# Zodiac Aerospace Service Bulletin MC10-35-274: MC10-35-274

- Rights: © Zodiac Aerospace. Filed by the FAA in regulations.gov docket FAA-2017-0505; AD 2018-21-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Zodiac Aerospace Service Bulletin MC10-35-274](https://openairdocs.org/service-documents/zodiac/mc10-35-274.md)
- Title as filed: MC10-35-274
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/9e/2f/9e2f5e6c53fe8d07a85f8cce61e29ce4c6bc6c54bd49bf9169ce2920cf33ecf9
- Page: https://openairdocs.org/service-documents/zodiac/mc10-35-274/file/9e2f5e6c53fe

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ZODIAC AEROSPACE SERVICES  
  
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
 PAGE: 1/2
 
ZODIAC AEROSPACE SERVICES 
Technical Publication Department 
ZODIAC SERVICES EUROPE 
61, rue Pierre CURIE 
CS20001 
78373 PLAISIR CEDEX / FRANCE 
Phone : +33 1 61 34 23 23 
Fax : +33 1 30 55 71 61 
 
TPI Web site: http://www.in-services.fr/technical/tpi 
TRANSMITTAL SHEET 
 
 
This Transmittal Sheet applies to the Revision 02, dated 20140625, of Service Bulletin MC10-35-274 
 
REASON FOR REVISION 
 
Airworthiness Directive reference added. 
Correction of Zodiac Aerospace UK location. 
Correction of Amdt letter 
 
 
 
REVISION SEQUENCE 
 
Initial issue : 20140319 
Rev01: 20140418 
Rev02: 20140625

### Page 2

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
 PAGE: 2/2
 
 
THIS PAGE INTENTIONALLY LEFT BLANK

### Page 3

ZODIAC AEROTECHNICS  
AIRCRAFT SYSTEMS | CABIN & COCKPIT SYSTEMS DIVISION  
OXYGEN SYSTEMS EUROPE (OSE). 
61, RUE PIERRE CURIE – CS20001 
78373 PLAISIR CEDEX - FRANCE 
Phone : (33) 01 61 24 23 23 - Fax : (33) 01 30 55 71 61 
SERVICE BULLETIN
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 1/9
 
 
 
TITLE:  OXYGEN – HARNESS ASSEMBLY - INSPECTION FOR POTENTIAL 
DEFECTIVE COMPONENT 
 
1. PLANNING INFORMATION 
A. Effectivity 
(1) Potential Concerned equipment 
This Service Bulletin applies to the following Crew Oxygen Mask Regulator fitted with a 
inflatable harness assembly Part Number (PNR) MXH20-1 or MXH21-1. 
PNR HARNESS 
MC10‐02‐50  MXH21-1 
MC10‐02‐155  MXH21-1 
MC10‐04‐159  MXH21-1 
MC10‐13‐150  MXH20-1 
MC10‐15‐151  MXH20-1 
MC10‐15‐152  MXH20-1 
PNR HARNESS 
MC10‐15‐157  MXH20-1 
MC10‐15‐158  MXH20-1 
MC10‐15‐166  MXH20-1 
MC10‐15‐171  MXH20-1 
MC10‐15‐176  MXH20-1 
MC10‐16‐150  MXH20-1 
PNR HARNESS 
MC10‐16‐151  MXH20-1 
MC10‐19‐151  MXH21-1 
MC10‐25‐154  MXH21-1 
MC10‐25‐158  MXH21-1 
 
(2) Affected sub-assembly 
This Service Bulletin applies to the harness hose equipped PNR 445186 or 445952 
fitted on the  inflatable harness asse mbly PNR MXH20-1 or MXH21-1 and 
manufactured between 50 th week of 2008  year (0850S) and 51 th week of 2010  year 
(1051S). 
(3) In the field 
Crew Oxygen Mask Regulator listed above and equipped with potentially defective 
harness hose. 
(4) Spare parts 
Defective harness hose equipped PNR 445186 or 445952 or inflatable harness PNR 
MXH20-1 or MXH21-1 from stock. 
B. Concurrent Requirements 
Affected customers should notify thei r usual Zodiac Services contacts in regards of their location  
(ZS Europe, ZS UK, ZS Middle East,  ZS Asia and ZS Americas). 
Customers to provide the list of PNR affected and place the corresponding orders for replacement. 
Removed harnesse hoses must be sent in one batch at the end of the retrofit to the ZS work shop 
from which your area corresponds to.

### Page 4

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 2/9
 
C. Reason 
This Service Bulletin is issued : 
- To inform the operators of the potential risk of premature rupture on the inflatable harness. 
- To provide instructions for inspection and pr eventive replacement if necessary of potentially 
defective inflatable harness.  
D. Description 
Based on our internal review and customer  feedback, ZODIAC AEROTECHNICS formally 
INTERTECHNIQUE has identified the potentially defective batches of silicon tubes. 
Inflatable harnesses assembled with defective s ilicon tubes have demonstrated an unusually high 
premature rupture rate. 
E. Compliance 
Incorporation of this Service Bulletin is ma ndatory. (refer to Airworthiness Directive  
AD No: 2014-0142). 
F. Approval 
This document was established in conformity  with the ZODIAC AEROTECHNICS "Alternative 
Procedures to Design Or ganisation Approval" ref. PGQ-5030 a pproved by the EASA. Technical 
data were approved by ZODIAC AEROTECHNICS in conformity with § 21A.611 of PART 21. 
G. Manpower 
(1) 1 technician 
(2) Check only : 5 minutes. 
(3) Complete Operation : 20 minutes. 
H. Weight and Balance 
None 
I. Electrical Load Data 
Not Changed 
J. Software Accomplishment Summary 
Not applicable 
K. References 
(1) Component Maintenance Manuals 
See APPENDIX I 
L. Publications Affected 
(1) Component Maintenance Manuals 
See APPENDIX I 
M. Interchangeability 
Not affected

### Page 5

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 3/9
 
2. MATERIAL INFORMATION 
A. Material – Price and Availability 
(1) Material 
PNR KEYWORD QTY 
MXH21-1 INFLATABLE HARNESS 1 
Or 445952  HARNESS HOSE EQUIPPED 1 
MXH21-31 (1)  INFLATABLE HARNESS 1 
Or 420B156 (1)  HARNESS HOSE EQUIPPED 1 
081356 (1) & (2) NAMEPLATE (MXH21-31) 1 
417448 (2) CLAMP 1 
(1) Post SB MA_B_C_F10-35-260 
(2) Necessary when changing harness hose only. 
Inflatable harness MXH21-1 (including harness hose  equipped PNR 445952) are modified to MXH21-31 
(including Harness hose equipped PNR 420B156) due to service bulletin MA_B_C_F10-35-260. 
(2)  Price 
On request 
(3) Availability 
Schedule to be agreed with customers. 
B. Industry Support Information 
Not applicable 
C. Material Necessary fo r Each Component (Unit) 
(1) Material to order 
PNR KEYWORD QTY ORDER SPECIAL INSTRUCTIONS 
MXH20-1 INFLATABLE HARNESS 1 MXH21-31 (1)  Forward to Zodiac Services maintenance facility* 
Or 445186 HARNESS HOSE EQUIPPED 1 Or 420B156 (1) Forward to Zodiac Services maintenance facility* 
MXH21-1 INFLATABLE HARNESS 1 MXH21-1 Forward to Zodiac Services maintenance facility* 
Or 445952 HARNESS HOSE EQUIPPED 1 445952 Forward to Zodiac Services maintenance facility* 
MXH21-1 INFLATABLE HARNESS 1 MXH21-31 (1)  Forward to Zodiac Services maintenance facility* 
Or 445952 HARNESS HOSE EQUIPPED 1 Or 420B156 (1) Forward to Zodiac Services maintenance facility*

### Page 6

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 4/9
 
PNR KEYWORD QTY ORDER SPECIAL INSTRUCTIONS 
417448 (2) CLAMP 1 417448 TO DISCARD 
(1)  Post SB MA_B_C_F10-35-260 
(2) Necessary when changing harness hose only. 
* Refer to § 3.D. 
 
D. Material necessary for each spare 
Not applicable 
E. Re-identified Parts 
With indelible ink or an electric pen, write visibly the SB accomplishment by adding of letter “ I“ 
(Inspected) on the bushing of inflatable harness (See Figure 2). 
The marking shall be visible once the harness has been re-installed on the mask. 
F. Tooling – Price and Availability 
Not applicable 
3. ACCOMPLISHMENT INSTRUCTIONS 
A. From the stock : 
(1) Inspect the manufacturing date  (See Figure 3) of the inflatable harness or harness hose 
equipped : 
- If the manufacturing date is in the specified period above, forward the defective inflatable 
harness or harness hose equipped to the appropriate Zodiac Services maintenance facility for 
replacement of the inflatable harness. 
B. Inflatable harness mounted on t he Crew Oxygen Mask Regulator : 
WARNING : STRICTLY OBEY THE PROCEDURES WHEN  YOU DO WORK ON OXYGEN SYSTEM. 
DO NOT USE OIL, GREASE OR OTHER LUBR ICANTS MADE FROM PETROL IN THE 
AREA OF OXYGEN EQUIPMENT. YOU CAN CAUSE A FIRE OR EXPLOSION. 
CAUTION :  APPLY THIS SB ON CLEAN SURFACE AND WITH CLEAN HANDS. 
Prior to using the flow chart to start the on-aircraft action(s), the operator, if he has the possibility, can 
determine, (e.g. aircraft maintenance logs check) whether the inflatable harness has been replaced, 
during a maintenance operation, on an oxygen mask regulator installed on the aircraft.

### Page 7

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 5/9
 
 
 
  
Stow the  Crew Oxygen Mask  
into its housing
Remove the inflatable harness from the Crew 
Oxygen Mask  (Refer to § 3.B.(1))
Inspect the harness hose
manufacturing date
Replace the harness hose
equipped § (3.B.(2) and § (3.B.(3) 
or 
replace the inflatable harness
assembly
Add the letter ” I” on the 
bushing of inflatable harness
Re-Install the inflatable harness to 
the Crew Oxygen Mask § (3.B.(4))
Make the test of the  Crew Oxygen
Mask (Refer to § 3.B.(5))
Disconnect the Crew Oxygen Mask from the  A/C 
oxygen supply source
Connect the Crew Oxygen Mask to the  
A/C oxygen supply source, 
if desconnected.
No
Yes
Forward the defective equipment  
to the appropriate Zodiac 
Services maintenance facility for 
replacement. 
(Refer to § 3.D)
Letter " I " marked on 
the bushing of 
inflatable harness of 
the Crew Oxygen
Mask
Manufacturing
date is between
0850S and 1051S
Inspect the letter  ”I” on the bushing of 
inflatable harness (Refer to Figure 2)
Yes
If applicable: Add the Amdt letter
to the identification plate of the 
Crew Oxygen Mask
(Refer to § 3.C)
Yes
or
unknown
unstow the Crew Oxygen 
Mask from its housing
Start End
If visible  : Inspect the 
harness hose equipped
manufacturing date
Manufacturing
date is between
0850S and 1051S
No
Action to be performed on Aircraft 
Action to be performed in the certified 
PART 145 workshop or maintenance 
organization approved by civil aviation 
authority

### Page 8

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 6/9
 
(1) Removal of the inflatable harness from the Crew Oxygen Mask Regulator: 
(a) Remove the screw from the inflatable harness with magnetic-screwdriver slotted (3x_ _). 
(b) Lift the locking tab of the coupling block whic h is in front of the regulator by 1 to 2 mm 
(0.04 to 0.08 in). 
(c) Hold the locking tab up and move the coupling block apart from the regulator. 
(2) Disassembly of the comfort inflat able harness PNR MXH20-1 or MXH21-1. 
(a) Disengage the clamp with a screwdriver. Lift up the clamp  at different  locations. 
Discard the clamp. 
NOTE : Take care not to damage the block. 
(b) Remove the harness hose equipped from the harness block. 
(c) If applicable, Remove the nameplate (MXH20-1  or MXH21-1) from the harness block. 
Note: Clean the harness block with isopropyl alcohol and lint free cloth. 
(3) Assembly of the comfort inflat able Harness MXH21-1 or MXH21-31 
(a) Install the O-rings on the ends of the harness hoses. 
NOTE : The O-rings are lubricated with compatible oxygen lubricant. 
(b) Install the ends of the harn ess hoses in the coupling block. 
1 Check the direction of the harness hoses (head strap to the top), 
2 Position each end of the hoses in its housing in harness block (30). Make sure that 
the harness hoses are not twisted, 
3 Hold the ends of the harness hoses (50) in place manually. 
(c) Pinch the clamp (20) to engage it in the ends of the harness hoses. Press the clamp 
until it comes fully to its position (you will hear a click). 
NOTE : Make sure that the clamp is correctly locked on each end of the harness 
hoses; its upper face must be flush with the coupling block. 
(d) Check that each tube end is correctly locked. 
(e) If applicable, Install the nameplate (MXH21-31) to the harness block. 
(4) Installation of the inflatable harness  to the Crew Oxygen Mask Regulator: 
(a) Install the harness on the regulator body and attach it with the screw. 
(b) Torque the harness attachment screw 0,20 N.m ± 0,02 (1.77 lb.in ± 0.17). 
(5) Test of the Oxygen Crew Mask 
(a) Make the test of the time and the comfort function: 
(refer to CMM 35-13-63 Subtask 35-13-63-790-005-A01)

### Page 9

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 7/9
 
C. Re-identification 
After modification (1) of inflatable harness PNR MXH20-1 or  MXH21-1 by inflatable harness PNR 
MXH21-31 or harness hose assembly PNR 445186  or 445952 by harness hose assembly PNR 
420B156, The Crew Oxygen Mask Regulators MC10 Se ries are identified with the amendment  
letter : W 
(1) With indelible ink, write the relevant  amendment letter on the identification label 
(1)  Post SB MA_B_C_F10-35-260  
D. Declaration of Modification 
The form attached in appendix II is to be filled by the customer and attach to the PO. 
 
 
 
 
 
 
 
Figure 1 – “ I “ Letter Position 
I

### Page 10

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 8/9
 
 
Figure 2 – Manufacturing Date Explanation 
E. ZODIAC SERVICES Facilities 
EUROPE MIDDLE EAST 
ZODIAC SERVICES EUROPE 
61, rue Pierre CURIE 
CS20001 
78373 PLAISIR CEDEX / FRANCE 
Phone : +33 1 61 34 23 23 
Fax : +33 1 30 55 71 61 
ZODIAC AEROSPACE UK 
Unit 610 Avenue West 
Skyline 120 
BRAINTREE - CM77 7AA, ENGLAND 
Phone: 44 (0)-1376-329-194 
Fax: 44 (0)-1376-340-734 
IN-SERVICES MIDDLE EAST 
Abu Dhabi International Airport 
Cargo Village Area  
P.O. Box No 106675 
ABU DHABI - UNITED ARAB 
EMIRATES 
Phone : + 971 2575 7088 
Fax : + 971 2575 8482 
USA ASIA  
ZODIAC SERVICES AMERICAS 
4900 St. Joe Boulevard, 
Building 200, Suite 400 
COLLEGE PARK, GA 30337 
USA 
Phone : +1 678 228 8153 
Fax : +1 800 879 0411 
ZODIAC SERVICES ASIA 
36, Loyang Drive 
SINGAPORE 508949 
Phone : +65 6579 2230 
Fax : +65 6579 2231 
 
 
APPENDIX I 
CMM N° EQUIPMENT PNR DESIGNATION 
35-13-63 MC10 Series CREW OXYGEN MASK REGULATOR  
Manufacturing Date 
Year Week 
eg.: 0837 = 37h week of 2008

### Page 11

SERVICE BULLETIN 
 
DATE: 20140625 SERVICE BULLETIN: MC10-35-274
REVISION N°: 2 PAGE: 9/9
 
APPENDIX II 
 
DECLARATION OF MODIFICATION 
EQUIPMENT(S) MODIFIED: 
Mask Harness 
PNR SNR PNR Batch number 
 
 
   
NAME AND ADDRESS OF AIRLINES or FAR/JAR 145 REPAIR STATION: 
Modification Date: 
Name, position, signature of the modification responsible:

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
