# Twin Commander Service Bulletin 241: No revision named

- Rights: © Twin Commander. Filed by the FAA in regulations.gov docket FAA-2013-0393; AD 2013-09-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Twin Commander Service Bulletin 241](https://openairdocs.org/service-documents/twin-commander/sb-241.md)
- Title as filed: U.S. DOT/FAA - SB241-IR-SEP-26-2012
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/f7/2e/f72e0fbc19886f6c311fda588ab87b03292d932966e9a9f66b8c618282558e88
- Page: https://openairdocs.org/service-documents/twin-commander/sb-241/file/f72e0fbc1988

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT
THIN
Service Bulletin  COMMANDER  AIRCRAFT LLC
1176 Telecom Drive, Creedmoor, NC. 27522
Tel: (919)-956-4300 • Fax: (919)-682-3786
Service Bulletin 241  September 26, 2012
FUSELAGE ATTACHMENT TO WING MAIN SPAR - INSPECTION & REINFORCEMENT
EFFECTIVITY:  MODELS  SERIAL NUMBERS
690  All (except S/N 11057)
690A  All (except S/N 11104, 11106, 11129, 11134, 11146, 11159, 11173,
11192, 11220, 11237, 11252, 11263, 11280, 11287, 11298, 11303,
11317, 11339 & 11341)
690B  All (except S/N 11383, 11384, 11401 & 11436)
Note: Aircraft serial numbers configured with AVIADESIGN, Inc. STC No. SA5740NM are not compatible with the
modifications contained in SB 241. These aircraft will require FAA approved Alternate Methods of Compliance or
other approved methods to satisfy the structural intent of SB 241.
REASON FOR PUBLICATION:
Aircraft have been found with cracks in the outer fuselage frame attachment to the lower wing main spar at
F.S. 178.81 vertical channel (310384-65 LH & -125 RH). Additional damage has been found at the upper picture
window channel (310704-1 LH & -2 RH), shear clip (310412-23 LH & -24 RH), aft cabin pressure web
(310384-159), external wing to fuselage fillet (110151-33 LH -34 RH) and working or sheared fasteners.
310384-193  F.S.  F.S
CHANNEL  310384-65  178.81
(REF.)  CHANNEL  10736-4!
(REF.)  CLIP (REF.
310736-91 ANGLE
(REF.)
AUP
F.S
MAIN SPAR  126.00
INBD  /D  LOWER CAF  (REF.)  178.81  F.S
31PP (R)
- 14.00,
310704-1 CHANNEL
(REF.)
310384-159
WEB (REF)  FIGURE #1
VIEW LOOKING AFT & OUTBOARD @ LH AFT PRESSURE
BULKHEAD / UPPER PICTURE WINDOW INTERSECTION
RH SIDE OPPOSITE, CABIN INNER FRAME
PANEL SKINS SHOWN REMOVED FOR CLARITY
Page 1 of 20

### Page 2

SERVICE BULLETIN 241 
Page  2  of  20 
COMPLIANCE: 
 
This Service Bulletin contains multiple  initial compliance schedules based on the current airframe hours / time-in-
service.  Part I and II inspections / modifications are required before the expiration of the time period set forth in 
Table A applicable to the airplane; however it is highly recommended that Part I & II , inspections / modifications 
be accomplished at the earliest practicable time. 
 
INITIAL COMPLIANCE SCHEDULE 
CURRENT AIRFRAME 
(HOURS / TIME-IN-SERVICE) 
COMPLIANCE REQUIRED PRIOR TO (HOURS / TIS) 
OR WITHIN THE NEXT [MONTHS] WHICHEVER COMES FIRST
0000 - 2000 
2001 - 3000 
3001 - 4000 
4001 - 5000 
5001 - 6000 
6001 - 7000 
Over 7000 
(1000) Hours  or  [36] Months 
(800) Hours  or  [36] Months 
(650) Hours  or  [33] Months 
(500) Hours  or  [30] Months 
(350) Hours  or  [24] Months 
(250) Hours  or  [18] Months 
(150) Hours  or  [12] Months 
-  Table A  - 
 
 
Part I: ACCESS, DISASSEMBLY & INSPECTION OF  THE FUSELAGE TO WING MAIN SPAR 
ATTACHMENT JOINTS 
 
Part I, Access, Disassembly & Inspections are accomplish ed to record material discrepancies (damage) in the 
fuselage to wing attachment area.  Due to amount of  man hours required to accomplish Part I, Part II is 
Mandatory.  This will eliminate the requirement for futu re reoccurring inspections.  The reinforcements designed 
and installed per this bulletin are terminating action. 
 
 
Part II: MODIFICATION AND REASSEMBLY OF THE FU SELAGE TO WING MAIN SPAR ATTACHMENT 
JOINTS 
 
This modification removes all the damaged or potential dama ged sheet metal parts in the area of the fuselage to 
wing main spar joint.  This modification primarily replac es joint parts with improved heavier machined parts.  The 
modification cuts and removes the upper 18.5-inc h section of the existing 310384-65/-125 channels and 
incorporates a heavier gage extruded channel as a replacement.  The extruded channel was designed to nest 
into the lower remaining section of the existing channel.  A vertical strap is cradled into the new frames making 
the joint Failsafe and provides improved fastener edge distan ce.  Parts are being replaced for safety of flight to 
repair damage, prevent future damage and improve load paths. 
 
 
 
BY WHOM WORK WILL BE ACCOMPLISHED: 
 
A & P Mechanic (or Equivalent), and an ASNT Level II or III Certified NDT Inspector (or Equivalent) per 
INSPECTION REQUIREMENTS. 
 
Due to the complexity of the work and potential to  damage existing fuselage and wing structure during 
completion of the modification, it is mandatory that  at least one member of the team accomplishing this 
task complete Twin Commander Aircraft approved training.  Such training is available at the Factory 
Authorized Maintenance Training Provider. 
 
NOTE: 
IT IS RECOMMENDED THAT ALL MODIFI CATIONS BE COMPLETED ONLY AT AN 
AUTHORIZED TWIN COMMANDER SERVICE CENTER.

### Page 3

SERVICE BULLETIN 241 
Page  3  of  20 
APPROVAL: 
 
Modifications described by this Service Bulletin are FAA DER Approved. 
 
 
 
RELATED PUBLICATIONS: 
 
SB 164 “INSPECTION AND REPLACEMENT OF WING SPAR FILLET SCREWS”.  SB 241 incorporates 
applicable portions of the changes defined per SB 164. 
 
SB 164 EFFECTIVITY:  MODELS 690 (S/N 110 00 – 11079, except 11011, 11014, 11021, 11028, 
11035, 11041, 11042, 11046, 11058, 11060, 11065, 11069 & 
11074) 
690A (S/N 11100 – 11344, except  11103, 11105, 11111, 11128, 
11134, 11135, 11141, 11155, 11169, 11170, 11173, 11184, 
11188, 11196, 11199, 11207, 11214, 11218, 11220, 11231, 
11257, 11274, 11277, 11281, 11288, 11291, 11298, 11305, 
11318, 11323, 11325 & 11329) 
690B (S/N 11350 – 11566, exc ept 11338, 11355, 11366, 11406 
& subs.) 
 
SB 208A “INSPECTION FOR WING MAIN SPAR LOWER CAP CORROSION”.  Highly recommend SB 208A and 
SB 241 be accomplished at the same time to reduce man hours .  Both Service Bulletins require fuel cells and fuel 
cell liners are removed from the center wing fuel tanks. 
 
SB 223 “WING LEADING EDGE ATTACHMENT INSPECTION AND MODIFICATION”.  Recommend SB 223 and 
SB 241 are accomplished at the same time interval. 
 
CK-144 “LOWER SPAR CAP REPLACEMENT PROCEDURE”.  Highly recommend CK-144 per SB 208A, and SB 
241 be accomplished at the same time interval to reduce overall man hours if deemed necessary.  The wing lower 
main spar cap, replaced per SB 208A (CK-144), have fasteners that are common to both SB 208A and SB 241.  
Both Service Bulletins require fuel cells and fuel cell liners are removed from the center wing fuel tanks. 
 
SI-255 “PICTURE WINDOW UPPER CHAN NEL INSPECTION”.  Aircraft previous ly configured with the improved 
310704-3/-4 channels will not require replacement per SB 241. 
 
SL-382 “SEALING CABIN LEAKS IN AIRCRAFT PRESS URIZED TO THE FLOOR”.  Recommend SL-382 and 
SB 241 are accomplished at the same time interval. 
 
 
 
ESTIMATED MAN HOURS:  (Per Side - For Access, Inspection, Modification and Assembly) 
 
Part I: 
Access, Disassembly & Inspections      LH Side  92  HRS 
          R H  S i d e  92  HRS 
Part II: 
Modification & Reassembly       LH Side  200  HRS 
          R H  S i d e  200  HRS 
 
Parts required to comply with this Service Bulletin may be purchased through any TWIN COMMANDER 
FACTORY-AUTHORIZED SERVICE CENTER.  Indicate SB 241, aircraft model and factory serial number when 
submitting order.

### Page 4

SERVICE BULLETIN 241 
Page  4  of  20 
PARTS DATA: 
 
KIT  SB241 
 
Qty Part Number Description 
1 K310384 (DWG) AFT PRESS. BLKHD - WING SPAR FRAME ATTACH REINFORCEMENT 
1 310364-3 CHANNEL  K310384-501 INSTL, LH 
1 310364-4 CHANNEL K310384-502 INSTL, RH 
1 310364-5 STRAP K310384-501 INSTL, LH 
1 310364-6 STRAP K310384-502 INSTL, RH 
1 310364-7 TEE K310384-501 INSTL, LH 
1 310364-8 TEE K310384-502 INSTL, RH 
1 310364-9 STRAP K310384-501 INSTL, LH 
1 310364-10 STRAP K310384-502 INSTL, RH 
2 310364-11 WEB K310384-501/-502 INSTL, L & RH 
1 310704-3 CHANNEL K310384-501 INSTL, LH 
1 310704-4 CHANNEL K310384-502 INSTL, RH 
1 310736-45 CLIP K310384-501 INSTL, LH 
1 310736-46 CLIP K310384-502 INSTL, RH 
12 170468-5 SHIM K310384 (USE AS REQD.) 
---------- -------------------------- -------------------------------- -------------------------------------------------------- ------- 
2 310364-13 FILLER K310384-503/-504 INSTL, L & RH 
2 310364-15 FILLER K310384-503/-504 INSTL, L & RH 
1 310364-17 ANGLE K310384-503 INSTL, LH 
1 310364-18 ANGLE K310384-504 INSTL, RH 
2 310364-19 STRAP K310384-503/-504 INSTL, L & RH 
---------- -------------------------- -------------------------------- -------------------------------------------------------- ------- 
1 310364-21 DOUBLER K310384-505 INSTL, LH 
1 310364-22 DOUBLER K310384-506 INSTL, RH 
2 310364-23 ANGLE K310384-505/-506 INSTL, L & RH 
1 310364-25 DOOR K310384-505 INSTL, LH 
1 310364-26 DOOR K310384-506 INSTL, RH 
---------- -------------------------- -------------------------------- -------------------------------------------------------- ------- 
ALL PER DWG HARDWARE 
 
TO BE PROCURED LOCALLY:  (as required) 
 
1.  MS20426AD4, AD5 & AD6 (BB) type rivets  and MS20470AD4, AD5 & AD6 (BJ) type rivets. 
2.  NAS1097AD5 & AD6 (LZ) type rivets. 
3.  NAS1097E5 or KE5 type rivets. 
4.  CR3242-4 & -5 (ARD) type rivets  and CR3243-4 & -5 (ARE) type rivets. 
5.  Epoxy primer used for touch up on parts furnished wi th the factory Modification Kits per MIL-PRF-23377, Type 
I, Class C. 
6.  PR-1440-C20 or PR O SEAL 890-C20 sealant per MIL-S-8802 / AMS-S-8802. 
7.  PolyGone 300-AG Gel (Aviation Grade Polysulfide Em ulsifier).  High performance gel form designed to 
remove polysulfide and other sealants from a variety of surfaces.  Follow manufactures recommendations for 
applicable uses of this product 
8.  Nashua 345, 3M 474 or Polyken 231, prem ium grade tape per ASTM D-5486 Type IV, Class 1. 
 
CAUTION: 
THE SUBSTITUTION OF BLIND RIVETS OTHER THAN THOSE INDICATED ON TWIN COMMANDER 
DWG NO. K310384 IN THE GENERAL NOTES OR ON THE FIELD OF DRAWING IS NOT PERMITTED 
WITHOUT AUTHORIZATION FROM THE AIRFRAME MANUFACTURE OR APPROVED BY A 
REPRESENTATIVE OF THE FAA.

### Page 5

SERVICE BULLETIN 241 
Page  5  of  20 
RECOMMENDED TOOLS: 
 
1.  GO-NO-GO gages for HI-LOK fastener inspection. 
2.  Sheet metal tools needed for difficult access areas. 
3.  Cherry 269C3 selector gage for determining materi al thickness for installation of blind fasteners. 
4.  Cratex rub bloc k stick for cleaning and polishing fastener holes and metal surfaces. 
 
 
 
SPECIAL TOOLS: 
 
None 
 
 
 
GENERAL INSPECTION CRITERIA: 
 
TYPES OF INSPECTION FOUND IN THIS SERVICE BULLETIN ARE PER AC 43.13-1B CHAPTER 5 
“NONDESTRUCTIVE INSPECTION” (NDI). 
 
 Perform FLUORESCENT DYE PENETRANT  structural inspection as an aid in disclosing crack 
indications or other failures not detectable by visual means.  Carefully remove sealant and / or finishes as 
necessary in order to allow inspection of the structural elements.  Moderate hand pressure applied 
between parts, in order to produce any relative movement  allowed, may assist in detection of failure of 
parts or joining fasteners.  Also observe any rub marks indicating relative movement of parts under load. 
 
 Perform EDDY CURRENT structural inspection as an aid in disclosing subsurface crack indications or 
other failures not detectable by dye penetrant means.   Fastener holes must be properly reamed before 
completing eddy current inspections, otherwise false results might be obtained. 
 
 
Areas to be inspected are identified by Part Number and / or Name and are located per the applicable 
INSPECTION FIGURE(S). 
 
NOTE: 
ILLUSTRATED PARTS CATALOG MA Y BE USED FOR ASSISTANCE  IN LOCATING INSPECTION 
AREAS (REFERENCE ONLY).  INSPECTIONS A PPLY TO LEFT AND RIGHT HAND SIDES UNLESS 
OTHERWISE INDICATED.  ONLY THE ODD NUMB ER PARTS AND ASSEMBLIES ARE REFERED TO 
IN THE FOLLOWING TEXT.  EVEN NUMBERS ARE EQUAL APPLICABLE OPPOSITE PARTS.

### Page 6

SERVICE BULLETIN 241 
Page  6  of  20 
INSPECTION REQUIREMENTS: 
 
1. PERSONNEL QUALIFICATION 
 
a. NDI Level II or Level III. 
b. Shall be qualified and certified in accordance wi th ASNT Personnel Qualifications SNT-TC-1A, 
ANSI / ASNT CP-189, NAS 410, or MIL-STD-410. 
  
2. MATERIALS AND EQUIPMENT 
 
a. Only materials listed or approved for listing per document QPL-AMS 2644 or QPL-25135             
(Qualified Products List) shall be used for penetrant inspections.  Cleaner, Penetrant and Developer to be 
from the same product manufacturer. 
b. Solvent Removable Fluorescent Penetrant, per ASTM-E1417 or SAE-AMS 2644 sp ecifications, latest 
revision. 
c. Solvent Remover (Class 1), per ASTM-E1417 or  SAE-AMS 2644 specifications, latest revision. 
d. Nonaqueous Develo per (Form D), per ASTM-E1417 or SAE-AMS 2644 specifications, latest revision. 
e. Black Lights used for viewing & inspection must me et ASTM-E1417 specifications, calibrated per ANSI / 
NCSL Z540-1 or ISO 10012-1. 
f. Inspection mirror. 
 
3. CLASSIFICATION 
 
 a. Per ASTM-E1417 or SAE-AMS 2644 sp ecifications, latest revision. 
b.  Type 1 (Fluorescent Dye), Method C (Solv ent Removable), Sensitivity Level 3 (High). 
c.  Twin Commander Process Specification 130.17 “Eddy Cu rrent Flaw Detection in Aluminum Alloys”, latest 
revision.

### Page 7

SERVICE BULLETIN 241 
Page  7  of  20 
Part I - ACCESS, DISASSEMBLY & INSPECTIONS: 
 
See the appropriate section of the airplane maintenance manual for procedures and instructions on removing and 
re-installing applicable items listed below. 
 
1. Disconnect batteries. 
 
2. De-fuel the airplane. 
 
3. Shore the airplane at the wing jack pad (Item ) and tail tie down stand (Item ) per FIGURE #2 and level 
per Maintenance Manual instructions. 
 
 
 
4. Complete shoring and leveling procedures as outlined per FIGURE #2 for (items &) to prevent movement 
of the fuselage and wing structure. 
 
5. Remove the cabin interior (seating, side panels and head liner) components from (F.S. 126.00) aft to the 
pressure bulkhead web assembly located at (F.S. 178.81). 
 
a. Take necessary measures required to protect elec trical and air-conditioning equipment on aft pressure 
bulkhead. 
 
b. Protect and remove the left and right hand cabin picture window assemblies.

### Page 8

SERVICE BULLETIN 241 
Page  8  of  20 
Part I - ACCESS, DISASSEMBLY & INSPECTIONS:  (continued) 
 
6. Baggage compartment area (Center Wing Fuel Tanks): 
 
a. Remove the baggage compartment forward and upper interior closeout panels as necessary to gain 
access to the aft side of the aft pressure bulkhead assembly and center wing fuel tanks. 
 
b. Disconnect the center wing fuel tank fittings and sump.  Unbolt the lower fuel tank removable floor 
structure.  Remove the lower fuel  tank cell.  Optional to remove the aft and outboard lower fuel tank 
panels. 
 
c. Remove the lower wing skin access door to gain ac cess to the center wing upper fuel tank.  Disconnect 
and remove the upper fuel tank cell. 
 
d. To gain access to the aft side of the wing main spar  cap, remove the upper fuel tank liner panels.  This 
will also allow access to fasteners being replaced common to the lower wing drag channel located inboard 
of W.S. 24.07. 
 
e. Refer to K310384, Section G-G.  Drill and remove t he six (per side) existing rivets attaching the lower 
wing skins to the lower wing drag channel. 
 
CAUTION: 
EXERCISE CAUTION WHEN REMOVING FASTENERS, DO NOT DRILL INTO THE MAIN SPAR 
LOWER CAP. 
 
f. Remove and cleanup any old residual sealant and tape from the aft side of the main spar cap web 
assembly from (W.L. -1.64 to W.L. -12.18) and from (L.B.L. 15.00 & R.B.L. 15.00 outboard). 
 
CAUTION: 
AVOID THE USE OF TOOLS WHICH MAY CUT OR SCRATCH ALUMINUM SURFACES. 
 
7. Inboard wing area (directl y outboard of W.S. 24.07): 
 
a. Remove the upper wing fuel tank access doors (f orward and aft) of the main spar cap assembly. 
 
b. Disconnect the inboard wing fuel tank fittings and re move or push back the fuel tank bladders to gain 
adequate access to the outboard side of the W.S. 24.07 rib. 
 
c. Refer to K310384, Section G-G and Figure #3.  Drill and remove the existing rivets attaching the lower 
wing to fuselage fillets fore and aft of F.S. 178.  Caution:  Do not remove existing rivets common to the 
W.S. 24.07 rib lower return flange (inboard flush row under fillet). 
 
NOTE: 
SOME AIRCRAFT MAY HAVE PRIOR INSTALLED REPAIRS OVER THE EXI STING LOWER WING 
TO FUSELAGE FILLET ANGLES.  PRIOR REPAIRS MUST BE EVALUATED FOR THE AFFECTS ON 
COMPLIANCE WITH THIS SERVICE BULLETIN.  CONTACT TWIN COMMANDER AIRCRAFT IN THE 
EVENT PRIOR REPAIR WILL NOT BE COMPLETELY REMOVED BY THIS BULLETIN. 
 
d. Remove the four screws / Huck bolts common to the lower wing to fuselage fillet and main spar lower cap 
outboard of W.S. 24.07.  If the aircraft has complied with SB 164, these fasteners may have already been 
changed.  The original production version was MS27039 screws.  These four (per side) existing fasteners 
must be removed to allow for additional modification parts.

### Page 9 (OCR)

SERVICE BULLETIN 241
Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
e. Eddy Current inspect the existing fastener holes common to the main spar lower cap forward and aft
flange per FIGURE #3. Prior to Eddy Current inspection, existing holes must be within limits indicated per
Dwg No. K310384, General Note #8. Identify and record any damage found on the SB 241
Compliance Card. Provide photographs of the damage.
†.  Fluorescent Dye Penetrant inspect the 110151-33 fillet radius 4.0-inch fore / aft of F.S. 178.81 per
FIGURE #3 for crack indications. Note: Stop drill extreme ends of cracks with #40 drill (0.098 dia.) and
rout along the fore / aft length of crack (0.098 dia.) after completion of Part I, Item #11. Stop drill holes
and routed areas must maintain a minimum of 2 X fastener diameter (edge distance) from the center of
existing fastener hole locations. If measured crack lengths are within limits, it is acceptable to proceed
with the modifications per Dwg No. K310384-503 instl. If crack lengths exceed limits indicated or edge
distance is below minimums, part must be removed and replaced with a new part or an approved repair
must be installed prior to return to service. Identity and record any damage found on the SB 241
MAXIMUM ALLOWABLE CRACK LENGTH
INSPECT FOR CRACKS  1.50-INCH EXTENDING FROM THE
ALONG FILLET RADIUS  PT  EXISTING FASTENER HOLE LOCATIONS
ITEM #7, f.  6.00-INCH MAXIMUM OVERALL
INSPECT MAIN SPAR LOWER CAP  FWD / AFT FLANGE BOLT HOLES  EC  6.00  (SEPARATE OR COMBINED LENGTH)
FOR CRACKS (4 PLCS)  MAX.
1.50
ITEM #7, e.  MAX.  1.50
MAX.  LOWER WING
SKIN (REF.)
ITEM #7, c.
•
ITEM #7, d
110151-33/-34
FILLET (REF.)
FUSELAGE SIDE  F.S.  STOP DRILL EXTREME CRACK ENDS AND ROUT
SKIN (REF.)  178.81  CRACK LINE SMOOTH BETWEEN STOP DRILLS
WITH A #40 DRILL (0.098 DIA.). PROTECT BACKUP
UP  FIGURE #3  STRUCTURE WITH STAINLESS STEEL SHIM STOCK  BEFORE DRILLING OR ROUTING
VIEW LOOKING UP & INBOARD @
FWD  LH LOWER WING TO FUSELAGE FILLET
8. Aft fuselage compartment area (Picture Window):
a. Refer to K310384, Section A-A. Drill and remove the cabin inner skin structural panels and reinforcement
gussets above the cabin picture window from F.S. 126.00 to F.S. 171.36.
CAUTION:
EXERCISE EXTREME CARE WHEN DRILLING I REMOVING EXISTING FASTENERS. DO NOT
OVERSIZE OR DOUBLE DRILL EXISTING HOLES IN ATTACHING STRUCTURE.
b. Refer to K310384, Section A-A. Drill and remove the cabin inner skin structural panels and reinforcement
gussets aft of the cabin picture window from (F.S. 172.50 to F.S. 178.81) from (W.L. -8.00 to W.L. -35.25).
NOTE:
THE CABIN FLOOR IS AT W.L. -55.50.
Page 9 of 20

### Page 10

SERVICE BULLETIN 241 
Page  10  of  20 
Part I - ACCESS, DISASSEMBLY & INSPECTIONS:  (continued) 
 
NOTE: 
IF ANY OF THE CABIN INNER SKIN STRUCTURAL PANELS HAVE BEEN MODIFIED WITH 
ADDITIONAL ACCESS HOLES OT HER THAN THE FACTORY RET URN FLANGED PARTS, THEY 
MUST BE REMOVED AND REPLACED WITH NEW PA RTS OR AN APPROVED  REPAIR MUST BE 
INSTALLED PRIOR TO RETURN TO SERVICE. 
 
9. Refer to K310384, Section A-A.  Remove the 310704-1 channel by removing the fastener row common to the 
lower wing to fuselage fillet from F.S. 126.00 to F.S. 178. 81.  Remove the shear clips that attach the channel 
to the frames. 
 
NOTE: 
IF THE EXISTING 310704-1 UPPER PICTURE WI NDOW CHANNEL HAS BEEN PRIOR REMOVED 
AND REPLACED WITH THE IMPR OVED 310704-3 CHANNEL, THEY MAY BE LEFT IN PLACE WITH 
THE OPTION TO REMOVE AND REINSTALL. 
 
a. Partial removal of the right side upper fuselage ice sh ield is required to access  existing flush skin rivets 
attaching the upper picture window channel. 
 
b. After removal of the existing picture window channels from the aircraft, remove and cleanup any old 
residual sealant left in place that may interfere with the new channel replacement. 
 
c. Fluorescent Dye Penetra nt inspect the removed channels outboard flange, radius and web – complete 
length - for damage.  Cracks have been found along t he outboard return flange (rivet hole to rivet hole) 
and along the parts lower web at areas common to the stub frame shear clip outboard attachment 
fasteners.  Identify and record any damage found on the SB 241 Compliance Card.  Provide 
photographs of the damage. 
 
10. Refer to Figure 1.  Remove the two horizontal pin and collar type fasteners attaching the 310412-23 shear 
clips.  Note: During removal of these fasteners, inspect each fasteners pin / collar for working, tension or 
shear type damage.  Identify and record any damage found on the SB 241 Compliance Card.  Provide 
photographs of the damage. 
 
11. Removal of the 310384-65/-125 channels and upper 310384-159 web.  
 
a. Refer to K310384-501.  Remove remaining fastener s (including the two .250-inch diameter bolts common 
to the upper and lower wing main spar caps) attaching the 310384-65/-125 channels web. 
 
b. Refer to. K310384 Sect E-E.  Remove fasteners from outboard fuselage skin below the wing to W.L.         
-28.00.  Remove and retain the shear clip attaching the existing lower picture window channel.  Note: The 
W.L. -28.00 clip will be reinstalled later. 
 
c. Refer to Figure 1.  Remove and discard the 310736-45 shear clip attaching the upper picture window 
bulbed angle at W.L. -8.00 to the inboard flange leg of the 310384-65/-125 channels. 
 
d. Refer to K310384-501.  Remove fasteners (including the two .250-inch diameter bolts common to the 
upper and lower wing main spar caps) attaching the 310384-193 channels from (W.L. -1.64 to W.L.           
-28.00).  Remove all fasteners between the two vert ical wing support channels.  Remove fasteners 
common to the lower fuel tank suppo rt structure and field fasteners attaching the 310384-159 web to the 
aft pressure bulkhead from (W.L. -1.64 to W.L. -28.00). 
 
e. Refer to K310384-501.  Determine the cut line (W.L -25.8 & L.B.L. 16.4) for the 310384-159 web.  Insert 
stainless steel shim stock on the aft side of the 310384-159 web and aft attaching structure before cutting.  
Cut and remove the indicated section of 310384-159 web and remove.

### Page 11 (OCR)

SERVICE BULLETIN 241
Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
Refer to K310384-501. Fluorescent Dye Penetrant inspect the 310384-159 web outboard edge between
(W.L. -10.0 to W.L. -12.18) for damage. Identify and record any damage found on the SB 241
Compliance Card. Provide photographs of the damage.
g. Refer to K310384-501. Determine the approximate cut line (W.L -20.15 +/- .10) for the 310384-65/-125
channels. This location may vary slightly depending on the original fasteners location. Maintain a
minimum of .36-inch edge distance from the channel cut line to the center of existing fastener hole
locations. If necessary, the cut may be slightly angled to maintain these minimums. Additional material
has been left on the replacement 310364-3 channels upper and lower ends to allow for vertical
adjustment while locating the new parts.
h. Refer to K310384-501. After the cut locations have been marked, insert stainless steel shim stock on the
outboard side (between the 310384-65/-125 channel and fuselage skin). Cut and remove the upper
section of the -65/-125 channels.
i. Fluorescent Dye Penetrant inspect the removed 310384-65/-125 channels outboard flange, radius and
web 4.0-inch above and below W.L. -12.18 for damage. Identify and record any damage found on the
SB 241 Compliance Card. Provide photographs of the damage.
12. Main spar lower cap forward flange radius and upper and lower main spar .250-inch diameter bolt holes
inspection:
a. Refer to Figure #4. Remove residual sealant from the local area (W.S. 24.07 / W.L. -12.18) to allow the
radius of the spar forward flange to be cleaned and polished to a 32 RMS finish.
b. Fluorescent Dye Penetrant inspect .50-inch radius along the cutout of the forward flange at W.S. 24.07 on
the main spar lower cap.
INSPECT MAIN SPAR UPPER & LOWER CAP  INSPECT MAIN SPAR LOWER
VERTICAL FLANGE AND SPAR WEB BOLT  CAP FORWARD FLANGE .50-INCH
HOLES FOR CRACKS (4 PLCS)  RADIUS FOR CRACKS
ITEM #12, f.  ITEM #12, b.
MAIN SPAR WEB
(REF.)
W.S. 24.07 RIB
(REF.)
MAIN SPAR LOWER
CAP (REF.)  - 110151-33
FILLET (REF.)
W.L  W.S.
-12.18  24.07
FUSELAGE SIDE
310420-9 CHANNEL  - 310420-13 CLIP  SKIN (REF.)
\ UP  (REF.)  (REF.)
FIGURE #4
VIEW LOOKING AFT & OUTBOARD @ LH
INBD  FWD  FUSELAGE F.S. 178.81 / W.L. -12.18 / W.S. 24.07
VIEW SHOWN WITH 310384-65 CHANNEL, -159 WEB
& 310704-1 UPPER PICTURE WINDOW CHANNEL REMOVED
Page 11 of 20

### Page 12

SERVICE BULLETIN 241 
Page  12  of  20 
Part I - ACCESS, DISASSEMBLY & INSPECTIONS:  (continued) 
 
c. Refer to K310384 Section L-L.  If a crack is detect ed in the main spar lower cap radius, contact Twin 
Commander Aircraft LLC.  Aircraft is not to continue in  service.  If no cracks are found, check the main 
spar lower cap radius to be certain that machined transition area of the forward flange has a minimum 
radius of .50-inch and surface finish 32RMS or better.   In addition, the lower main spar steel strap (.032-
inch thick) also follows th is .50-inch radius trim common to the fo rward flange.  Ensure the steel straps 
edge is flush with the spar radius trim.  If the straps edge is not flush with the forward flange radius, trim 
flush with spar radius and provide surface finish 32 RMS or better at this location. 
 
d. If the inspection reveals any deviation (except cracki ng), proceed as follows.  Provide surface finish 
32RMS or better to any rough areas, notches or machine marks in the radius area while maintaining a 
minimum radius of .50-inch and a surface finish of 32 RMS. 
 
CAUTION: 
MAINTAIN 2D EDGE DISTANCE ON ALL FASTENERS.  DO NOT CUT INTO THE VERTICAL LEG OF 
THE MAIN SPAR LOWER CAP. 
 
e. After the main spar lower cap radius has been inspected, restore sealant and finishes.  Identify and 
record any damage found on the SB 241 Compliance Card.  Provide photographs of the damage. 
 
NOTE 
PRIOR TO EDDY CURRENT INSPEC TION OF EXISTING .250-INCH DIAMETER MAIN SPAR UPPER 
AND LOWER CAP HOLES, MUST REAMED WITHIN (.2659 /.2648 DIA). 
 
f. Fluorescent Dye Penetrant inspect .250-inch diameter  holes in the upper and lower main spar caps for 
cracks per FIGURE #4.  If a crack is detected, contact Twin Co mmander Aircraft LLC.  Aircraft is not to 
continue in service.  Identify and record any damage found on the SB 241 Compliance Card. 
 
13. Corrosion preventative measures an d sealants must be restored after inspections are completed.  See part II, 
Item 12. NOTE. 
 
14. Fill out information on the SB 241 Compliance Card and send to: 
 
Twin Commander Aircraft LLC 
Attn.:  Service Department 
1176 Telecom Drive 
Creedmoor,  NC.  27522 
 
15. Part I, access, disassembly & inspections complete.

### Page 13

SERVICE BULLETIN 241 
Page  13  of  20 
Part II - MODIFICATION & REASSEMBLY: 
 
1. Baggage compartment area (Wing Drag Channel): 
 
a. Refer to K310384 Section G-G.  Install six (per si de) HL20PB-5 Hi-Lok fasteners.  These Hi-Loks replace 
six removed solid fasteners per (Part I, Item #6, e).  Fasteners attach the lower wing skin to the 310420-9 
wing drag brace channel.  Remove and replace any additional working or damaged fasteners in the area 
with the same type and size removed. 
 
2. Inboard wing area (Wing to Fuselage Fillet): 
 
a. Refer to K310384-503.  Position, drill and install the 310364-13 filler, -15 filler, -17 angle and -19 strap.  
Additional material has been left on these parts to allow trimming upon installation.  The total fastener 
count per -503 instl to be maintained.  Note:  Any damage to the existing lower fuselage fillet radius to be 
stop drilled and routed out per Figure 3, before reinforcement parts are installed. 
 
b. Install clecos as required, to po sition parts.  Only install fasteners along the outbd flange of the added fillet 
angle (-17) at this time, due to sequencing (see sect F-F).  Refer to Dwg No. K310384, General Note #8 
for applicable fasteners attaching through the main spar lower cap forward and aft flanges.  Refer to Dwg 
No. K310384, General Note #2 for application of sealant. 
 
c. Ensure the modification parts and sealant does not cover or plug the lower wing skin drain holes. 
 
d. Only install fasteners in the vert ical flange of the added fillet angles located aft of F.S. 178.81.  Do not 
install the existing fastener locat ed in the F.S. 178.81 frame line / skin lap or any fastener forward other 
than with clecos at this time.  These fasteners to be coordinated with the following item 7.e. 
 
e. Refer to Dwg No. K310384, General Note 6 for application of sealant. 
 
3. Fuselage to Wing Joint Area (Upper/ Outer Frame and Pressure Web Mod): 
 
a. Refer to K310384-501.  Position the 310364-11 web in place.  It will be necessary to drill out and remove 
three to four fasteners below W.L. -28.00 attaching the existing 310384-65/-125 & -193 channels to the aft 
pressure bulkhead web to allow the -11 web to be positioned.  Remove the existing bulbed tee angle 
installed at L.B.L. 11.7 (extends from the upper to lowe r main spar caps) if required, to install the 310364-
11 web.  Reinstall bulbed tee with same type and size  fasteners as removed or acceptable to substitute 
fasteners per Dwg No. K310384, General Note #10.  Additional material has been left on the upper, lower 
and inboard ends of the -11 web to allow trimming as necessary for adjustment based on existing fastener 
locations.  The total fastener count as shown on Dwg No. K310384-501 instl to be maintained. 
 
b. After the -11 web has been trimmed and placed in to position, match drill existing fastener locations along 
the length of the 310384-193 channel  and support with Clecos.  Note:  Additional added fasteners have 
been inter spaced between existing locations comm on to the 310384-193 channel between (W.L. -12.18 
to W.L. -27.6).  This provides a double fastener row along the inboard splice edge of the -11 web.  Double 
fastener row is also between (W.L. -25.8 to W.L. -27.6). 
 
NOTE: 
TO PREVENT A GAP BETWEEN PARTS AND FAST ENER PRELOAD, INSTALL 170468-5 SHIMS 
(TRIM AS NECESSARY) OR FABRICATE TAPERED ALUMINUM SHIMS ON THE ENDS OF PART 
TRANSITIONS AS INDICATED PER DWG NO. K310384, GENERAL NOTE #4

### Page 14

SERVICE BULLETIN 241 
Page  14  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
c. Refer to K310384-501.  Position the 310364-3 cha nnel on the forward side of  the 310384-65 channel 
which was prior cut at approximately W.L. -20.15.  The -3 channel has been machined down to nest into 
the lower remaining section of the 310365-65 channel a pproximately 5.6-inches to form a lap splice for 
the frame directly above W.L. -25.8.  Additional material has been left on the upper and lower ends of the 
-3 channel to allow trimming as necessary for fastener adjustment. 
 
CAUTION: 
ONLY SLIGHT TO MODERATE HAND PRESSURE SHOU LD BE EXERTED TO NEST THE LOWER 
END OF THE 310364-3 CHANNEL INTO THE UPPER  TRIMMED END OF THE EXISTING 310384-65 
CHANNEL.  DO NOT FORCE -3 CHANNEL INTO  POSITION BY PRELOADING EXISTING -65 
CHANNEL.  IF INTERFERENCE OCCURS, CONTACT TWIN COMMANDER AIRCRAFT LLC FOR 
DISPOSITION. 
 
d. Position the 310364-5 strap into the 310364-3 channel  from (W.L. -1.64 to W.L. -23.95).  The upper 
existing fastener hole location (HL64PB-8) to mainta in.50-inch minimum edge distance on the -5 strap 
upper machined end.  The lower machined end to be located at an existing #5 rivet hole.  Maintain a 
minimum edge distance of .36-inch.  Additional material has been left on the upper and lower ends of the 
-5 strap to allow trimming as necessary for adjustment based on existing fastener locations. 
 
CAUTION: 
BEFORE INSTALLING THE 3103 64-3 CHANNEL VERIFY THE CLEA RANCE BETWEEN THE MAIN 
SPAR LOWER CAP FORWARD FLANGE .50-INCH RADIUS AND THE OUTBOARD FLANGE RADIUS 
OF THE REPLACEMENT 310364-3 CHANNEL (SEE FIGURE 4).  INSERT FEELER GAGES INTO THE 
JOINT TO ENSURE A MINIMUM CLEARANCE OF .032-INCH.  (REFER TO DWG NO. K310384, 
SHEET 2 OF 4, SECTION L-L).  OPTIONAL TO USE A RAPID CURE HARDENING PUTTY THAT MAY 
BE REMOVED AND MEASURED TO DETERMINE CLEARANCE.  CHECK FOR PRELOAD IN ALL 
MATING PARTS.  DO NOT FORCE PARTS, USE FLAT OR TAPERED ALUMINUM SHIMS PER 
K310384 NOTE 4. 
 
e. Refer to K310384-501.  Match drill -3 channel and -5 strap to existing fastener holes where applicable. 
 
4. Upper picture window channel area: 
 
a. Refer to K310384, Section B-B.  Position the 310704-3 channel replacement above the picture window 
from (F.S. 126.00 to F.S. 178.81).  Note:  If necessary, trim aft end of 310704-3 channel to clear forward 
flange legs of 310364-3 channel, maintaining .050-inch clearance. 
 
b. Match drill the 310704-3 channel to the existing sh ear clip attachment fasteners between (F.S. 126.00 
through F.S. 172.50). Match drill along the outboard flange leg attaching to the outer fuselage side skin 
and Cleco into position.  Refer to Dwg No. K310384, General Note #15 for additional installation 
instructions and limitations regarding the 310704-3 channel.

### Page 15

SERVICE BULLETIN 241 
Page  15  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
5. Machined tee clip instl (Forward si de of F.S. 178.81 & W.L. -14.00) area: 
 
a. Refer to K310384-Section A-A, B-B,& C-C.  Position  the 310364-7 tee with the forward horizontal flange 
leg against the lower side of the 310704-3 channel web to determine the trim angle for the aft vertical 
flange leg.  (Optional to use a mechanical protractor / angle finder or other device).  Alignment variances 
related to the aft end of the 310704-3 channel will require the 310364-7 tee to be trimmed on installation.  
Additional material has been left on the aft vertical fl ange leg (inbd / outbd) of the -7 tee to allow rotation 
on the parts axis +/- 6 degrees.  This will allow the forward flange leg to align with the 310704-3 channel 
aft end.  Refer to Dwg No. K310384, General Note #19 and Figure #1 located on Sheet 2 of 4 for 
minimum trim dimensions.  Restore part primer finish after trimming and de-burring. 
 
b. After the -7 tee has been trimmed and corrosion prot ection restored (Refer to Dwg No. K310384, General 
Note #19), locate the tee into the frame and mark existing hole locations on the tee from the baggage 
compartment.  Remove tee and determine if marked hole locations are acceptable by maintaining a 
minimum of 2D edge distance.  If hole locations are not acceptable, contact Twin Commander.  If hole 
locations are acceptable, match drill a ll -7 tee clip holes (8) and Cleco into place.  Use of shims between 
the tee horizontal flange and upper picture window channel  is acceptable to prevent fastener preload on 
assembly. 
 
c. If there are alignment issues, do not preload parts.   Refer to Dwg No. K310384, General Note #4 for 
additional instructions pertaining to shimming of parts. 
 
6. Machined strap instl (Aft side of  F.S. 178.81 & W.L. -14.00) area: 
 
a. Refer to K310384-Section A-A, B-B & C-C.  From the baggage compartment, locate the 310364-9 Strap 
per section A-A.  Remove the -7 Tee and mark the 4 attaching fastener locations on the -9 strap from the 
cabin side.  It is acceptable to trim the lower edge of  310420-13 clip to allow -9 strap to seat and maintain 
2D edge distance on the upper fastener.  Remove t he strap and determine if drilled hole locations are 
acceptable.  If hole locations are not acceptable, contact Twin Commander.  DO NOT INSTALL -9 
STRAP AND -7 TEE FASTENERS UNTIL ITEM 7.b. IS COMPLIED WITH. 
 
NOTE: 
SOME AIRCRAFT MAY BE CONF IGURED WITH AN EXISTING SH IM OF VARYING THICKNESSES 
INSTALLED BETWEEN THE 310420-13 CLIP AND THE AFT PRESSURE BULKHEAD WEB.  THIS 
SHIM WAS INSTALLED BY THE FACTORY AND MUST BE REPLACED WITH A LARGER SHIM (TO 
ACCOMMODATE THE 310364-9 STRAP ADDITION AL LENGTH) MADE FROM THE SAME 
THICKNESS AS REMOVED.  REFER TO DWG NO. K310384, GENERAL NOTE #4 FOR ADDITIONAL 
INSTRUCTIONS PERTAINING TO SHIMMING OF PARTS.

### Page 16

SERVICE BULLETIN 241 
Page  16  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
7. Remove all Cleco attached parts per Part II, Items #3 through #6. 
 
a. Refer to K310384-Section D-D.  Reinstall 310364-11 web, -3 channel and -5 strap in the same sequence 
as they were initially placed and located.  Mark all fa stener locations prior to drilling to verify they can be 
installed.  If fastener heads or butts interfere move fastener to clear.  Note:  If required, the outboard 
forward edge of the 310364-5 strap may be chamfered .063 x 45 degrees to provide clearance for solid 
rivet butts along the outboard flange. 
 
b. DO NOT REINSTALL 310364-7 TEE UNTIL:  
 
1) Refer to K310384-501, -503, & Section E-E.  310364- 3 channel outboard flange rivets in the area of 
the 310364-7 tee require special installation instructi ons.  Three existing #5 rivets reinstalled in the 
outboard skin channel flange (Highlighted in yellow, coded as “A” – Sect E-E) must have the rivet butt 
flushed to clear the 310364-5 strap and 310364-7 tee.  Back countersink the inboard side of the hole 
100 degree by .037-inch deep.  Install fasteners with the manufactured heads on the outboard side 
and buck the tail into the countersink.  Acceptable to  grind rivet butt flush with surrounding material.  
Restore corrosion protection to shaved rivets (Refer to Dwg No. K310384, General Note #19) 
 
2) Part II, fitting process complete. 
 
CAUTION: 
THE SUBSTITUTION OF BLIND RIVETS OTHER THAN THOSE INDICATED ON TWIN COMMANDER 
DWG NO. K310384 IN THE GENERAL NOTES OR ON THE FIELD OF DRAWING IS NOT PERMITTED 
WITHOUT AUTHORIZATION FROM THE AIRFRAME MANUFACTURE OR APPROVED BY A 
REPRESENTATIVE OF THE FAA. 
 
c. Refer to K310384-501, section E-E.  Cleco t he 310364-5 strap, 310364-7 tee and 310364-9 strap in 
place. 
 
d. Refer to K310384-501.  Install fasteners attaching the 310364-5 strap, 310364-7 tee and 310364-9 strap.  
Note:  Four fasteners attaching the -7 tee, require a special hole size per Dwg No. K310384, General 
Note #5.  Do not use reamer sizes for these fasteners as indicated on Dwg No. K310384, Rivet Code 
Block for these four fasteners.  Seal all parts per K310384, General Note #2. 
 
e. Refer to K310384 Section A-A.  Install or rein stall the 310704-3 channel over the picture window.  
Reinstall all fasteners at stub frame shear clips and along the outboard flange / skin attachment with the 
same type and size fastener removed.  Optional, to  substitute hardware per Dwg No. K310384, General 
Note #10, #15 and #20.  Part II, Item #2, d. may be  completed at this time  per Dwg No. K310384-503.  
Seal all parts per K310384, General Note #2. 
 
8. Before the cabin inner frame panel liners are reinstalled. 
 
a. For detailed procedures regarding fuselage seali ng, Refer to Twin Commander Aircraft LLC, Service 
Letter No. 382 “SEALING CABIN LEAKS IN AIRC RAFT PRESSURIZED TO THE FLOOR”, latest 
revision. 
 
b. All pressure boundary reworked areas that will be inaccessible once the panels are reinstalled should be 
checked for adequate sealant coverage.  Particular at tention to the area outboard of the added 310364-3 
channel between (W.L. -1.64 and W.L. -12.18). 
 
c. All applicable replaced and added fastener heads and or butts to be sealed per Service letter No 382. 
 
d. If the fiberglass cloth / sealant was damaged covering  the engine throttle control cables aft of F.S. 144.00 
during the removal of the 310704-1 channel,  refer to Twin Commander Aircraft LLC, Service Letter No. 
382 “SEALING CABIN LEAKS IN AIRCRAFT PRESSURI ZED TO THE FLOOR”, la test revision.” for 
application procedures on restoring the fuselage seal.

### Page 17

SERVICE BULLETIN 241 
Page  17  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
9. Cabin inner frame panel area (Picture Window support panels): 
 
a. Refer to K310384 Section A-A.  Position the exis ting 310736-85 and -143 inner skin panel in place.  
Match drill existing fastener hole positions from the inner skin panels to the 310704-3 channel.  Install 
Cleco fasteners in the panels to hold in place.  See CAUTION item 10.a. 
 
b. Refer to K310384-505.  Position the 310364-21 doubl er on the upper aft corner of the inner frame skin 
panels.  Additional material has been left on this part to allow trimming as necessary for adjustment due to 
existing fastener locations.  Note:  The 310364-21 doubler design replaces the factory installed 310736-
13 gusset and 310736-81 doubler.  These parts will not be reused and may be discarded.  Refer to Dwg. 
No. K310384, General Note #13. 
 
c. Refer to K310384-505 & Section A-A.  After the outer perimeter of the 310364-21 has been located, 
match drill existing fastener holes. Install adequate Cleco fa steners to hold in place.  Layout the trim lines 
for the added access hole installed fore / aft between (F.S. 172.50 and F.S. 178.81) and vertically 
between the 310704-3 channel and existing 310736-91 angl e.  The upper and lower cut out edges of the 
access hole to be flushed with the channel and angle parts edge.  For locating the  fore / aft cut out 
location of the access hole, Refer to K310384-505 and General Note #12. 
 
d. Make the access hole cutout in the existing 310736-143 panel and added 310364-21 doubler. 
 
e. Refer to K310384-505.  Four (per side) of th e existing fastener holes in the 310736-91 angle will be 
converted into removable bolts and nutplates. 
 
f. Refer to K310384-505.  Position the 310364-25 door over the 310364-21 doubler.  The 310364-25 door 
has four pilot hole locations used to locate the additional bolts and nutplates. 
 
g. Match drill 310364-25 door to the existing 12 fastener  hole locations (.1895 / .1915-in. dia. holes) in the 
310364-21 doubler.  Do not install 310364-25 door at this time. 
 
h. Refer to K310384 & Section A-A.  Install a new shea r clip to replace the prior removed 310736-45.  This 
clip attaches the existing aft end of the 310736-91 angle to the inboard flange leg of the added 310364-3 
channel.

### Page 18

SERVICE BULLETIN 241 
Page  18  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
10. Cabin inner panel to aft pressure bulkhead web attachment area: 
 
a. Refer to K310384-505 & Section H-H.  Position the 310364-23 angle as shown along the inboard side of 
the added 310364-3 channel and added 310364-21 doubler.  Additional material has been left on this part 
to allow top and bottom trimming as necessary for adjustment based on existing fastener locations.  The 
total fastener count as shown on Dwg No. K310384-505 instl must be maintained. 
 
CAUTION: 
DO NOT MATCH DRILL THE EXISTING FOUR FASTENER HOLE LOCATIONS (HIGHLIGHTED IN 
GREEN, CODED AS “B”) COMMON TO -23 ANGLE AND 31036 4-3 CHANNEL.  THESE HOLES 
ONLY ATTACH THE 310364-21 DOUBLER TO THE 310364-23 ANGLE. DAMAGE TO THE PRIOR 
INSTALLED 310364-7/-8 TEE WILL RESULT IF TH ESE HOLES ARE MATCH DRILL TO THE 310364-
3 CHANNEL.  THE FOUR EXISTING HOLES IN THE 310736-143 PANEL MUST BE DOUBLE FLUSH 
INSTALLED WITH AD RIVETS PER DWG. NO. K310384, GENERAL NOTE #14. 
 
b. Refer to K310384, Note 14.  Match drill existing fastener hole locations from the 310736-143 inner skin 
panels to the outboard flange leg of the 310364-23 angle, except the four per Caution Note.  Using a hole 
finder, locate and drill the four additional fastener s holes (Highlighted in green, coded as “B”)  on the 
outboard flange of the   -23 angle.  Attach the -23 angle and -21 doubler together with four NAS1097E5 or 
KE5 rivets with the manufactured head countersunk into the outboard side of the -21 doubler. 
 
c. Refer to K310384, Note 16 and 17.  Locate the -21 doubler with the -23 angle attached, to the 310736-
143 panel with clecos.  Match drill the existing fast ener, common to the main spar lower cap vertical 
flange.  If this fastener cannot be installed, see notes 16 & 17 for options. 
 
d. Refer to K310384, Section H-H.  Locate, drill and inst all the remaining additional fasteners attaching the 
aft flange of the 310364-23 angle to the 310364-11 web maintaining a minimum of .23-inch edge 
distance.  Seal all parts per K310384, General Note #2. 
 
e. Refer to K310384-505.  Install fasteners attaching the outboard flange leg of the 310364-23 angle, 
310364-21 doubler and 310736-143 panel.  Note:  These fasteners are not required to be installed wet or 
sealed over with sealant. 
 
f. Refer to K310384, Note 15.  Reinstall remaining inner skin panels between (F.S. 126.00 and F.S. 171.36) 
with the same type and size fastener removed.  Optional  to substitute fasteners per, General Note #15.  
Note:  These fasteners are not required to be installed wet or sealed over with sealant. 
 
11. Cabin inner frame panel access door: 
 
a. Refer to K310384-505.  Locate and install the 31 0364-25 door with the hardware indicated. Torque 
AN173-5A bolts to 25-35 inch-lbs.

### Page 19

SERVICE BULLETIN 241 
Page  19  of  20 
Part II - MODIFICATION & REASSEMBLY:  (continued) 
 
12. Corrosion preventative measures and sealants must be restored after inspections are completed. 
 
13. Reinstall the left and right hand cabin picture window assemblies. 
 
14. All replacement fasteners installed in the center wing upper and lower fuel tank compartments to have a 
minimum of two layers of tape per parts kit item 8 to cover fastener heads / butts that may contact the fuel 
tank cell.  It is not necessary to cover fasteners wi th tape that are concealed by the tank panel liners.  
Reinstall all tank panel liners with the same type and size fasteners that were removed.  Seal all tank panel 
liner fasteners that penetrate through the aft pressure bulkhead web at F.S. 178.81 pressure boundary. 
 
16. Reinstall the center wing fuel tank support foam (i nstalled on inboard / outboard sides of access hole / door.  
Replace if necessary.  Reinstall fuel tank cell and access door. 
 
17. Reinstall the center wing lower fuel tank support structure with the same type and size fasteners as removed.  
Reinstall fuel tank cell and reconnect all tank and pump fittings. 
 
18. Reinstall the left and right inboard wing fuel tank cells and ensure none of the repl aced fasteners contact the 
fuel tank cell and reconnect all tank fittings.  Reinstall fuel sump. 
 
19. Complete fuselage leak check of the pressurized cabin. 
 
20. Complete leak check of the reinstalled fuel system. 
 
21. CABIN SEALING 
 
For detailed procedures regarding fuselage sealing, Re fer to Twin Commander Aircraft LLC, Service Letter 
No. 382 “SEALING CABIN LEAKS IN AIRCRAFT PRESSURIZED TO THE FLOOR”, latest revision. 
 
22. Part II, modification and reassembly complete. 
 
 
 
ELECTRICAL LOAD: 
 
No change 
 
 
 
WEIGHT AND BALANCE: 
 
No significant change 
 
 
 
SPARES AFFECTED: 
 
None

### Page 20

SERVICE BULLETIN 241 
Page  20  of  20 
RECORD COMPLIANCE: 
 
Make an entry in the Aircraft Maintenance Records as follows:  Service Bulletin No. 241, dated September 26, 
2012, entitled “FUSELAGE ATTACHMENT TO WING MAIN SPAR - INSPECTION  & REINFORCEMENT”, 
complied with as follows: 
 
SB 241, Part I & II have been accomplished on aircraft m odel ________, serial number ________, with a current 
total airframe time of ___________ hours.  No recurring inspections are required, SB 241 is terminating action. 
 
 
Fill out information on the Compliance Card and mail postage paid form to: 
 
 TWIN COMMANDER AIRCRAFT, LLC. 
 Attn.:  SERVICE DEPARTMENT 
 1176 TELECOM DRIVE 
 CREEDMOOR, NC. 27522 
 
 or FAX to:   (919)-682-3786

### Page 21

Page  1  of  4 
 
SB 241 COMPLIANCE RECORD 
 
(Please fax to Twin Commander at # 919-682-3786 
or mail this postage paid form to address on reverse.) 
 
SERVICE BULLETIN NO. 241 
 
FUSELAGE ATTACHMENT TO WING MAIN SPAR – 
INSPECTION & REINFORCEMENT 
 
 
 MODEL _________ S/N ____________ REG. NO. ___________ TOTAL TIME ___________(HOURS) 
 
 OWNER NAME  ____________________________________________________________________ 
 
 ADDRESS  ________________________________________________________________________ 
 
 TELEPHONE NO.  (              )   FAX NO.  (             )  
 
 
 DAMAGE REPORT DURING COMPLIANCE WITH SB 241 
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I: (Has the aircraft undergone prior compliance with Twin Commander Custom Kit No. 
144 for the removal and replacement of the main spar lower cap) 
 
 YES  / NO   
 If Yes, date and total time when accomplished _____________________________ 
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #7, e: (Eddy Current inspection of the four LH and four RH holes common to the main spar 
lower cap fwd / aft flange outbd of W.S. 24.07) 
 
 Damage found: YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #7, f: (Fluorescent Dye Penetrant inspect the 1101 51-33/-34 fillet radius 4.0-inch fore / aft 
of F.S. 178.81) 
 
 Damage found: YES  / NO   
 Within limits:  YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #9, c: (Fluorescent Dye Penetrant inspect t he 310704-1/-2 channel outbd flange and lower 
web from F.S. 126.00 to F.S. 178.81) 
 
 Damage found: YES  / NO   
 Prior replaced: YES  / NO (310704-3 LH / -4 RH)  
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #10: (Inspection of the two LH and two RH pin and collar type fasteners attaching the 
310412-23/-24 shear clips for working of sheared conditions at F.S. 178.81 & 
 W.L. -14.00) 
 
 Damage found: YES  / NO   
 What type of hardware was installed:   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 
 cont.

### Page 22

Page  2  of  4 
 
 
 DAMAGE REPORT DURING COMPLIANCE WITH SB 241 (cont.) 
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #11, f: (Fluorescent Dye Penetrant inspect the 310384-159 web outbd edge at the main 
spar cap relief trim from W.L. -11.0 to W.L. -12.18) 
 
 Damage found: YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #11, i: (Fluorescent Dye Penetrant inspec t the 310384-65/-125 channels outbd flange, 
radius and web 4.0-inch above / below W.L. -12.18) 
 
 Damage found: YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #12, b: (Fluorescent Dye Penetrant inspect the .50-inch radius along the cutout of the 
forward flange at W.S. 24.07 on the main spar lower cap) 
 
 Damage found: YES  / NO   
 Evidence of part contact between the .50-inch radius or lower steel strap and the existing 
 310384-65/-125 channels outbd flange radius: 
 YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 Part I, Item #12, f: (Eddy Current inspection of the four .250-inch diameter LH and four RH holes 
common to the main spar upper and lower caps vertical flange leg attaching the 
310384-65/-125 and 310384-193 channels) 
 
 Damage found: YES  / NO   
-------------------------------------------------------------------------------------------------------------------------------------------- 
 
 DATE   ________ 
 
 WORK PERFORMED BY  (PRINTED) 
 
  (SIGNATURE) 
 
 COMPANY  ________________________________________________________________________ 
 
 ADDRESS  ________________________________________________________________________ 
 
                     ________________________________________________________________________ 
 
 TELEPHONE NO.  (              )   FAX NO.  (             )  
 
 EMAIL   ___________________________ 
 
 COMMENTS:  ______________________________________________________________________ 
 
 __________________________________________________________________________________ 
 
 __________________________________________________________________________________ 
 
 __________________________________________________________________________________ 
 
 __________________________________________________________________________________

### Page 23

Page  3  of  4 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
-  THIS PAGE LEFT BLANK INTENTIONALLY  -

### Page 24 (OCR)

NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST-CLASS MAIL PERMIT NO. 1 CREEDMOOR NC
POSTAGE WILL BE PAID BY ADDRESSEE
1176 Telecom Dr
Creedmoor NC 27522-9912
Page 4 of 4

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
