# Viking Air Alert Service Bulletin 215-A568: Revision 4

- Rights: © Viking Air. Filed by the FAA in regulations.gov docket FAA-2019-0710; AD 2019-25-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Viking Air Alert Service Bulletin 215-A568](https://openairdocs.org/service-documents/viking/215-a568.md)
- Title as filed: SB 215-A568 R4
- Pages: 48
- PDF: https://openairdocs.org/files/sha256/de/79/de791d41e0fb3ed805d9e77ca8f01caef27fa0f5393f63f8e13bac5dc56f7c57
- Page: https://openairdocs.org/service-documents/viking/215-a568/file/de791d41e0fb

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MODEL CL-215-1A10 
 
MODEL CL-215-6B11 
Page 1 of 2 ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
REVISION TRANSMITTAL SHEET 
ALERT SERVICE BULLETIN 
215−A568 
 
WINGS 
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA 
FOR CRACKS 
 
Service Bulletin No.: 215−A568  Date of Original Issue: 11-Dec-2015 
Revision No.: 4 Date of Issue: 22-Jan-2019 
 
 
NOTES: 1. For aircraft that complied with Revision 3 (or earlier) of this Service Bulletin 
(SB), it is required to do the following: 
a. Inspect additional locations and fastener holes (identified in Revision 4 of 
this SB, in accordance with applicable instructions in Section II.A); 
b. Replace the installed NAS1242AD rivets (on the drag angles specified in 
previous Revisions of this SB) with Titanium Hi-Lite fasteners in 
accordance with Section II.B (Revision 4 of this SB, one-time); 
c. Report existing standard SRM (Structural Repair Manual) and non-
standard repairs incorporated on wing box structures between WS 355L 
and WS 355R in accordance with Section II.C (Revision 4 of this SB, one-
time). Note that replacement of damaged wing box primary structural 
member is considered as a “repair”. 
2. This Revision supersedes Revision 3 of this SB. 
3. Black bars in the left hand (LH) margin of this Service Bulletin and the details 
on this Revision Transmittal Sheet describe changes made since the 
previous issue.

### Page 2

Page 2 of 2 ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
 
This Service Bulletin is re-issued to: 
1. Revise Section I.A Compliance to include total Water Drops (WD) and Total Operation Cycles 
(TOC) in addition to the existing Flight Hours (FH). Note that TOC = WD + water landings  
(non-water scooping/dropping operations) + Land Landings (LL). 
2. Specify initial/repeat inspections, compliance time and additional inspections in Section I.A and 
II.A. 
3. Change the installed NAS1242AD rivets (on the drag angle specified in previous Revisions of 
this SB) to Titanium Hi-Lite fasteners as specified in Section II.B. 
4. Require supporting the entire wing weight before removing fasteners from drag angles and 
fuselage attachment frames in Section II.A and II.B.  
5. Revise Section II.A to specify additional inspections of the drag angles and wing front/rear spar 
at vertical fuselage attachment frames. Further, the drag angles may be left in situ if no 
preventative REO or modification is to be installed and if the drag angle flange does not interfere 
with the hole probe while carrying out the fastener hole eddy current inspection, provided there 
is no crack found on the wing lower skin. 
6. Add Section II.C to identify and report existing standard SRM and non-standard repairs of other 
than Allowable Damage installed on wing box structures between WS 355L and WS 355R, on 
aircraft with (or more than) 7500 FH, or 10000 WD, or 12000 TOC, whichever occurs first.  
7. Revise Section III (Material Information) to remove Ultrasonic inspection equipment and add 
new fasteners.

### Page 3

MODEL CL-215-1A10  
 
MODEL CL-215-6B11 
Page 1 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
   
ALERT SERVICE BULLETIN 
215−A568 
 
WINGS 
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA 
FOR CRACKS  
I. Planning Information 
A. Compliance 
 
The inspection described in Revision 4 of this Service Bulletin (SB) is mandatory and is 
applicable to all model CL-215-1A10 (CL-215) and Model CL-215-6B11 (CL-215T). 
NOTES:  
(1) This Service Bulletin is applicable only to aircraft in the condition as originally 
delivered by Canadair and/or Bombardier Aerospace or as subsequently modified by 
Canadair and/or Bombardier Aerospace Service Bulletin(s).   
(2) Prior to incorporation of Revision 4 of this SB, the status of any related systems or 
structural modification(s) introduced by Supplementary Type Approval (STA) or 
equivalent action must be examined for compatibility with the inspections or 
modifications and test procedures (if applicable) detailed in this SB. 
(3) If standard SRM (Structural Repair Manual) or non-standard repairs were installed 
on wing lower skin or front/rear spar lower cap/web, or any of these parts were 
replaced, the structural configuration, fatigue crack prone location and/or the 
accumulated flight time (FH, WD or TOC) on the concerned components at the 
inspection areas as specified in Revision 4 of this SB would be changed. This 
condition may require an Alternative Means of Compliance (AMOC) against 
applicable ADs associated with Revision 4 of this SB and all other related SBs. 
SPECIAL NOTICE CONCERNING COMPLIANCE 
 
A TRANSPORT CANADA AIRWORTHINESS DIRECTIVE
MAY BE IMPOSED REGARDING THE CONTENT 
OF THIS SERVICE BULLETIN. 
OTHER REGULATORY AUTHORITIES MAY TAKE SIMILAR ACTION.

### Page 4

CL-215 
CL-215T 
 
Page 2 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
Contact Viking Air Ltd. (VAL) Technical Support for further inspection instructions to 
support AMOC application to local airworthiness authority, as required. Provide 
repair/replacement details, as listed in Section II.C, when contacting VAL Technical 
Support. 
1. Initial inspection threshold (see Table 1): within 7500 Flight Hours (FH), or 10,000 Water 
Drops (WD), or 12,000 Total Operation Cycles (TOC = water drops + water landings of 
non-water scooping/dropping operations + land landings), whichever occurs first. 
Perform the initial inspection in accordance with Section II.A of this SB (Revision 4). 
a. If cracks are found, before next flight, repair/replace damaged part(s) as necessary. 
Contact VAL Technical Support for Repair Engineering Order (REO) and/or aircraft 
specific ICA (Instructions for Continuing Airworthiness) that defines future inspection 
requirements. 
NOTE: The replacement and/or repair of the damaged parts (including wing lower 
skin, spar lower caps/webs) will change the structural configuration, fatigue 
crack prone location and/or the accumulated flight time (FH, WD or TOC) 
on the concerned components in the specified inspection areas.  This 
condition may require an AMOC against applicable Airworthiness Directives 
(ADs) associated with Revision 4 of this SB and all other related SBs. 
Contact VAL Technical Support for aircraft specific ICAs (defining future 
inspection requirements) to support AMOC application to local 
airworthiness authority, regardless if the damaged part(s) is (are) replaced 
or repaired per SRM or REO.  
b. If no cracks are found: 
(1) perform the repeat inspection in accordance with Para I.A.2 and Table 1 in 
Revision 4 of this SB; or  
(2) alternatively, install preventative REO 215-57-V022 (Revision NC or later),  
then perform the new initial and repeat inspections of the lower skin and other 
components (aircraft specific) as specified in that REO, and perform the repeat 
inspection of locations and fastener holes shown in Figure 1 (Sheet 3 and 4 
only), Revision 4 of this SB. Contact VAL Technical Support for REO  
215-57-V022. 
2. The repeat inspection intervals (see Table 1): thereafter the initial inspection and within 
every 3750 FH, or 5000 WD, or 6000 TOC, whichever occurs first. Perform the repeat 
inspection in accordance with Section II.A and Table 1 in Revision 4 of this SB. 
a. If cracks are found, before next flight, repair/replace damaged part(s) as necessary. 
Contact VAL Technical Support for REO and/or aircraft specific ICA that defines 
future inspection requirements.   
NOTE: The replacement and/or repair of the damaged parts (including wing lower 
skin, spar lower caps/webs) will change the structural configuration, fatigue 
crack prone location and/or the accumulated flight time (FH, WD or TOC) 
on the concerned components in the specified inspection areas.  This 
condition may require an AMOC against applicable ADs associated with 
Revision 4 of this SB and all other related SBs. Contact VAL Technical 
Support for aircraft specific ICAs (defining future inspection requirements)

### Page 5

CL-215 
CL-215T 
 
Page 3 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
to support AMOC application to local airworthiness authority, regardless if 
the damaged part(s) is (are) replaced or repaired per SRM or REO.  
b. If no cracks are found: 
(1) perform the repeat inspection in accordance with Section I.A.2 and Table 1 in 
Revision 4 of this SB; or 
(2) alternatively install preventative REO 215-57-V022 (Revision NC or later),  
then, perform the new initial and repeat inspections of the lower skin and other 
components (aircraft specific) as specified in this REO, and perform the repeat 
inspection of locations and fastener holes shown in Figure 1 (Sheet 3 and 4 
only), Revision 4 of this SB. Contact VAL Technical Support for REO  
215-57-V022. 
3. One-Time reporting of existing standard SRM and non-standard repairs (other than 
Allowable Damage) on wing box structures between WS 355L and WS 355R: on aircraft 
with (or more than) 7500 FH, or 10000 WD, or 12000 TOC, whichever occurs first. Note 
that replacement of damaged wing box primary structural member is considered as a 
“repair”. 
4. Phase-in schedule of Initial Inspection applicable to aircraft without incorporation of 
Revision 3 (or earlier) of SB 215-A568 (see Table 2): per one of the following Paragraphs 
a. to d. below, as applicable. The shortest compliance time among the following 
Paragraphs a. to d. shall apply if the accumulated aircraft flight times (FH, WD, TOC) 
meet multiple criteria: 
a. Aircraft with (or more than) 7500 FH, or 22001 WD or 26401 TOC: within 4 months 
from the issuing date of SB 215-A568 (Revision 4). 
b. Aircraft with 7500 FH or more, or 20001-22000 WD or 24001-26,400 TOC: within 8 
months from the issuing date of SB 215-A568 (Revision 4). 
c. Aircraft with 7500 FH or more, or 10000-20000 WD or 12000-24000 TOC: within 18 
months from the issuing date of SB 215-A568 (Revision 4). 
d. Aircraft with less than 7500 FH, and 10000 WD and 12000 TOC: at or before the 
Initial Inspection Threshold specified in Table 1 or within 18 months from the issuing 
date of SB 215-A568 (Revision 4), whichever occurs later. 
5. Phase-in schedule of Initial Inspection applicable to aircraft complied with Revision 3 or 
earlier of SB 215-A568 (see Table 3): per one of the following Paragraphs a. to c. below, 
as applicable. The shortest compliance time in Paragraphs a. or b. below shall apply if 
the accumulated aircraft flight times (FH, WD, TOC) meet both criteria: 
a. Aircraft with (or more than) 7500 FH, or 20001 WD or 24001 TOC: within 12 months 
from the issuing date of SB 215-A568 (Revision 4). 
b. Aircraft with 7500 FH or more, or 10000 - 20000 WD or 12000 - 24000 TOC: within 
18 months from the issuing date of SB 215-A568 (Revision 4). 
c. Aircraft with less than 7500 FH, and 10000 WD and 12000 TOC: at or before the 
Initial Inspection Threshold specified in Table 1 or within 18 months from the issuing 
date of SB 215-A568 (Revision 4), whichever occurs later.

### Page 6

CL-215 
CL-215T 
 
Page 4 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
d. At the “Initial Inspection” time, perform following actions: 
(1) Change the installed NAS1242AD rivets on the drag angles (specified in 
Revision 3 or earlier Revisions of this SB) to Titanium Hi-Lite fasteners in 
accordance with Section II.B, Revision 4 of this SB. Note that this is a one-time 
replacement only and all rivet holes common to drag angles are to be  
re-inspected while changing NAS1242AD rivets. 
(2) Perform the rest of the inspections identified in Section II.A, Revision 4 of this 
SB. 
(3) Thereafter, perform future Repeat Inspections per Table 1 schedule. 
6. Compliance time for reporting of existing repairs on wing box structure: 
a. Within 30 days after accomplishing the Initial Inspection as specified in Paragraph 
I.A.4 and I.A.5 (Revision 4 of this SB), report existing standard SRM and non-
standard repairs incorporated on wing box structures between WS 355L and WS 
355R in accordance with Section II.C, Revision 4 of this SB. Note that replacement 
of damaged wing box primary structural member is considered as a “repair”. 
7. Within 30 days after incorporation of the Initial and each Repeat Inspection per this 
Revision 4, return the SB 215-A568 Reply Form (attached at the end of this SB) to VAL 
Technical Support via email to technical.support@vikingair.com or via fax to 1-403-295-
8888. 
Table 1. Initial/Repeat Inspection Intervals and Reporting of Existing Repairs 
Description Flight Hours Water Drops Total Operation Cycles (1) Note Instruction 
Initial Inspection 
Threshold 7500 Or 10000 Or 12000 Whichever occurs first Per Section II.A 
Repeat Inspection (2) 3750 Or 5000 Or 6000 Whichever occurs first Per Section II.A 
Reporting of existing 
repairs on wing box (3) ≥7500 Or ≥10000 Or ≥12000 Whichever occurs first Per Section II.C 
(1) Total Operation Cycles = water drops + water landings (non-water scooping/dropping operations) 
+ land landings. 
(2) Alternatively, if preventative REO 215-57-V022 (Revision NC or later) is installed, perform the 
new initial and repeat inspections specified in that REO, and perform the repeat inspection of the 
locations and fastener holes shown in Figure 1 (Sheet 3 and 4 only). 
(3) Note that replacement of damaged wing box primary structural member is considered as a 
“repair”.

### Page 7

CL-215 
CL-215T 
 
Page 5 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
Table 2. Phase-in Schedule of the Initial Inspection (1) 
Flight 
Hours Water Drops Total Operation Cycles (2) Compliance Time Note 
≥7500 Or ≥22001 Or ≥26401 Within 4 months (3)(4) Whichever results 
in the shortest 
compliance time (5) 
≥7500 Or 20001 - 22000 Or 24001 - 26400 Within 8 months (3)(4) 
≥7500 Or 10000 - 20000 Or 12000 - 24000 Within 18 months (3)(4) 
<7500 And <10000 And <12000 
At or before Table 1 Initial 
Inspection Threshold or 
within 18 months (3)(4), 
whichever occurs later  
– 
(1) Applicable to aircraft without incorporation of Revision 3 (or earlier) of SB 215-A568. 
(2) Total Operation Cycles = water drops + water landings (non-water scooping/dropping operations) 
+ land landings. 
(3) From the issuing date of SB 215-A568 Revision 4 (flight hours, water drops, or total operation 
cycles are the accumulated numbers on the issuing date of SB 215-A568 Revision 4). 
(4) If standard SRM or non-standard repairs were installed on wing lower skin or front/rear spar lower 
cap/web, or any of these parts were replaced in the inspection areas specified in Revision 4 of this 
SB, the structural configuration, fatigue crack prone location and/or the accumulated flight time 
(FH, WD, TOC) on the concerned component(s) would be changed. This condition may require 
an AMOC against applicable ADs associated with Revision 4 of this SB and all other related SBs. 
Contact VAL Technical Support for further inspection instructions to support AMOC application to 
local airworthiness authority as required. Provide repair/replacement details as listed in Section II.C 
of this SB when contacting VAL Technical Support. 
(5) The shortest compliance time shall apply if the accumulated aircraft flight times (FH, WD, TOC) 
meet multiple criteria. 
Table 3. Phase-in Schedule of the Initial Inspection (1) 
Flight 
Hours Water Drops Total Operation  Cycles (2) Compliance Time Note 
≥7500 Or ≥ 20001 Or ≥ 24001 Within 12 months (3)(4)(5) Whichever results 
in the shortest 
compliance time (6) ≥7500 Or 10000 - 20000 Or 12000 - 24000 Within 18 months (3)(4)(5) 
<7500 And <10000 And <12000 
At or before Table 1 
Initial Inspection 
Threshold or within 18 
months (3)(4)(5), 
whichever occurs later  
– 
(1) Applicable to aircraft complied with Revision 3 (or earlier) of SB 215-A568. 
(2) Total Operation Cycles = water drops + water landings (non-water scooping/dropping operations) 
+ land landings. 
(3) From the issuing date of SB 215-A568 Revision 4 (flight hours, water drops, or total operation 
cycles are the accumulated numbers on the issuing date of SB 215-A568 Revision 4). 
(4) “Initial Inspection” includes following actions: 
a. Change the NAS1242AD rivets from the drag angles (specified in previous Revisions of this SB) in 
accordance with Section II.B, Revision 4 of this SB. Note that this is a one-time replacement and the 
rivet holes common to drag angles are to be re-inspected while changing NAS1242AD rivets.

### Page 8

CL-215 
CL-215T 
 
Page 6 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
b. Perform the rest of inspections identified in Section II.A (Revision 4 of this SB), then, perform the 
Repeat Inspection per Table 1 schedule thereafter. 
(5) The same as Note (4) in Table 2. 
(6) The shortest compliance time shall apply if the accumulated aircraft flight times (FH, WD, TOC) 
meet both criteria. 
B. Approval 
The technical content of this Service Bulletin has been approved under the authority of the 
Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO 04-V-02. 
C. Effectivity 
Aircraft Validity: This Service Bulletin is valid for CL-215-1A10 (CL-215) Piston and  
CL-215-6B11 (CL-215T) turboprop Aircraft Serial No. 1001 to 1125. 
Service Effectivity: This Service Bulletin is authorized for CL-215-1A10 (CL-215) Piston and 
CL-215-6B11 (CL-215T) turboprop Aircraft Serial No. 1001 to 1125. 
D. Reason 
Multiple cracks were found in fastener holes in the wing lower skin common to the closing 
drag angles, located at WS 51.00 on the Left Hand (LH) and Right Hand (RH) sides. New 
inspection intervals and additional inspections are needed to maintain the continuing 
airworthiness of the aircraft. Service history indicates that the aircraft structural condition is 
more related to the total number of water drops and/or total operation cycles than flight 
hours. This is reflected in initial/repeat inspection intervals, Revision 4 of this SB. 
Revision 4 of this SB also expands the scope of the inspections to include the drag angles 
and the wing front/rear spar to vertical fuselage attachment frame joints at wing root area. 
This is to prevent long, and/or multiple cracks hidden on wing lower skin and spar web/cap 
being possibly missed by existing inspections at the wing root area. Also, if cracks are 
detected and rectified in earlier stages (on aircraft with less severe usage or less 
accumulated FH, WD or TOC), the associated repair could be much simpler and 
subsequent cracks that could occur on the mating components may be eliminated or 
postponed. 
E. Description 
Within the compliance time and upon reaching the initial/repeat inspection intervals 
specified in Section I.A of SB 215-A568 Revision 4, perform Eddy Current fastener hole 
inspection with the drag angles removed (or in place if the drag angle flange does not 
interfere with the hole probe while carrying out the fastener hole eddy current inspection). A 
check for a gap condition which may exist between the drag angle and the wing lower skin 
is also required, before installation of the removed serviceable drag angles (or with 
serviceable drags in situ, if they are not removed). 
Within the compliance time specified in Table 3, the NAS1242AD rivets from the drag 
angles (installed on aircraft complied to Revision 3 or earlier of this SB) need to be changed 
to Titanium Hi-Lite fasteners, in accordance with Section II.B, Revision 4 of this SB. The 
rivet holes common to the drag angles will be re-inspected when changing the rivets. At the 
same time, perform the rest of the inspection in accordance with applicable instructions in 
Section II.A, Revision 4 of this SB. Then, perform the Repeat Inspection per Table 1 
thereafter.

### Page 9

CL-215 
CL-215T 
 
Page 7 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
To assess the overall wing structural conditions and specify further inspection of the wing 
box structures, it is needed to identify existing standard SRM and non-standard repairs of 
other than Allowable Damage (including replacements) installed on wing front/rear spar 
web, upper/lower caps, upper/lower skins, upper/lower stringer and ribs between WS 355L 
and WS 355R, with or without initial/repeat inspections specified. 
Optional preventative REO is offered for installation on the wing lower skin at the initial or 
future repeat inspection time. 
F. Manpower 
We estimate that it will take 2 technicians approximately 24 hours to complete the 
combination of eddy current and visual inspection described in this Service Bulletin. 
G. Material Availability 
This Service Bulletin includes no kit. 
H. Tool Availability 
The Eddy Current non-destructive testing equipment is commercially available. You will 
need to obtain the use of the following: 
The fastener hole inspection requires the following equipment: 
– Hocking Phasec 2200, Eddy Current−Instrument−Impedance−Plane Type, or equivalent 
– Hocking 33A100 Mini Drive Unit, or equivalent 
– Hocking 33A103, Cable−Mini Drive Unit, or equivalent 
– Calibration Reference Standard BH7475−T7351, or equivalent 
– Techna NDT HRY 0.125 to 0.156, rotating bolt − hole probe, 100 kHz − 2.0 MHz 
frequency, adjustable, 0.125 to 0.156−inch. adjustable diameter, 2.0−inch length, or 
equivalent 
– Techna NDT HRY 0.156 to 0.187, rotating bolt − hole probe, 100 kHz − 2.0 MHz 
frequency, adjustable, 0.156 to 0.187−inch. adjustable diameter, 2.0−inch length, or 
equivalent. 
The Eddy Current surface scan inspection requires the following equipment: 
– Hocking Phasec 2200, Eddy Current−Instrument−Impedance−Plane Type, or equivalent 
– Coaxial cable, BNC to Microdot 
– Calibration Reference Standard AL29−32, or equivalent 
– Techna NDT PEN45−6, 45° Surface probe, 50 kHz to 500 kHz frequency, Fe/NFe, 
absolute, shielded, 0.125−in. (3.175−mm) diameter, 6.0−in. (152.4−mm) length, 
0.500−in (12.7 mm) drop, or equivalent 
I. Weight and Balance 
Not affected.

### Page 10

CL-215 
CL-215T 
 
Page 8 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
J. Electrical Load Data 
Not affected. 
K. References 
None.  
L. Publications Affected 
PSP 296, Non-Destructive Testing Manual, Part 1 General, 51−15−03 Eddy Current. 
M. Related Service Bulletin 
None. 
This Service Bulletin is self-contained. No drawings are supplied. For more information please 
contact: 
Viking Air Limited (VAL) FAX: 403-295-8888 
Technical Support Telephone Numbers: 
7757 8th Street NE Regional: 587-430-0572 
Calgary, Alberta North America: 1-800-663-8444 
Canada, T2E 8A2 technical.support@vikingair.com

### Page 11

CL-215 
CL-215T 
 
Page 9 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
II. Accomplishment Instructions 
NOTES: 
(1) For this modification, it is assumed that standard maintenance and repair practices will 
be applied, in accordance with applicable Product Support Publications (PSP). 
(2) For information regarding Hi-Lite fasteners, refer to PSP 297, Structural Repair 
Manual, Chapter 51−43−19 HI-LITES − GENERAL PROCEDURES. 
(3) For information regarding Hi-Lok fasteners, refer to PSP 297, Structural Repair 
Manual, Chapter 51−43−16 HI-LOKS − GENERAL PROCEDURES. 
(4) For information regarding the removal and application of primer and paint, refer to PSP 
297, Structural Repair Manual, Chapter 51−52−16 CORROSION PREVENTIVE 
TREATMENT − GENERAL PROCEDURES. 
(5) For information regarding leveling of the aircraft: 
For CL-215 aircraft, refer to PSP 292, Aircraft Maintenance Manual, Chapter 8−20−00 
LEVELING − MAINTENANCE PRACTICES. 
FOR CL-215T aircraft, refer to PSP 392, Aircraft Maintenance Manual, Chapter 
8−10−00 LEVELING − MAINTENANCE PRACTICES. 
(6) For information regarding the removal and installation of fuel cells: 
For CL-215 aircraft, refer to PSP 292, Aircraft Maintenance Manual, Chapter 
28−11−01 FUEL CELL − REMOVAL/INSTALLATION. 
For CL-215T aircraft, refer to PSP 392, Aircraft Maintenance Manual, Chapter 
28−11−01 FUEL CELL − REMOVAL/INSTALLATION. 
(7) For information regarding the removal and installation of solid rivets, refer to PSP 297 
Structural Repair Manual, Chapter 51−42−11 SOLID RIVETS − GENERAL 
PROCEDURES. 
(8) For information regarding the application of sealants, refer to PSP 297 Structural 
Repair Manual, Chapter 51−55−00 SEALING − GENERAL PROCEDURES. 
(9) For information regarding the application of repair reference markings to the aircraft, 
refer to PSP 297, Structural Repair Manual, Chapter 51−59−00 IDENTIFICATION OF 
REPAIR PARTS AND ASSEMBLIES. 
(10) If standard SRM or non-standard repairs were installed on wing lower skin or front/rear 
spar lower cap/web, or any of these parts were replaced in the inspection areas specified 
in Revision 4 of this SB, the structural configuration, fatigue crack prone location and/or 
the accumulated flight time (FH, WD, TOC) on the concerned component(s) would be 
changed. This condition may require an AMOC against applicable ADs associated with 
Revision 4 of this SB and all other related SBs. Contact VAL Technical Support for 
further inspection instructions to support AMOC application to local airworthiness 
authority as required. Provide repair/replacement details as listed in Section II.C of this 
SB when contacting VAL Technical Support.

### Page 12

CL-215 
CL-215T 
 
Page 10 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
A. Combination Visual and Eddy Current  Inspection 
Refer to Figure 1. 
1. Prepare the aircraft for the visual and the eddy current inspection as follows. Support 
the entire wing weight (including engines, accessory components and fluid) by jacking 
up the wing with suitable cradles positioned at WS 91.2L/R and/or 212L/R under the 
ribs. This is to “zero-load” the wing to fuselage joints. Refer to applicable maintenance 
manuals for the wing weight (depending on the wing condition, it may be in the order of 
22,500 lbs. with zero fuel). 
a. Remove the LH and RH side No. 2 fuel cell. 
For CL-215 Aircraft, refer to PSP 292 Chapter 28.  
For CL-215T Aircraft, refer to PSP 392 Chapter 28. 
b. B efore removing fasteners identified in Figure 1, check the fastener installation for 
abnormal conditions (missed, sheared, distorted, deformed or loose fastener 
heads/collar/nuts and corrosion). 
U sing the inspection Reply Form provided with this Service Bulletin, record the 
results, taking note of the type and location of any damage indication. Submit all 
your findings to VAL Technical Support. 
NOTE: A photographic record of the damage attached to the inspection Reply Form 
is highly recommended. 
c. See Notes (1) to (3) below. Remove identified fasteners and the front and rear drag 
angles 215−30031 from both the LH and RH sides as shown in Figure 1 Sheet 1 and 
Sheet 2. Remove identified fasteners from the wing front and rear spar (on both the 
LH and RH sides) as shown in Figure 1 Sheet 3 and Sheet 4. Take care to avoid 
damaging the fastener holes prior to inspection. Refer to PSP 297, Chapter 51. 
NOTES:  
(1) On wings with  Standard SRM or Non-Standard repairs (including REO) installed 
on wing lower skin or front/rear spar lower cap/web, or any of these parts were 
replaced in the inspection areas specified in Revision 4 of this SB, the structural 
configuration, fatigue crack prone location and/or the accumulated flight time 
(FH, WD or TOC) on the concerned components at the inspection areas as 
specified in Revision 4 of this SB would be changed. This condition may require 
an AMOC against applicable ADs associated with Revision 4 of this SB and all 
other related SBs. Contact Viking Air Ltd. (VAL) Technical Support for further 
inspection instructions to support AMOC application to local airworthiness 
authority, as required. Provide repair/replacement details as listed in Section II.C 
when contacting VAL Technical Support. 
(2) If no preventative modification (or REO 215-57-V022) is to be installed and if the 
drag angle flange does not interfere with the hole probe while carrying out the 
fastener hole eddy current inspection, the drag angle may not need to be 
removed. I.e.: the fasteners on the vertical flange of the drag angles do not need 
to be removed between FS 388.86 and 434.836 (see Figure 1 Sheet 1), but the 
fasteners identified forward of FS 388.86 and aft of FS 434.836 still need to be 
removed to inspect the fastener holes.

### Page 13

CL-215 
CL-215T 
 
Page 11 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
(3) Do not enlarge or rework the fastener holes before collecting and sending the 
inspection results back to VAL Technical Support. 
d. Using suitable solvents, such as dry-cleaning solvent P−D−680 or aliphatic naphtha 
TT−N−95, clean the inspection areas and surfaces of all traces of dirt, grease, or 
sealant. Take extra care to make sure that all fastener holes are clean (using a 
suitable bristle hole brush to clean fasteners hole bore, as required). 
e. Inspect the paint finish within the inspection area. If the finish is in good condition, 
then no additional preparation is required. 
If the paint finish is deteriorated, remove the paint and primer from the inspection 
area. 
2. Do the Visual Inspection of the drag angles, wing lower skin, lower stringers, spar lower 
caps/webs, and fuselage structures (internally and externally) where fasteners are 
removed on both LH and RH sides as follows: 
Equipment and Materials: 
DESCRIPTION PART NO./ SPECIFICATION QTY ITEM NO. 
Explosion Proof Light Commercial  1 − 
Magnifying lenses, 10X or better Commercial 1 − 
Borescope with 10X magnifying 
lens (and illumination if 
available) 
Commercial 1 − 
Bristle hole brush (suitable to 
hole diameters being inspected) Commercial AR − 
a. Using suitable lighting and visual aids such as mirrors, magnifying lenses, and/or 
borescope, visually inspect: 
– all open fastener holes for cracks, burrs, elongation, double or mis-drilled holes, 
or corrosion. 
– the accessible skin, stringers, spar lower caps/webs and vertical fuselage frames 
for surface cracks or evidence of distortion and surface defects (scratches, 
gouges, nicks, scores, dents, surface pitting/corrosion, or other surface 
damage). 
– If the drag angles are removed, visually inspect the drag angles and the skin on 
mating surfaces separately for defects mentioned above. 
– If the drag angles are not removed, visually inspect the drag angles in situ for 
defects mentioned above. Also check the mating surface between the wing lower 
skin surface and the drag angle upper flanges (along both inboard and outboard 
edges) for possible gaps. Remove fillet sealant along the drag angle upper 
flanges, as required.

### Page 14

CL-215 
CL-215T 
 
Page 12 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
Using the inspection Reply Form provided with this Service Bulletin, record the 
inspection results, taking note of the type and location of any damage indication 
(including any gap between the drag angle and the lower skin as applicable).  
Submit all your findings to VAL Technical Support. 
NOTE: A photographic record of the damage attached to the inspection Reply Form 
is highly recommended. 
b. Where necessary, and at the direction of VAL Technical Support, repair surface 
damage and the fastener holes affected by burrs, elongation, double or mis-drilled 
holes, or corrosion. 
NOTE: Depending on the results of the visual inspection, VAL Technical Support 
may also provide instruction to carry out additional rework at this step.

### Page 15 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
So
BL
51.00
215-10044
(WING LOWER SKIN)
(REF)
388.86  FS  - See NOTE below R 1  STR 2  STR 3  IFS  STR 4  STR 5
404.19
FRONT SPAR
(REF)
215-30031-26  See NOTE below
(FRONT DRAG ANGLE)
IFS
INSPECT ALL IDENTIFIED FASTENER HOLES ON  434.836
DRAG ANGLE AND FUSELAGE STRUCTURES
FOR CRACKS  STR 6  STR 7  STR 8  STR 9  STR 10  REAR SPAR
FS  (REF)
419.52
215-30031-8
(REAR DRAG ANGLE)
B  /2  HOLES ON DRAG ANGLE AND FUSELAGE  INSPECT ALL IDENTIFIED FASTENER
STRUCTURES FOR CRACKS
NOTE: If the drag angles are not to be removed, there is no need to remove fasteners and inspect fastener
holes on the vertical flange of the drag angles between FS 388.86 to 434.836. But, the fastener holes
identified forward of FS 388.86 and aft of FS 434.836 still need inspection.
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA
FOR CRACKS
FIGURE 1, SHEET 1 of 5
Page 13 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 16 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
STR 2  STR 3  STR 4  STR 5
STR 1
......
215-30031-26
(FRONT DRAG ANGLE)  215-10044
(WING LOWER SKIN)
INSPECT ALL IDENTIFIED FASTENER  (REF)
HOLES ON WING LOWER SKIN, LOWER
STRINGER AND SPAR LOWER CAP FOR
CRACKS
STR 8  STR 9  STR 10
STR 6  STR 7
INSPECT ALL IDENTIFIED FASTENER HOLES 215-30031-8
215-10044  (WING LOWER SKIN)  ON WING LOWER SKIN, LOWER STRINGER _ (REAR DRAG ANGLE)  AND SPAR LOWER CAP FOR CRACKS
(REF)
D
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA
FOR CRACKS
FIGURE 1, SHEET 2 of 5
Page 14 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 17 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
LBL  FRONT SPAR
51.00  UPPER CAP (REF)
• FRONT SPAR
WEB (REF)  FS
FRONT SPAR WEB (REF)  388.86
SPAR LOWER CAP AND  /POTENTIAL CRACK ON  • FRAME ANGLE  (OUTBOARD)  FRONT SPAR
\WEB
FRONT SPAR
LOWER CAP
AIRCRAFT
INSPECT 2 FASTENER HOLES ON  FAIRING (REF)
WING SKIN
WING SPAR WEB, SPAR LOWER  BOTTOM (REF)
CAP AND THE VERTICAL
FUSELAGE FRAME ANGLE/EB
FOR CRACKS  FRONT SPAR
LOWER CAP
- STRAP
(REF)
INSPECT DRAG
ANGLE FOR CRACKS
INNER FRAME ANGLE  OUTER FRAME ANGLE
(FRONT SPAR)  (FRONT SPAR)
OUTBOARD FRAME ANGLE
B - B
VIEW ON FRONT SPAR LOOKING AFT
LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA
FOR CRACKS
FIGURE 1, SHEET 3 of 5
Page 15 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 18 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
388.86  FS  434.83  RBL 51.00  UPPER CAP (REF)  REAR SPAR
434.83  REAR SPAR WEB
(REF)
•  REAR SPAR  FRAME ANGLE
(OUTBOARD)
POTENTIAL CRACK ON
REAR SPAR  SPAR LOWER CAP AND
WEB (REF)  N WEB
•  REAR SPAR
LOWER CAF
FAIRING (REF)
WING SKIN
BOTTOM (REF)
INSPECT 4 FASTENER HOLES ON  STRAP
WING SPAR WEB, SPAR LOWER
CAP AND THE VERTICAL
FUSELAGE FRAME ANGLEWEB
FOR CRACKS
REAR SPAR  B- B
LOWER CAP (REF)
INSPECT DRAG
ANGLE FOR CRACKS
INNER FRAME ANGLE  OUTER FRAME ANGLE
(FRONT SPAR)  (FRONT SPAR)
VIEW ON REAR SPAR LOOKING FWD
RIGHT SIDE SHOWN, LEFT SIDE OPPOSITE
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA
FOR CRACKS
FIGURE 1, SHEET 4 of 5
Page 16 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 19

CL-215 
CL-215T 
 
Page 17 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
FASTENER IDENTIFICATION AND POSITION CODING TABLE 
 REFERENCE HOLE POSITIONS 
 
HST10AG − (6) − ( ) PIN (STANDARD SIZED) + NAS1149D0316K WASHER + KFN 587− (6), OR 
HST110AG − (10) − ( ) PIN (1ST OVERSIZED) + NAS1149D0316K WASHER + KFN 600− (10)  
Fig 1: Sheet 1 
Fig 1: Sheet 2 
  HST10AG − (6) − ( ) PIN + NAS1149D0316K WASHER + KFN 587− (6), OR  HST110AG − (6) − ( ) PIN (1ST OVERSIZED) + NAS1149D0316K WASHER + KFN 600− (6)  Fig 1: Sheet 1 
 
 HST12AG − (6) − ( ) PIN (STANDARD SIZE) + NAS1149D0316K WASHER + KFN 673− (6), OR 
 HST112AG − (6) − ( ) PIN (1ST OVERSIZED) + NAS1149D0316K WASHER + KFN 673− (6)  
 HST412AG − (6) − ( ) PIN (2ND OVERSIZED) + NAS1149DN0416K WASHER + KFN 673− (6) 
Fig 1: Sheet 4 
 
 HL32PB − (8) − ( ) PIN (STANDARD SIZE) + HL273− (8) COLLAR 
 HL36PB − (8) − ( ) PIN (1ST OVERSIZED) + HL273− (8) COLLAR) 
 HL136PB − (8) − ( ) PIN (2ND OVERSIZED) + HL273− (8) COLLAR) 
 HL32PB − (10) − ( ) PIN (STANDARD SIZE) + HL273− (10) COLLAR 
 HL36PB − (10) − ( ) PIN (1ST OVERSIZED) + HL273− (10) COLLAR) 
 HL136PB − (10) − ( ) PIN (2ND OVERSIZED) + HL273− (10) COLLAR) 
Fig 1: Sheet 3 
  HL32PB − (10) − ( ) PIN (STANDARD SIZE) + HL273− (10) COLLAR  HL36PB − (10) − ( ) PIN (1ST OVERSIZED) + HL273− (10) COLLAR) 
 HL136PB − (10) − ( ) PIN (2ND OVERSIZED) + HL273− (10) COLLAR) 
Fig 1: Sheet 4 
NOTES: 
1. LH shown RH opposite. Support the entire wing weight (including engines and accessory components and 
fluid) by jacking up the wing with suitable cradles positioned at WS 91.2L/R and/or 212L/R under the ribs. 
This is to zero-load the wing to fuselage joints (to minimize fastener load), i.e., the support cradles are not 
put into a “snug” contact with the wing lower face. The support cradles should be slightly jacked up to 
remove the entire wing weight from fuselage support structure. Refer to applicable maintenance manuals 
for the wing weight (depending on the wing condition, it may be in the order of 22500 lbs. with zero fuel).  
2. Remove existing fasteners as identified in Figure 1 (Sheet 1 to Sheet 4) and do the Eddy Current 
inspection using a rotating hole Probe through all layers in all open holes on both LH and RH sides for 
cracks on wing lower skin, front/rear spar lower caps/web and fuselage structures. If any cracks found, 
report to VAL Technical Support for further instructions. 
If no preventative modification (or REO 215-57-V022) is to be installed, the existing LH/RH front and rear 
drag angles (215−30031) may not need to be removed if the drag angle flange does not interfere with the 
rotating hole probe while carrying out the fastener hole eddy current inspection.  
3. If the drag angles are removed, do the Eddy Current inspection using a rotating hole Probe on the existing 
LH/RH front and rear drag angles (215−30031) for cracks in all fastener holes. Also inspect all drag angles 
for cracks along the bending radius using the Eddy Current surface scan probe, regardless if the drag 
angles are removed or not. If any cracks found, report to VAL Technical Support for further instructions.  
4. If no cracks are detected, re-install existing LH/RH front and rear drag angles (215−30031, if removed and 
serviceable). Ensure the LH/RH drag angles (215−30031) sit properly matching the contour of wing lower 
skin (215−10044). If gaps found in between drag angles and wing lower skins, report to VAL Technical 
Support for further instructions. 
5. If no gap exists between drag angles and wing lower skin, install LH and RH drag angles (215−30031) 
using fasteners as shown in fastener identification and position table. Report to VAL Technical Support if 
MIN 1.8D (D = Fastener Hole Diameter) edge distance requirement cannot be achieved.  
6. If possible, always use smaller fastener size with proper fit. 
7. Inspect the drag angles for crack along the bending radius using Eddy Current Surface Scan.  
8. NAS1149 washers are used to prevent scratching damage to skin/stringer surface by the KFN nuts.  
9. Contact VAL Technical Support for help if fastener size other than specified above is required due to other 
modification. 
INSPECTION OF WING AND FUSELAGE ATTACHMENT STRUCTURES AT WING ROOT AREA 
FOR CRACKS 
FIGURE 1, SHEET 5 of 5  
6 
6 
6 
6 
6

### Page 20

CL-215 
CL-215T 
 
Page 18 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
The Eddy Current inspection that follows must be signed off by qualified personnel as 
required by the local regulatory authorities. 
Equipment and Materials: 
DESCRIPTION PART NO./  SPECIFICATION UNITS PER ASSEMBLY ITEM NO. 
Eddy Current Instrument, 
Impedance-Plane Type 
Hocking Phasec 2200  
or equivalent 
1 − 
Mini Drive Unit Hocking 33A100  
or equivalent 
1 − 
Cable for Mini Drive Unit, Hocking 33A103 
or equivalent 
1 − 
Calibration−Reference 
Standard, conductivity value 
between 39% and 45% IACS 
that contains various hole 
sizes with 0.040 – inch  
(1.02 − mm) deep electrical 
discharge machined (EDM) 
notches. 
BH7475−T7351  
(see Figure 3) 
 or equivalent 
1 − 
Rotating Bolt − Hole Probe, 
100 kHz − 2.0 MHz frequency, 
adjustable, 0.125 to 
0.156−inch. adjustable 
diameter, 2.0−inch length 
Techna NDT HRY  
0.125 to 0.156  
or equivalent 
1 − 
Rotating Bolt − Hole Probe, 
100 kHz − 2.0 MHz frequency, 
adjustable, 0.156 to 
0.187−inch. adjustable 
diameter, 2.0−inch length. 
Techna NDT HRY  
0.156 to 0.187 
or equivalent 
1 − 
NOTE: If equivalent equipment is used, it must satisfy the requirement of the task and 
resolve the reference notches in the calibration reference standard at the required 
level of resolution and sensitivity

### Page 21

CL-215 
CL-215T 
 
Page 19 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
3. Do the Bolt Hole Eddy Current (BHEC) inspection using a rotating Probe of the fastener 
holes as follows: 
NOTE:  If the drag angles are removed, they shall be inspected separately. 
a. Preparation and Cleaning 
Visually inspect the hole to be inspected for conditions that may interfere with the 
inspection such as burrs, sealant, galling, out of round conditions or offset at 
component interfaces.  Using a suitable bristle hole brush to clean fasteners hole 
bore, as required. 
NOTE: Magnifying glass, borescope or other optical aids may be used to enhance 
the visual inspection. 
If a reaming operation is required to correct the above conditions, permission must 
be obtained from VAL Technical Support before enlarging any hole. 
Refer to Figure 2, Figure 3, Figure 4, and Figure 5 
b. Calibrate the BHEC inspection equipment as follows: 
(1) Connect the cable and the drive unit to the eddy current instrument. Attach the 
rotating probe that represents the diameter of the fastener hole to be inspected. 
Refer to Figure 4. 
(2) Adjust the probe to fit the same diameter hole, on the calibration reference 
standard, as the fastener hole to be inspected. Refer to Figure 4. 
NOTE: There should be light friction while inserting and removing the probe into 
and from the fastener hole. Excessive friction will cause wear on the 
coil. 
(3) Turn the instrument ON and set the instrument to the XY display mode and 
adjust the instrument settings for phase angle calibration as shown in Figure 2. 
NOTE: The screen displays show the results of the instruments used in the job 
and equipment step. Other frequencies and settings may be used if the 
requirements of this calibration are met. 
(4) Align and insert the rotating probe into the equivalent diameter hole in the 
calibration reference standard containing a 0.040−inch (1.02−mm) EDM notch or 
the 0.050−inch (1.27 mm) long corner EDM notch for countersinks. Refer to 
Figure 3. 
Start the rotating drive unit and adjust the instrument phase (rotation) control to 
position the EDM notch signal in the vertical direction. 
(5) Perform the sensitivity calibration. Change the instrument setting to the YT 
display mode as shown in Figure 2. 
(6) Align and insert the rotating probe into the equivalent diameter hole, in the 
calibration reference standard containing a 0.040−inch (1.02−mm) EDM notch or 
the 0.050−inch (1.27 mm) long corner EDM notch for countersinks. 
Maximize the signal from the EDM notch and adjust the Gain control to give a 
100% amplitude signal above the zero datum. Refer to Figure 2.

### Page 22 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
INSTRUMENT SETTINGS  SCREEN DISPLAY (XY)
EDM NOTCH SIGNAL
Freq.  Rotary  Display  RPM  33A100  1500  500 kHz  100%  80%  60%  40%
Phase  270.0°  20%
Gain  33.0 dB  (ZERO  0%
X:Y  0.0 dB  DATUM)
Hi-Pass  100 Hz
Lo-Pass  1500 Hz
X-Pos
Y-Pos  90°  180°  270°  360°
CALIBRATION SHOWN FOR XY MODE
INSTRUMENT SETTINGS  SCREEN DISPLAY (YT)
EDM NOTCH SIGNAL
Rotary  33A100
RPM  1500  100%
Display  YT  80%
Freq.  500 kHz  60%  40%
Phase  270.0°  20%
Gain  33.0 dB  0%
X:Y  0.0 dB  (ZERO
Hi-Pass  100 Hz  DATUM)
Lo-Pass  1500 Hz
X-Pos
Y-Pos  0°  90°  180°  270°  360°
CALIBRATION SHOWN FOR YT MODE
FIGURE 2
Page 20 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 23 (OCR)

CL-215  VIKING
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
4.50 in.  1.50 in.  FOUR EQUALLY SPACED
(114,30 mm)  (38.10 mm)  0.75 IN. (19,05 mm)
APART
(25,40 mm)  1.00 in.  ơ‡Õ  010.2  0.156 in.  (3.96 mm)  (DIA.)  0.375 in.  0.406 in.  (10,31 mm  (DIA.)  10.437 in..  7(11.10 mm)  •(DIA.)
0.75 in.  2888.
(19,05 mm)
1.00 in.  BH7475-T7351
(25,40 mm)
0.75 in.
(19,05 mm)
.250  0.281 in.  (7,14 mm  (DIA.)  0.312 in.  (7,92 mm)  (DIA.)  0.344 in.  (8,74 mm)  (DIA.)  '0.500 in.  (12,70 mm)  (DIA.)
0.250 in  6.00 in.
(6,35 mm)  (6,35 mm)
CALIBRATION REFERENCE STANDARD
NOTES
BH7475-T7351
1. Material is 7475-T7351.
2. Break all sharp edges 0.015 in. (0,381 mm).
0.500 in.
3. Ream and deburr all holes.  (12,70 mm)  5) 0.040 in. (1,02 mm)
4. All above dimensions are for reference only.  (DIA.)  • EDM NOTCH
\ EDM notch 0.005 in. (0,127 mm) +0.000 or  (TYPICAL)
-0.002 in. (+0,000-0,050 mm) wide x 0.040 in.
(1.02 mm) long, through. Total number of
notches is 10.
Identification sticker, 0.125 in. (3,75 mm)  letters, black color.  A-A
CALIBRATION REFERENCE STANDARD BH7475-T7351
FIGURE 3
Page 21 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 24 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
START
BUTTON
MINI DRIVE UNIT
CABLE 33A103  33A100
FIXED DIAMETER TYPE
BOLT-HOLE PROBE
D - 0.006 IN. MAX.  POSSIBLE CRACK
LOCATION
TO PHASEC 2200
ET INSTRUMENT
HOLE SIZE TO BE
INSPECTED (D)
ADJUSTABLE
COLLAR
ADJUSTABLE DIAMETER TYPE —  →
ROTATING BOLT-HOLE PROBE
EXAMPLES OF BOLTHOLE PROBE SET-UP
FIGURE 4
Page 22 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 25 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
100%
80%
60% -
40%
20%
0°  90°  180°  270°  360°
CRT DISPLAY OF HOLE E (NO CRACK)
O E
100%  C
80%
%09
%Ot
20%  D
C
Ö°  90°  180°  270°  360°
CRACKS ALONG ZERO DATUM (TIME BASE)
FOR HOLES A THRU D
• в
CABLE 33A103  OA
TO PHASEC 2200
ET INSTRUMENT
ORIENTATION OF DRIVE UNIT TO CRACKS RELATIVE TO HOLE CIRCUMFERENCE AND CRT
DISPLAYS
FIGURE 5
Page 23 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 26

CL-215 
CL-215T 
 
Page 24 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
(7) Ensure the signal to noise ratio does not exceed 10% from the screen display 
center line. 
(8) Note the relative position of the drive unit with the notch at 180°, or at the center 
of the screen display as shown in Figure 5. 
Refer to Figure 1, Figure 4, and Figure 5 
The BHEC inspection using the rotating probe is applicable to all identified fastener 
holes (except reference holes) indicated in Figure 1. 
c. BHEC Inspection Using Rotating Probe 
Starting at the front spar (reference FS 388.85) and progressing to the rear spar 
(reference FS 434.84) along the WS 51.00 reference line, do the Eddy Current 
fastener hole scan of all open holes, LH and RH sides, through all layers as follows: 
NOTE: If the drag angles are removed, BHEC Inspection of the drag angle 
fastener holes shall be carried out separately using rotating hole probe. 
(1) Insert the rotating probe perpendicular to the fastener hole to be inspected and 
adjust the probe diameter if required. Turn the drive unit ON and inspect the 
entire bore of the fastener hole. Turn the drive unit OFF before withdrawing the 
probe. 
(2) Rotate the drive unit 90° and repeat previous step c.(1). 
(3) If applicable, insert the countersink rotating probe perpendicular to the fastener 
hole to be inspected. Turn the drive unit ON and inspect the entire countersink of 
the fastener hole. Turn the drive unit OFF before withdrawing the probe. 
(4) Scan the remaining open holes as shown in Figure 1. 
(5) Using the inspection Reply Form provided with this Service Bulletin, record the 
results, taking note of the type and location of any damage indication. Submit all 
your findings to VAL Technical Support. 
NOTE: A photographic record of the damage attached to the inspection Reply 
Form is highly recommended. 
Do the evaluation of indications as follows: 
d. To determine the depth of indicated bore cracks parallel to the hole axis, do the 
following: 
(1) Align and insert the rotating probe slowly and carefully into the fastener hole 
containing the crack indication, until a maximized vertical signal from the crack is 
displayed on the screen display. Adjust the GAIN control to obtain a 100% FSH 
vertical signal above the zero datum from the crack. 
(2) Feed the probe through the fastener hole until a 25% FSH vertical signal is 
displayed. Mark on the shaft of the probe to identify the end point of the crack.  
(3) Slowly remove the probe away from the fastener hole until a 25% FSH vertical 
signal is displayed. Mark on the shaft of the probe to identify the start point of the 
crack. 
(4) Measure the distance between the start and finish points on the shaft of the 
probe; this is the total depth of the crack.

### Page 27

CL-215 
CL-215T 
 
Page 25 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
(5) Measure the distance between the start point and the center of the coil; this is 
the depth of the crack. 
e. To determine the direction of indicated cracks (bore and countersink) relative to the 
fastener hole circumference, do the following: 
(1) With the probe inserted and rotating in the fastener hole, turn the drive unit until 
the crack signal is displayed at 180° on the screen display. 
The crack location is relative to the position of the drive unit (refer to the 
sensitivity calibration step) as shown if Figure 5. 
f. Do the acceptance and rejection criteria as follows: 
(1)  Refer to Note below.  Any distinct vertical signal (or corrosion related “noise” 
signal) that is not attributed to edges, ferrous contamination or poor fastener hole 
condition which is near (or equal to or greater than) 50% of the response from 
the 0.040−inch (1.02−mm) deep EDM notch as shown in Figure 2 is classified as 
a crack (or corrosion) indication and is cause for rejection. 
NOTE: It is highly recommended to establish the CLEAN (i.e., new hole 
without defect) hole signal under the existing setup of the calibrated 
Eddy Current inspection equipment, and any hole with distinct vertical 
signal or corrosion related “noise” signal (that is not attributed to edges, 
ferrous contamination or poor fastener hole condition) above the 
CLEAN hole signal level should be rejected. This will capture/rectify 
cracks or corrosion less than 0.020” long/deep. The CLEAN hole signal 
level can be established from the existing Calibration Reference 
Standard block (in a clean hole), or from a newly drilled/ream hole with 
the equivalent hole diameter on a multiple-layer-sheet block simulating 
the actual structural material and hole size being inspected, taking into 
account the edge surface effect. 
(2) If a crack is detected, determine its length and location with Eddy Current 
surface scan in accordance with Section II.A.4, and/or estimate the crack length 
using the vertical signal level of the BHEC rotating probe (smaller cracks in 
fastener holes) compared against the response from the 0.040−inch (1.02−mm) 
deep EDM notch. If cracks are found on lower skin, the drag angle shall be 
removed (if not yet) for evaluation of crack sizes and subsequent repair or 
replacement. 
(3) Using the inspection Reply Form provided with this Service Bulletin, record the 
results, taking note of the type and location of any damage indication. Submit all 
your findings to VAL Technical Support. 
NOTE: A photographic record of the damage attached to the inspection Reply 
Form is highly recommended.

### Page 28

CL-215 
CL-215T 
 
Page 26 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
4. Do the Eddy Current surface scan inspection as follows: 
NOTES: 
(1) The Eddy Current Surface Scan (ECSS) inspection is applicable to the drag angle 
(along the bending radius) and all fastener holes in which crack(s) indication is 
observed.  
(2) To determine the crack length in fastener holes on the lower skin, ECSS must be 
done from both the interior and exterior accessible surface (i.e., except the mating 
surfaces between the skin and the stringers or wing spar lower caps). If cracks are 
found in the fastener holes on wing lower skin, the drag angle will need to be 
removed (if no yet) for incorporating repairs or replacement. 
(3) To determine the crack length in fastener holes on the wing front/rear spar web/cap 
or fuselage vertical frame, perform ECSS on accessible surface and submit your 
findings to VAL Technical Support for help. 
Equipment and Materials: 
DESCRIPTION PART NO./  SPECIFICATION UNITS PER ASSEMBLY ITEM  NO. 
Eddy Current Instrument, 
Impedance-Plane Type 
Hocking Phasec 2200 
or equivalent 
1 − 
Coaxial cable, BNC to 
Microdot 
Commercial 1 − 
Calibration Reference 
Standard made from 
aluminum alloy (29−32% 
IACS) containing 0.008 in. 
(0.20 mm), 0.020 in. 
(0.51 mm), and a 0.040 
in. (1.02 mm) deep 
electrical discharge 
machined (EDM) notches. 
AL29−32 (see Figure 7) 
or equivalent 
 
1 − 
45° Surface probe, 50 kHz to 
500 kHz frequency, Fe/NFe, 
absolute, shielded, 0.125−in. 
(3.175−mm) diameter, 6.0−in. 
(152.4−mm) length, 0.500−in. 
(12.7 mm) drop. 
Techna NDT 
PEN45−6  
or equivalent 
1 − 
Non−Conductive Tape Commercial AR − 
Ruler or straight edge 
(non−conductive) 
Commercial 1 − 
Circle Template 
(non−conductive) 
Commercial 1 − 
NOTE: If equivalent equipment is used, it must satisfy the requirement of the task and 
resolve the reference notches in the calibration reference standard at the 
required level of resolution and sensitivity.

### Page 29

CL-215 
CL-215T 
 
Page 27 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
a. For each inspection location, make sure that the surfaces are clean and that the 
primer and paint finishes are in good condition. If necessary, remove any damaged 
finishes. Refer to PSP 297, Chapter 51. 
Refer to Figure 6, Figure 7, and Figure 8 
b. Calibrate the equipment as follows 
(1) Connect the probe with the coaxial cable to the eddy current instrument. 
(2) Turn the instrument [ON]. Adjust and set the instrument controls as shown in 
Figure 6 Calibration Data, Instrument Settings. 
(3) Put the probe (coil) tip perpendicular to the surface of AL29−32 Calibration 
Reference Standard (CRS) away from the edges and the EDM notches. Refer to 
Figure 7. 
(4) Balance the eddy current instrument. Adjust the instrument [PHASE] control to 
obtain a horizontal lift−off signal moving from RH−to−LH side (with increasing 
lift−off) across the screen display. 
(5) Move the probe (coil) tip across the 0.040−inch (1.02−mm) deep EDM notch, 
and adjust the instrument sensitivity [GAIN] to obtain an amplitude signal as 
shown in Figure 6. 
(6) Differentiate between the EDM notch and the edge signals by moving the probe 
over the edge of the reference standard. The signal obtained from the edge shall 
slant−off towards the upper LH quadrant as shown in Figure 6. 
(7) If the inspection area is painted, carry out the lift−off compensation prior to 
inspection, as follows: 
(a) Put the probe (coil) tip perpendicular to the inspection surface. Do not 
balance the instrument. 
(b) Compare the screen displays between the operating point on the inspection 
surface and the balance point on the CRS. 
(c) If the operating point on the inspection surface matches the balance point on 
the CRS, no compensation for paint thickness is required. 
(d) If the operating point on the inspection area does not match the balance 
point on the CRS, but has moved to the LH side, compensation for the paint 
thickness is required. Do as follows: 
– Slide the probe (coil) tip across the 0.040−inch (1.02−mm) deep EDM 
notch covered with tape on the CRS. 
– Adjust the [GAIN] to obtain an eddy current amplitude signal from the 
0.040−inch (1.02−mm) deep EDM notch as shown in Figure 6.

### Page 30 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
Calibration Data
Instrument Settings  Screen Display
Mode  ABS, Ch 1  EDGE SIGNAL  SIGNAL FROM 0.040 in (1,02 mm)  EDM NOTCH
Display  XY
View  Ch 1  100%
Ch 1 Frequency  500 kHz
Ch 1 Phase  301.0°
Ch 1 Gain  46 dB  80%
Ch 1 X:Y  Х - 8 dB  FSH
Hi - Pass  DC
Lo - Pass  200 Hz
Balance Load  0% -
X - Pos  40
Y - Pos  -40  LIFT-OFF SIGNAL  BALANCE POINT
CALIBRATION DATA
FIGURE 6
Page 28 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 31 (OCR)

CL-215  VIKING*
CL-215T
MODEL CL-215-1A10
MODEL CL-215-6B11
ALERT SERVICE BULLETIN
0.005 in. + 0.000/-0.002 in.
(0,127 mm + 0,000/-0,051 mm)
WIDE × 1.50 in. (38,10 mm)
LONG EDM NOTCH
(TYPICAL)
1.00 in.  (2,54 cm)
3.75 in.  (9,53 cm)  0.75 in.  (19,05 mm)
0.75 in.  (19,05 mm)
008
ZЕ-6Z 7V  024
1.50 in.  (3,81 cm)  .042  1,02 mm)  0.04 in.  DEPTH  DEPTH  (0,51 mm)  0.02 in.  (0,20 mm)  DEPTH  0.008 in.
(6,35 mm)  0.25 in.
CALIBRATION REFERENCE STANDARD AL29-32
FIGURE 7
Page 29 of 46  ATA Ref. 57-30
Rev NC 11-DEC.-2015  Service Bulletin 215-A568
Rev 4 22-JAN.-2019

### Page 32

CL-215 
CL-215T 
 
Page 30 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
 
 
 
 
 
NOTE: Circular scan with draftsman’s circle template is not required to determine surface crack size. 
 
 
 
 
TYPICAL CIRCULAR SCAN PATH AND PROBE POSITION  
FIGURE 8

### Page 33

CL-215 
CL-215T 
 
Page 31 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
c. Perform the surface scan as follows: 
(1) Place the probe (coil) tip on the inspection surface, adjacent to the fastener hole 
to be inspected. Refer to Figure 8. 
(2) Rebalance the instrument. If necessary, adjust instrument [PHASE] control to 
obtain a horizontal lift−off signal moving from RH−to−LH across the screen 
display. 
(3) Make a scan perpendicular (90°) to crack orientation at the identified crack 
location in a zig-zag pattern moving away from crack initiating point (e.g., hole 
bore edge) to determine the crack tip. Mark the crack tip with a thin sharpie pen, 
then, measure and record the crack location, orientation and length. 
NOTE: It is highly recommended to establish the CLEAN (i.e., away from the 
EDM notch area on the calibration standard) surface scan response 
under the existing setup of the calibrated equipment, and any distinct 
response (that is not attributed to edges effect, abrupt change in 
geometry, localized variation in conductivity, permeability or other 
non−relevant factors) above the CLEAN surface response should be 
considered as the continuation of the crack while identifying the crack 
tip.  
(4) Repeat this technique on each and every identified inspection location. 
(5) If surface defects (scratches, gouges, nicks, scores, dents, surface pitting, or 
other surface damage) are present on the wing lower skin, lower stringers, 
front/rea spar caps/web and vertical fuselage frames in the inspection area 
specified in Figure 1, scan around all surface defects for potential cracks. Report 
any surface damage and associated crack (if any) to VAL Technical Support for 
further instruction or refer to applicable SRM. 
(6) Also scan all drag angles for chordwise cracks along the bending radius. 
d. Do the evaluation of indications as follows: 
(1) Any distinct vertical deflection signal that occurs over a short scan distance (one 
probe tip diameter) is considered a suspect indication and is cause for further 
investigation. 
(2) Make sure the indication is not caused by edge effect, abrupt change in 
geometry, localized variation in conductivity, permeability or other non−relevant 
factors. 
(3) Evaluate all suspect crack indications by comparing their phase angle, amplitude 
and shape to the calibration standard EDM notch signal. 
e. Do the acceptance and rejection criteria as follows: 
(1) Refer to Note below. Any distinct vertical signal that is not attributed to edge 
effect which is near (or equal to or greater than) 50% of the response from the 
0.040−inch (1.02−mm) deep EDM notch as shown in Figure 6 is classified as a 
crack indication and is cause for rejection. 
NOTE: It is highly recommended to establish the CLEAN surface scan 
response (i.e., away from the EDM notch area on the calibration 
standard) under the existing setup of the calibrated equipment, and any

### Page 34

CL-215 
CL-215T 
 
Page 32 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
inspected surface with distinct response or corrosion related “noise” 
response (that is not attributed to edges effect, abrupt change in 
geometry, localized variation in conductivity, permeability or other 
non−relevant factors) above the CLEAN surface response should be 
rejected. This will capture and rectify cracks or corrosion less than 
0.020” long/deep. 
(2) If a surface crack is detected, determine its length and location in accordance 
with Paragraph II.A.4.c.(3), and go to Paragraph II.A.4.e.(3). 
If no crack is found and if it is preferred, optional preventative REO 215-57-V022 
(Revision NC or later) can be installed at this stage, then go to Section II.A.5 
(contact VAL Technical Support for REO 215-57-V022). 
(3) Record and report results in accordance with company guidelines and policies. 
Refer to Figure 1.  
5. Structural Gap Check between the Drag Angles and the Wing Lower Skin 
The structural gap check and the installation of the LH side drag angles is described. 
The structural gap check and installation of the RH side drag angles are similar. 
a. If the drag angles are not removed, visually check the mating surface on both LH 
and RH sides between the wing lower skin and the drag upper flanges (along its 
inboard and outboard edges) for possible gaps. Remove fillet sealant along the drag 
angle upper flanges as required. Use suitable lighting and visual aids such as 
mirrors, magnifying lenses, and/or borescope as required. Then, go to Step 
II.A.5.d.(1) below. 
b. If the drag angles are removed and prior to fitting the drag angles back to their 
installation positions, all surface defects (if any) on the wing lower skin and drag 
angles shall be removed (all protruding material around gouges, nicks, scores, 
scratches or dents shall be blended flush with the skin/drag angle surfaces). Apply 
Alodine Class 1A solution MIL-C-81706 and two (2) coats of Epoxy Primer to all 
bare metal surfaces.  
c. Fit the serviceable LH side drag angles into position under the LH side of the wing 
using temporary fasteners installed through the drag angles and into the fuselage 
side skin only. 
d. Check for gaps between the contours of the upper flange of the drag angle and the 
wing lower skin. 
(1) Using the Reply Form provided with this Service Bulletin, record the results, 
taking note of any areas of gap or distortion and the associated dimensional 
information. Submit all your findings to VAL Technical Support. 
NOTE: A photographic record of the gap condition attached to the inspection 
Reply Form is highly recommended. 
e. Repeat above structural gap check Step II.A.5.a to II.A.5.d between the RH side 
drag angles and wing lower skin.

### Page 35

CL-215 
CL-215T 
 
Page 33 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
6. Installation of Drag Angles 
a. Fit the LH side drag angles into position under the wings using temporary fasteners. 
b. Measure the fastener holes diameters for Hi-Lite fasteners to determine if oversize 
fasteners will be required (interference fit). In addition, measure and confirm the 
required grip lengths for the fasteners. 
Drill and ream affected fastener holes to the new dimensions as necessary. Refer to 
PSP 497 Chapter 51 (interference fit). 
Verify that a minimum of 1.8D (D = fastener hole diameter) edge distance can be 
maintained. 
If these limitations cannot be achieved, contact and provide VAL Technical Support  
with the details for further instructions. 
NOTES: 
(1) The drag angles will be installed using Hi−Lite fasteners and KFN nuts later. 
(2) Do not enlarge or rework the fastener holes before collecting and sending the 
inspection results back to VAL Technical Support. 
(3) If fastener size other than what are specified in Figure 1 Sheet 5 is required, 
contact VAL Technical Support. 
c. Refer to Figure 1 (Sheet 1, 2 and 5) and PSP 297 Chapter 51, and do as follows: 
(1) Remove the temporary fasteners and the drag angles. 
(2) Remove any burrs and break sharp corners 0.015” radius (unless otherwise 
specified). Apply Alodine Class 1A solution MIL-C-81706 and two (2) coats of 
Epoxy Primer to all bare metal on the drag angles or the mating surfaces on the 
fuselage structures and wing skins per PSP 297 Chapter 51–52–16. Do not 
apply primer into hole bores. 
If necessary, apply one coat of BAMS 565−009 polyurethane top coat (colour to 
match existing finish) to the affected areas of the fuselage and wing skins. 
(3) Apply Pro-Seal-870C, or equivalent sealant per PSP 297, Chapter 51–55–00, to 
the contact surface of the drag angles. 
Refer to Figure 1 and PSP 297 Chapter 51 
(4) Install the Hi-Lite fasteners that secure the drag angles to the aircraft structure 
and at other locations shown in Figure 1 per PSP 297, Chapter 51–43–19. Wet 
install fasteners per PSP 297, Chapter 51–55–00. 
NOTE:  If fastener size other than what are specified in Figure 1 Sheet 5 is 
required, contact VAL Technical Support. 
(5) Apply a bead of Pro-Seal-870C sealant to the edges of the drag angles in 
accordance with PSP 297, Chapter 51–55–00. 
d. If necessary, apply one coat of polyurethane top coat (colour to match existing 
finish) to the drag angles and surrounding fuselage and wing skin area in 
accordance with PSP 297, Chapter 51–52–16.

### Page 36

CL-215 
CL-215T 
 
Page 34 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
e. Repeat Step II.A.6.a to II.A.6.d for the RH drag angles. 
7. Install Hi-Lite and Hi-Lok fasteners shown in Figure 1 Sheet 3, 4 and 5 as follows: 
a. Measure the fastener holes diameters for Hi-Lite and Hi-Lok fasteners to determine 
if oversize fasteners will be required (interference fit). In addition, measure and 
confirm the required grip lengths for the fasteners. 
Drill and ream affected fastener holes to the new dimensions as necessary. Refer to 
PSP 497 Chapter 51 (interference fit). 
Verify that a minimum of 1.8D (D = fastener hole diameter) edge distance can be 
maintained. 
If these limitations cannot be achieved, contact and provide VAL Technical Support 
with the details for further instructions. 
NOTES:  
(1) Do not enlarge or rework the fastener holes if the fastener hole quality and size 
meet the requirement. 
(2) If fastener size other than what are specified in Figure 1 (Sheet 3, 4, and 5) is 
required, contact VAL Technical Support. 
b. If existing fastener hole is oversized as shown in Figure 1 Sheet 3, 4 and 5, remove 
any burrs and break sharp corners 0.015” radius (unless otherwise specified). Apply 
one coat of Alodine Class 1A solution MIL-C-81706 and two (2) coats of Epoxy 
Primer to all bare metal on the fuselage and wing structure per PSP 297 Chapter  
51–52–16 as required. Do not apply primer into hole bores. 
c. Install the Hi-Lite and Hi-Lok fasteners per PSP 297, Structural Repair Manual, 
Chapter 51–43–19 and 51−43−16. Wet install fasteners per PSP 297, Chapter  
51–55–00.  
8. At a suitable location in or near the inspection location on the wing lower skin and at the 
vertical fuselage frame to wing joint area, apply the identification marking “SB 215−A568 
Revision 4 Section II.A” with the date. Refer to PSP 297, Chapter 51. 
9. Close out 
a. Do an inspection for Foreign Object Debris (FOD) in the wing interior. Ensure that 
No. 2 fuel cell bays are clean and free of any such FOD. 
b. Install the LH and RH side No. 2 fuel cell. 
For CL-215 Aircraft, refer to PSP 292 Chapter 28. 
For CL-215T Aircraft, refer to PSP 392 Chapter 28. 
B. Replace NAS1242AD Rivets (Specified in Previous Revisions of This SB, One-Time) 
This Section is applicable to aircraft complied with Revision 3 (or earlier) of this SB. Perform 
one-time replacement of the NAS1242AD rivets as follows.

### Page 37

CL-215 
CL-215T 
 
Page 35 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
NOTES:  
(1) At the same time while replacing the NAS1242AD rivets, the all rivet holes and other 
inspection locations (identified for inspection in Section II.A.1, Revision 4 of this SB) 
shall be inspected. 
(2) If standard SRM or son-standard repairs were installed on wing lower skin or front/rear 
spar lower cap/web, or any of these parts were replaced in the inspection areas 
specified in Revision 4 of this SB, the structural configuration, fatigue crack prone 
location and/or the accumulated flight time (FH, WD, TOC) on the concerned 
component(s) would be changed. This condition may require an AMOC against 
applicable ADs associated with Revision 4 of this SB and all other related SBs. 
Contact VAL Technical Support for further inspection instructions to support AMOC 
application to local airworthiness authority as required. Provide repair/replacement 
details as listed in Section II.C of this SB when contacting VAL Technical Support. 
(4) It is also optional to install the preventative REO 215-57-V022 (Revision NC or 
later), if so preferred and no defects are found from following inspections (contact 
VAL Technical Support for REO 215-57-V022). 
Refer to Section II Note (for applicable maintenance manual) and Figure 1. 
1. Support the entire wing weight (including engines and accessory components and fluid) 
by jacking up the wing with suitable cradles positioned at WS 91.2L/R and/or 212L/R 
under the ribs. This is to “zero-load” the wing to fuselage joints. Refer to applicable 
maintenance manuals for the wing weight (depending on the wing condition, it may be in 
the order of 22,500 lbs. with zero fuel). 
a. Remove the LH and RH side No. 2 fuel cell. 
For CL-215 Aircraft, refer to PSP 292 Chapter 28.  
For CL-215T Aircraft, refer to PSP 392 Chapter 28. 
b. Remove NAS1242AD rivets between FS 388.86 and 434.836 from the front and rear 
drag angles 215−30031 from both the LH and RH sides as shown in Figure 1 Sheet 
1 and Sheet 2. Take care to avoid damaging the fastener holes prior to inspection. 
Refer to PSP 297, Chapter 51. 
c. Using a suitable bristle hole brush to clean fasteners hole bore, as required, and do 
BHEC inspection of the open holes using a rotating Probe, in accordance with 
Section II.A.3. 
d. If no defect is found, install the Hi−Lite fasteners as shown in Figure 1 (Sheets 1, 2 
and 5) in accordance with Section II.A.6 (ignore Step II.A.6.a.).  
If defect is detected, contact VAL Technical Support for disposition. 
2. If necessary, apply one coat of polyurethane top coat (colour to match existing finish) to 
the drag angles and surrounding fuselage and wing skin area in accordance with PSP 
297, Chapter 51–52–16. 
3. At a suitable location in or near the inspection area on the wing lower skin, apply the 
identification marking “SB 215−A568 Revision 4, Section II.A, and/or Section II.B”, as 
applicable with the date. Refer to PSP 297, Chapter 51.

### Page 38

CL-215 
CL-215T 
 
Page 36 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
4. Close out 
a. Do an inspection for Foreign Object Debris (FOD) in the wing interior. Ensure that 
No. 2 fuel cell bays are clean and free of any such FOD. 
b. Install the LH and RH side No. 2 fuel cell. 
For CL-215 Aircraft, refer to PSP 292 Chapter 28. 
For CL-215T Aircraft, refer to PSP 392 Chapter 28. 
C. Identify Existing Standard SRM and Non-Standard Repairs on Wing Box between WS 355L 
and WS 355R 
1. Identify and report existing standard SRM and non-standard repairs (other than 
Allowable Damage) incorporated on wing box structures between WS 355L and WS 
355R as follows: 
a. Identify specific reference documents of repairs installed on wing front/rear spar 
webs and upper/lower caps, upper/lower skins, upper/lower stringers and ribs. 
b. Indicate damage type (crack, corrosion or other), damage size (crack length, 
orientation, corrosion depth, etc.) and damage location (WS, FS, WL, etc.). 
c. Indicate when the repair was incorporated (repair date, WD, LL, TOC). 
d. Whether initial/repeat inspections are specified for each repair (yes or no). 
e. If yes, provide specified inspection intervals and inspection technique. 
f. If the damaged part was replaced, provide damage type (crack, corrosion or other), 
damage size (crack length, orientation, corrosion depth, etc.), damage location (WS, 
FS, WL, etc.), as well as when the replacement was completed (replacement date, 
WD, LL, TOC). 
g. Using the inspection Reply Form provided with this Service Bulletin (or separate 
sheets) to report existing standard SRM and non-standard repairs/replacements on 
wing box structures to VAL Technical Support. 
NOTE: Existing repairs/replacements may be identified based on visual inspection 
and/or the aircraft maintenance records. 
D. Recording 
When this Service Bulletin is completed, make the entry in the aircraft log book (completed 
SB 215−A568 Revision 4, Section II.A, and/or Section II.B, and/or Section II.C, as 
applicable) and send back the attached SB 215-A568 REPLY FORM to VAL Technical 
Support via email to technical.support@vikingair.com or via fax to 1-403-295-8888.

### Page 39

CL-215 
CL-215T 
 
Page 37 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
III. Material Information and Tooling 
This Service Bulletin contains no kit.   
A. Equipment and Materials to Obtain Locally 
The following equipment and materials, or their equivalents, are necessary to do this Service 
Bulletin. You can buy or obtain their use locally: 
DESCRIPTION PART NO./NAME SPECIFICATION QUANTITY 
Eddy Current Instrument, 
Impedance-Plane Type 
Hocking 
Phasec 2200 or 
equivalent See 
Note [3] 
Commercial 1 
Mini Drive Unit Hocking 
33A100 
or equivalent 
See Note [3] 
Commercial 1 
Cable for Mini Drive Unit Hocking 
33A103  
or equivalent 
See Note [3] 
Commercial 1 
Calibration−Reference 
Standard, conductivity 
value between 39% and 
45% IACS that contains 
various hole sizes with 
0.040 − inch (1.02 − mm) 
deep electrical discharge 
machined (EDM) notches. 
BA CRS 
BH7475−T7351 
or equivalent 
See Note [3] 
Commercial 1

### Page 40

CL-215 
CL-215T 
 
Page 38 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
Equipment and Materials to Obtain Locally − cont’d 
DESCRIPTION PART NO./NAME SPECIFICATION QUANTITY 
Rotating Bolt − Hole Probe, 
100 kHz − 2.0 MHz frequency, 
adjustable, 0.125 to 
0.156−inch, adjustable 
diameter, 2.0−inch length 
Techna NDT HRY 
0.125 to 0.156  
or equivalent 
See Note [3] 
Commercial 1 
Rotating Bolt − Hole Probe, 
100 kHz − 2.0 MHz frequency, 
adjustable, 0.156 to 
0.187−inch, adjustable 
diameter, 2.0−inch length. 
Techna NDT HRY 
0.156 to 0.187  
or equivalent  
See Note [3] 
Commercial 1 
Coaxial cable, BNC to 
Microdot 
Commercial 
See Note [3] 
Commercial 1 
Calibration Reference 
Standard made from 
aluminum alloy (29−32% 
IACS) containing 0.008 in.  
(0.20 mm), 0.020 in.  
(0.51 mm), and a 0.040 in. 
(1.02 mm) deep electrical 
discharge machined (EDM) 
notches. 
BA CRS AL29−32 
or equivalent 
See Note [3] 
Commercial 1 
45° Surface probe, 50 kHz to 
500 kHz frequency, Fe/NFe, 
absolute, shielded, 0.125−in. 
(3.175−mm) diameter, 6.0−in. 
(152.4−mm) length, 0.500−in 
(12.7 mm) drop. 
Techna NDT 
PEN45−6  
or equivalent 
See Note [3] 
Commercial 1 
Non−Conductive Tape Commercial Commercial AR 
Ruler or straight edge 
(non−conductive) 
Commercial Commercial 1 
Circle Template 
(non−conductive) 
Commercial Commercial 1 
Explosion Proof Light Commercial  Commercial 1 
Magnifying lenses, 10X or 
better 
Commercial Commercial 1 
Borescope with 10X 
magnifying lens (and 
illumination if available) 
Commercial Commercial 1

### Page 41

CL-215 
CL-215T 
 
Page 39 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
Equipment and Materials to Obtain Locally − cont’d 
DESCRIPTION PART NO./NAME SPECIFICATION QUANTITY 
Hi-Lite Pin Commercial HST10AG−(6)−( ) [1] 
HST110AG−(6)−( ) [1] 
AR 
AR 
KFN Nut Commercial KFN587−(6) 
KFN600−(6) 
KFN673−(6) 
AR 
AR 
AR 
Hi-Lite Pin Commercial HST12AG−(6)−( ) [1] 
HST112AG−(6)−( ) [1] 
HST412AG−(6)−( ) [1] 
AR 
AR 
AR 
Hi-Lok Pin Commercial HL32PB−(8)−( ) [1] 
HL36PB−(8)−( ) [1] 
HL136PB−(8)−( ) [1] 
AR 
AR 
AR 
Hi-Lok Collar Commercial HL273-(8) 
HL273-(10) 
AR 
AR 
Hi-Lok Pin Commercial HL32PB−(10)−( ) [1] 
HL36PB−(10)−( ) [1] 
HL136PB−(10)−( ) [1] 
AR 
AR 
AR 
Aliphatic naphtha Commercial TT−N−95 AR 
Solvent, Dry Cleaning Commercial P−D−680 A/R 
Alodizing Solution Commercial MIL-C-81706 A/R 
Epoxy Primer, fluid  
resistant 
Commercial BAMS 565−008 
or equivalent 
A/R 
Polyurethane Top Coat 
(colour to match existing 
finish) 
Commercial BAMS 565−009 
or equivalent 
A/R 
Faying Surface Type 
Sealant 
Pro Seal 870 Type 
IV  
or equivalent 
BAMS 552-005 Type IV 
or equivalent 
A/R 
Beading Type Sealant Pro Seal 870 
Type II 
BAMS 552−005 Type II 
or equivalent 
A/R 
NOTES: [1] Grip length of fastener / nut diameter, to be determined at installation. 
[2] For other equipment and materials, refer to the referenced PSP procedures. 
[3] If equivalent equipment is used, it must satisfy the requirement of the task and 
resolve the reference notches in the calibration reference standard at the 
required level of resolution and sensitivity.

### Page 42

CL-215 
CL-215T 
 
Page 40 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
 
THIS PAGE INTENTIONALLY BLANK

### Page 43

CL-215 
CL-215T 
 
Page 41 of 47  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
SB 215−A568 REPLY FORM 
OPERATOR A/C REGISTRATION NO. A/C SERIAL NO. AIRFRAME HOURS WATER DROPS (INCLUDING WATER LANDINGS OF NON-WATER DROP) LAND LANDINGS  
      
CONTACT PERSON:  PHONE/EMAIL:  
INSPECTION PERFORMED BY:  DATE:  
   INSPECTION 
TYPE 
VISUAL/EDDY 
CURRENT  
CRACKED PARTS, FASTENER HOLE LOCATION, 
ORIENTATION AND SIZE: 
INTERIOR / EXTERIOR, LH / RH, WS, FS, WL, 
SPAR / STRINGER DATUM 
DESCRIPTION 
 
   
   
   
   
   
   
   
   
GAP CHECK DRAG ANGLE − WING LOWER SKIN GAP 
LOCATION  
   
   
Additional Comments (add additional sheet as required): 
  
  
  
  
Please return form via email to technical.support@vikingair.com or via fax to 1-403-295-8888.

### Page 44

CL-215 
CL-215T 
 
Page 42 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
 
THIS PAGE INTENTIONALLY BLANK

### Page 45

CL-215 
CL-215T 
 
Page 43 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
SB 215−A568 REPLY FORM 
OPERATOR A/C REGISTRATION NO. A/C SERIAL NO. AIRFRAME HOURS WATER DROPS (INCLUDING WATER LANDINGS OF NON-WATER DROP) LAND LANDINGS  
      
CONTACT PERSON:  PHONE/EMAIL:  
INSPECTION PERFORMED BY:  DATE:  
   EXISTING 
STANDARD SRM 
AND NON-
STANDARD REPAIR 
– DOCUMENT 
NUMBER 
EXISTING SRM STANDARD AND NON-
STANDARD REPAIRS (OTHER THAN 
ALLOWABLE DAMAGE) INSTALLED ON 
WING STRUCTURAL MEMBERS BETWEEN 
WS 355L AND 355R. PROVIDE DEFECT 
TYPE, SIZE AND LOCATION SUCH AS 
LH / RH, WS, FS, WL 
DESCRIPTION OF REPAIR (INCLUDING REPLACEMENT), TOTAL 
NUMBER OF WATER DROPS (WD), WATER LANDINGS (OF 
NON-WATER DROP, WL), LAND LANDINGS (LL)  
 WING FRONT UPPER CAP – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR UPPER CAP – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING FRONT SPAR LOWER CAPS – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR SPAR LOWER CAPS – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING FRONT SPAR WEB – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR SPAR WEB – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING LOWER SKIN – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING LOWER STRINGER – LH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
   
   
   
Additional Comments (add additional sheet as required): 
  
  
  
  
Please return form via email to technicalsupport@vikingair.com or via fax to 1-403-295-8888.

### Page 46

CL-215 
CL-215T 
 
Page 44 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
 
THIS PAGE INTENTIONALLY BLANK

### Page 47

CL-215 
CL-215T 
 
Page 45 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
SB 215−A568 REPLY FORM 
OPERATOR A/C REGISTRATION NO. A/C SERIAL NO. AIRFRAME HOURS WATER DROPS (INCLUDING WATER LANDINGS OF NON-WATER DROP) LAND LANDINGS  
      
CONTACT PERSON:  PHONE/EMAIL:  
INSPECTION PERFORMED BY:  DATE:  
   EXISTING 
STANDARD SRM 
AND NON-
STANDARD 
REPAIR – 
DOCUMENT 
NUMBER 
EXISTING STANDARD SRM AND NON-
STANDARD REPAIRS (OTHER THAN 
ALLOWABLE DAMAGE) INSTALLED ON WING 
STRUCTURAL MEMBERS BETWEEN WS 355L 
AND 355R. PROVIDE DEFECT TYPE, SIZE AND 
LOCATION SUCH AS 
LH / RH, WS, FS, WL 
DESCRIPTION OF REPAIR (INCLUDING REPLACEMENT), TOTAL 
NUMBER OF WATER DROPS (WD), WATER LANDINGS (OF 
NON-WATER DROP, WL), LAND LANDINGS (LL)  
 WING FRONT UPPER CAP – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR UPPER CAP – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING FRONT SPAR LOWER CAPS – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR SPAR LOWER CAPS – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING FRONT SPAR WEB – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING REAR SPAR WEB – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING LOWER SKIN – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
 WING LOWER STRINGER – RH 
CRACK___CORROSION____OTHER____ 
WS_____FS_____WL_____ 
REPAIR/REPLACE DATE:           WD=           WL=           LL= 
INSPECTION SPECIFIED?   YES ________    NO _______ 
IF YES, PROVIDE INSEPCTION INTERVALS AND TECH NIQUE 
   
   
   
Additional Comments (add additional sheet as required): 
  
  
  
  
Please return form via email to technical.support@vikingair.com or via fax to 1-403-295-8888.

### Page 48

CL-215 
CL-215T 
 
Page 46 of 46  ATA Ref. 57-30 
Rev NC 11-DEC.-2015 Service Bulletin 215-A568 
Rev 4  22-JAN.-2019 
MODEL CL-215−1A10 
MODEL CL-215-6B11 
ALERT SERVICE BULLETIN 
 
THIS PAGE INTENTIONALLY BLANK

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
