# TCDS A36EU: CEAPR - Type: Type certificate data sheet - Status: Current - Holder: CEAPR - Revision: 6 - Revised: January 15, 2020 - Product: Aircraft, Small Airplane - Certification basis: Part 21, Part 23 - Registered aircraft: 22, by the registry models matched to it (OpenAirDocs) - Data sheet PDF: https://openairdocs.org/files/sha256/87/e6/87e657c0dae78cdd11bf2251d4e79086cc7e87cf1e6c6c9f3185c5dd38dc4691 - FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/1C64AE7F20CB13AE862584F900489E32.0001 - Page: https://openairdocs.org/tcds/A36EU ## Models (1) As the data sheet lists them. - CAP 10 B ## What the data sheet says From the PDF's text layer, line by line; tables lose their columns. The PDF is the record. ```text Page No 1 2 3 4 5 6 Rev No 6 4 5 5 5 6 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION A36EU Revision 6 CEAPR CAP 10 B January 15, 2020 TYPE CERTIFICATE DATA SHEET No. A36EU This data sheet, which is a part of Type Certificate No. A36EU, prescribes conditions and limitations un der which the product for which the Type Certificate was issued meets the airworthiness requirements of the Federal Aviation Regulations. Type Certificate Holder: CEAPR 1 Route de Troyes 21121 Darois, France Type Certificate Holder Record: AVIONS MUDRY et CIE was previous holder of A36EU. Effective July 18, 2002, APEX became TC holder. TC A36EU was transferred to CEAPR on September 21, 2015. Previous holders of TC A36EU include Akrotech Europe, CAP Aviation, Dyn’Aviation, AUPA DYN’AERO, and AERODIF. (See Note 11.) Revision No. 4 adds Major Wing Change 000302 to this data sheet of the APEX Aircraft Model CAP 10B. I – Model CAP 10 B (Utility and Acrobatic Category), approved June 13, 1974 Engine Lycoming IO360 B2F with “Christen” inverted oil system, or Lycoming AEIO360-B2F fuel injected, US TC No. 1E10 Fuel 91/96 minimum aviation grade gasoline. Engine limits For all operations, 2700 r.p.m. (180 HP) Propeller Hoffman HO 29-180-170 EVRA CAP 3.180.170.H5.F, US TC No. P3EU Propeller Limits (Utility and Acrobatic Categories) Static r.p.m. at maximum permissible throttle setting 2200 rpm Diameter 70.9 inches. No cutoff permitted. Airspeed limits Utility Category Acrobatic Category VNE Never exceed 211 m.p.h. (183 kts) 211 m.p.h. (183 kts) VC Design cruising 186 m.p.h. (162 kts) 186 m.p.h. (162 kts) A36EU Page 2 of 6 VA Maneuvering 124 m.p.h. (108 kts) 146 m.p.h. (127 kts) VF Flaps extended 99 m.p.h. ( 86 kts) 99 m.p.h. (86 kts) See NOTE 3 for acrobatic maneuvers Flight Maneuvering Load Flaps up +4.4 +6.0 Factor (G’s) -1.8 -4.5 Flaps down +2.0 +2.0 -1.8 -2.0 C.G. range Forward limit +10.6 in. (18%) 10.6 in (18%) Aft limit +17.7 in. (30%) 15.3 in (26%) Datum Wing leading edge at 51 in. from airplane centerline. (Length of wing chord at datum 59 inches). Leveling Means Longitudinal: Left canopy rail horizontal Transverse: Top of bulkhead #2 Empty weight C.G. range None. Maximum weight Takeoff 1830 lb. 1675 lb. Landing 1763 lb. 1675 lb. No. of seats 2 at +23.6 in. 2 at + 23.6 in. Maximum baggage 110 lb. At +55.1 None Fuel capacity Front tank (total) 19.8 (at–9.6 in.) 19.8 (at–9.6 in) See Note 9. (usable) 19.0 19.0 Rear tank (total) 20.8 (at. 49.6 in) 0 (usable) 20.6 0 Rear tank must be empty for operations in acrobatic category. Minimum fuel quantity for acrobatics: 2.6 U.S. gal. Oil capacity Minimum capacity: 8 quarts Minimum: 2 quarts Maximum oil quantity for acrobatics: 6 quarts Control surface Aileron Up 25º ± 2 Down 15º ± 2 movements Elevator Up 25º ± 2 Down 25º ± 2 Elevator trim tab Up 24º ± 2 Down 14º ± 2 Rudder Right 18º ± 2 Left 18º ± 2 Wing Flaps Takeoff 15º ± 2 Landing 40º ± 2 Serial Nos. Eligible A French “Certificat de Navigabilite pour Exportation” endorsed as noted under “Import Requirements”, must be submitted for each A36EU Page 3 of 6 individual aircraft for which application for U.S. certification is made. Certification Basis FAR 21.29: French AIR 2052 with Amendments dated October 7, 1965 (equivalent to FAR 23 effective February 1, 1965); Type Certificate No. A36EU issued June 13, 1974. - Date of application for type certification: April 26, 1973 The Direction Generale de l’Aviation Civile (DGAC) originally type certificated this aircraft under its type Certificate Number TC 55. Effective September 28, 2003, the European Aviation Safety Agency (EASA) began oversight of this product under their type certificate Number TC 55 on behalf of France. Equipment The basic required equipment as prescribed in the applicable airworthiness regulations (see Certification Basis) must be installed in the aircraft for certification. In addition the following is required: CAP Aviation Flight Manual, Document No. 1000977, December 1989, Revision 7, dated November 27, 2001 or later approved revisions. The Import requirements For aircraft produced in France, The FAA can issue a U.S. airworthiness certificate based on an NAA Export Certificate of Airworthiness (Export C of A) signed by a representative of the Direction Generale de l’Aviation Civile (DGAC) on behalf of the European Community. The Export C of A should contain the following statement “The aircraft covered by this certificate has been examined, tested, and found to comply with Code of Federal Regulations approved under U.S. type certificate no. A 36EU and to be in a condition for safe operation”. Service Information Each of the documents listed below must state that it is approved by the European Aviation Safety Agency (EASA) or – for approvals made before September 28, 2003- by the Direction Generale de l’Aviation Civile (DGAC) · Service bulletins · Structural Repair Manuals · Vendor Manuals · Aircraft Flight Manuals, and · Overhaul and Maintenance Manuals The FAA accepts such documents and considers them FAA-approved unless one of the following condition exists: · The documents change the limitations, performance, or procedures of the FAA approved manuals; or · The documents make an acoustical or emissions changes to this product’s U.S.type certificate as defined in 14 CFR § 21.93. The FAA uses the post type validation procedures to approve these documents. The FAA may delegate on case-by-case to EASA to approve on behalf of the FAA for the U.S. type certificate. If this is the case it will be noted on the document. A36EU Page 4 of 6 II. Major Change 000302, Wing Change, approved June 16, 2004 (Commercial name: CAP10C) Same as Model CAP 10 B except: Utility Category Acrobatic Category Maximum weight (no change) 1720 lb. C.G. range Forward Limit +11.8 in. (20%) 11.8 in. (20%) Control surface movements Aileron Up 25º ± 2 Down 25º ± 2 Certification Basis 14 CFR Part 23 effective February 1, 1965, including Amendments 23-1 through Amendment 23-46 as it applies to the wing only. Under the Bilateral Airworthiness Agreement between the USA and the French DGAC, an application to amend their U.S. Type Certificate was submitted by APEX Aircraft for their Model CAP 10B on December 12, 2002 and their application was assigned an FAA project no. CE0602SN on February 3, 2003. The Direction Generale de l’Aviation Civile (DGAC) originally type certificated this aircraft under its type Certificate Number TC 55. Effective September 28, 2003, the European Aviation Safety Agency (EASA) began oversight of this product under their type certificate Number TC 55 on behalf of France. Equipment The basic required equipment as prescribed in the applicable airworthiness regulations (see Certification Basis) must be installed in the aircraft for certification. In addition the following is required: APEX Aircraft Flight Manual Document No. 1000809 dated May 18, 2004 or later approved revisions. See Note 2, Note 8. Import requirements For aircraft produced in France, The FAA can issue a U.S. airworthiness certificate based on an NAA Export Certificate of Airworthiness (Export C of A) signed by a representative of the Direction Generale de l’Aviation Civile (DGAC) on behalf of the European Community. The Export C of A should contain the following statement “The aircraft covered by this certificate has been examined, tested, and found to comply with Code of Federal Regulations approved under U.S. type certificate No. A 36EU and to be in a condition for safe operation”. Service Information Each of the documents listed below must state that it is approved by the European Aviation Safety Agency (EASA) or – for approvals made before September 28, 2003- by the Direction Generale de l’Aviation Civile (DGAC). · Service bulletins · Structural Repair Manuals · Vendor Manuals · Aircraft Flight Manuals, and · Overhaul and Maintenance Manuals The FAA accepts such documents and considers them FAA-approved unless one of the following condition exists: A36EU Page 5 of 6 · The documents change the limitations, performance, or procedures of the FAA approved manuals; or · The documents make an acoustical or emissions changes to this product’s U.S.type certificate as defined in 14 CFR § 21.93. The FAA uses the post type validation procedures to approve these documents. The FAA may delegate on case-by-case to EASA to approve on behalf of the FAA for the U.S. type certificate. If this is the case it will be noted on the document. NOTE 1. Current weight and balance report, including list of equipment in certificated empty weight and loading instructions if applicable, must be in each aircraft at the time of original certification. Empty weight must include unusable fuel of 5 lbs. (-9.6) and 2 lbs. At (+49.6). See NOTE 9. NOTE 2. In addition to the placards required in the approved Airplane Flight Manual, the following placards must be installed in the appropriate locations as indicated: 1. In full view of the pilot Limits of Utilization Utility Category: AU W takeoff 1830 lb. AU W landing 1763 lb. Load factors +4.4, -1.8 No acrobatic maneuvers, including spins, approved. Acrobatic Category: AU W takeoff and landing 1675 lb. Load factors +6, -4.5 For Major Change 000302: AU W 1720 lb. No Smoking No objects permitted on floor. Va = 146 m.p.h. 2. In the Baggage Compartment Baggage “U” Category - 110 lb. Max (See Weight and Balance Data) “A” Category – No baggage permitted. 3. Approved Acrobatic Maneuvers: Minimum Entry Speed One Pilot Two Pilots Loop 138 m.p.h. (120 kts) 144 m.p.h. (125 kts) Half Cuban eight 132 m.p.h. (115 kts) 138 m.p.h. (120 kts) Roll 132 m.p.h. (120 kts) 144 m.p.h. (125 kts) Positive snap roll NOTE 8 92 m.p.h. (86 kts) 99 m.p.h. (86 kts) Negative snap roll NOTE 8 92 m.p.h. (86 kts) 92 m.p.h. (86 kts) Inverted loop 155 m.p.h. (135 kts) 167 m.p.h. (146 kts) Hammerhead 127 m.p.h. (108 kts) 127 m.p.h. (108 kts) A36EU Page 6 of 6 NOTE 3. Airspeed indicator markings (Acrobatic Category) Radial red line 211 m.p.h.(185 kts) Yellow arc 186 to 211 m.p.h. (162 to 183 kts) Green arc 62 to 186 m.p.h. (54 to 162 kts) White arc 53 to 100 m.p.h. (46 to 86 kts) Radial yellow line 146 m.p.h.(126 kts) NOTE 4. Cylinder head temp. Gauge marking red line at 500º F (260º C) Green arc 150º F (66º to 204º C) Oil temperature gauge marking Red line at 244º F Green arc 104º F to 244º F (40º C to 118º C) NOTE 5. Oil pressure gauge marking Red line at 100 p.s.i. (7.03 bars) Green arc 60 to 90 p.s.i. (4.22 to 6.33 bars) Yellow arc 26 to 62 p.s.i. (1.76 to 4.22 bars) NOTE 6. Tachometer marking Green arc 500 r.p.m. to 2700 r.p.m. Radial red line at 2700 r.p.m. NOTE 7. G. Meter marking Green arc –4.5 to +6 Red line at –4.5 and +6 NOTE 8. CAP10B with Change 000302: Snap maneuver is limited to a MAXIMUM entry speed of (160 k/h), 99 mph, 86 knots. NOTE 9. Moment Arms corrected in Revision 4. Previous values were incorrect, but conservative. NOTE 10. Airworthiness Limitations are contained in the FAA approved, or DGAC approved for the FAA, Chapter 4 of the CAP 10B Aircraft Maintenance Manual. These Limitations may not b e changed without FAA approval, or DGAC approval for the FAA. NOTE 11. Some of these transfers were not notified to the FAA and so in some instances the actual type certificates were not reissued. ….END…. ``` ## ADs (15, in force first) - [AD 2011-06-01](https://openairdocs.org/ad/2011-06-01): Flight Controls · APEX CAP 10 B. Effective Apr 13, 2011 - [AD 2008-17-07](https://openairdocs.org/ad/2008-17-07): Flight controls tie rod · APEX CAP 10 B. Effective Sep 23, 2008 - [AD 2008-13-32](https://openairdocs.org/ad/2008-13-32): Luggage compartment · APEX CAP 10 B. Effective Aug 12, 2008 - [AD 2008-09-02](https://openairdocs.org/ad/2008-09-02): Upper spar flange inspection · APEX CAP 10 B. Effective May 27, 2008 - [AD 2008-07-04](https://openairdocs.org/ad/2008-07-04): Control stick base cover · APEX CAP 10 B. Effective Apr 30, 2008 - [AD 2008-07-05](https://openairdocs.org/ad/2008-07-05): Front fuel tank · APEX CAP 10 B. Effective Apr 30, 2008 - [AD 2007-13-14](https://openairdocs.org/ad/2007-13-14): Lower rudder support · APEX CAP 10 B. Effective Aug 3, 2007 - [AD 2007-10-13](https://openairdocs.org/ad/2007-10-13): Aileron spades · APEX CAP 10 B. Effective Jun 21, 2007 - [AD 2007-09-05](https://openairdocs.org/ad/2007-09-05): Reduced elevator deflection · APEX CAP 10 B. Effective Jun 4, 2007 - [AD 2007-09-06](https://openairdocs.org/ad/2007-09-06): Central wing spar block · APEX CAP 10 B. Effective May 21, 2007 - [AD 91-23-03](https://openairdocs.org/ad/91-23-03): Fuel System · APEX CAP 10 B. Effective Dec 10, 1991 - [AD 2003-04-02](https://openairdocs.org/ad/2003-04-02) (historical): Inspection Opening in Wing · APEX CAP 10 B. Effective Apr 4, 2003 - [AD 99-21-23](https://openairdocs.org/ad/99-21-23) (historical): Flight Manual - Airspeed · APEX CAP 10 B. Effective Dec 3, 1999 - [AD 98-12-10](https://openairdocs.org/ad/98-12-10) (historical): Wing Main Spar · APEX CAP 10 B. Effective Jul 17, 1998 - [AD 93-10-11](https://openairdocs.org/ad/93-10-11) (historical): Wing Spar · APEX CAP 10 B. Effective Jul 23, 1993 ## Registered aircraft by registry model (OpenAirDocs) - [Avions Mudry ET Cie CAP 10B](https://openairdocs.org/model/avions-mudry-et-cie-cap-10b): 22 aircraft (registry code 0950102) - [Akrotech Europe CAP 10B](https://openairdocs.org/model/akrotech-europe-cap-10b): 0 aircraft (registry code 0950104) ## STCs approved under this data sheet (22) - [STC SA04652CH](https://openairdocs.org/stc/SA04652CH): To allow use of 100R grade aviation fuel meeting Swift Fuel, LLC specification. Swift Fuels LLC - [STC SA01757WI](https://openairdocs.org/stc/SA01757WI): To allow the use of UL91 or UL94 (minimum) grade aviation fuel. Swift Fuels LLC - [STC SA04568CH](https://openairdocs.org/stc/SA04568CH): Installation of the uAvionix tailBeaconX, a tail mounted position light with integrated Automatic Dependent Surveillance - Broadcast (ADS-B) Out and 1090MHz Mode-S transponder functionality. uAvionix Corporation - [STC SA02019WI](https://openairdocs.org/stc/SA02019WI): Installation of the Trig Avionics TX56, TX56A, TX57, or TX57A VHF Nav-Com Radio.. Peregrine - [STC SA00756DE](https://openairdocs.org/stc/SA00756DE): Installation of Automatic Dependent Surveillance Broadcast (ADS-B) Out Equipment using a Trig Avionics TT22 Transponder and an approved Global Positioning System (GPS) Position Sensor. Peregrine - [STC SA02444AK](https://openairdocs.org/stc/SA02444AK): Approval of the L-3 Communications NGT 9000/9000R ADS-B system installed. ADS-B Technologies LLC - [STC SA03819NY](https://openairdocs.org/stc/SA03819NY): Installation and maintenance of Oratex 6000 Covering and Coating System. Lanitz-Prena Folien Factory GmbH - [STC SA11174SC PAGE 1](https://openairdocs.org/stc/SA11174SC%20PAGE%201): Installation of BendixKing by Honeywell KSN 770 and KSN 765 WAAS LPV approach capable nav/comm systems. Honeywell International Inc (Bendix King) - [STC SA10822SC](https://openairdocs.org/stc/SA10822SC): Installation of EFD1000 Primary Flight Display. Aspen Avionics Inc. - [STC SA00410BO](https://openairdocs.org/stc/SA00410BO): Installation of an AV-30-C Multi-Mode Indicator. uAvionix Corporation - [STC SA02268CH](https://openairdocs.org/stc/SA02268CH): Installation of Airwolf Filter Corp. Air Oil Separator. Airwolf Filter Corporation - [STC SA00744DE](https://openairdocs.org/stc/SA00744DE): Installation of the Automatic Dependent Surveillance Broadcast (ADS-B) Out Equipment using a Trig Avionics TT31 Transponder and an approved position sensor. Peregrine - [STC SA00765DE](https://openairdocs.org/stc/SA00765DE): Installation of Automatic Dependent Surveillance Broadcast (ADS-B) Out functionality using the BendixKing KT74 Transponder and qualified position sensor. Peregrine - [STC SA01435SE](https://openairdocs.org/stc/SA01435SE): Installation of J.P. Instruments (JPI) Primary Engine Data Management System. J. P. Instruments - [STC SA01835WI](https://openairdocs.org/stc/SA01835WI): Installation of Trig Avionics TY-96 or TY-97 VHF Communications Radio. Peregrine - [STC SA00024NY](https://openairdocs.org/stc/SA00024NY): Installation of Airwolf remote mounted engine oil filter kit AFC-K007 on single or multi-engine fixed wing light aircraft incorporating Lycoming reciprocating engines of 450 horsepower or less.. Airwolf Filter Corporation - [STC SA00478CH](https://openairdocs.org/stc/SA00478CH): Installation of Cooper Superflite 102 Fabric.. Aviation Products Systems Inc. - [STC SA563CH](https://openairdocs.org/stc/SA563CH): Authorizes installation of engines equipped w/Unison Limited Authority Spark Advance Regulator (LASAR) ignition system w/Cylinder Head Temp. (CHT) monitoring capability on airframes. engines.. Champion Aerospace LLC - [STC SA593CH](https://openairdocs.org/stc/SA593CH): Install Champion SlickSTART magneto booster system.. Champion Aerospace LLC - [STC SA5159NM](https://openairdocs.org/stc/SA5159NM): Installation of chip detector system.. Northwest Aircraft Inc - [STC SA001410BO](https://openairdocs.org/stc/SA001410BO) (historical): Installation of an AV-30-C Multi-Mode Indicator. uAvionix Corporation - [STC SA00765DE PAGE 1](https://openairdocs.org/stc/SA00765DE%20PAGE%201) (historical): Installation of Automatic Dependent Surveillance Broadcast (ADS-B) Out functionality using the BendixKing KT74 Transponder and qualified position sensor. Peregrine --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.