# TCDS 1E3: General Electric Company

- Type: Type certificate data sheet
- Status: Current
- Holder: General Electric Company
- Revision: 16
- Revised: September 4, 2018
- Product: Engine
- Certification basis: CAR 13
- Registered aircraft: 53, by the registry models matched to it (OpenAirDocs)
- Data sheet PDF: https://openairdocs.org/files/sha256/30/a9/30a9756717c49830886b5c396c89ded243b63178240148b47bfc328ca974b827
- FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/6C49E2F78231C5288625830500667BB1.0001
- Page: https://openairdocs.org/tcds/1E3

## Models (5)

As the data sheet lists them.

- CT58-100-2
- CT58-140-2
- CT58-140-1
- CT58-110-1
- CT58-110-2

## What the data sheet says

From the PDF's text layer, line by line; tables lose their columns. The PDF is the record.

```text
Page No. 1 2 3 4 5 
Rev. No. 15 15 16 15 16 
Reformatted 10/94 
DEPARTMENT OF TRANSPORTATION 
FEDERAL AVIATION ADMINISTRATION 
 
1E3 
Revision 16 
General Electric  
CT58-100-2 
CT58-110-1 
CT58-110-2 
CT58-140-1 
CT58-140-2 
 
Sept 4, 2018 
 
TYPE CERTIFICATE DATA SHEET NO. 1E3 
 
Engines of models described herein conforming with this data sheet (which is a part of type certificate No. 1E3) and other 
approved data on file with the Federal Aviation Administration, meet the minimum standards for use in certificated aircraft i n 
accordance with pertinent aircraft data sheets and applic able portions of the Civil Air Regulations/Federal Aviation Regulations 
provided they are installed, operated, and maintained as prescribed by the approved manufacturer's manuals and other approved 
instructions. 
 
Type Certificate Holder General Electric Company 
 Aircraft Engine Group 
 Lynn, Massachusetts  01910 
 
Model  
CT58-100-2 
 
CT58-110-1 
 
CT58-110-2 
CT58-140-1 
CT58-140-2 
Type    Axial flow, free turbine turboshaft  
Ten stage compressor  
Annular combustion chamber  
Two stage gas generator turbine  
Single stage power turbine 
    
Ratings (See NOTE 14)     
At nominal power turbine speed of 19,500 r.p.m.     
Max. continuous at sea level; hp.   990 1050 - - 1250 
Takeoff (5 min.) at sea level; hp. 1050 1250 - - 1400 
30 min. helicopter rating at sea level; hp.  1250 - - 1400 
2½ min. helicopter rating at sea level; hp.   1350 - - 1500 
Alternate rating (See NOTE 9)     
Max. continuous & takeoff at sea level; hp.   730 - - - - - - 
Fuel control Hamilton Standard JFC-26 
& Pesco 023104 gear type 
fuel pump with integral 
boost. 
 
- - - - - - 
Fuel (See NOTE 15) Fuel conforming to General 
Electric Company Jet Fuel 
Specification No. D50TF2, 
current revision.  Kerosene, 
JF4 and JP5 fuels are 
acceptable but whenever a 
change is made, re-
adjustment of the fuel 
control to the appropriate 
setting must be made. 
 
- - - - - -

1E3 2 
 
Model          (cont'd)  
CT58-100-2 
 
CT58-110-1 
 
CT58-110-2 
CT58-140-1 
CT58-140-2 
Oil Oil conforming to General 
Electric Specification No. 
D50TF1, current revision.  
See applicable Operations 
Bulletin for specific oils 
approved per the subject 
specification. 
- - - - - - 
Principal dimensions     
Length, in. 59 - - - - - - 
Max. diameter, in. 16 - - - - - - 
Weight (dry), lb. (includes essential engine 
accessories and turbine bucket guard) 
295 315 335 340 
C.G. Location with down exhaust     
Aft of front mount centerline, in. 18.45 - - 18.88 19.65 
Below engine centerline, in. 1.50 - - - - 1.80 
Ignition system 
(24 volts D.C. 150 watts max.) 
Bendix Scintilla dual 
ignition unit type TGLN 
with integral junction box 
assembly and two igniter 
plugs 
- - - - - - 
Igniter plugs P/N 37B200275 - - - - - - 
NOTES 1 through 13, 15, 17, & 18 1 thru 18 - - 1 thru 15, 
17, & 18 
"- -" indicates "same as preceding model" 
"" indicates "does not apply" 
 
Certification basis: 
 
Regulations & Amendments 
 
Model 
 
Date of Application 
Date Type Certificate  
No. 1E3 Issued/Revised 
 
Date of Cancellation 
CAR 13, effective June 15,  CT58-100-1 June 2, 1958 July 1, 1959 September 15, 1982 
1956 as amended by 13-1,  CT58-100-2 September 15, 1959 December 29, 1960  
13-2, 13-3, 13-4, 13-5, & 13-6 CT58-110-1 September 24, 1959 July 13, 1961  
 CT58-140-1 June 23, 1964 June 10, 1965  
 CT58-110-2 October 31, 1967 March 29, 1968  
 CT58-140-2 January 25, 1968 April 18, 1968  
 
Production basis: Production Certificate No. 107. 
 
 
NOTE 1. Maximum permissible gas generator operating speeds (r.p.m.) are as follows: 
 CT58-100-2 CT58-110-1 CT58-110-2 CT58-140-1 CT58-140-2 
2½ minute helicopter rating  26,800 - - - - 27,200 
30 minute helicopter rating  26,300 - - - - - - 
Takeoff 25,600 26,300 - - - - - - 
Maximum continuous 25,600 24,300 - - - - - - 
Alternate rating 24,300 - - - - - - - -

3
 1E3 
NOTE 2. Maximum permissible temperatures: 
 
 CT58-100-2 CT58-110-1 CT58-110-2 CT58-140-1 CT58-140-2 
Power Turbine Inlet (T5)*      
2½ minute helicopter rating  1300°F - - 1330°F 1397° 
30 minute helicopter rating  1250°F - - 1285°F - - 
Takeoff 1175°F 1250°F - - 1285°F - - 
Maximum continuous 1115°F 1175°F - - 1220°F - - 
Maximum transient 1545°F (2 sec.) - - - - 1545°F (2 sec.) 
1465°F (20 sec.) 
- - 
Starting 1545°F (4 sec.) - - - - 1740°F (2 sec.) - - 
Oil inlet 250°F - - - - - - - - 
  
 *The power turbine inlet gas temperature is measured by eight (8) thermocouples mounted in a radial plane in the 
second stage turbine casing.  Refer to General Electric Maintenance Manual SEI 101  
 CT58-100-2/-110-1/-110-2) and SEI-182 (CT58-140-1/140-2) for inspection requirements when limits are 
exceeded. 
 
NOTE 3. Fuel and oil pressure limits: 
 
 Fuel: Minimum at engine pump inlet, 0.3 V/L (max.) with maximum 50 p.s.i. above ambient  atmospheric 
pressure. 
 
 Oil: At ground idle, 8 p.s.i.g. minimum 
  Operating range, 20 to 60 p.s.i.g. 
 
NOTE 4. Accessory drive provisions: 
  Rotation    
  Facing  Max. Torque (in. lb.) 
Drive Type Engine Pad Speed Continuous Static 
Starter Special CC 1.0* 180 336 
Gas generator tachometer AND 20005 Type XVB C 0.160* 7 50 
Power turbine tachometer AND 20005 Type XVB CC 0.200** 7 50 
Fuel filter Special CC 0.160* 5 50 
  "C"-  Clockwise,     "CC" - Counter-clockwise 
  * Speed - Times gas generator r.p.m. 
  ** Speed - Times power turbine r.p.m. 
 
NOTE 5. Engine ratings are based on calibrated test stand performance under the following conditions: 
 
  Static sea level standard conditions of 59°F and 29.92 in. Hg. 
  General Electric air inlet #1076669-886 and bullet nose #1076669-424. 
  No external air bleed or accessory drive power for aircraft accessories. 
  Exhaust configuration as defined by G.E. drawing #37E500110 (100-2, 110-1, 110-2) & #4006T87  
  (140-1, 140-2). 
  No anti-icing airflow. 
  Additional performance parameters are contained in General Electric Operating Instructions SEI-103 (100-2), SEI-
180 (110-1, 110-2) and SEI-197 (140-1, 140-2). 
 
NOTE 6. Maximum permissible air bleed extraction is 5.6 percent at standard conditions for 100- 2, 110-1, and 110-2; and 
3.0 percent for 140-1 and 140-2.

1E3 4 
NOTE 7. Power Turbine Normal Operating Range.  The nominal power turbine operating speed is 19,500 r.p.m.  An 
alternate nominal speed of 20,250 r.p.m. can also be provided.  For engine identification and fuel control 
requirements refer to G.E. Service Bulletin 124.  The engine control system provides for power turbine speed 
governing within the following limits: 
 
     Model  Min. Governing Speed Governor Topping Speed 
     100-2  16,600 r.p.m. 21,275 r.p.m. 
     110-1, 110-2 16,600 r.p.m. 21,275 r.p.m. 
     140-1, 140-2 17,000 r.p.m. 21,275 r.p.m. 
 
NOTE 8. Power Turbine Shaft Torque Limits - All Models: 
 
  Static   11,100 in. lb. 
  Maximum continuous No limit, provided that all other power, speed and temperature limits are maintained.  
 
NOTE 9. All models can be provided with alternate power ratings as noted.  A fuel control change is required to make this 
rating change.  Refer to CT58 Service Bulletin #45 for listing of approved fuel controls.  In addition the following 
CT58-140 ratings are provided: 
 
 CT58-140-1 CT58-140-2 
 Horsepower Horsepower 
Rating 59°F 80°F 59°F 80°F 
2½ Minute 1500 1350 1500 1500 
30 Minute & Takeoff 1250 1250 1250 1250 
Maximum Continuous 1050 1050 1050 1050 
 
NOTE 10. To be eligible for use in certificated aircraft, the engine installation must include an accurate engine output torque 
measuring device or an acceptable alternate means of determining engine power. 
 
NOTE 11. This engine meets FAA requirements for operation in icing conditions, for adequate turbine disc integrity and rotor 
blade containment and does not require airframe-mounted armoring. 
 
NOTE 12. Maximum permissible overspeeds are: 
 Gas generator 27,600 r.p.m. for 15 seconds (CT58-100-2/-110-1/-110-2) 28,300 rpm for 20 seconds (CT58-140-
1/140-2) 
 Power Turbine 23,100 r.p.m. for 15 seconds. 
 When either of these limits is exceeded, the engine must be disassembled for inspection.  
 
NOTE 13. Because of differences in engine application and installation, each engine installation design must be evaluated 
with regard to engine overspeed protection and an airframe-mounted speed switch provided if deemed necessary. 
 
NOTE 14. Below 59°F the sea level static power limits for the CT58-110-1/-2 and CT58-140-1/-2 engines will vary as 
follows: 
 
Rating CT58-110-1/110-2 CT58-140-1 CT58-140-2 
2½ Min. Helicopter No variation - engine is flat rated Increases linearly from 1500 hp. Increases linearly from 1500 hp. 
 at 1350 hp. at 59°F and below. at 59°F to 1545 hp. at -65°F at 59°F to 1560 hp. at -65°F. 
    
Takeoff & 30 Min. Increases from 1250 hp. at 59°F Increases linearly from 1400 hp. Increases linearly from 1400 hp. 
Helicopter to 1350 hp. at +23°F and flat at 59°F to 1510 hp. at 22°F and at 59° to 1530 hp. at 13°F and 
 rated below this temperatures.  to 1540 hp. at -65°F. to 1560 hp. at -65°F. 
    
Max. Continuous Increases linearly from 1050 hp. Increases linearly from 1250 hp. - - 
 at 59°F to 1230 hp. at 29°F and at 59 F to 1390 hp. at 39°F   
 flat rated at 1230 hp. at 29°F  and flat rated at 1390 hp. at   
 and below 39°F and below.

5
 1E3 
 For power rating variation between standard day conditions and the temperatures listed above, refer to General 
Electric Operating Instructions No. 180 (CT58-110-1, 110-2) and No. 197 (CT58-140-1, 140-2).  The ratings 
referred to herein and the limitations on the usage of these ratings are defined in the applicable FARs.  
 
 Engines with individual performance characteristics and capabilities to develop the low temperature power ratings 
noted above at higher ambient temperatures may be operated up to these power limits at any ambient conditions 
provided all other engine parameters are not exceeded. 
 
NOTE 15. The only optional additives which may be used in approved fuels are as follows: 
 (1) Phillips PFA-55MB or anti-icing additives to specification MIL-I-27686E at a concentration not in excess of 
0.15% by volume. 
 
 (2) SOHIO Biobor JF biocide additive at a concentration not in excess of 20 p.p.m. elemental boron (270 ppm 
total additive). 
 
 (3) Shell ASA-3 anti-static additive at a concentration that will provide not in excess of 300 conductivity units 
which is approximately equivalent to 1 p.p.m. 
 
 The above additives may be used in combination. 
 
 With the fuel boost pump (Part Number 5183T66P01) installed, fuel system icing inhibitor ( FSII) must be added to 
the fuel when flight conditions are known or forecast to be at or below 32 degrees F (0 degrees C). 
 
NOTE 16. A speed decreaser gear defined by General Electric drawing 37R600175 is eligible for use on  
 CT58-110-1, -110-2 engines.  This provides a gear reduction ratio of 3.25 to 1 and includes an integral torque 
sensing device.  Oil conforming to General Electric Specification No. 050TF1 must be supplied to the gear box 
from the airframe oil supply system.  Normal oil pressure operating limits for the gear box are 35 to 75 p.s.i.  
 
NOTE 17. The CT58-100-2 and CT58-110-1 engines incorporate improved hot section parts to permit operation at higher 
turbine inlet temperatures and increased ratings.  The CT58- 100-2 does not utilize the higher rating. 
 
 "Military T58-GE-1 engines with serial numbers below 277135 were manufactured identical to the  
 CT58-110-1, and military T58-GE-5 engines with serial numbers below 285373 and below 291053 were 
manufactured identical to the CT58-140-1.  These engines are eligible for use in certificated aircraft if they 
conform to the FAA approved parts lists, are in an acceptable airworthiness condition, and the engine nameplate 
has been revised or replaced to include the corresponding civil model designation and Type Certificate number.  
Consult General Electric for specified requirements.  The T58-GE-1 and  
 T58-GE-5 models were removed from active certification status on 16 September 1971." 
 
 The CT58-140-1 engine is similar to the CT58-110-1 except for improved parts, increased airflow and compressor 
efficiency. 
 
 The CT58-110-2 engine is similar to the CT58-110-1 with selected CT58-140-1 hardware incorporated for life and 
performance improvements. 
 
 The CT58-140-2 engine is identical to the CT58-140-1 except for improved performance at above standard day 
temperature conditions and an increased flow fuel control.  Refer to NOTES 9 and 14. 
 
NOTE 18. "Life limits established for critical rotating components are published in the CT58 Overhaul Manuals  
 SEI-102 (CT58-100-2/-110-1/-110-2) and SEI-183 (CT58-140-1, -2)." 
 
 
 
....END...
```

## ADs (20, in force first)

- [AD 2015-20-09](https://openairdocs.org/ad/2015-20-09): Life-limited rotating parts · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Nov 18, 2015
- [AD 2005-04-10](https://openairdocs.org/ad/2005-04-10): Stage 1 compressor disks · General Electric T58-GE-100, T58-GE-10, T58-GE-5 and 2 more. Effective Mar 29, 2005
- [AD 2004-04-06](https://openairdocs.org/ad/2004-04-06): Fuel flow divider assemblies · General Electric T58-GE-402, T58-GE-100, T58-GE-10 and 8 more. Effective Mar 9, 2004
- [AD 2001-12-07](https://openairdocs.org/ad/2001-12-07): Fuel Flow Divider Assemblies · General Electric T58-GE-402, T58-GE-100, T58-GE-10 and 4 more. Effective Jul 2, 2001
- [AD 97-21-08](https://openairdocs.org/ad/97-21-08): Stage 1 forward cooling plate · General Electric T58-GE-100, T58-GE-10, T58-GE-8F and 6 more. Effective Dec 19, 1997
- [AD 97-19-17](https://openairdocs.org/ad/97-19-17): Critical rotating parts · General Electric T58-GE-100, T58-GE-10, T58-GE-5 and 6 more. Effective Nov 28, 1997
- [AD 94-07-05](https://openairdocs.org/ad/94-07-05): Turbine Wheels · General Electric CT58-110-1, CT58-110-2, CT58-140-1 and 1 more. Effective Apr 19, 1994
- [AD 91-07-17](https://openairdocs.org/ad/91-07-17): Gas Generator · General Electric CT58-140-1. Effective Apr 26, 1991
- [AD 81-18-03](https://openairdocs.org/ad/81-18-03): Fuel Controls · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Sep 17, 1981
- [AD 81-02-02](https://openairdocs.org/ad/81-02-02): Stage One Turbine Wheels · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Feb 2, 1981
- [AD 78-26-08](https://openairdocs.org/ad/78-26-08): Lube Pump Drive Shaft · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Dec 19, 1978
- [AD 67-01-02](https://openairdocs.org/ad/67-01-02): Rotor Discs · General Electric CT58-100-1, T58-GE-5, T58-GE-1 and 5 more. Effective Aug 24, 1976
- [AD 76-13-02](https://openairdocs.org/ad/76-13-02): Oil Cooler-To-Fuel Filter Hose · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Jul 6, 1976
- [AD 74-25-01](https://openairdocs.org/ad/74-25-01): Fuel System Hose · General Electric CT58-140-1 and CT58-140-2. Effective Dec 10, 1974
- [AD 69-17-03](https://openairdocs.org/ad/69-17-03): First and Second Stage Turbine Rotor Discs · General Electric T58-GE-5, T58-GE-1, CT58-100-2 and 4 more. Effective Aug 27, 1969
- [AD 64-26-02](https://openairdocs.org/ad/64-26-02): Starter Drive Shaft Bearing · General Electric CT58-100-1, T58-GE-5, T58-GE-1 and 3 more. Effective Jun 3, 1966
- [AD 2008-22-16](https://openairdocs.org/ad/2008-22-16) (historical): Repetitive heavy lift (RHL) · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Dec 1, 2008
- [AD 2001-18-06](https://openairdocs.org/ad/2001-18-06) (historical): Engine Life-limited Rotating Parts · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Oct 18, 2001
- [AD 69-23-02](https://openairdocs.org/ad/69-23-02) (historical): Stage 2 Compressor Rotor Disc Shafts · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more. Effective Oct 15, 1970
- [AD 79-23-04](https://openairdocs.org/ad/79-23-04) (historical): Turboshaft Engines Rotating Components · General Electric CT58-100-2, CT58-110-1, CT58-110-2 and 2 more

## Registered aircraft by registry model (OpenAirDocs)

- [GE CT58-140-2](https://openairdocs.org/engine/ge-ct58-140-2): 33 aircraft (registry code 30129)
- [GE CT58-140-1](https://openairdocs.org/engine/ge-ct58-140-1): 20 aircraft (registry code 30128)
- [GE CT58-100-2](https://openairdocs.org/engine/ge-ct58-100-2): 0 aircraft (registry code 30125)
- [GE CT58-110-1](https://openairdocs.org/engine/ge-ct58-110-1): 0 aircraft (registry code 30126)
- [GE CT58-110-2](https://openairdocs.org/engine/ge-ct58-110-2): 0 aircraft (registry code 30127)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.
