# Wipaire Service Letter 253: Revision B

- Rights: © Wipaire. Filed by the FAA in regulations.gov docket FAA-2023-1653; AD 2023-15-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Wipaire Service Letter 253](https://openairdocs.org/service-documents/wipaire/sl-253.md)
- Title as filed: Wipaire Inc Service Letter 253 Rev B
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/5c/d6/5cd6f293abf60d2d902f15fc8a630f9ee38daa6b89f0d8a49fbcf7c08cb0348f
- Page: https://openairdocs.org/service-documents/wipaire/sl-253/file/5cd6f293abf6

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

WIPLINE FLOATS • SKIS • MODIFICATIONS • AIRCRAFT SALES
AVIONICS • INTERIOR • MAINTENANCE  •  PAINT REFINISHING
1700 Henry Ave - Fleming Field (KSGS), South St. Paul, MN 55075
Phone: 651.451.1205 | Fax: 651.457.7858
www.wipaire.com
SERVICE LETTER 253
Horizontal Stabilizer Spar Cracking At Finlets
Aircraft Makes/Model(s): Float Model(s): Compliance: Mandatory By: DRH
Air Tractor
AT-802 & AT-802A
10000A Part Number: 1012347 Approved: DRR
Date: 7/27/2023 Revision: B
LOG OF REVISIONS
Revision Description Date
A Initial release 4/5/2023
B
Changes made in conjunction per request from FAA. Added finlet configuration basis for initial inspection and adjusted 
compliance windows. Adjusted recurring inspection interval. Reworded background and compliance method. Added 
Figure 1 and renumbered following figures. Made LH inspection mandatory regardless of findings on RH (step 9). Added 
reporting step to Aircraft Closing and Return to Service section.
7/27/2023
EFFECTIVITY:
This service letter applies to Air Tractor models AT-802 and AT-802A with Wipline 10000 Amphibian Floats installed per STC 
SA01795CH, as well as previously floated aircraft that have been converted to landplane configuration under the same STC.
COMPLIANCE:
Compliance is mandatory with initial inspection window based on finlet configuration. Refer to Figure 1 / Wipaire drawing 
7D1-4399.
1. For STC configuration 7D1-4399-01: Within 3 days or 24 hours time-in-service (TIS) or before the accumulation of 200 
hours TIS since the installation of the STC, whichever occurs later.
2. For STC configuration 7D1-4399-02: Within 5 days or 24 hours TIS or before the accumulation of 300 hours TIS since the 
installation of the STC, whichever occurs later.
3. For STC configuration 7D1-4399-03: Within 15 days or 24 hours TIS, whichever happens later, or before the accumulation 
of 600 hours TIS since the installation of the STC, whichever occurs later.
4. Previously floated aircraft in landplane configuration per Wipaire drawings 1003406 (AT-802) or 7D1-4405 (AT-802A); 
inspect according to limits associated with configuration 7D1-4399-01, as provided above.
Prior compliance with revision A of this letter satisfies the initial inspection requirements for the right hand stabilizer (inspection 
of the left hand stabilizer is required if not previously accomplished). Replacement of the spar due to cracking associated with 
this letter also satisfies the initial inspection requirement for that side of the stabilizer.
In all cases, re-accomplish this inspection at 200 hours TIS intervals from the initial action.
BACKGROUND:
Instances of cracked horizontal stabilizer spars have been observed, primarily on the forward spars near both the lower and 
upper finlet mounting locations, at/near the spar bend radii.

### Page 2

Revision B Page 2 of 6  P/N 1012347
 SERVICE LETTER 253
 Horizontal Stabilizer Spar Cracking At Finlets
Work Instructions
1. Position and prepare aircraft for safe maintenance.
Refer to Figure 2 and Wipaire drawing 7D1-4399 for steps 2 and 3.
2. Remove upper and lower finlets from the right horizontal stabilizer.
COMPLIANCE METHOD:
Inspect the finlet mount areas as outlined in work instructions. Photos of characteristic cracks are included in this Service 
Letter. Any cracks discovered in this area of the horizontal stabilizer spar necessitate replacement or repair of spar. Contact 
local Air Tractor dealer for replacement parts and any relevant/available service documents.
APPROXIMATE SHOP HOURS: 
Performing the work instructions will take approximately 10 labor hours to complete per aircraft, excluding replacement/repair 
of the spar itself.
WARRANTY INFORMATION: 
Parts and labor warranty is not included.
TECHNICAL DATA:
Copies of this service letter, associated service kit (if applicable), float service manual, and float parts manual are available at 
www.wipaire.com or by contacting Wipaire customer service at customerservice@wipaire.com. 
Figure 1
Finlet configurations (RH stabilizer shown)

### Page 3

Revision B Page 3 of 6  P/N 1012347
 SERVICE LETTER 253
 Horizontal Stabilizer Spar Cracking At Finlets
Figure 3
Stabilizer forward spar strap locations (LH stabilizer shown)
4. Remove the upper and lower spar strap (10A12001-074) from the forward horizontal stabilizer spar by drilling out the 
rivets holding it in place. See the parts highlighted in red in Figure 3.
Note: Rivet quantity and type may vary.
Figure 2
Inspection access locations
3. Remove the inspection access cover from the bottom of the right horizontal stabilizer.
Note: Finlet sizes/configurations and the presence of the finlet stabilizing struts will vary with the model and horsepower of the 
aircraft.

### Page 4

Revision B Page 4 of 6  P/N 1012347
 SERVICE LETTER 253
 Horizontal Stabilizer Spar Cracking At Finlets
5. Clean the area that is to be inspected.
6. Visually inspect for cracks on the forward horizontal stabilizer spar, including both upper and lower flanges and the web 
area between. Two primary varieties of cracks have been observed. These are described below to aid inspection, but the 
entire area is to be thoroughly examined:
a. A crack originating in the spar web above the forward, outboard mount bolt of the lower finlet. See Figures 4 and 5.
b. A crack near the forward, inboard mount bolt, typically within the radius of the spar, and perhaps centered at the 
corner of the strut brace shim plates. See Figure 6.
Note: Non-destructive testing such as dye penetrant or eddy current may be required to confirm or rule-out the presence of 
cracks, at inspector’s discretion.
Figure 4
Crack above lower finlet forward, outboard mount bolt location (spar strap removed)
Figure 5
Early-stage crack above lower finlet forward, outboard mount bolt location (shown with spar strap in place)
Early-Stage 
Crack

### Page 5

Revision B Page 5 of 6  P/N 1012347
 SERVICE LETTER 253
 Horizontal Stabilizer Spar Cracking At Finlets
Figure 6
Crack at lower finlet forward, inboard mount bolt location (spar strap removed)
7. If no cracks are present continue to the next step, otherwise:
Any cracks discovered in this area of the horizontal stabilizer spar necessitate replacement or repair of spar; the procedure for 
replacing or repairing the spar is beyond the scope of Service Letter 253.
If finlet spar strap(s) require replacement, refer to Wipaire drawing 7D1-4399 for fitment of the new strap. 
Contact Wipaire Customer Service to request the most current revision at: customerservice@wipaire.com and/or 
technicalsupport@firebossllc.com.
8. Install the following (Ref Wipaire drawing 7D1-4399):
a. Spar straps
b. Lower horizontal stabilizer access cover
c. Upper and lower finlets:
i. Apply Loctite 242 or equivalent thread locker (medium strength) to the bolt when installing
ii. Torque the attach bolts 50 in-lbs. to 70 in-lbs
iii. Apply torque stripe to the bolt head
9. REPEAT THIS INSPECTION FOR LEFT HORIZONTAL STABILIZER .

### Page 6

Revision B Page 6 of 6  P/N 1012347
 SERVICE LETTER 253
 Horizontal Stabilizer Spar Cracking At Finlets
Aircraft Closing & Return to Service
1. Upon completion of inspection, enter information in Aircraft Logbook for completion of Wipaire Service Letter 253 rev. B, 
and note observations.
2. Report ALL inspections to Wipaire regardless of whether or not cracks were revealed. Include the following information:
• Hours since initial modifications associated with STC SA01735CH occurred
• Model/engine configuration (with HP limits)
• Propeller type
• Finlet configuration (7D1-4399-1, 7D1-4399-2, 7D1-4399-3, landplane)
• Crack location(s), if applicable (RH/LH, upper/lower spar flange, inboard/outboard finlet mount hole, etc.)
• Crack size(s), if applicable
• Photos of crack(s), if found
• Registration number
• Serial number
• Total hours on airframe
• Operator comments

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
