) only, if safety cable is 
incorrect, access must be gained to the pushrod and steps B.(2), B.(3), and B.(4) 
must be performed. Steps B.(3)(a) and B.(4)(a) cannot be applied. 
NOTE: Use of a lighted borescope (commercially available or equivalent) may aid while 
inspecting upper deck quadrant pushrod (92400-04802-105). 
(2) Where locking devices are used, visually inspect adjustable ends of pushrods for proper 
engagement of serrations and keys of the locking device. If serrations and keys of locking 
device are not properly engaged, record results on Pushrod Data Sheet. (Refer to Pushrod 
Data Sheet, step K.). (Refer to Figure 4). 
(3) Inspect adjustable ends of pushrods for minimum thread engagement. Check that 
adjustable rod end, or clevis, is threaded beyond the inspection hole and that 0.02 inch 
diameter safety wire (commercially available or equivalent) cannot be inserted through the 
hole.If adjustable ends of pushrods do not have proper thread engagement, record results 
on Pushrod Data Sheet. (Refer to Pushrod Data Sheet, step K.). 
 
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 6

S-92 ALERT ASB 92-67-006 
SERVICE BULLETIN Revision A ▪ February 19/16 
 
Page 6 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
NOTE: Use of a lighted borescope (commercially available or equivalent) may aid 
while inspecting upper deck quadrant pushrod (92400-04802-105). 
(a) For upper deck quadrant pushrod (92400-04802-105) only, if safety cable is installed 
correctly, locking devices pass visual inspection, and an acceptable maintenance 
phase inspection that would allow access to the pushrod does not coincide with the 
accomplishment of this ASB, step B.(3) can be deferred until the pushrod is 
accessible and step B.(3)(b) and B.(3)(c) can be performed as an alternate means of 
compliance. The procedure in step B.(3) above shall be accomplished the next time 
the pushrod is accessible, not to exceed the next 1500 hour inspection if not done at 
this time 
(b) If B.(3) is deferred for the upper deck quadrant pushrod (92400-04802-105), a visual 
inspection is required to confirm that threads are visible in the inspection hole. If 
threads are not visible, record results on Pushrod Data Sheet and proceed to step 
B.(4).  Step B(4)(a) cannot be applied. 
(c) If B.(3) is deferred for the upper deck quadrant pushrod (92400-04802-105), record 
the inspection requirement in the helicopter logbook. 
NOTE: Do not turn pushrod tube to determine looseness of jamnut or fasteners. 
(4) For all adjustable pushrods, check jamnut for looseness using finger pressure with safety 
cable removed. Jamnut shall not turn in either direction. If jamnut moves with finger 
pressure, record results on Pushrod Data Sheet. (Refer to Pushrod Data Sheet, step K.). 
(a) For upper deck quadrant pushrod (92400-04802-105) only, if safety cable is installed 
correctly, locking devices pass visual inspection, threads are visible through the 
inspection hole, and an acceptable phase inspection that would allow access to the 
pushrod does not coincide with the accomplishment of this ASB, step B.(4) can be 
deferred until the pushrod is accessible and step B.(4)(b) and B.(4)(c) can be 
performed as an alternate means of compliance. The procedure in step B.(4) above 
shall be accomplished the next time the pushrod is accessible, not to exceed the 
next 1500 hour inspection if not done at this time. 
(b) If B.(4) is deferred for the upper deck quadrant pushrod (92400-04802-105), a visual 
inspection in the interim is required to confirm that there is no clearance between the 
jam nut, locking device, and pushrod insert around the entire periphery of these 
items. If clearance is present, gain access to the pushrod and check jamnut for 
looseness using finger pressure, with safety cable removed. Jamnut shall not turn in 
either direction. If jamnut moves with finger pressure, record results on Pushrod 
Data Sheet.  
(c) If B.(4) is deferred for the upper deck quadrant pushrod (92400-04802-105), record 
the inspection requirement in the helicopter logbook.   
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 7

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 7 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
PUSHROD IDENTIFICATION - TABLE 1 
NOMENCLATURE PART NUMBER TORQUE VALUE TASK NUMBER 
Yaw Boost Input Pushrod 92400-04801-108 60-100 inch 
pounds 
67-21-04-960-007 
Pitch Boost Input Pushrod 92400-04801-107 43 inch-pounds 67-11-04-960-009 
Collective Boost Input Pushrod 92400-04801-107 350 inch-pounds 67-12-03-960-005 
Roll Boost Input Pushrod 92400-04801-109 43 inch pounds 67-11-04-960-009 
Yaw Boost Out Pushrod 92400-04802-109 40-46 inch-pounds 67-14-04-960-002 
Roll Boost Out Pushrod 92400-04803-103 40-46 inch-pounds 67-14-04-960-002 
Pitch Boost Out Pushrod 92400-04803-102 40-46 inch-pounds 67-14-04-960-002 
Collective Boost Out Pushrod 92400-04802-108 40-46 inch-pounds 67-14-04-960-002 
Limiter Pushrod 92400-04803-106 40-46 inch-pounds 67-14-04-960-002 
Pitch to Roll Pushrod 92400-04803-107 40-46 inch-pounds 67-14-04-960-002 
Left Hand Main Rotor Servo Pushrod 92400-04801-110 350 inch-pounds 67-14-06-960-001 
Forward Main Rotor Servo Pushrod 92400-04801-111 350 inch-pounds 67-14-06-960-001 
Right Hand Main Rotor Servo Pushrod 92400-04801-112 350 inch-pounds 67-14-06-960-001 
Upper Deck Quadrant Pushrod 92400-04802-105 60-100 inch-
pounds 
67-21-04-960-007 
Tail Rotor Servo Input Pushrod 92400-04802-107 40-46 inch-pounds 67-23-01-960-007 
    
NOTE: If safety cable is routed properly, keys and serrations are properly engaged, thread is 
properly engaged, and jamnut does not move, proceed to step D. 
C. Disposition of Non-Conforming Material: 
(1) If jamnut inspected in step B.(4) failed the finger pressure check, perform the following: 
(a) Remove and replace pushrod per applicable AMM task. If a replacement part is not 
readily available, contact Sikorsky Aircraft Corporation for inspection instructions to 
determine if pushrod may be suitable for limited use. 
(2) If threads inspected in step B.(3) are not properly engaged, perform the following: 
(a) Gain access to applicable control rod, as required. 
(b) Remove applicable pushrod. (Refer to task listed in Table 1). 
(c) Measure and record length from mounting centers. 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 8

S-92 ALERT ASB 92-67-006 
SERVICE BULLETIN Revision A ▪ February 19/16 
 
Page 8 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(d) Measure and record rod end, or clevis, orientation. 
(e) If required, remove safety cable. 
NOTE: Make sure serrations and key are properly engaged. 
(f) Reassemble rod end, jamnuts, and locking device. 
(g) Adjust to recorded length and rod end, or clevis, orientation. 
(h) Install applicable pushrod. (Refer to task listed in Table 1). 
(i) Check that adjustable rod end, clevis, and adjuster are threaded beyond the 
inspection hole such that a 0.02 inch diameter safety wire cannot be inserted 
through hole. 
(j) Using torque wrench (commercially available or equivalent), torque jamnut. (Refer to 
task and torque value listed in Table 1). 
NOTE: Make sure safety cable is routed in the proper direction for left hand or right 
hand thread. (Refer to Figures 2 and 3). 
(k) Install safety cable. 
(l) If required, perform quick rigging check. (Refer to Maintenance Manual, SA S92A-
AMM-000, Chapter/Section 67-00-07). 
(m) Proceed to step E. 
(3) If serrations and keys of the locking device inspected in step B.(2) are not properly 
engaged, perform the following: 
(a) Gain access to applicable control rod, as required. 
(b) If required, remove safety cable. 
(c) Back off jamnut and inspect locking device for damage. Replace locking device as 
required. (Refer to task listed in Table 1). 
(d) Using torque wrench (commercially available or equivalent), torque jamnut. (Refer to 
task and torque value listed in Table 1) 
NOTE: Make sure safety cable is routed in the proper direction for left hand or right 
hand thread. (Refer to Figures 2 and 3). 
(e) Install safety cable. 
(f) If required, perform quick rigging check. (Refer to Maintenance Manual, SA S92A-
AMM-000, Chapter/Section 67-00-07). 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 9

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 9 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
(g) Proceed to step E. 
(4) If safety cable inspected in step B.(1) is installed incorrectly, perform the following: 
(a) Gain access to applicable control rod, as required. 
(b) If required, remove safety cable. 
(c) Using torque wrench (commercially available or equivalent), torque jamnut. Record if 
jamnut moves at minimum torque. (Refer to task and torque value listed in Table 1). 
NOTE: Make sure safety cable is routed in the proper direction for left hand or right 
hand thread. (Refer to Figures 2 and 3). 
(d) Install safety cable. 
(e) Proceed to step E. 
D. Disposition of Conforming Material: 
NOTE: For upper deck quadrant pushrod (92400-04802-105) only, proceed to step E if 
inspections B.(3) and B.(4) were deferred.  Add the torque wrench verification 
below to the logbook to be performed the next time the pushrod is accessible, not 
to exceed the next 1500 hour inspection if not done at this time, as an alternate 
means of compliance to step D.(1).  
(1) If safety cable is routed properly, keys and serrations are properly engaged, thread is 
properly engaged, and jamnut does not move with finger pressure, perform the following: 
(a) Using torque wrench (commercially available or equivalent), torque jamnut. (Refer t o 
task and torque value listed in Table 1). 
NOTE: Make sure safety cable is routed in the proper direction for left hand or right 
hand thread. (Refer to Figures 2 and 3). 
(b) Install safety cable. 
E. Install tail rotor servo fairing assembly. (Refer to Maintenance Manual, SA S92A-AMM-000, Task 
54-72-03-900-004). 
F. Install mixer top plate. (Refer to Maintenance Manual, SA S92A-AMM-000, Task 67- 14-05-900-
002). 
G. If removed, install air conditioning crossover duct (92309-04818-101/-104). (Refer to 
Maintenance Manual, SA S92A-AMM-000, Task 21-23-02-900-004). 
H. If removed, install applicable interior panels. (Refer to Maintenance Manual, SA S92A-AMM-000, 
Chapter 25). 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 10

S-92 ALERT ASB 92-67-006 
SERVICE BULLETIN Revision A ▪ February 19/16 
 
Page 10 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3.    ACCOMPLISHMENT INSTRUCTIONS (Continued) 
I. Close main rotor pylon sliding fairing. (Refer to Maintenance Manual, SA S92A-AMM-000, Task 
53
-70-00-900-001). 
J. Return helicopter to service. 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 11

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 11 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
K. Pushrod Data Sheet: 
(1) Report the non-conforming data, fax to facsimile number (860- 998-7565) or scan and email 
to: GPSIKSASProductSafet@utc.com. 
(2) Record the following information for each pushrod, and attach labeled photographs 
showing the same: 
Customer/Operator Name:    
Helicopter Serial Number:    
Pushrod Part Number:    
Pushrod Serial Number:    
Was safety cable installed correctly?          _______Yes                    _______No 
Were locking device serrations properly engaged? _______Yes _______No 
Was locking device key properly engaged?                                _______Yes                    _______No 
Did adjustable ends of pushrod have proper thread engagement?_______Yes_______No 
Was jamnut properly torqued?_______Yes _______No 
 
 
 
 
 
 
 
 
 
 
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 12 (OCR)

S-92 ALERT  ASB 92-67-006
SERVICE BULLETIN  Revision A • February 19/16
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
RATE PUSHROD
92400-04803-107
SEE DETAIL E  ITCH TO ROLI  92400-04803-103
SEE DETAIL B  STRO  ROLL BOOST OUT
PUSHROD
- SEE DETAIL D  92400-04802-109  YAW BOOST OUT
PUSHROD
SEE DETAIL C
SEE DETAIL A
92400-04801-107
COLLECTIVE BOOST  DOSTOUT
DETAIL B
92400-04801-107
PITCH BOOST INPUT
PET OR COURANT
DETAIL A
DETAIL C  TD3731_1
COMPONENT LOCATION
FIGURE 1 (SHEET 1 OF 2)
ATA  ONE-TIME
Page 12  67-00-00  INSPECTION
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 13 (OCR)

ASB 92-67-006  S-92 ALERT
Revision А • February 19/16  SERVICE BULLETIN
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
92400-04801-112
RIGHT HAND MAIN ROTOR
SERVO PUSHROD •
92400-04801-111
FORWARD MAIN ROTOR
SERVO PUSHROD
92400-04801-110
LEFT HAND MAIN ROTOR
SERVO PUSHROD
DETAIL D
92400-04802-107
TAIL ROTOR SERVO
INPUT PUSHROD
FWD
DETAIL E  TD373122
COMPONENT LOCATION
FIGURE 1 (SHEET 2)
ONE-TIME  ATA
INSPECTION  67-00-00  Page 13
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 14

S-92 ALERT ASB 92-67-006A 
SERVICE BULLETIN Revision A▪ February 19/16 
 
Page 14 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
RIGHT HAND THREAD SAFETY CABLE ROUTING 
FIGURE 2 
 
 
 
 
 
 
 
 
 
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 15

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 15 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
 
LEFT HAND THREAD SAFETY CABLE ROUTING 
FIGURE 3 
 
 
 
 
 
 
 
 
 
 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 16 (OCR)

S-92 ALERT  ASB 92-67-006A
SERVICE BULLETIN  Revision A- February 19/16
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued)
CORRECT ASSEMBLY OF LOCKING DEVICE
INCORRECT KEY ENGAGEMENT  INCORRECT SERRATION ENGAGEMENT
TD3734
LOCKING DEVICE INSTALLATION
FIGURE 4
ATA  ONE-TIME
Page 16  67-00-00  INSPECTION
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 17

ASB 92-67-006 S-92  ALERT 
Revision A ▪ February 19/16 SERVICE BULLETIN 
 
Page 17 
ATA 
67-00-00 
ONE-TIME 
INSPECTION 
Section 3. ACCOMPLISHMENT INSTRUCTIONS (Continued) 
L. Record of compliance: 
(1) Make helicopter logbook entries to show compliance with this ASB as follows: 
(a) Make helicopter level logbook entry on form SA7343- 15 (Aircraft ASB and CSN 
Release Signoff). 
(b) When ASB modifies a component that can be removed from this helicopter: 
1. Make component log card entries on forms SA7343-22 (Aircraft Component 
Log Cards) and SA7343-21 (Component Log Cards), as applicable. 
2. If a component modified by this ASB does not have a log card and the ASB 
does not create one, then annotate compliance on the next higher assembly 
that the component belongs to which does have a log card. 
NOTE: If access to www.Sikorsky360.com is unavailable, complete attached ALERT 
SERVICE BULLETIN COMPLIANCE RECORD CARD and return it to Sikorsky 
Aircraft Corporation. 
(2) Make an appropriate electronic compliance entry in the E-Notification section at 
www.Sikorsky360.com. Refer to User Guide located on the www.Sikorsky360.com/E-
Notification Search page. 
 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 18

(Fold over and tape closed) 
SIKORSKY AIRCRAFT CORPORATION 
FACSIMILE NUMBER (860) 998-7565 
EMAIL ADDRESS: GPSIKSASProductSafet@utc.com 
ATTENTION: PRODUCT SAFETY MANAGER 
SIKORSKY AIRCRAFT CORPORATION 
 
(Fold Up to Arrows) 
IMPORTANT NOTICE 
Upon COMPLIANCE with the attached ASB, Sikorsky requests your cooperation 
in completing and returning this ENTIRE PAGE by MAIL, FAX, or scan & 
EMAIL. 
Please fill in the requested information at the bottom of the page, so we may maintain 
proper records documenting the configuration of your aircraft. This information is useful 
when determining configuration and effectivity of issues affecting fielded aircraft. 
This request is in keeping with our policy to assure that our customers receive the latest 
information applicable for the maintenance of your aircraft. Thank you. 
ALERT SERVICE BULLETIN:  ________________  Compliance Record Card 
TITLE:  ___________________________________________________________________  
  ___________________________________________________________________  
  ___________________________________________________________________  
OWNER/OPERATOR:  _____________________________________________________  
SUBMITTED BY:  ___________________________  DATE:  ____________________  
FOLLOWING SERIAL NUMBERS ARE NOT AFFECTED BY THIS ASB 
ASB HAS BEEN COMPLIED WITH ON HELICOPTER SERIAL NUMBERS: 
 ___________   ___________   ___________   ___________   ___________   ___________  
 ___________   ___________   ___________   ___________   ___________   ___________  
                  
No. 92-67-006A 
FLIGHT CONTROLS – Pushrods – One-Time Inspection of Main Rotor and Tail 
Rotor Servo Pushrods 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

### Page 19

No Postage 
Necessary 
BUSINESS REPLY MAIL 
FIRST-CLASS MAIL PERMIT NO. 432 BRIDGEPORT CT 
POSTAGE WILL BE PAID BY ADDRESSEE 
SIKORSKY AIRCRAFT CORPORATION 
Commercial Systems and Services 
Mailstop K100 
124 QUARRY ROAD 
TRUMBULL, CT 06611 U.S.A.   
ATTENTION:  PRODUCT SAFETY MANAGER 
 SIKORSKY AIRCRAFT CORPORATION 
Please complete the form on the reverse side and FAX to 
FACSIMILE NUMBER (860) 998-7565 
Or scan and email to: 
EMAIL ADDRESS: GPSIKSASProductSafet@utc.com 
or fold and return ENTIRE form to Sikorsky Aircraft Corporation 
This document contains technical data subject to EAR. See WARNING and classifications on first page.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
