# True Flight Aerospace Service Bulletin 195: Revision A

- Rights: © True Flight Aerospace. Filed by the FAA in regulations.gov docket FAA-2021-0541; AD 2021-14-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [True Flight Aerospace Service Bulletin 195](https://openairdocs.org/service-documents/true-flight/sb-195.md)
- Title as filed: SB-195A Bondline Inspection
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/55/fb/55fb4612f6584290f099a8158b02a830a5763d200c552caa50fa87d0686c9e43
- Page: https://openairdocs.org/service-documents/true-flight/sb-195/file/55fb4612f658

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

1 | P a g e  
 
2300 Madison Highway Valdosta, GA 31601  
 
SERVICE BULLETIN 
 
CATEGORY 2  
This Service Bulletin contains information pertaining to a threat to the 
continued safe operation of an aircraft or to the safety of persons or property 
on the ground unless some specific action is taken by the aircraft owner.            REVISION 
SB-195 A 
ATA 5521 
DATE:  June 1, 2021 
 
SUBJECT:  Bondline Inspection 
 
MODEL / SERIALS AFFECTED:  AA5, AA-5A and AA-5B  /  All 
 AA1, AA-1A, AA-1B and AA-1C  /  All  
TIME OF COMPLIANCE:    
 
 Perform Part (A) within the next 100 hours, time in service, or the 
next scheduled inspection, whichever occurs first and every Annual 
Inspection thereafter. 
 
 Perform Part (B) once, within the next 25 hours, time in service, or at 
the next scheduled inspection, whichever occurs first.   
  
  
REFERENCE DOCUMENTS:  
 
True Flight Aerospace Service Kit-125B “Flight Controls (ATA No. 27) and Structures (ATA 
No. 51) Bondline Delamination, Repair of” 
 
GENERAL:  All AA1 and AA5 Series Aircraft 
 
All AA1 series and AA5 series aircraft were constructed using a metal-to-metal bonding 
process.  While the bond adhesive has been determined to remain structurally sound throughout 
the aging process, factors such as corrosion and freezing moisture have been found to 
compromise the structural integrity of some of the bond joints.  This can lead to delamination of 
the skin from the wing and stabilizer frames as well as support structure in the fuselage.  
Delamination, left undetected, could result in loss of controlled flight.   
 
Field reports have shown that bondline inspections called out in Chapter 5 of the maintenance 
manual are not being adequately performed during routine inspections.  As these aircraft age 
and have more exposure to the elements, bondline damage due to moisture, ice and corrosion 
are becoming more frequent.  As a result, mechanics must make bondline inspections a primary 
concern during 100 hour/Annual inspections. 
AA-5A, AA-5B 
AA5, AA1, AA-1A, 
AA-1B and AA-1C 
AA5, AA1, AA-1A 
AA-1B and AA-1C

### Page 2

2 | P a g e  
 
This service bulletin provides for the inspection and repair of bondlines.   
             
A.  Required Action:  Bondline Inspection - AA1 series, All - AA5 series, All 
 
1. Carefully inspect all bondlines of the wings, stabilizers and fuselage (Figure 2 & 3) for bondline 
separation using the “Tap Test” method.   With a coin or similar object, tap the length of each 
bondline while listening for a change in tone as the area is traversed.  A bondline separation will 
produce a flat or hollow sound when tapped in the delaminated area. Mark delaminated areas 
with a grease pencil on the outer surface.  (Figure 1) 
2. To verify delamination exists, attempt to insert a 0.004 to 0.006 feeler gauge or another similar 
tool into the bondline. 
3. If no delamination is found, clean all accessible bondlines with MEK, Isopropyl Alcohol or 
Acetone and seal with paint as required.  
4. If any delamination is found, accomplish step C or D of SK-125B as required for repair. 
5. If delamination is found in a horizontal stabilizer of the AA1 series aircraft or the AA5 Traveler, 
comply with B2. 
 
NOTE: 1604-0412 rivets may be substituted for CR3242 -4 - 2 rivets.   
 
6. Inspect the interior of the wings, stabilizers and aft fuselage for corrosion.  If only light surface 
corrosion (white ash appearance) is found, proceed to step (7).  If major corrosion (blisters, 
flaking, cracks or holes in the metal) is found, make repairs as required in accordance with the 
maintenance manual Chapter 20 or install a replacement, serviceable part then proceed to step (7). 
7. If corrosion exists, treat the interior surfaces of the wings, stabilizers and aft fuselage with MIL-
C-81309E (ACF50) or MIL-PRF-81309H (Corrosion X) corrosion inhibitor or equivalent. 
 
NOTE: Remove the wing tips, elevator tips, tail cone and all inspection panels to facilitate 
corrosion treatment.  Use corrosion inhibitor application equipment necessary to reach all 
internal surface areas.  After application, inspect the interior of the aircraft to ensure all 
surfaces have been completely treated.  Repeat corrosion treatment as required. 
 
8. Record compliance in the aircraft log book and note the time for the next inspection. 
 
B. Required Action: Horizontal Stabilizer Inspection - AA1 series, All - AA5 Traveler, All 
 
All AA1 series aircraft and the AA5 Traveler have horizontal stabilizers that are similar in design 
and use the same attachment method for the elevators.  We have received several reports of 
significant delamination of the horizontal stabilizers on these aircraft. This has led to the 
detachment of the outboard elevator attach bracket on one aircraft, resulting in loss of elevator 
control and significant damage to the aircraft.   
 
1. Inspect all bondlines of the horizontal stabilizers as called out in A, 1-4 above (FIGURE 3) with 
emphasis on the outboard rib at the outboard elevator bearing support assembly (FIGURE 4).   
a. Remove the outboard bearing support assembly from the outboard rib of each stabilizer. 
Ref: AA1 or AA5 Series Maintenance Manual Chapter 55.    
b. Inspect the outboard rib in the shaded area for cracks, buckles, corrosion and 
delamination (FIGURE 4).

### Page 3

3 | P a g e  
 
c. Inspect the two MS210471L3K nut plates for security and condition.  Replace if 
corroded or rusty. 
d. If no damage is found, remove paint and surface corrosion from the rib, clean with 
acetone and repaint.  Make sure paint covers the bondlines.   
e. Reinstall the bearing support using new MS24694S53 screws. 
 
2. If any delamination or a previous repair is found on either horizontal stabilizer, accomplish the 
following.   
a. Remove the elevator and the stabilizer as required to gain access to the affected bond 
joints.  Ref: AA1 or AA5 Series Maintenance Manual Chapter 55. 
b. Repair delaminated bond joints in accordance with instructions in SK-125B, D-1 and D-
2. 
c. To protect the integrity of the 301030-501 bearing support assembly attach point, install 
rivets in accordance with SK-125B, D-1 in the top and bottom of the outboard rib and 
rear spar bondlines (Figure 4). 
 
NOTE: 1604-0412 rivets may be substituted for CR3242 -4 - 2 rivets.   
  
CAUTION 
See Figure 5 for rib and spar flange center line location.  When the rivet pattern 
has been established, visually verify that proper distance from the edges of the 
flange is maintained as each hole is drilled.  Hole pattern may need to be modified. 
A rigid ruler or other suitable measuring device may be used as an aid for locating the 
flanges of the center rib and forward spar.  Reference Figure 5. 
i. To locate the forward spar flange, insert a ruler into a lightening hole in the rear 
spar of the stabilizer until it contacts the forward spar web.  Make sure the end of 
the ruler is resting solidly against the spar web and not on a spar lightening hole 
flange and, as close to perpendicular to the spar as possible.  Note the distance 
from the stabilizer trailing edge to the spar web.  Remove the ruler and on the outer 
surface of the stabilizer (at the same location), measure that distance from the 
stabilizer trailing edge forward and mark the location of the spar web.  Repeat this 
process as necessary along the spar to establish a line indicating the forward spar 
flange location.  Mark rivet lines in accordance with SK-125B Figure 3.  
ii. To locate the stabilizer center rib flange, insert a ruler into a lightening hole in the 
inboard end of the stabilizer until it contacts the forward rib. Make sure the end of 
the ruler is resting solidly against the rib web and not on a lightening hole flange 
and, as close to perpendicular to the rib as possible.  Note the distance from the 
stabilizer inboard edge to the rib web.  Remove the ruler and on the outer surface 
of the stabilizer (at the same location), measure that distance from the stabilizer 
inboard edge outward and mark the location of the rib web.  Repeat this process as 
necessary along the rib to establish a line indicating the center rib inboard flange 
location.  Mark rivet lines in accordance with SK-125B Figure 3.

### Page 4

4 | P a g e  
 
 
d. Reinstall the stabilizers if removed and reinstall the elevators. Ref: AA1 or AA5 Series 
Maintenance Manual Chapter 55.  
3. Inspect the interior of the horizontal stabilizers for corrosion.  If only light surface corrosion 
(white ash appearance) is found, proceed to step (4).  If major corrosion (blisters, flaking, cracks 
or holes in the metal) is found, make repairs as required in accordance with the maintenance 
manual Chapter 20 or install a replacement, serviceable part then proceed to step (4). 
4. If corrosion exists, treat the interior surfaces of the stabilizers with MIL-C-81309E (ACF50) or 
MIL-PRF-81309H (Corrosion X) corrosion inhibitor or equivalent. 
 
NOTE: Use corrosion inhibitor application equipment necessary to reach all stabilizer 
internal surface areas.  After application, inspect the interior of the stabilizers to ensure 
all surfaces have been completely treated.   
 
5. Terminating action of Part B of this service bulletin is either of the following: 
a. A finding of all horizontal stabilizer bondlines to be structurally sound. 
b. The repair of all delaminated horizontal stabilizer bondlines plus the installation of rivets 
in the outboard rib and rear spar bondlines in both horizontal stabilizers in accordance 
with B2. 
6. Record compliance in the aircraft log book and notify True Flight Aerospace, LLC of 
compliance. 
 
 
 
True Flight Aerospace, LLC 
2300 Madison Highway  
Valdosta, GA 31601 
Phone: 229-242-6337 
Info@TrueFlightAerospace.com 
 
PART B COMPLIANCE NOTIFICATION: 
 
 
1. Notify True Flight Aerospace, LLC of the following by email at Info@TrueFlightAerospace.com   
Please use the subject “SB-195 Report N*****” and include the following in your message. 
a. Owner 
b. “N” number 
c. Model and year of manufacture 
d. Serial number 
e. Airframe total time 
f. Is Aircraft Regularly covered/hangared? 
g. Condition encountered as a result of SB-195 Part B inspection 
h. Action taken 
 
2. Email is preferred method of notification but if unable please use the Compliance Form  
(SB-195 CFB1) at the end of this document and mail to the address below.

### Page 5 (OCR)

TRUE
FLIGHT
AERDSPACES
COIN
- GREASE PENCIL
IDENTIFIED
BOND JOINT -
- SPOT IN BOND LINE
FIGURE 1
TAP TEST
5 Page

### Page 6

6 | P a g e  
 
 
 
 
NOTE:  AA1 SERIES WINGS 
CARRY FUEL INSIDE THE SPAR.
AFT FUEL TANK BULKHEAD
BONDLINES
FUEL TANK AREA AA5 & AA5A 
WITH STANDARD RANGE FUEL
OUTBOARD WING PANEL 
FOR AA5 SERIES AIRCRAFT
BONDED RIB TO SPAR 
ATTACH COLLARS
LONG RANGE FUEL TANK AREA 
AA5A & AA5B
AA1 SERIES WING
AA5 SERIES INBOARD WING PANEL
 
 
 
 
 
FIGURE 2      
WING BONDLINES

### Page 7

7 | P a g e  
 
BONDLINES
FUSELAGE
AA5 SERIES AIRCRAFT
AA1 SERIES HAS SIMILAR BONDLINES
HONEYCOMB PANELS
AILERON ASSEMBLY: 
AA5, AA5A & AA5B
TRIM TAB
ELEVATOR ASSEMBLY
AA5A & AA5B
HONEYCOMB RIBS
(CANNOT RIVET)
HORIZONTAL STABILIZER 
AA5A & AA5B
RUDDER & VERTICAL STABILIZER
AA5, AA5A AND AA5B
HONEYCOMB RIBS
(CANNOT RIVET)
ELEVATOR AND HORIZONTAL STABILIZER AA1 
SERIES AND AA5
RUDDER AND VERTICAL STABILIZER AA1 SERIES
 
 
 
FIGURE 3 
AA1 SERIES AND AA5 SERIES 
BONDLINES

### Page 8

8 | P a g e  
 
 
ELEVATOR OR 
RUDDER
STABILIZER
STABILIZER
RIVET THESE BOND LINES
301030-501 BEARING 
SUPPORT ASSY.
INSPECT FOR SKIN TO 
RIB DELAMINATION
MS24694S53 SCREW (2)
INSPECT FOR CRACKS IN THIS AREA
FRONT FACE OF 
REAR SPAR
MS21047L3K  
NUT  PLATE (2)
OUTBOARD RIB
TOOLING 
HOLES
OUTBOARD RIB
1604-0412 RIVET (2)
 
 
 
FIGURE 4 
STABILIZER OUTBOARD RIB INSPECTION 
AND RIVET AREA AA1 SERIES & AA5

### Page 9

9 | P a g e  
 
NOTE DISTANCE 
HERE
NOTE DISTANCE 
HERE
NOTE DISTANCE 
HERE
NOTE DISTANCE 
HERE
RULER 
RULER 
RULER 
RIB
CENTER RIB
INBOARD RIB
AFT SPAR
RIB
RIB
SPAR
AFT SPAR
LIGHTENEING HOLES
LIGHTENING HOLES
LIGHTENING HOLES
LIGHTENING HOLES
LIGHTENING HOLES
RULER 
UPPER RIB
FWD SPAR
FWD SPAR
UPPER RIB
 
FIGURE 5 
SAMPLE RULER LOCATIONS, HORIZONTAL AND VERTICAL STABILIZERS

### Page 10

10 | P a g e  
 
 
SB-195 Part B Compliance Notification 
Owner___________________________________________________________________ 
 
“N” Number_______________________________________________________________ 
 
Model_________ Year of Manufacture ___________Serial Number___________________ 
 
Airframe total time____________ Is Aircraft Regularly covered/hangared? _____________ 
 
Condition encountered as a result of SB-195 Part B inspection: 
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________ 
 
 
Mailing Address: 
True Flight Aerospace, LLC 
2300 Madison Highway 
Valdosta, GA 31601 
SB-195 CFB1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
