# Viking Air Service Bulletin V6/0063: Revision A

- Rights: © Viking Air. Filed by the FAA in regulations.gov docket FAA-2022-0284; AD 2022-11-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Viking Air Service Bulletin V6/0063](https://openairdocs.org/service-documents/viking/v6-0063.md)
- Title as filed: Viking DHC-6 Service Bulletin V6-0063 Rev A
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/a6/d6/a6d6f81626bbfa0693c00ef4a6affec3bfcdf6dae2d5b03d35ba3d8a9dc0d68c
- Page: https://openairdocs.org/service-documents/viking/v6-0063/file/a6d6f81626bb

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 of 2 ATA Ref. 76-03 
01-February-2021
Service Bulletin V6/0063 
SERVICE BULLETIN TRANSMITTAL SHEET 
ENGINE CONTROLS – BINDING OF THE FCU PUSH ROD END BEARINGS 
Service Bulletin No.: V6/0063 Date of Original Issue: 07 June 2019 
Revision No: A  Date of Issue: 01 February 2021 
This Service Bulletin is to notify operators of reports of binding of the MOD 6/2347 Fuel Control Unit 
(FCU) push rods, P/N C6CE1398-7.  
NOTE 1: NEW ACTIONS ARE ADDED AT REVISION ‘A’ OF THIS SERVICE BULLETIN. 
NEW ACTIONS ARE REQUIRED ON ALL AIRCRAFT, INCLUDING AIRCRAFT 
INSPECTED TO THE PREVIOUS ISSUE OF THIS SERVICE BULLETIN. 
NOTE 2: This revision supersedes the previous revision of this Service Bulletin. 
NOTE 3: Revision bars in the left margin of this Service Bulletin indicate changes from the  
previous revision. 
This page tr
ansmits Revision ‘A’ of Service Bulletin V6/0063, pages 1 thru 8, dated 01 February 2021. 
This Service Bulletin is re-issued to:  
1.
Extend lubrication requirement of Mod 6/2347 rod ends to all operating environments.
2.
Add special instruction for re-entry into service after a period of non-utilization.
3.
Introduce calendar time threshold to do initial inspections in accordance with (IAW) Sections II.A
and II.B.
4.
Introduce repeat inspections IAW Sections II.A and II.B. until incorporation of Mod 6/2484.
5.
Prohibit Mod 6/2347 FCU push rod Assemblies for future installation.
Remove Service Bulletin V6/0063 Revision ‘NC’ dated 07 June 2019 and replace with attached. 
Previous issues of Service Bulletin V6/0063: 
Initial Issue – Pages 1 thru 8 dated 07 June 2019

### Page 2

Page 2 of 2 ATA Ref. 76-03 
01-February-2021 Service Bulletin V6/0063 
  
THIS PAGE INTENTIONALLY LEFT BLANK

### Page 3

1959 de Havilland Way 
Sidney, B.C. 
Canada V8L 5V5 
Tel: (250) 656 - 7227 
 
 
 
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 1 of 8 
 
DHC-6 
TWIN OTTER 
SERVICE BULLETIN  
 ATA SYSTEM: 76-03 NUMBER: V6/0063  
  
I. PLANNING INFORMATION 
A. Effectivity 
Aircraft Affected: DHC-6 aircraft with MOD 6/2347 or equivalent incorporated (including 
partial incorporation), All Series. 
B. Reason 
There have been reports of binding of the VSC30-3A rod end bearings used in the linkage 
for the fuel control unit push rod assembly P/N C6CE1398-7. The binding of the FCU push 
rod bearings was discovered when one engine failed to return to lower power settings from 
a higher power setting. In at least one case, this was the result of using a lubricant not 
approved for use in the Maintenance Manuals to lubricate the rod end. 
C. Description 
Revision ‘A’ of this Service Bulletin is issued to extend lubrication requirement of Mod 6/2347 
rod ends to all operating environments, and to add repeat inspections. A function check, and 
lubrication is required after a period of non-utilization of the aircraft before re-entry into service.  
Mod 6/2484 FCU push rods and supporting Technical Bulletin No. TB V6/00155 are introduced.   
Mod 6/2347 rod ends (and equivalent) are continued to be inspected and lubricated until 
incorporation of Mod 6/2484.  
NOTE: Mod 6/2347 Lower FCU push rod assemblies, sub-assemblies, rod end 
bearings, and their equivalents are prohibited for future replacement. 
D. Compliance 
NOTE: If Service Bulletin V6/0063 Revision ‘NC’ has already been accomplished, compliance 
item I.D.3 of Revision ‘A’ is considered to be complied with. However, compliance 
items I.D.1, I.D.2, and I.D.4 through I.D.7 are still required. 
Compliance contains 7 requirements: 
1. Following any period of non-utilization of one or more months, before next flight: 
a) Check Mod 6/2347 FCU push rod (C6CE1398-7 and equivalent) for freedom of 
movement in accordance with (IAW) the procedures in Section II.A. 
b) Lubricate the lower FCU push rod ends IAW Section II.C and the applicable 
maintenance manual. 
SUBJECT:  ENGINE CONTROLS – BINDING OF THE FCU PUSH ROD END BEARINGS

### Page 4

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 2 of 8 
2. If lower FCU push rod ends have not been previously lubricated IAW Service Bulletin V6/0063 
Revision ‘NC’, within seven (7) days or before next flight, whichever occurs later, lubricate the 
lower FCU push rods IAW Section II.C and the applicable maintenance manual.  
3. If not already accomplished IAW Revision ‘NC’ of this Service Bulletin, within seven 
(7) days or before next flight, whichever occurs later:  
a) Check Mod 6/2347 FCU push rod (C6CE1398-7 and equivalent) for freedom of 
movement IAW the procedures in Section II.A. 
b) FCU push rod(s) not rejected during check IAW Section II.A must be inspected 
IAW the procedures in Section II.B. 
c) Serviceable FCU push rod(s) must be re-checked for freedom of movement IAW 
the procedures in Section II.A after re-installation. 
4. If any rod end is found unserviceable during any function check or inspection IAW this 
Service Bulletin and the applicable maintenance manual, remove both Mod 6/2347 
FCU push rods and incorporate Mod 6/2484 IAW Section II.D before further flight. 
5. Every A Check (125 hour inspection), in conjunction with PSM 1-6-7, Part 1, Basic 
Inspection – 76, Item 3.(1), repeat the check for freedom of movement IAW 
procedures in Section II.A, and lubricate IAW Section II.C and the applicable 
maintenance manual.  
6. Every 3C Check (1500 hour inspection), disconnect one end at a time and inspect  
in-situ IAW procedures in Section II.B. 
7. All unserviceable FCU push rods must be reported to Viking Technical Support 
within 10 days. Refer to the operator reply form at the end of the Service Bulletin. 
8. Incorporation of Mod 6/2484 is the terminating action to this Service Bulletin. 
E. Approval 
The technical content of this Service Bulletin has been approved under the authority of 
Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) 04-V-02. 
F. Labour Requirements 
Estimated time to accomplish this Service Bulletin is 4 hours. 
G. Weight and Balance 
Not affected. 
H. Electrical Load Data 
Not affected. 
I. Publications Affected 
PSM 1-6-7  Inspection Requirements Manual, All Series 
PSM 1-6-7(IC)  EMMA Inspection Work Cards 
PSM 1-6-2  Series 100/200 Maintenance Manual 
PSM 1-63-2  Series 300 Maintenance Manual 
PSM 1-63S-2  Series 300 Short Nose Maintenance Manual 
PSM 1-64-2  Series 400 Maintenance Manual 
PSM 1-6-4  Illustrated Parts Catalogue, Series 100/200 
PSM 1-63-4  Illustrated Parts Catalogue, Series 300 Maintenance Manual 
PSM 1-64-4  Illustrated Parts Catalogue, Series 400 Maintenance Manual

### Page 5

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 3 of 8 
J. References 
PSM 1-6-2  Series 100/200 Maintenance Manual 
PSM 1-63-2  Series 300 Maintenance Manual 
PSM 1-63S-2  Series 300 Short Nose Maintenance Manual 
PSM 1-64-2  Series 400 Maintenance Manual 
TB V6/00155 Technical Bulletin, MOD 6/ 2484 ENGINE CONTROLS - FCU PUSH ROD 
ASSEMBLY REPLACEMENT 
This Service Bulletin is self-contained. No drawings are supplied. For more information 
please contact: 
Viking Air Limited FAX: 403-295-8888 
Technical Support Telephone Numbers: 
7757 8th Street NE Regional: 587-430-0572 
Calgary, Alberta North America: 1-800-663-8444 
Canada, T2E 8A2 dh_technical.support@vikingair.com   
 
II. ACCOMPLISHMENT INSTRUCTIONS 
A. FCU PUSH RO D BINDING CHECK 
1. Grasp the FCU push rod between the nut and forward rod end (refer to Figure 1). 
2. Push the FCU push rod forward to extend the spring on the FCU Actuating Lever. 
3. Release the FCU push rod to allow the spring to return the FCU Actuating Lever to 
the idle position. 
4. If the FCU Actuating Lever does not fully return to idle position (against the idle stop) or 
returns slowly to idle position, the FCU push rod is unserviceable. Remove both Mod 6/2347 
FCU push rods and incorporate Mod 6/2484 before next flight in accordance with Section 
II.D. Repeat check for binding (steps 1. through 3.) after replacement and rigging check. 
B. INSPECTION OF MOD 6/ 2347 FCU PUSH ROD ENDS 
1. Remove FCU push rod Assemblies IAW the applicable maintenance manual:  
PSM 1-6-2  Part 5, Section 5.24.3  
PSM 1-63-2  Chapter 76, Section 76-10-05 
PSM 1-63S-2 Chapter 76, Section 76-10-05 
PSM 1-64-2  Chapter 76, Section 76-10-05 
2. Clean FCU push rod ends IAW the applicable maintenance manual:  
PSM 1-6-2  Part 5, Section 5.24.3  
PSM 1-63-2  Chapter 76, Section 76-10-05 
PSM 1-63S-2 Chapter 76, Section 76-10-05 
PSM 1-64-2  Chapter 76, Section 76-10-05 
NOTE: If the lubricant is darker than the normal colour, and/or where the lubricant is 
stickier than the normal texture, the rod ends are unserviceable. Remove both 
Mod 6/2347 FCU push rods and incorporate Mod 6/2484 in accordance with 
Section II.D before next flight.

### Page 6

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 4 of 8 
3. Inspect Mod 6/2347 FCU push rod ends IAW the applicable maintenance manual:  
PSM 1-6-2  Part 5, Section 5.24.3  
PSM 1-63-2  Chapter 76, Section 76-10-05 
PSM 1-63S-2 Chapter 76, Section 76-10-05 
PSM 1-64-2  Chapter 76, Section 76-10-05 
NOTE: Pay particular attention to the bearing ball and race for corrosion on the ball 
and chips missing from the edge of the race (refer to Figure 2).  
4. Lubricate Mod 6/2347 FCU push rod ends IAW Section II.C.  
5. Reinstall FCU push rod IAW the applicable maintenance manual: 
PSM 1-6-2  Part 5, Section 5.24.3  
PSM 1-63-2  Chapter 76, Section 76-10-05 
PSM 1-63S-2 Chapter 76, Section 76-10-05 
PSM 1-64-2  Chapter 76, Section 76-10-05 
6. Check rigging and free movement of linkage as per applicable maintenance manual:  
PSM 1-6-2  Part 5, Section 5.24.2  
PSM 1-63-2  Chapter 76, Section 76-10-01 
PSM 1-63S-2 Chapter 76, Section 76-10-01 
PSM 1-64-2  Chapter 76, Section 76-10-01 
7. Complete attached Inspection Reply Form on Page 7, and return to Viking Technical 
Support within 30 days from date of the inspection 
C. LUBRICATION OF MOD 6/2347 FCU PUSH ROD ENDS FOR CORROSION 
PREVENTION  
NOTE: Lubrication of Mod 6/2347 FCU push rod ends is required for all operating 
environments. 
CAUTION USE OF LUBRICANT OTHER THAN THOSE LISTED MAY RESULT IN 
ROD END BINDING AND/OR CORROSION. 
CAUTION EXCESSIVE SOLVENT MAY DAMAGE DRY FILM SELF-LUBRICANTING 
COATING. DO NOT USE EXCESSIVE SOLVENT TO CLEAN ROD END 
BALL. DO NOT SOAK ROD END. 
1. Solvent clean rod ends on the FCU push rod. 
2. Lightly lubricate rod ends with Royco 363 lubricating oil, or with Aeroshell Grease 22 
lubricating grease. 
NOTE: Mixing different lubricants can result in degradation of the lubricant properties 
and/or damage to the rod end. All unknown or incompatible lubricant 
previously applied must be removed before re-lubrication.

### Page 7

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 5 of 8 
D. FCU PUSH ROD REPLACEMENT 
1. Incorporate Mod 6/2484 IAW Technical Bulletin TB V6/00155 – MOD 6/2484 ENGINE 
CONTROLS - FCU PUSH ROD ASSEMBLY REPLACEMENT. 
For aircraft S/N 934 and subsequent, use Mod Kit C6MK2484-1.   
For aircraft S/N 933 and previous, use Mod Kit C6MK2484-3. 
NOTE: Mod 6/2384 is a prerequisite for Mod 6/2484. Mod 6/2384 cut-in at production 
on aircraft S/N 934. 
2. Incorporation of Mod 6/2484 is the terminating action to this Service Bulletin. 
E. RECORDING 
On completion of this Service Bulletin, make the following entry in aircraft log book: 
“Service Bulletin No. V6/0063 Revision ‘A’ has been accomplished – Engine Controls – 
Binding of the FCU Push Rod End Bearings.”   
III. MATERIAL INFORMATION AND TOOLING 
A. Material Information (Par ts Required Per Aircraft) 
In accordance with TB V6/00155: 
C6MK2484-1 Mod Kit for aircraft S/N 934 and subsequent 
C6MK2484-3 Mod Kit for aircraft S/N 933 and previous 
   Includes Mod 6/2384, which is a prerequisite for Mod 6/2484 
B. Tooling – Price and Availability 
Standard aviation hand tools  
C. Material (supplied by Operator) 
- Cleaning solvent IAW the applicable maintenance manual 
- Cloth, coarse weave 
- Cloth, lint free 
- Royco 363 Lubricating oil  
- AeroShell Grease 22, General purpose, wide temperature range

### Page 8 (OCR)

SERVICE BULLETIN V6/0063
IN. FIGURES
POWER
CONTROL
RIGGING  PIN HOLE  PULLEY  CAM FOLLOWER  LEVER  FCU  LEVER  ACTUATING  PUSH-PULL
POWER  CONTROL
PUSH ROD  0.35 IN.  (TELEFLEX)
CONTROL ROD)
FCU CONTROL ROD
•SPRING
FORWARD  SPRING
PLATE
STOP BOLT
FCU
FCU CONTROL  CAM FOLLOWER  REVERSING
ROD DISCONNECTED  PIN  LEVER
NUT
Figure 1 - FCU Rod End Bearing
mm
Figure 2 - Example of chip missing from rod end race
01-February-2021  S.B. V6/0063
Revision 'A'  Page 6 of 8

### Page 9

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 7 of 8 
Service Bulletin V6/0063 Revision ‘A’  – Operator Reply Form 
Operator:    Date of Inspection:   
Contact Person:     
Contact Phone/Email:     
A/C Registration #    A/C Serial   
A/C TTSN    A/C CSN   
LH Engine   FCU Push Rod Assembly P/N:    
RH Engine  FCU Push Rod Assembly P/N:    
LH  FCU Push Rod TTSN    TCSN   
RH  FCU Push Rod TTSN    TCSN   
Date of incorporation of Section II.A into maintenance inspection program:   
Date of incorporation of Section II.B into maintenance inspection program:   
Any occurrences of MOD 6/2347 FCU Push Rod binding to date? : YES   NO   
If ‘YES’:    Date of occurrence :  yyyy _________  mm _____ dd _____   
LH  RH   TTSN    TCSN   
Were rod ends previously lubricated?   YES   NO   
If ‘YES’ Lubrication Accomplished at TTSN _________________ TCSN    
Was corrosion found on rod end ball?  YES   NO  
If ‘YES’:   Tropical (between tropics of Cancer and Capricorn    or Temperate (outside of 
tropics of Cancer and Capricorn)   
Additional Details of Findings: 
  
  
  
 
Corrective Actions: 
  
  
  
Please return form via email to dh_technical.support@vikingair.com or via fax to 403-295-8888

### Page 10

SERVICE BULLETIN V6/0063  
01-February-2021  S.B. V6/0063 
Revision ‘A’  Page 8 of 8 
 
 
THIS PAGE INTENTIONALLY BLANK

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
