# Trig Avionics Service Bulletin SUP/KT74/005: Revision 1

- Rights: © Trig Avionics. Filed by the FAA in regulations.gov docket FAA-2018-1081; AD 2019-13-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Trig Avionics Service Bulletin SUP/KT74/005](https://openairdocs.org/service-documents/trig-avionics/sup-kt74-005.md)
- Title as filed: SUP.KT74.005 KT74 Cam Service Bulletin Issue 1.0
- Pages: 3
- PDF: https://openairdocs.org/files/sha256/34/0e/340e5bcaddc115ec7bcc093486f5cec9c7a8e39345f841da7e05f1958a5d6be0
- Page: https://openairdocs.org/service-documents/trig-avionics/sup-kt74-005/file/340e5bcaddc1

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Trig Avionics Limited Service Bulletin  Page 1 of 3 
SUP/KT74/005 Issue 1.0  1 October 2018 
 
KT74 SERVICE BULLETIN 
Identifier: SUP/KT74/005 ISSUE 1.0 
 
DATE:  1st October 2018 
 
SUBJECT:  KT74 retaining cam replacement 
_____________________________________________________________________ 
APPLICABILITY 
This Service Bulletin applies to KT74 transponders approved under ETSO 
authorisation EASA.21O.10046583, part number 01157-00-(XX) and part number 
01158-00-(XX) which are: 
Serial number from 01143 to 02955; 
Modification Level 0; 
Installed in an orientation which is NOT a conventional aft-facing avionics 
stack mounting. 
PURPOSE 
Trig has determined that KT74 transponders in the listed serial number range may 
have been assembled with a retaining cam that could fail when installed in an 
unconventional orientation. 
The retaining cam is a small nylon part that engages in the mounting tray when the 
transponder is installed in the aircraft.  Although this has no effect on the normal 
operation of the transponder, the retaining cam is required to withstand very high 
loads during an impact to prevent the transponder coming out of the mounting tray. 
The transponders with the retaining cam that fall into the serial number range listed 
above have been re-tested and meet the crashworthiness requirements when mounted 
in a typical avionics rack oriented in the conventional manner (control panel facing 
aft, with the transponder level or angled upward).  If however the transponder is 
mounted in an unusual orientation, for example if it is mounted facing forward at a 
third crew member station on a larger aircraft, it may not meet the intended aircraft 
crashworthiness level. 
The retaining cams cannot be easily identified by visual inspection.  For any 
transponder in the affected range that is installed in any way other than with the 
connectors toward the nose of the aircraft the retaining cam must be replaced.

### Page 2

Trig Avionics Limited Service Bulletin  Page 2 of 3 
SUP/KT74/005 Issue 1.0  1 October 2018 
DESCRIPTION  
This bulletin describes the process removing the transponder, checking the Mod 
Level, and if required, returning the transponder to Trig Avionics for replacement or 
repair. 
COMPLIANCE 
This service bulletin is MANDATORY. This service bulletin must be accomplished 
within 6 months. 
The technical content of this document has been produced in accordance with 
alternative procedure to DOA reference AP205. 
EQUIPMENT REQUIRED 
Standard aircraft tools for removal of the transponder. 
A ramp test set to verify correct reinstallation of the transponder after inspection 
and/or rectification. 
ACCOMPLISHMENT INSTRUCTIONS 
1. Review the transponder installation.  If the transponder is installed in a 
conventional aft-facing avionics rack, you may record compliance with this 
Service Bulletin in the aircraft logs and NO FURTHER ACTION IS 
REQUIRED.  If you believe that the installation may fall within the scope of 
this Service Bulletin please continue with Step 2. 
2. Prepare the aircraft for maintenance. 
3. Remove the KT74 from the aircraft. 
4. Inspect the serial number of the KT74.  If the serial number falls outside the 
range specified in the applicability section or if the serial number is within the 
range but the modification strike off is identified then the transponder can be 
reinstalled.  You may record compliance with this Service Bulletin in the 
aircraft logs and NO FURTHER ACTION IS REQUIRED. 
5. If the transponder installation is within the scope of this Service Bulletin, 
please contact Trig Avionics Limited or a Trig Avionics service centre with 
details of the installation.  Please provide aircraft type, installation location, 
and any supporting installation references, such as Minor Change numbers or 
STC information. 
6. If Trig Avionics confirm that your installation falls within the scope of this 
Service Bulletin they will provide an RMA number and shipping instructions.  
Return the unit as directed for modification.  You may elect to receive a 
Service Exchange unit, or to receive your existing unit with the retaining cam 
replaced. 
7. Modified units will be identified with strike-off 1.  
8. Upon receipt of the updated unit, reinstall it and complete the post installation 
checks in accordance with the KT74 Mode S Transponder Installation 
Manual, P/N 01114-00.

### Page 3

Trig Avionics Limited Service Bulletin  Page 3 of 3 
SUP/KT74/005 Issue 1.0  1 October 2018 
AFM AND PILOT’S MANUAL CONSIDERATIONS  
The pilot operating manual does not require any update and remains revision AC.  
REFERENCES 
KT74 Mode S Transponder Installation Manual, P/N 01114-00-AD. 
KT74 Mode S Transponder Operating Manual, P/N 01115-00-AC. 
MANPOWER 
One hour (1.0 hr) labour for removal and reinstallation. 
WARRANTY 
This service bulletin is warranty reimbursable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
