# Solo Kleinmotoren Service Bulletin 4603-18: No revision named

- Rights: © Solo Kleinmotoren. Filed by the FAA in regulations.gov docket FAA-2021-1015; AD 2022-04-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Solo Kleinmotoren Service Bulletin 4603-18](https://openairdocs.org/service-documents/solo/sb-4603-18.md)
- Title as filed: Solo Kleinmotoren Service Bulletin 4603-18
- Pages: 4
- PDF: https://openairdocs.org/files/sha256/46/43/4643da50b51ab79b9b7ee5d45af6312c250da7b5c4cc9c5bd05a5917bb20b244
- Page: https://openairdocs.org/service-documents/solo/sb-4603-18/file/4643da50b51a

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

solo 
KLEINMOTOREN GMBH 
Postfach 600152 
D71050 Sindelfingen 
Technische Mitteilung 
Service Bulletin 
4603 – 18 
Motor/Engine SOLO 2 350 
 
 
 
 
Seite 1 von 4 
 
 
Datum / Date: 
22.01.2019 
Ersetzte Ausgabe / replaced issue 
12.12.2018 
Verantw. Person/respons. person 
W. Emmerich 
 
 
Motortyp:  Solo 2350B, 2350BS, 2350C, 2350D 
Engine type:  Solo 2350B, 2350BS, 2350C, 2350D 
 
Gegenstand a) Einbau einer Mutter mit Flansch an der Exzenterachse. 
 b) Beschränkung der Lebensdauer der Kugellager am Lagerbock des 
Untersetzungsgetriebes auf 15 Jahre Betriebszeit. 
Subject a) Introduction of a nut with flange at the excentric axle. 
 b) Introduction of a lifetime limit of 15 years of operation for the ball bearings 
at the bearing block of the reduction gear. 
 
Betroffen:  Alle Werknummern der Motoren 2350B, 2350BS, 2350C und 2350D 
Affected  All serial numbers of the engines 2350B, 2350BS, 2350C and 2350D 
   Nicht betroffen, da in Serie eingeführt ab den Werknummern: 
   Not affected because in serial production from serial numbers: 
    
2350BS 2350C 2350D 
1134 2187 362 
 
Dringlichkeit Innerhalb 12 Monate nach Gültigkeit der PAD Nummer 19-004 
Urgency Within 12 months after the effective date of the PAD 19-004 
 
Vorgang a) Propeller vom Motor demontieren. Splint, Spannstift oder Drahtsicherung 
entfernen und Mutter an der Exzenterwelle lösen und abschrauben. Neue 
Mutter mit Flansch montieren und bis zum Anschlag festziehen. Dann wieder 
lösen bis eine der Nuten mit der Bohrung in der Exzenterachse fluchtet. 
Spannstift (bei 2350C), Splint (bei 2350B, 2350BS) oder Drahtsicherung 
(2350D) montieren. Propeller wieder montieren. Material siehe Materialliste. 
 b) Propeller vom Motor demontieren. Sicherungsstift, Splint oder 
Drahtsicherung entfernen und Mutter an der Exzenterwelle lösen und 
abschrauben. Klemmschrauben am Lagerbock lösen und Riemen durch 
verdrehen der Exzenterachse entspannen. Exzenterachse mit 
Riemenscheibe ausbauen. Kugellager wechseln (siehe Hinweise zum 
Zerlegen und Zusammenbau). Exzenterachse mit Riemenscheibe wieder 
einbauen. Riemen montieren und Riemenspannung durch Verdrehen der 
Achse einstellen. Propeller wieder montieren. 
Condition a) Dismantle the propeller from the engine. Remove the safety pin, cotter pin 
or the safety wire and dismantle the nut at the excentric shaft. Mount the 
new nut with flange up to the stop. Then loosen the nut until one of the slots 
in the nut is in line with the bore in the axle. Mount the spring-type pin 
(2350C), cotter pin (2350B, 2350BS) or the safety wire (2350D). Then mount 
the propeller.  Material see bill of material. 
 b) Dismantle the propeller from the engine. Remove the safety pin, the cotter 
pin or the safety wire and dismantle the nut at the excentric shaft. Loosen 
the clamping srews and loosen the tension of the drive belts by rotating the 
excentric shaft. Dismantle the shaft together with the pulley from the 
reduction gear. Replace the two ball bearings (See hints for dismantling and 
assembly). Assemble the excentric shaft together with the pulley to the 
reduction gear. Assemble the belts and adjust tension by rotating the 
excentric axle. Assemble the propeller to the pulley.

### Page 2

solo 
KLEINMOTOREN GMBH 
Postfach 600152 
D71050 Sindelfingen 
Technische Mitteilung 
Service Bulletin 
4603 – 18 
Motor/Engine SOLO 2 350 
 
 
 
 
Seite 2 von 4 
 
 
Datum / Date: 
22.01.2019 
Ersetzte Ausgabe / replaced issue 
12.12.2018 
Verantw. Person/respons. person 
W. Emmerich 
 
 
 
Maßnahmen Die Arbeiten sind von einer freigabeberechtigten Person freizugeben. 
Actions The change has to be released by certifying staff. 
 
Material Siehe folgende Liste 
 
Material See the following bill of material 
 
Teile die entfallen/Parts which are obsolete 
Pos. Teilenummer/
Part-No. 
Menge/Number 
of pieces 
Bezeichnung/Description 
Teil a) / part a) 
1 0042319 1 Splint / cotter pin 
2 0028143 1 Sechskantmutter / Hex-nut 
Teil b) / part b) 
1 0050110 2 Kugellager - 25 x 52 x 15 - 6205 - 2 RS / Ball 
bearing 
 
 
Neue Teile/New parts 
Pos. Teilenummer/
Part-No. 
Menge/Number 
of pieces 
Bezeichnung/Description 
Teil a) / part a) 
1 0028143-V2 1 Flanschmutter / flange-nut 
2 na 1 Sicherungsdraht / safety wire beim Motor 2350D  
3 0042319 1 Splint / cotter pin beim Motor 2350 B und BS, DG 
1000T, Antares 
4 0042323 
 
0042324 
1 
 
1 
Spannhülse ISO 8752 4,5x30/ Spring-type 
straight pin beim Motor 2350C (Ventus cm) 
Spannhülse ISO 8752 5x30/ Spring type straight 
pin wenn Bohrung in der Welle 5 mm 
 0510985 1 Teilesatz bestehend aus den Positionen 1 – 4 
Parts kit containing pos. 1 -4 
Teil b) / part b) 
1 0050110 2 Kugellager - 25 x 52 x 15 - 6205 - 2 RS / Ball 
bearing

### Page 3

solo 
KLEINMOTOREN GMBH 
Postfach 600152 
D71050 Sindelfingen 
Technische Mitteilung 
Service Bulletin 
4603 – 18 
Motor/Engine SOLO 2 350 
 
 
 
 
Seite 3 von 4 
 
 
Datum / Date: 
22.01.2019 
Ersetzte Ausgabe / replaced issue 
12.12.2018 
Verantw. Person/respons. person 
W. Emmerich 
 
 
 
Hinweis Zerlegen und Zusammenbau der Riemenscheibe mit Lagern. 
  
1. Riemenscheibe mit Achse und Lagern im Ofen auf 160°C 
erwärmen. Achse mit Stift nach hinten heraustreiben. Dabei 
verbleibt das hintere Lager auf der Achse (Bild 1). 
2. Vorderes Lager im warmen Zustand ausbauen (Bild 2) 
3. Lager von der Achse mit Abzieher ausbauen. 
4. Achse und Riemenscheibe reinigen. 
5. 1 Lager und die Riemenscheibe auf 160°C erwärmen (Bild 3). 
6. Erwärmtes Lager auf Achse stecken, beim Motor 2350D 
Distanzhülse aufstecken (Bild 4). 
7. Wenn das Lager wieder abgekühlt ist wird die Achse mit Lager 
in die erwärmte Riemenscheibe gesteckt (Bild 5). 
8. Vorderes Lager mit einer Presse montieren. Dabei kann die 
Riemenscheibe abgekühlt sein (Bild 6). 
9. Flanschmutter und Sicherung montieren wie oben beschrieben. 
 
Note Dismantling and assembly of the pulley with bearings. 
  
1. Heat the pulley with axle and bearings to 160°C (320°F). Drive 
axle with pin backwards. The rear bearing remains on the axle. 
(Pic. 1). 
2. Remove the front bearing in hot condition (Pic. 2). 
3. Remove the bearing on the axle with a puller. 
4. Clean axle and pulley 
5. Heat 1 bearing and the pulley to 160°C (320°F) (Pic.3) 
6. Assemble the heated bearing with the axle. Assemble the 
spacer with the axle for the engine 2350D (Pic. 4). 
7. After the bearing on the axle has cooled down to room 
temperature assemble the axle with the bearing into the heated 
pulley (Pic. 5) 
8. Assemble the front bearing with a manual press. The pulley can 
be at room temperature (Pic. 6) 
9. Assemble the safety nut and the safeguard as described 
above.

### Page 4

solo 
KLEINMOTOREN GMBH 
Postfach 600152 
D71050 Sindelfingen 
Technische Mitteilung 
Service Bulletin 
4603 – 18 
Motor/Engine SOLO 2 350 
 
 
 
 
Seite 4 von 4 
 
 
Datum / Date: 
22.01.2019 
Ersetzte Ausgabe / replaced issue 
12.12.2018 
Verantw. Person/respons. person 
W. Emmerich 
 
 
Bilder / Pictures 
 
 
Bild 1 / Picture 1 
  
Bild 2 / Picture 2 
 
Bild 3 / Picture 3 
 
Bild 4 / Picture 4 
 
Bild 5 / Picture 5 
 
Bild 6 / Picture 6

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
