# Solo Kleinmotoren Service Bulletin 4603-19: No revision named

- Rights: © Solo Kleinmotoren. Filed by the FAA in regulations.gov docket FAA-2022-1406, the docket of AD 2023-03-22. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Solo Kleinmotoren Service Bulletin 4603-19](https://openairdocs.org/service-documents/solo/sb-4603-19.md)
- Title as filed: Solo Kleinmotoren GmbH Service Bulletin 4603-19
- Pages: 4
- PDF: https://openairdocs.org/files/sha256/de/b0/deb0810c3dfb6eb1c6a2ba777b882581c41044a8e464dd9ab21ee2fdcfe66aa6
- Page: https://openairdocs.org/service-documents/solo/sb-4603-19/file/deb0810c3dfb

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

solo  
KLEINMOTOREN GMBH  
Postfach 600152  
D71050 Sindelfingen  
Technische Mitteilung  
Service Bulletin  
4603 – 19  
Motor/Engine SOLO 2 350D  
  
  
  
  
Seite 1 von 4  
Datum / Date:  
31.01.2022  
Ersetzte Ausgabe / replaced issue  
 
Verantw. Person/respons. person 
W. Emmerich  
 
Motortyp:    Solo 2350D  
Engine type:   Solo 2350D  
  
Gegenstand:  Exzenterachse am Lagerbock des Untersetzungsgetriebes 
Subject:  Eccentric shaft at the reduction gear  
Betroffen:    Alle Werknummern der Motoren 2350D bis einschließlich 399 
(nicht betroffen sind alle Werknummern ab 399+1) 
Affected:   All serial numbers of the engines 2350D up to and including 399 
(Not affected are all serial numbers from 399+1 and on) 
Dringlichkeit:  Spätestens bei einer Betriebszeit des Motors von 30h 
Urgency : Latest with 30h engine operating time 
Vorgang:  Bei einem Motor versagte die Exzenterachse. Deshalb wird eine verbesserte 
Exzenterachse eingeführt und es wird ein Austauschintervall von 50 
Betriebsstunden für die Exzenterachse eingeführt. 
 
Condition:  In one engine, the eccentric axle failed. Therefore, an improved eccentric 
axle is introduced and a replacement interval of 50 operating hours for the 
eccentric axle is introduced. 
Maßnahme 1: Austausch der Exzenterachse gegen die verbesserte Exzenterachse 
Teilenummer 2031211V2 mit Scheibe Teilenummer 0032142. 
Maßnahme 2:  Einpflegen Änderung 4 im Handbuch für den Motor 2350 D 
Action 1: Replace the eccentric axle with the improved eccentric axle part number 
2031211V2 with washer part number 0032142. 
Action 2: 
 
 
 
 
 
 
 
 
Implement change 4 in the manual for the engine 2350 D.

### Page 2

solo  
KLEINMOTOREN GMBH  
Postfach 600152  
D71050 Sindelfingen  
Technische Mitteilung  
Service Bulletin  
4603 – 19  
Motor/Engine SOLO 2 350D  
  
  
  
  
Seite 2 von 4  
Datum / Date:  
31.01.2022  
Ersetzte Ausgabe / replaced issue  
 
Verantw. Person/respons. person 
W. Emmerich  
  
Material:  Siehe folgende Liste  
Material: See the following bill of material  
 
  Teile die entfallen/Parts which are obsolete  
Pos.  Teilenummer/ 
Part-No.  
Menge/Number  
of pieces  
Bezeichnung/Description  
1  2031211  1  Exzenterachse / eccentric shaft 
2   Motorhandbuchseiten 1, 4, 5 
/ Engine manual, pages 1, 4, 5 
  
  
  Neue Teile/New parts  
Pos.  Teilenummer/ 
Part-No.  
Menge/Number  
of pieces  
Bezeichnung/Description  
1  na  1 Sicherungsdraht / safety wire  
2  2031211V2 1 Achse / Shaft 
3 0032142 1 Messing-Scheibe / Spacer 
4   Handbuchseiten Änderung 4, Handbuch für Motor 
2350 D 
Manual pages revision 4, Manual for Engine 2350 D 
 
Hinweis 1: Falls zur Aufrechterhaltung der Lufttüchtigkeit Part M (Anhang I zu Verordnung 
(EC) Nr. 2042/2003 mit allen gültigen Erweiterungen) anzuwenden ist, darf 
Maßnahme 2 im Rahmen der Erlaubnis zur eingeschränkten Pilot/Eigentümer 
Wartung durchgeführt werden. 
 
Die auszutauschenden Handbuchseiten können kostenlos vom SOLO 
AIRCRAFT ENGINES Internetangebot heruntergeladen werden. 
Die Änderungsseiten oder komplette Handbücher können auch in Papierform bei 
SOLO VERTRIEBS- UND ENTWICKLUNGS GmbH bezogen werden. 
 
Note 1 If Part-M (annex I to regulation (EC) No. 2042/2003 with all valid amendments) 
applies for continuing airworthiness, action 2 can be accomplished under the 
scope of the limited pilot-owner maintenance authorisation. 
 
The amended manual pages may be downloaded from the SOLO AIRCRAFT 
ENGINES website free of charge. Amended manual pages or complete amended 
manuals in paper form may be ordered from SOLO VERTRIEBS- UND 
ENTWICKLUNGS GmbH.

### Page 3

solo  
KLEINMOTOREN GMBH  
Postfach 600152  
D71050 Sindelfingen  
Technische Mitteilung  
Service Bulletin  
4603 – 19  
Motor/Engine SOLO 2 350D  
  
  
  
  
Seite 3 von 4  
Datum / Date:  
31.01.2022  
Ersetzte Ausgabe / replaced issue  
 
Verantw. Person/respons. person 
W. Emmerich  
 
Hinweis 2 Zerlegen und Zusammenbau der Riemenscheibe mit Lagern.  
 1. Bestehende Flanschmutter lösen, auf neue Achse drehen und Loch 
4,2 mm für Sicherungsdraht bohren. 
2. Riemenscheibe mit Achse und Lagern im Ofen auf 160°C 
erwärmen. Achse mit Stift nach hinten heraustreiben. Dabei 
verbleibt das hintere Lager auf der Achse (Bild 1).  
3. Vorderes Lager im warmen Zustand ausbauen (Bild 2)  
4. Lager von der Achse mit Abzieher ausbauen.  
5. Riemenscheibe reinigen.  
6. 1 Lager und die Riemenscheibe auf 160°C erwärmen (Bild 3).  
7. Erwärmtes Lager auf die neue Achse stecken, Distanzhülse 
aufstecken (Bild 4).  
8. Wenn das Lager wieder abgekühlt ist wird die Achse mit Lager in 
die erwärmte Riemenscheibe gesteckt (Bild 5).  
9. Vorderes Lager mit einer Presse montieren. Dabei kann die 
Riemenscheibe abgekühlt sein (Bild 6).  
10. Flanschmutter und Sicherung montieren wie oben 
beschrieben. 
 
Note 2 Dismantling and assembly of the pulley with bearings.  
  1. Loosen existing flange-nut, screw it on the new axle and drill hole 
4.2 mm for safety wire. 
2. Heat the pulley with axle and bearings to 160°C (320°F). Drive axle 
with pin backwards. The rear bearing remains on the axle. (Pic. 1).  
3. Remove the front bearing in hot condition (Pic. 2).  
4. Remove the bearing on the axle with a puller.  
5. Clean pulley  
6. Heat 1 bearing and the pulley to 160°C (320°F) (Pic.3)  
7. Assemble the heated bearing with the new axle. Assemble the 
spacer with the axle (Pic. 4).  
8. After the bearing on the axle has cooled down to room temperature 
assemble the axle with the bearing into the heated pulley (Pic. 5)  
9. Assemble the front bearing with a manual press. The pulley can be 
at room temperature (Pic. 6)  
10. Assemble the safety nut and the safeguard as described 
above.

### Page 4

solo  
KLEINMOTOREN GMBH  
Postfach 600152  
D71050 Sindelfingen  
Technische Mitteilung  
Service Bulletin  
4603 – 19  
Motor/Engine SOLO 2 350D  
  
  
  
  
Seite 4 von 4  
Datum / Date:  
31.01.2022  
Ersetzte Ausgabe / replaced issue  
 
Verantw. Person/respons. person 
W. Emmerich  
 
Bilder / Pictures  
  
Bild 1 / Picture 1  
  
Bild 2 / Picture 2  
  
Bild 3 / Picture 3  
  
Bild 4 / Picture 4  
  
Bild 5 / Picture 5  
  
Bild 6 / Picture 6

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
