# Viking Air Alert Service Bulletin V2/0007: No revision named

- Rights: © Viking Air. Filed by the FAA in regulations.gov docket FAA-2015-0096; AD 2015-02-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Viking Air Alert Service Bulletin V2/0007](https://openairdocs.org/service-documents/viking/v2-0007.md)
- Title as filed: U.S. DOT/FAA - V2-0007 RevNC Final (2)
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/25/f2/25f289317f7ca309e114f8e209ccb822f2b230fb77826c4adebfee0a841d60f2
- Page: https://openairdocs.org/service-documents/viking/v2-0007/file/25f289317f7c

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

1959 deHavilland Way. 
Sidney, B.C. 
Canada V8L 5V5 
Tel: (250) 656 - 7227 
 
DHC-2 
Beaver 
  
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’   Page 1 of 6 
 
ALERT SERVICE BULLETIN 
 
 ATA SYSTEM: 5510 NUMBER: V2/0007 
 
 
I. PLANNING INFORMATION 
A. Effectivity 
Aircraft Affected:  All DHC-2 aircraft. 
 
NOTE: The instructions in this Service Bulletin are only applicable to the systems and parts 
installed at the time of delivery on the aircraft or as changed by Viking Service 
Bulletin(s).  Before you do this bulletin, examine all STC or equivalent action changes to 
make sure this bulletin can be completed. 
B. Reason 
A DHC-2 horizontal stabilizer attach bracket has been found with two (2) MS21042 
locknuts broken.  Upon further investigation, Viking has found a quality issue with the 
locknuts.  (See Figure 3). 
C. Description 
Some MS21042 Locknuts have been identified as being affected by a manufacturing 
issue, making them susceptible to premature failure due to cracking.  This issue had 
previously been identified amongst other aircraft manufacturers and corrective action 
publications had been distributed.  The fact that Viking has recently been supplied with a 
quantity of sub-quality locknuts, indicates that sub-quality parts continue to be available.   
Due to the recent DHC-2 horizontal stabilizer bracket attach locknut issue, the following 
inspection / replacement shall be completed for all DHC-2 aircraft. 
SUBJECT:  INSPECTION AND/OR REPLACEMENT OF MS21042 LOCKNUT 
IN HORIZONTAL STABILIZER (P/N C2TP1A)

### Page 2

ALERT SERVICE BULLETIN V2/0007 
 
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’    Page 2 of 6 
D. Compliance 
All DHC-2 operators shall  inspect their aircraft within 48 hours of receiving  this Service 
Bulletin.  If  MS21042 locknuts are found, they must be replaced  by MS21044 locknuts 
before further flight. 
E. Approval 
The technical content of this Service Bulletin has been approved under the authority of 
Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) 04-V-02. 
F. Manpower 
Approximately 1 hour labour will be required to perform the inspection of the locknuts . 
Approximately 12 hours is required if locknuts must be replaced with new ones. 
NOTE: Visual inspection labour may be considerably more if stabilizer assembly must 
be removed to properly inspect locknuts. 
G. Weight and Balance 
Not affected. 
H. Electrical Load Data 
Not affected. 
I. Publications Affected 
None. 
J. References 
This Service Bulletin is self-contained.  No additional drawing or documents are required 
to implement the Accomplishment Instructions. 
Note: For more information please contact: 
Viking Air Limited FAX: 250-656-0673 
Technical Support Telephone Numbers: 
1959 de Havilland Way Regional: 250-656-7227 
Sidney, British Columbia North America: 1-866-49-ATLAS 
Canada, V8L 5V5 International: 1-800-6727-6727 
technical.support@vikingair.com

### Page 3

ALERT SERVICE BULLETIN V2/0007 
 
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’    Page 3 of 6 
 
II. ACCOMPLISHMENT INSTRUCTIONS 
A. Preparing for Inspection 
1. Remove tailcone section as per PSM 1-2-2 Sec. 2.16; 
2. If visual inspection is impeded in any way, remove stabilizer assembly as per PSM 1-
2-2, Sec. 2.18.1. 
B. Inspection Procedures 
1. Using a flashlight, visually inspect quantity six (6) locknuts (as indicated in Figure 1) 
for type installed: 
a) If the installed locknuts are NOT MS21042 (ref. Figure 2A, 2B, 2C for visual 
aid of possible locknuts installed in this application) skip to Step II. D; 
b) If the installed locknuts are MS21042 (ref. Figure 2D for visual aid), continue 
to Step II. C. 
C. Replacement of Affected Locknuts 
1. Remove stabilizer assembly as per PSM 1-2-2, Sec. 2.18.1; 
2. Remove affected locknuts; 
NOTE: if locknut is completely missing, inspect area for pieces of broken locknut to 
eliminate Foreign Object Damage (FOD) potential. 
3. Install new MS21044 locknuts (IAW para III. A. table) as per standard practices; 
NOTE: Ensure a minimum of two (2) threads on the attach bolts are visible when 
the locknut is installed. 
D. Close-Out 
1. Re-install stabilizer assembly per PSM 1-2-2, Sec. 2.18.3; 
2. Re-install tailcone as per PSM 1-2-2, Sec. 2.16.2. 
3. Inform Viking Technical Support of any cracked locknut findings (See I.J. 
References) 
E. Recording 
After completion of activities make the following entry in the aircraft log book: “Service 
Bulletin No. V2/0007 – INSPECTION OR INSPECTION/REPLACEMENT OF MS21042 
LOCKNUT IN HORIZONTAL STABILIZER (P/N C2TP1A) has been incorporated”.

### Page 4

ALERT SERVICE BULLETIN V2/0007 
 
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’    Page 4 of 6 
III. MATERIAL INFORMATION AND TOOLING 
A. Material Information (Parts Required Per Aircraft) 
Old Part No. Replacement Part No. 
MS21042-3 MS21044N3 
MS21042-4 MS21044N4 
B. Material Information 
None 
C. Tooling – Price and Availability 
 Standard aviation hand tools 
 Flashlight 
 Mirror

### Page 5

ALERT SERVICE BULLETIN V2/0007 
 
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’    Page 5 of 6 
IV. DRAWINGS AND TABLES 
 
FIGURE 1 – MS21042 LOCKNUT LOCATION 
LOCKNUT LOCATION

### Page 6

ALERT SERVICE BULLETIN V2/0007 
 
 
29-April-2013 A.S.B. V2/0007 
Revision ‘NC’    Page 6 of 6 
   
       
  
FIGURE 2A – AN364 LOCKNUT FIGURE 2B – AN 365 LOCKNUT     FIGURE 2C – MS21044 LOCKNUT 
 
 
FIGURE 2D – MS21042 LOCKNUT (ALERT SERVICE BULLETIN SUBJECT) 
 
 
FIGURE 3 – DISCREPANT MS21042 LOCKNUT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
